Oricom TP58 User's Manual
Contents
1. To use the redial facility proceed as follows 1 Lift the handset 2 Press the REDIAL button the last saved redial number will now be dialled 4 3 Recall button You will use the RECALL button when using your network operator s services such as call waiting etc If this feature is not working check the position of the Recall switch on the side of the phone In Australia it should be set at 100ms and in New Zealand 600ms 4 4 Muting the microphone You can switch off the microphone during a call using the MUTE button It is then possible to speak without the other party hearing you You can still hear the other party To mute the microphone press and hold the MUTE button during a call Release the MUTE button and you can continue the call as normal 5 Storing telephone numbers You can store 6 numbers under the one touch buttons M1 M6 5 1 Saving numbers 1 Lift the handset listen for dial tone Press the STORE button Enter the required telephone number using the number pad Press the STORE button Now press one of the six one touch dial buttons M1 M6 Replace the handset OAR Tips on storing numbers Storage locations that have already been used cannot be erased Simply save a new number in the storage location that you want to erase The storage locations can be written on the index card so that you do not forget where the numbers have been stored You can remove the protective transparent cover using the tip2. Oricom Big button phone TP58 User Guide 1 General Information Warnings Do not use your telephone during an electrical storm thunderstorm as it is possible to get an electric shock Refer to information contained in Telstra White pages directory The earpiece of the handset may attract small metal objects such as staples and pins Care should be taken when placing the handset near these items Notes for operation in New Zealand The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with the minimum conditions for connection to its network It indicates no endorsement of the product by Telecom nor does it provide any sort of warranty Above all it provides no assurance that any item will work correctly in all respects with another item of Telepermitted equipment of a different make or model nor does it imply that any product is compatible with all of Telecom s network services This equipment shall not be set to make automatic calls to the Telecom 111 Emergency Service This equipment may not provide for the effective hand over of a call to another device connected to the same line This device may be subject to ringing or bell tinkle when certain other devices are connected to the same line If this occurs the problem should not be referred to the Telecom Faults Service REN RN for New Zealand The REN Ringer Equivalence Number or RN is of sign
3. for desk installation into the wall socket Plug the other end into the socket located in the indentation on the base of the telephone Then feed the cable through the cable guide 3 3 Wall mounting Method A Use two screws for fixing At the desired location drill two holes one above the other 83mm apart and leave the screws protruding 5mm from the wall Now place the telephone base over the screws and gently push forwards and then downwards Method B If you wish to fit to an existing telephone wall plate with modular connector Plug the short telephone line cord supplied into the base of the phone plug the other end into the telephone wall plate socket Position the mounting holes on the base of the phone over the two protruding screws on the wall plate Gently push the phone flush against the wall plate then slide the phone downwards locking it into place NOTE There is a small hanging device in the handset rest to prevent the handset from falling from the rest when the telephone is mounted on the wall You can hang the handset on the telephone without hanging up Use the small hanging device for this purpose at the upper end of the handset rest 3 4 Adjustable ringer volume You can use the RINGER OFF LO HI slide switch located on the back of the telephone to select the incoming ring volume Should you not want to be disturbed use select OFF position 3 5 Receiver volume control The receiver volume control is located on
4. ificance only if you wish to connect more than 1 telephone to your telephone line A standard telephone line has a maximum REN capacity of 3 RN of 5 It is possible to connect 3 5 devices with a REN of 1 RN of 1 with no degradation to the products performance Exceeding this limit may cause the volume of the ringer in any phone to decrease or not ring at all 2 Location of controls Oricom 11 Oar 13 14 Hook switch Receiver volume control Store button 6 one touch memory buttons Recall button Mute button Ringer Hi Lo Off switch Recall setting switch Speaker 10 Visual ringer light 11 Keypad 12 Speaker volume control 13 Redial button 14 Speaker button with LED A N13134 The A Tick symbol indicates that this product complies with all current Australian ACA standards 0 00 NI 0 NS 3 Installation 3 1 Check contents of pack The following items are supplied in this pack one telephone base one telephone handset one short telephone cable one curly cord one long telephone cable one operating Manual one warranty card 3 2 Connect the handset and line cord Connect the telephone handset to the base unit Plug one end of the curly cord into the socket on the handset Locate the socket on the base of the phone and plug the other end of the curly cord into this Plug one end of the telephone cable long
5. of a ballpoint pen or a small pin 5 2 Making a call using the one touch dial buttons 1 Lift the handset or press SPEAKER button 2 Now press the required one touch dial button M1 M6 The stored number will now be dialled automatically 3 To end the call replace the handset or press SPEAKER button 6 Important information Troubleshooting If you feel this product is not working correctly please consult the user guide and ensure that you are using the product in accordance with the instructions Remove all extra telephone equipment and connect only this telephone directly to the telephone socket If the fault is still present connect another telephone if available to the telephone socket The results will show you whether the fault lies with this product or with the telephone line If this product is working correctly the fault is on the telephone line Please contact your network operator for assistance In the case of technical problems with this product please consult our website for further information or send us an email for a prompt response to your enquiry Temperature and ambient conditions The telephone is designed for indoor use temperature range of 10 C to 50 C Do not install the telephone in areas where there is the risk of an explosion excessive exposure to smoke dust vibrations chemicals moisture and heat The unit must not be installed in damp locations such as a bathroom or laundry do not exp
6. om au Web www oricom com au Fax 02 4574 8898 Ph 1300 889 785 New Zealand Atlas Gentech NZ Ltd Private Bag 14927 Panmure Auckland Customer Support Email support atlasgentech co nz Fax 09 5742722 Ph 0900 50025 Toll Call 41M114Y1
7. ose the unit to direct sunlight Cleaning and care The surface of the case can be cleaned with a dry soft lint free cloth Never use cleaning agents particularly aggressive solvents Apart from occasional cleaning of the case no other care is necessary The rubber feet of the base station are not resistant to all cleaning agents The telephone feet do not normally leave any marks on the surface However on account of the multitude of varnishes and surface finishes used surface marks caused by the feet of the unit cannot be ruled out Warranty Information This product is covered by a 12 month warranty against defective workmanship or parts effective from the date of purchase The warranty does not extend to damage caused by misuse negligence excessive voltage faults on the telephone line or lightning This warranty in no way affects your statutory rights Full details of the warranty are contained in the enclosed warranty card Technical support In the unlikely event of a fault during this period please consult our website for assistance or send us an email for a prompt response to your enquiry If the product is then found to be faulty you will be asked to return it directly to us with a copy of the purchase receipt For further information about the Oricom range of products please visit our website Australia Oricom International Pty Ltd Locked Bag 658 South Windsor NSW 2756 Customer support Email support oricom c
8. the handset of your phone This enables you to adjust the receiver volume from low LO middle MID to high HI for a better listening level 3 6 Speaker Volume Control Under Speaker phone mode slide the SPEAKER VOL to adjust the speaker phone volume 4 Operation 4 1 Using the telephone The TP58 telephone is used like any conventional telephone and works with all modern telephone exchanges using the tone dialling system Use can make or receive a call using handset or speakerphone Dialing a call 1 Lift the handset or press SPEAKER button SPEAKER LED turns on and wait until your hear dial tone 2 Now dial the required telephone number 3 To end the call replace the handset or press SPEAKER button SPEAKER LED turns off Receiving a Call When you receive a call the phone rings and the Visual ringer light flashes To answer the call lift the handset or press SPEAKER button SPEAKER LED turns on Replace the handset or press SPEAKER button SPEAKER LED turns off to end the call NOTE If you want to change during a call from the handset to the speakerphone press the SPEAKER button and replace the handset If you want to change from the speakerphone to the handset simply lift the handset 4 2 Last number redial If the number you have dialed is engaged or you were unable to get through to anybody simply replace the handset The last number up to 32 digits dialled will be saved in the telephone memory
Download Pdf Manuals
Related Search