Oreck XLS700 User's Manual
Contents
1. OREGK XL SIMPLY AMAZING User s GUIDE RINSE A MATIC STEEMER CARPET amp HARD FLOOR CLEANER XLS7 00 series IMPORTANT SAVE THIS BOOKLET Includes e Warranty e Safety Warnings e Parts List e Operating Instructions e Accessories List e Trouble Diagnosis BEFORE OPERATING CLEANER READ ALL INSTRUCTIONS IN THIS MANUAL CAREFULLY Table of Contents Maintenance and Customer Service Polarized Plug Notice Accessories Important Safety Instructions page 1 Warranty Troubleshooting Guide page 2 Figures cs a td ma page 3 Parts Checklist Features To Assemble Cleaner page 4 Servicing of double Insulated Appliances A L C l To Set Up Cleaner To Prepare Carpet Operating Inst page 5 Operating Instructions 0 0 0 2 eee eee page 6 To Clean Carpet Cleaner To Store Cleaner Things To Do To Replace Belt 2 02 carr a ewe aa page 7 Maintenance and Customer Service Your ORECK STEEMER is a product of precise engineering The motor bearings are permanently lubricated and should not be oiled If you require additional information or have problems with your Oreck appliance you may call ORECK CUSTOMER SERVICE at US 1 800 989 3535 Canada 1 888 676 7325 Please specify the model number and serial code number which can be found on the data plate on the back of the vacuum Save your sales or purchase slip Should your Oreck a2. Not removing certain stains Heavy traffic area spots For best results use a stain pretreatment such as Steemer Full Release Professional Spot amp Stain PreCleaner These solutions loosen and break down most common household grease oil and food stains Make several slow passes over the stain from different angles Carpet is excessively wet after cleaning Note Under normal conditions a carpet may take up to four hours or longer to completely dry Drying time depends on a combination of various factors including carpet type carpet pile thickness temperature humidity air circulation and the number of wet passes e Make at least one additional pass over the wet carpet without pressing the cleaner button Check that the handle trigger lock is not engaged With each pass slowly pull the unit toward you to extract any remaining liquid in the carpet To speed drying gently push the nozzle deep into the carpet pile Check for airpath obstructions in the stair upholstery hose cleaner neck and in the nozzle Check to insure that the inlet screen is free of debris Excessive foaming at spray tips Check that the upper supply tank has water Dark streaks on carpet after cleaning Operate the machine more slowly you will achieve better results with one slow pass than several fast strokes Overlap each pass to provide maximum cleaning without streaking In high traffic or heavily soiled
3. Lock in Cleaner Cartridge Bottle Screws 5 8 4 Hand held Nozzle and Hose Assembly No ut fF WOM gt Features 25 Power Cord A L C Safety Plug with Reset and Test Buttons Translucent Upper Supply Tank Translucent Lower Recovery Tank Transparent Nozzle Cover Motorized Scrubbing Brush Convenient quick release Cord Wrap Wiper for hard floor cleaning Temperature Indicating Label 17 Floor Stand RED OPERATOR CONTROLS 18 Rinse Shampoo Valve 19 Shampoo Cleaner Spray Button 20 A L C l Plug Reset Button 21 Tank Latch 22 On Off Power Switch 23 Nozzle Change Button 24 Hand held Nozzle Trigger a a a k 1 O DONADOS To Assemble Cleaner THE ONLY TOOL YOU WILL NEED IS A PHILLIPS TYPE SCREWDRIVER fig 1 Attach Handle to Cleaner a Lay the cleaner on a flat surface with the tank side down or to its side b Slide handle into cleaner body until interlock is secured c Insert four 58 screws included into the four cavities in the handle base and tighten fig 2 Attach Wheels a Locate two wheels and two support legs b Insert the wheels a into the support legs b by pushing the wheels in until they snap into place fig 3 Attach Nozzle Turn the unit so that the tank is face up a Align the nozzle so the red nozzle change button is in line with the corresponding hole in the nozzle Depress the small red nozzle change button and slide the nozzle over the un
4. carpets it is occasionally beneficial to allow the carpet to dry and repeat the process as needed to achieve optimal cleaning Steemer brush roll will not turn Check that the nozzle power cord is completely connected to the main unit If an obstruction stalls the brush roll the belt is designed to burn through so as to protect the motor Please insure through inspection that the brush roll is free of obstructions and is free to turn Secondly make sure that the belt is in good working order Replace the belt if needed If the belt and the brush roll become excessively wet momentary slippage can occur By running the unit on a dry section of carpet for a minute or less the belt will function properly Cleaner will not run or suddenly stops e Reinsert the plug if it has slipped out of the outlet The A L C I may have tripped off due to fluctuations in household current Press the reset button and restart the unit ALL OTHER SERVICING SHOULD BE DONE BY AN ORECK AUTHORIZED SERVICE CENTER Parts Checklist Read all instructions thoroughly before assembly use Please unpack carton removing all parts and packages Check that all parts required for assembly are present by referencing the list below PARTS QUANTITY Oreck Steemer Unit 1 Handle Oreck Steemer Power Nozzle Large easy to steer Wheels 2 Easy
5. immerse the power nozzle of the Oreck Steemer 3 Do not allow the lower recovery tank to overfill 4 Do not pick up corrosive combustible or flammable liquids such as acids gasoline alcohol or use this product in areas where vapors from these types of materials are present 5 Do not use to clean out bathtubs flooded basements or any place where the liquid depth exceeds 1 8 To Clean Carpet Cleaner WARNING To reduce the risk of electric shock or injury from moving parts unplug before servicing Before turning the cleaner off tilt the cleaner back raising the nozzle off the carpet for 15 20 seconds This prevents extracted water in the nozzle from dripping back onto the carpet after you turn the cleaner off fig 13 Place the power switch in the OFF position Unplug the power cord from the outlet fig 11 Remove the cleaner cartridge by rotating the locking white lever upwards Do not store with a cleaner cartridge attached fig 19 Remove and empty the tank Rinse out the lower recovery tank with warm water Wipe off the inlet screen to remove accumulated dirt lint and debris fig 10 Replace tank fig 20 If you have been operating the cleaner at length it may be necessary to clean the nozzle from time to time particularly if the carpet is brand new or very dirty or if long haired pets frequently use the carpeted area Unplug cleaner and examine several areas on the power nozzle to see if debris has
6. or use in areas where they may be present Do not use appliance in an enclosed space where flammable explosive or toxic vapors are given off by oil base paint paint thinner some mothproofing substances or in an area where flammable dust is present Immediately switch off and unplug appliance if water or cleaning solution is observed leaking from machine during operation To prevent over filling the recovery water tank empty the recovery water tank every time the clean water tank is filled Always turn off the appliance before connecting or disconnecting motorized nozzle SAVE THESE INSTRUCTIONS Household Use Only Warranty ORECK MANUFACTURING COMPANY Oreck Manufacturing Company gives you the following limited warranty for this product only if it was originally purchased for residential use not resale from Oreck or an Oreck Authorized Retail Dealer Oreck will repair or replace free of charge to the original purchaser any part which is found to be defective in material or workmanship within one 1 year of the date of purchase This limited warranty applies to normal domestic use Any commercial use of this product will void this limited warranty Any use of non Oreck cleaning solutions with this unit will void this limited warranty This limited warranty does not cover the replacement of expendable or consumable parts such as belts brushes and other parts subject to normal wear unless they are defective in material
7. that are free of surface debris To achieve best results high traffic areas and carpet stains should be pretreated prior to cleaning using Steemer Full Release Professional Spot amp Stain PreCleaner CAUTION Before cleaning a carpet for the first time test a small area for color fastness Pour a small amount of Steemer Full Release Professional Carpet Cleaner on a clean white cloth and blot carpet Examine this cloth for color removal if color appears on the cloth the carpeting is not colorfast and should not be cleaned with any wet extraction process NOTE This product is not recommended for use on carpets made from silk velvet wool and some cotton blends Check the manufacturer s cleaning recommendations Operating Instructions To Clean Carpets and Hard Flooring NOTE DO NOT use on Hard Wood Flooring fig 12 Turn the Shampoo Rinse switch to the SHAMPOO position fig 13 Place power switch in the ON position fig 14 Press the red button in the handle and while lifting the handle slightly slowly pull the cleaner backwards Pressing the button releases the cleaner and water mixture As you pull the nozzle over the sprayed floor the nozzle extracts the solution from the floor and stores the dirty water in the recovery tank fig 15 To move forward slightly tilt the nozzle off the floor and roll the cleaner forward Repeat process working in small overlapping rows for even cleaning until the entire ro
8. the guide tab on top of unit s neck with slot in hose collar Depress the red button and push the hose collar onto the unit until the button locks securely in the collar hole fig 13 Place power switch in the ON position fig 14 Press the red button in the handle and push forward to lock fig 18 Press the red cleaner dispensing trigger on the hand held nozzle to release cleaner To Prepare Upholstery IMPORTANT Prior to cleaning any upholstered furniture read the following instructions very carefully Most modern upholstery fabrics may be safely cleaned by wet cleaning methods yet there are exceptions to this as some delicate or unusual fabrics require dry cleaning If you are in doubt about the type of fabric we suggest that you check with the manufacturer or dealer where the furniture was purchased Most fabrics are wear coded by the manufacturer which details cleaning methods for a particular fabric If necessary bring in a cushion or arm cover to your dealer e Cleaning upholstery which is covered with fabrics that are not compatible with wet cleaning may result in damage to the fabric Know what the fabric is and how it may be cleaned before using the Oreck Steemer cleaner e Check the stuffing material if possible Look inside cushions and underneath the furniture If the filling is colored it may bleed through and discolor the furniture Most modern stuffing material is light colored and colorfast To rem
9. ODUCT INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO THE WARRANTY PERIOD AND NO WARRANTIES WHETHER EXPRESS OR IMPLIED WILL APPLY AFTER THIS PERIOD Some states do not allow limitations on the duration of implied warranties so the above limitation may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state CALL CUSTOMER SERVICE HOT LINE US 1 800 989 3535 Canada 1 888 676 7325 Whenever calling please be sure to have your model and serial number from data plate Troubleshooting Guide WARNING Unplug cord from electrical outlet before servicing PROBLEM Water and cleaning solution is not dispensing onto carpet or upholstery SOLUTION Check that the upper supply tank is partially filled with lukewarm water Caution Do not overfill e Check that a cleaner cartridge is installed and that the white lever is locked in the downward position Due to pressurization the cleaner will not properly operate without a cleaner cartridge in place If the cleaner cartridge is empty replace it with a full cartridge Check that the spray tips are not clogged Use a towel or damp cloth to clean For above the floor cleaning check that the hand held nozzle and hose assembly is properly connected to the cleaner neck Also insure that the button lock has been engaged
10. aintenance Cleaning Thorough Pre treat with Spot amp Stain Remover Shampoo Dry Rinse Dry Rinse Dry e Thicker Carpet Pre treat with Spot amp Stain Heavy Duty Cleaning Remover e Traffic Lanes Shampoo Dry Rinse Dry Spots Rinse Dry Hard Floor Cleaning Situation Procedure Quick Clean Shampoo Dry Standard Clean Pre treat with Spot amp Stain Remover as necessary Shampoo Dry Rinse Dry Pre treat with Spot amp Stain Remover Shampoo Dry Rinse Dry Rinse Dr NOTE Additional drying passes can be used to reduce carpet and hard floor moisture and shorten drying time Heavy Duty Clean For Above the Floor Cleaning Cars Stairs Etc CAUTION Set the red button in the handle to the floor back position when using the hand held nozzle for extraction only Unplug the cleaner from the electrical outlet fig 4 You will first need to unplug the separate power cord that connects the Steemer nozzle to the cleaner fig 3 Remove the nozzle by depressing the red button located on the side of the neck Pull the nozzle straight back and off the neck without twisting fig 17 Lower cleaner onto floor stand fig 7 8 Remove the supply recovery tank from the cleaner fig 9 Open tank cap Fill with hot tap water close tank cap fig 10 Replace tank onto cleaner fig 16 Attach the hand held nozzle and hose assembly to the cleaner neck Align
11. built up a Extractor slots b Brush roll chamber c Spray Tips fig 20 To clean the Steemer extractor slots place a cloth or towel over the motor cover to shield and protect the motor from water damage Run hot tap water through the nozzle until clean To clean the brush chamber and spray tips take a towel or damp cloth and wipe clean To Store Cleaner fig 6 Pull the wheel assembly forward toward nozzle for compact storage NOTE Do not store the cleaner in freezing conditions Do not store the cleaner with water in the tank Do not store the cleaner with cleaner cartridge attached Turn the squeegee upside down for storage Squeegee will deform if left in position while in storage Things To Do e Use only manufacturer recommended attachments and accessories e Keep free of dust lint and hair Turn off all controls before unplugging e Test the A L C l plug with every use Empty the recovery tank when full and whenever clean water is added to the supply tank Keep young children and pets away from cleaned carpets until dry e Check carpets and upholstery for color fastness e Clean nozzle periodically To Replace Belt WARNING To reduce the risk of electric shock or injury from moving parts unplug before servicing Replacement belts Part No OR114 for Oreck Steemers are available from Oreck Call Toll Free 1 800 989 3535 fig 4 Unplug the power cord leading from the power head to the rear o
12. completed CAUTION Do not allow the lower recovery tank to overfill Damage to the unit can result Empty the recovery tank when full and whenever clean water is added to the upper supply tank fig 7 To empty the recovery tank simply release the tank latch by squeezing the red and gray latch together fig 8 Lift the tank out and carry it to a sink or drain Turn the tank upside down and pour the dirty water out fig 9 Refill the supply tank with clean hot water Replace cleaner cartridge as needed NOTE Cleaner will not operate without a cleaner cartridge locked into the docking bay For heavily soiled carpets it may be necessary to clean from several directions to insure that the carpet is thoroughly cleaned Sample Cleaning Procedures You can use the Oreck Rinse A Matic Carpet and Hard Floor cleaner in many ways to achieve optimal results The following chart is a guide to usage however feel free to use it in a manner which you think is most effective depending on the surface The procedure section indicates the types of passes to use on the flooring For example Shampoo Dry Rinse Dry means one shampoo pass then one dry pass one rinse pass water only then one dry pass Carpet Cleaning Situation Procedure Monthly Maintenance Cleaning Quick Shampoo Dry Monthly Maintenance Cleaning Standard Pre treat with Spot amp Stain Remover as necessary Shampoo Dry Rinse Dry Monthly M
13. eemer is made to double insulated specifications and is equipped with an A L C l Appliance Leakage Circuit Interrupter The A L C l shuts off the unit in potentially hazardous situations fig 5 The A L C l has a Test and Reset button which should be operated each time the unit is plugged in a Do not remove the tag which provides test instructions from around the cord at the A L C l A L C l may vary from illustration DANGER Improper installation of A L C l can result in electric shock Do not modify or by pass the A L C I Do not replace any electrical component in this product with anything other than an authorized ORECK replacement part The risk of electric shock can result if used in the vicinity of improperly grounded stationary appliances stove refrigerator washer etc To Set Up Cleaner The Oreck Steemer carpet and hard flooring cleaner is designed for fast and easy set up fig 6 Swing the wheels away from the nozzle into the operating position Remove the supply recovery tank fig 7 Pinch the gray and red tank release latch together and gently lower the latch to the nozzle Do Not Force Latch fig 8 Push the supply recovery tank downward toward the nozzle and lift out fig 9 Fill the supply tank a Open the gray tank cap b Fill the tank with hot tap water to the fill line as noted on the side of the tank c Use the temperature label on side of tank to check water temperature OPTIMAL s
14. f the main cleaner fig 3 Remove the power nozzle from the main cleaner fig 21 Disassemble Power Nozzle a Remove screw from belt cover b Remove two 2 screws holding the brush roll clamp in place and remove clamp c Remove and replace the old belt if broken or if excessive wear is noted To Install a New Belt d Remove brush roll and insert the new belt into the rectangular cavity Using a long screwdriver loop belt around motor shaft Pull and stretch belt over crowned end of the brush roll Rotate brush to properly align belt fig 21 Replace belt cover brush roll clamp and screws fig 3 Reattach power nozzle to unit fig 4 Reconnect power cords and test To Replace Squeegee fig 22 Remove squeegee by gently pulling the handles located on each end of the squeegee until it releases a Replace the squeegee by first inserting one tab on the squeegee end with the slot on nozzle Then insert the tab located on other end of squeegee into the nozzle slot NOTE Turn the squeegee upside down for storage The squeegee is designed to assist in hard floor cleaning however it can be left on for carpet cleaning 2002 Oreck Holdings LLC All Rights Reserved All word mark logos product configurations and registered trademarks are owned and used under the authorization of Oreck Holdings LLC Printed in U S A 53320 01 REV E 03 02 ECN R 6359
15. hould be showing on label when the correct water temperature is achieved CAUTION Do not overfill tank or use water that is too cold or too hot Do not put any type of shampoo cleaner into the supply tank Use only Steemer Full Release Professional Carpet Cleaner cartridges which are specifically formulated to be residue free Other carpet shampoo will leave residues in the unit that will over a short period of time clog the dispensing system and void your warranty fig 10 Close tank cap and place the tank back on the cleaner Lift the gray latch to slide the tank upward into position until you hear a click signaling that the tank is securely locked into place Insert Cleaning Cartridge Bottle NOTE Cleaner will not operate without a cleaner cartridge locked into the docking bay Remove the cleaner cartridge bottle cap fig 11 Insert the cleaner cartridge into the docking bay on the side of the cleaner a The directions on the cleaner cartridge must be facing out b Lock and seal the cartridge in the cleaner by rotating the white lever on cartridge from top to bottom Test and reset the A L C fig 5 Plug in the power cord Press the test button to shut off power To reset the A L C l simply push in the red reset button on the plug To Prepare Carpet Always vacuum thoroughly before using the ORECK STEEMER carpet and hard flooring cleaner It provides excellent carpet and hard floor cleaning on surfaces
16. it shaft until the button locks into place fig 4 Plug the small power cord connected to the nozzle into the receptacle in the back of the unit NOTE Before using please read the important safety and operating instructions Servicing of Double Insulated Appliances A double insulated appliance is marked with one or more of the following The words Double Insulation or Double Insulated or the double insulation symbol In a double insulated appliance two systems of insulation are provided instead of grounding No grounding means is provided on a double insulated appliance nor should a means for grounding be added to the appliance Servicing a double insulated appliance requires extreme care and knowledge of the system and should be done only by qualified service personnel Replacement parts for a double insulated appliance must be identical to the parts they replace Polarization Instructions To reduce the risk of electric shock the Oreck Steemer model is equipped with a polarized alternating current line plug a plug having one blade wider than the other This plug will fit into a polarized outlet only one way This is a safety feature If you are unable to fit the plug fully into an outlet try reversing the plug If the plug should still fail to fit contact a qualified electrician to replace the obsolete outlet Do not defeat the purpose of the polarized plug in any way A L C l The Oreck St
17. om has been completed WARNING Do not push forward Pull the cleaner towards you to clean This cleaner has been specifically designed to place the nozzle deep into the carpet Push down gently on the handle to lift the nozzle out of the carpet to move forward and reposition the cleaner IMPORTANT Adjust the speed of the cleaning stroke to your carpet and flooring conditions Heavily soiled or stained carpets or floors will require slower strokes Avoid oversaturating NOTE The nozzle squeegee may be flipped for deeper cleaning on deep pile carpets See To Replace Squeegee To shorten the drying time go back over the floor pulling slowly backwards without depressing the red button Repeat this procedure until you do not see water being pulled through the nozzle To Rinse Carpet and Hard Flooring fig 12 Turn the Shampoo Rinse switch to the RINSE position fig 13 Place power switch in the ON position fig 14 To rinse carpet or hard flooring press the red button in the handle Slowly pull the cleaner backwards over already cleaned area Pressing the button releases clean water As you pull the nozzle over the sprayed floor the nozzle extracts any remaining solution from the floor and stores the dirty water in the recovery tank fig 15 To move forward slightly tilt the nozzle off the floor and roll the cleaner forward Repeat process working in small overlapping rows for even cleaning until the entire room has been
18. or workmanship This limited warranty does not apply to any part subjected to accident abuse commercial use alteration misuse damage caused by act of God the use of voltages other than indicated on the serial number displayed on this product or service of this product by other than Oreck or a participating Factory Authorized Service Center Oreck does not authorize any person or representative to assume or grant any other warranty obligation with the sale of this product Oreck s limited warranty is valid only if you retain proof of purchase from Oreck or an Oreck Authorized Retail Dealer for this product If you purchase this product from any other source your purchase is AS IS which means Oreck grants you no warranty and that you not Oreck assume the entire risk of the quality and performance of this product including the entire cost of any necessary servicing or repairs of any defects Oreck s liability for damages to you for any costs whatsoever arising out of this statement of limited warranty shall be limited to the amount paid for this product at the time of original purchase and Oreck shall not be liable for any direct indirect consequential or incidental damages arising out of the use or inability to use this product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PR
19. ove loose dirt vacuum upholstery thoroughly with a vacuum cleaner If the upholstery is being cleaned for the first time CHECK FOR COLORFASTNESS Test a small area several hours before starting to clean upholstery Pour a small amount of Steemer Full Release Professional Upholstery Shampoo on a clean white cloth and blot upholstery Examine the cloth for color removal If color appears on cloth the upholstery is not colorfast and should not be cleaned with wet extraction methods Let test area dry completely Inspect for changes in color bleeding stretching or shrinkage Test another area if in doubt This product is not recommended for use on silk velvet wool and some cotton blends To Clean Upholstery amp Small Spill Pick Ups Plug cord into an electrical outlet fig 5 Test and reset A L C l on the plug fig 11 Insert a specially formulated Steemer Full Release Professional Upholstery Cleaner Cartridge fig 13 Turn cleaner on by placing the On Off power switch in the ON position fig 14 Lock the cleaner button by pressing and sliding the button forward on the main handle fig 18 Depress the red dispensing trigger on the hand held nozzle and slowly drag the nozzle towards you Make a second pass at right angles to the first This will minimize any streaking or uneven appearance Several key precautions must be followed to insure operator safety 1 Always test and reset the Steemer A L C l plug 2 Do not
20. ppliance require warranty service in the U S A present this slip to the Authorized Service Center as your proof of purchase date or in Canada call customer service Polarized Plug Notice This product is equipped with a polarized alternating current line plug a plug having one blade wider than the other This plug will fit into the power outlet only one way This is a safety feature If you are unable to insert the plug fully into the outlet try reversing the plug If the plug should still fail to fit contact an electrician to replace the obsolete outlet Do not defeat the purpose of the polarized plug Accessories Call your authorized ORECK Home Care Center your authorized dealer or call the Home Care Hotline toll free at 1 800 989 3535 ITEM PART Oreck Steemer Full Release Professional FRSS131 Spot amp Stain PreCleaner Oreck Steemer Full Release Professional 40032 03 Carpet amp Hard Floor Cleaner Oreck Steemer Full Release Professional 40033 03 Upholstery Cleaner Steemer Value 6 Pack FRC132 5 Carpet amp Hard Floor Cleaners 1 Spot amp Stain PreCleaner Oreck Steemer Belts 2 Pack OR114 Squeegee Replacement 53311 01 0384 IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance basic precautions should always be followed including the following READ ALL INSTRUCTIONS BEFORE USING THIS STEEMER CLEANER WARNING To reduce the risk of fire electric shock or injury Do not lea
21. ve appliance unattended when plugged in Unplug from outlet when not in use and before servicing Use indoors only Do not immerse motorized nozzle use only on carpet moistened by cleaning process Do not allow to be used as a toy Do not allow infants or children around the machine during operation Use only as described in this manual Use only manufacturer s recommended attachments Do not use with damaged cord or plug If appliance is not working as it should has been dropped damaged left outdoors or dropped into water return it to a service center or call customer service at US 1 800 989 3535 Canada 1 888 676 7325 Do not pull or carry by cord use cord as a handle close door on cord or pull cord around sharp edges or corners Keep cord away from heated surfaces Do not run appliance over cord Do not unplug by pulling on cord To unplug grasp the plug not the cord Do not handle plug or appliance with wet hands Do not put any object into openings Do not use with any opening blocked keep free of dust lint hair and anything that may reduce air flow Keep hair loose clothing fingers and all parts of body away from openings and moving parts Do not use to pick up anything that is burning or smoking such as cigarettes matches or hot ashes Turn off all controls before unplugging Use extra care when cleaning on stairs Do not use to pick up flammable or combustible liquids such as gasoline or lighter fluid
Download Pdf Manuals
Related Search