Oreck XL2205RH User's Manual
Contents
1. Before assembling appliance remove two screws from connector assembly Remove cardboard insert by pulling upward W ith ON OFF switch facing the front of the unit slide upper handle section over matching section of the connector assembly Insert short screw into top hole and long screw into bottom hole then tighten firmly until handle is no longer loose Attach cord to cord clip by pressing cord above and below clip ensuring the cord is fully rested in clip To Replace Paper Filter Dust Bag WARNING Unplug cord from electrical outlet before servicing E BAG REMOVAL 4 1 Unsnap bag door from base 2 Gently pull bag from cardboard collar upwards 3 XL2605HH Dust seal will close automatically BAG INSTALLATION 1 Slide the cardboard collar completely onto bag dock door ENFONCEZ JUSQU ENTENDRE UN BRUIT PRESIONE HAST CHASQUIDO DE SUJECI h l 2 Firmly push bag dock door with both thumbs on indication point until it snaps Operating Instructions To Operate Make sure the disposable paper filter dust bag is in place DO NOT operate the cleaner without a paper filter dust bag Plug the power cord into an electrical outlet Press the ON I O FF O switch on handle assembly when ready to operate General Information The performance of your new cleaner greatly depends upon care and maintenance The instructions in this manual will guide you in perfor2. ORECK XL USER S GUIDE XL2605HH XL2205RH HIGH SPEED UPRIGHT VACUUM CLEANER WITH cre ove CLEANING SYSTEM IMPORTART SAVE THIS BOOKLET Includes e Safety Warnings e Warranty e Operating Instructions e Trouble Diagnosis e Accessories BEFORE OPERATING CLEANER READ ALL INSTRUCTIONS IN THIS MANUAL CAREFULLY Table of Contents Plug Fitting Instructions Important Safety Instructions page 2 Maintenance and Customer Service Warranty Accessories page 3 Assembly To Replace Paper Filter DustBag page 4 O perating Instructions page 5 How to Replace a Worn Belt To Adjust or Replace Brush page 6 Stuffing or Blockage Using an Oreck Fresh Air Tab page 7 Troubleshooting Guide page 8 Important Where Necessary for Plug to be Fitted The wires in this mains lead are coloured in accordance with the following code Blue Neutral Brown Live As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug proceed as follows The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or coloured Black The wire which is coloured Brown FUSE must be connected to the terminal pera which is marked with the letter L Ar TE or coloured Red ill N either
3. outer bag of your vacuum cleaner is high filtration medical material designed to filter the smallest of dust particles Itis important the inside of the outer bag be cleaned Vacuum the inside of the outer bag or hand wash turned inside out with warm water and air dry For best results the CELOC SMMS outer bag should be replaced once a year The CELOC layered disposable inner dust bag must be replaced once a month even if it is not full Change it more often if it is used in extremely dirty areas Increase the cleaning power of your vacuum by changing the bag often How to Replace a Worn Belt D WARNING Unplug cord from electrical outlet before servicing G5 Remove the replacement belt from the storage channel Remove the door by removing the hold down screw located on side of power head Slide the door forward by prying open with a screwdriver or coin Remove the belt from the brush roll pulley and the motor drive shaft Loop the new belt over the motor drive shaft Place the opposite end of the belt on the brush roll pulley Rotate the brush roll three 3 complete revolutions to ensure that no part of the belt is overhanging the end of the motor drive shaft Replace the door by sliding it into the groove at the bottom of the housing Replace the hold down screw To Adjust or Replace Brush WARNING Unplug cord from electrical outlet before servicing Rotate and ma
4. over cord The revolving brush could damage the cord 9 Use caution when vacuuming over area rug edges and fringe Disposable Paper Filter Dust Bags Disposable paper filter dust bags play a very important role in the efficiency of your O RECK vacuum cleaner The purpose of the paper bag is to trap dirt but at the same time it must be porous enough to allow air to pass through If the paper bag becomes clogged no air can pass through the cleaner and cleaning cannot take place regardless of the cleaner s power To keep your cleaner operating at maximum efficiency change the dust bag frequently DO NOT FILLABO VE THE UNE INDICATED ON THE DUST BAG Be sure the disposable paper filter dust bag is installed properly All paper dust bags are not the same Your O RECK disposable dust bags have been designed to be used with the ORECK cleaner Using bags other than genuine O RECK TYPE CC disposable bags will affect the cleaning ability of your cleaner and could cause damage to it The Belt The belt on your vacuum cleaner controls the speed of the revolving brush and is very important for the effective operation of the cleaner If the belt becomes stretched or cut it will cause the revolving brush to stop completely or slow down See instructions in the manual for replacing belt An extra belt is stored in the baseplate of your cleaner When buying replacement belts use ONLY ORECK genuine belts Belts other than ORECK belts will
5. wire is to be connected ape to the earth pin of the 3 pin plug 3 D Replace fuse with same size mue U ji POM l fuse CRD CLAM IMPORTANT SAFETY INSTRUCTIONS W hen using an electrical appliance basic precautions should always be followed including the following READ ALL INSTRUCTIONS BEFORE USING THIS VAQUUM CLEANER WARNING To reduce the risk of fire electric shock or injury Do not leave appliance unattended when plugged in Unplug from outlet when not in use and before servicing Do not use outdoors or on wet surfaces Do not operate the unit while in the upright and locked position Do not let the unit run while in any one stationary position for any period of time Keep the unit moving while in operation Do not allow to be used as a toy Close attention is necessary when used by or near children Use only as described in this manual Use only manufacturer s recommended attachments Do not use with damaged cord or plug If appliance is not working as it should has been dropped damaged left outdoors or dropped into water return it to a service center or call customer service at 0845 603 0153 Do not pull or carry by cord use cord as a handle close door on cord or pull cord around sharp edges or corners Keep cord away from heated surfaces Do notrun appliance over cord Do not unplug by pulling on cord To unplug grasp the plug not the cord Do not handle plug or appl
6. ens the blockage will be at the top of the system starting in the area where the dust bag connects to the connector assembly See illustration F F Connector Li Deflector NOTE If the Stuffing or Blockage actions do not correct the problem contact an O RECK authorized service center or call the customer service center at 0845 603 0153 IM PO RTAN T On plush and new carpets stuffing may occur due to excessive fuzz and loose cuttings in the carpet Stuffing could occur for the first few cleanings until all the loose material is removed Due to the high efficiency of the cleaner many older carpets will cause stuffing when the cleaner is first used on them Using An Oreck Fresh AirTab Your O RECK XL vacuum cleaner has a special Oreck Fresh Air tab pocket This pocket is located inside the outer bag in the area where the disposable paper bag attaches to the intake tube Insert tablet in pocket Troubleshooting Guide WARNING Unplug cord from electrical outlet before servicing Sit SERVICE CALLS CHECK THESE FIRST Is the disposable filter dust bag full Are pores of filter dust bag clogged with powder or fine dust Is anything clogging the revolving brush lower tube intake opening fan housing or connector assembly opening e isthe belt in place and turning the brush e Are the brush ends in the proper location Does the brush turn freely Are hair string or r
7. iance with wet hands Do not put any object into openings Do not use with any opening blocked keep free of dust lint hair and anything that may reduce air flow Keep hair loose clothing fingers and all parts of body away from openings and moving parts Do notuse to pick up anything thatis burning or smoking such as cigarettes matches or hot ashes Do not use without filter bag assembly in place Turn off all controls before unplugging e Use extra care when cleaning on stairs Do notuse to pick up flammable or combustible liquids such as gasoline or lighter fluid or use in areas where they may be present Do not use appliance in an enclosed space where flammable explosive or toxic vapors are given off by oil base paint paint thinner some mothproofing substances or in an area where flammable dust is present Do not pick up toxic material such as chlorine bleach drain cleaner gasoline etc with this appliance Use caution when vacuuming over area rug edges and fringe SAVE THESE INSTRUCTIONS Household Use Only Maintenance and Customer Service Your O RECK vacuum cleaner is a product of precise engineering The motor bearings are permanently lubricated and should not be oiled If you require additional information or have problems with your O RECK appliance or to order new bags or spare parts you may call O RECK customer service at 0845 603 0153 Or
8. ing steps WARNING Unplug cord from electrical outlet before servicing 1 Check for blockage at the mouth of the intake opening See illustration A If there is blockage remove o it with long nose pliers a SANITA screwdriver or coat hanger Por er If you can not reach the blockage remove baseplate See illustration B 2 If the blockage is not at the base remove lower tube See illustration C Unhook retainer spring releasing bottom of bag Twist lower collar counterclockwise to Slide up Pull tube out of base Check for blockage If blockage is in the tube remove with a coat hanger 3 If tube is not blocked look into fan housing See illus tration D Remove debris with long nose pliers a screwdriver or coat hanger 4 To reassemble check O ring on tube and replace if damaged Vacuum will not operate properly without the tube O ing Slide O ring to approximately 2 from base of tube Replace tube by first lining up slot at base of tube with inner tab inside fan housing Then reinsert tube and push down until the tube is seated Make sure O ing is in place against fan housing opening Replace and tighten collar until collar locking tabs are locked in place See illustration E Make sure collar is not cross threaded on housing 5 Many times blockage occurs due to a full dust bag causing dirt to back down the air flow system W hen that happ
9. ming basic care and maintenance To obtain the most satisfying years of service read the instructions and keep them handy for future reference Operating Recommendations This new O RECK XL High Speed Upright is one of the finest fastest and strongest units in its class You ll love the way it cleans gets under things and its SO lightweight and easy to use The following are a few simple suggestions regarding its operation 1 When inserting a new disposable paper filter dust bag FIRST PUFF OUT and OPEN THE BAG 2 When the disposable filter dust bag is full REPLACE IT 3 If at any time the machine does not pick up properly or makes an unusual noise STO P O PERATION and service 4 Although your upright will pick up pins paper clips and other small objects it is recommended that these be removed from the floor before you vacuum Failure to do so may result in permanent damage to the motor suction fan and its housing 5 WARNING Do not use your vacuum cleaner on damp or wet surfaces This will cause damage to the vacuum cleaner and is dangerous to the user Damage caused by use on wet or damp surfaces is not covered under warranty 6 REPLACE THE BELT EVERY 6 MONTHS 7 Change the disposable filter dust bag at least once a month even if it is not full The collected dustin the dust bag can cause odor attract moisture act as a breeding area and can affect the efficiency of the cleaner 8 DO NOTrun the vacuum cleaner
10. n the serial number displayed on this product or service of this product by other than Oreck or a participating Factory Authorized Service Center Oreck does not authorize any person or representative to assume or grant any other warranty obligation with the sale of this product Oreck s warranty is valid only if you retain proof of purchase from Oreck or an Oreck Authorized Retail Dealer for this product If you purchase this product from any other source your purchase is AS IS which means Oreck grants you no warranty and that you not Oreck assume the entire risk of the quality and performance of this product including the entire cost of any necessary servicing or repairs of any defects This warranty is in addition to your statutory and other legal rights Reconditioned units carry a 6 month warranty from date of purchase ACCESSORIES ITEM PART NUMBER 1 Dust Bag 8 Pack Saniseal Hypo Allergenic CCPK8DW Dust Bag 8 Pack Regular CCPK8 2 Belts 3 Pack 0300604 3 Oreck Fresh Air Tabs AIRTABS Assembly To assist you in identifying components of your vacuum the parts have been numbered as follows Handle tube upper Tube lower Power head O uter bag Paper filter dust bag Power cord Retaining spring Bag tension bar Zip fastener 10 On off switch 11 Cord hook 12 Plastic loop cable clamp 13 Connector assembly 14 Fan housing 15 Cord assembly WO OAD WI HB WN Fe
11. not operate the revolving brush correctly and may create undue stress which will cause damage to the motor and brush bearings Using belts other than ORECK belts will void the warranty Lubrication The vacuum cleaner motor bearings are factory lubricated and sealed Further lubrication is not required General Cleaner Care At least once a month check for and remove excessive lint string or hair from revolving brush Wi ipe the outside of the F cleaner with a damp cloth Y iko clean the connector deflector assembly area base of cleaner and fan housing area If there is dustin the outer bag vacuum it or shake it out A little preventative maintenance will keep your cleaner looking new and will ensure continued cleaning effectiveness CAUTION Wood Floors Soft Vinyl Asphalt Tile etc Floor Surfaces and Polished Floor Finishes Use floor and floor finish manufacturer s recommended methods of cleaning The metal strip on the base of the cleaner could be damaged if used on concrete or abrasive surfaces and therefore cause damage to wood floors soft vinyl asphalt tile etc floor surfaces and polished floor finishes The roller brush may also scuff very soft finishes Do not operate the unit while in the upright and locked position Do not let the unit run while in any one stationary position for any period of time Keep the unit moving while in operation Celoce Hypo Allergenic Filter System XL2605HH The CELOC SMMS
12. tch bearing assemblies IMPORTANT Unless the brush is worn as indicated above both bearings must be in the NEW position When rotating both bearings must be in the OLD position Unmatched settings will cause damage to your machine To determine if the brush is worn place a firm straight edge across the nozzle opening If brush bristles do not extend beyond baseplate brush should be adjusted Remove the baseplate by removing 5 screws Then remove the belt and brush roll from the housing Rotate both bearing assemblies at ends of brush roll to show OLD and replace in the holding channels in the housing N O TE The bearing assembly setting marked OLD has a smooth side The one marked N EW has notches W hen rotating bearings make sure both bearing assembly settings are the same and face up when replacing the brush roll Reassemble the belt and the baseplate and check bristle height above baseplate at each end of brush If a previous adjustment has already been made and bristle height does not extend above baseplate a new brush assembly should be ordered Stuffing or Blockage Under certain conditions it is possible to stuff or block the intake tube and the lower tube assembly If your vacuum cleaner does not pick up properly or makes unusual noise and the outer bag does not fluff up or balloon open follow the follow
13. ug fibers wound around the brush DOES NOT PICK UP Nozzle or intake pivot clogged Belt is broken or stretched Brush is worn Bag tube clogged Bag pores are clogged with fine dust Impeller fan is broken Revolving brush is not even at both ends PROBLEM POSSIBLE SOURCE AREAS TO CHECK CLEANER N ot plugged in Be sure cleaner is WILL NOT RUN properly firmly plugged into wall outlet No electricity in Check electrical wall outlet source fuse or circuit breaker CLEANER Filter bag is full Replace filter bag See To Replace Paper Filter Dust Bag Clear obstruction Replace belt See To Adjust or Replace Brush Clear obstruction Change bag Return to Service Center for repair Check brush roll end cards Make sure words OLD or NEW match at each end ALL OTHER SERVICING SHOULD BE DONE BY AN ORECK AUTHORIZED SERVICE CENTER CALL CUSTOMER SERVICE HOT LINE 0845 603 0153 W henever calling please be sure to have your model and serial number from data plate 2005 Oreck Holdings LLC All rights reserved All word marks logos product configurations and registered trademarks are owned and used under the authority of Oreck Holdings LLC Printed in America 75316 08 REV A 8 08 05 ECN R 7873
14. write to O reck UK P O Box 201 Exeter Devon EX1 1XB Attention O reck Customer Service Please specify the model number and serial code number which can be found on the data plate on the back of the vacuum Save your sales or purchase slip Should your O RECK appliance require warranty service present this slip to the Authorized Service Center as your proof of purchase date ORECK MANUFACTURING COMPANY Oreck 21180 Johnson Road Long Beach MS USA 39560 gives you the following warranty for this product only if it was originally purchased for residential use not resale from Oreck or an Oreck Authorized Retail Dealer Oreck will repair or replace free of charge to the original purchaser any part that is found to be defective in material or workmanship within three 3 years of date of purchase ten 10 years on housing This warranty applies to normal domestic use Any commercial use of this product will void this warranty This limited warranty covers the revolving roller brush for one 1 year for residential use only This warranty does not cover the replacement of expendable or consumable parts such as carbon motor brushes edge brushes belts bulbs disposable bags and other parts subject to normal wear unless they are defective in material or workmanship This warranty does not apply to any part subjected to accident abuse alteration misuse damage caused by act of God the use of voltages other than indicated o
Download Pdf Manuals
Related Search