Oracle Audio Technologies FRONTDOOR OFD-614 User's Manual
Contents
1. circuit board Note Any Intercoms that had been taught to this unit will have to have their memory cleared and be re taught to the Active Unit in the network as if they were newly installed Note Both steps 1 amp 2 must occur within 20 seconds of each other 1 To activate the Passive FrontDoor press the LEARN button inside the FrontDoor unit for a second until you hear a beep and release it 2 Press the LEARN button inside the primary FrontDoor unit for a second until you hear a beep and release it 3 You will hear a tone indicating a successful activation 4 Proceed to Section 3 Model OFD 614 5 4 2006 Patents Pending Model OFD 614 5 4 2006 Patents Pending Model OFD 614 5 4 2006 Patents Pending Model OFD 614 5 4 2006 Patents Pending Model OFD 614 5 4 2006 Patents Pending Model OFD 614 5 4 2006 Patents Pending2. see page 11 as a guide for screw placement Tighten the top two screws halfway Place the back of the Intercom on the two screws slide the unit down and tighten Put the other two screws in the bottom holes and tighten see Figure 1 Note Do not assemble the front of the unit until it has been activated B MOUNTING THE OFD WITH MOUNTING TAPE To mount the Intercom on a metal glass or other smooth surface where you wouldn t want to use screws use the double sided mounting tape Note For best results clean both surfaces that the double sided mounting tape will be in contact with using the included alcohol wipe Peel the protective paper off of the mounting tape and firmly press it onto the back of the Intercom see Figure 1 Press firmly on the back of the tape to push out any trapped air bubbles When ready to do so peel the red protective paper from the mounting tape and firmly press the intercom on to the surface that you wish to mount it on Note Do not assemble the front of the unit until it has been activated Figure 1 4 B ACTIVATING AN OFD WITH A GATE ACCESS PANEL GAP Model OFD 614 5 4 2006 Patents Pending IN kes on ul PKPA PEN LIAN U TIME Ko viwy ivuUuuly UU As A tw anything within an existing network please follow the directions found in the Oracle Wire free Repeater product manual 3 0 ASSEMBLING THE INTERCOM Put the two halves of the Intercom body together Place the two black screws i
3. One year limited WARRANTY International Electronics Inc IEI warrants this product to be free of defects in materials and workmanship for one year For a period of ONE YEAR following purchase IEI will repair or replace the product free of charge including parts labor return shipping to you and handling After the initial one year of operation the limited lifetime warranty will cover parts labor and return shipping to you with a minimal handling charge specific to the product as listed below FrontDoor Wireless Intercom 40 00 If you have installation or operation questions or are in need of warranty service please contact our Product Support department by email at techsupp nwlink com or call 360 254 1564 Tuesday Friday 7 5 Pacific Time If the issue is not resolvable a manufacturer s warranty repair order may be issued To have the product s sent for warranty service A Return Authorization number will be issued for warranty service which must be put on the outside of the package to be received and handled properly Packages for warranty service may be sent to the following address Packages with no RA may not be accepted IEI 5913C NE 127th AVE Suite 800 Vancouver WA 98682 Please include a note describing the problem that you are having and a copy of your original sales receipt within the first year If the warranty service is outside the first year please include a check made out to IEI based on the list of handling
4. able Intercom OPI and Oracle Flush Mount Intercom RIFM your intercoms form an exclusive network and respond only to other intercoms in your network patent pending When used with Oracle Telephone Interface Unit OTIU the Oracle FrontDoor OFD will ring your telephones and allow you to speak with the visitor No wiring of any kind is required Simply plug into any phone jack and receive your visitors on the phone Features Caller ID and much more PARTS SUPPLIED WITH OFD SINGLE UNIT 1 Oracle FrontDoor Unit OFD 2 Black 8 X 94 Assembly Screws 4 Silver 4 X 4 Mounting Screws 1 Piece of 3M High Strength Mounting Tape PARTS SUPPLIED WITH OFD OTIU KIT All of the parts supplied with the OFD plus 1 Oracle Telephone Interface Unit OTIU 1 Instructions for Installing the OTIU 1 Antenna 1 18V Power Adapter 1 Phone Cord 1 Set of 4 Bumper Feet PARTS SUPPLIED WITH OFD OPI KIT All of the parts supplied with the OFD plus 1 Oracle Portable Intercom OPI 1 Instructions for Installing the OPI 1 Set of 4 Bumper Feet ic te C ACTIVATING THE OFD WITH A REPEATER CON T NOTE If the Repeater Units have not been previously activated to anvthina within an avietina natwarlh nlasea fallaw tha dirartiane faiined either the included screws or the included double sided high strength tape A MOUNTING THE OFD WITH SCREWS To mount the FrontDoor use the included mounting template
5. al surface NOTE STUCCO WALLS When used in a dwelling with stucco or cement walls the RF range can be reduced greatly Place the repeater close to the house to mitigate this problem There is a Double Beep Every Ten Minutes The intercom is indicating that the batteries are low and need to be replaced How do Clear an Intercom s Memory Only when used in passive mode In active mode there is no need to erase this devices memory Hold the LEARN button down for 20 seconds A tone will indicate that the unit has cleared its memory and you can re teach it to a new intercom If an intercom signals while the buttons are depressed the procedure will have to be repeated 10 1 1 INSTALLING THE OFD Make sure that the CALL button is in easy reach of a visitor The unit may be mounted with either the included screws or the included double sided high strength tape Model OFD 614 5 4 2006 Patents Pending The Oracle FrontDoor OFD is designed for use as a Wireless Doorbell and Intercom for residential as well as commercial applications It is designed to tolerate severe outdoor conditions of 40 to 85 C as well as high humidity and condensation Since this intercom system requires no connection to wall power it is perfect for remote locations The Oracle FrontDoor OFD features an amazing 1000 range and allows multiple simultaneous conversations using a 900 MHz secure digital radio link Compatible with the Oracle Port
6. fees shown above Please note that you may need to send multiple units for warranty service testing and upgrading though only the applicable fee for handling the failed unit s will be charged Please allow 2 4 weeks for service and return shipping If an EXPEDITED repair replacement is requested a 100 surcharge applies In this case please write EXPEDITED after the RA number IEI will attempt to return expedited repair orders within one week except during holidays All repairs or replacements are at the discretion of the Manufacturer This warranty excludes items that have been abused altered incorrectly installed or repaired by an unauthorized person Changes or modifications not expressly approved by the Manufacturer could void the user s authority to operate the equipment The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment Such modifications could void the user s authority to operate the equipment This warranty is limited to the product only No consequential damages are covered This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation International Electronics Inc FCC ID JLFODI1 IC Country Of Origin USA TABLE OF CONTENTS Brig
7. h Mount Intercom hold down both buttons for 3 seconds until the channel lights start flashing quickly A 2 Press the LEARN button inside the FrontDoor unit for a second until you hear a beep and release The Flush Mount will sound a tone indicating a successful activation 3 Proceed to Section 3 5 B ACTIVATING ADDITIONAL INTERCOM UNITS BACK INTO THE NETWORK Note Both steps 1 amp 2 must occur within 15 seconds of each other 1 Press and release the LEARN button on an un activated Oracle Intercom On a Flush Mount Intercom hold down both buttons for 3 seconds until the channel lights start flashing guickly TG Note Both steps 1 amp 2 must occur within 20 seconds of each other 1 Using the phone that is connected to the OTIU once you hear a dial tone press 0 7 BEEP Hang up and the LEARN light will flash for up to 15 seconds If it does not and you hear an error tone check the OTIU manual 2 On the FrontDoor press and hold down the learn button for 1 second to put it into learn mode 3 The OTIU will ring the telephone and a Caller ID will display Unit Learned 4 Proceed to Section 3 2 2 ACTIVATING INTO AN EXISTING INTERCOM NETWORK A ACTIVATING THE OFD TO THE MAIN INTERCOM UNIT Note If the existing network contains a GAP MiniGAP or another FrontDoor see Multi FD Mode To activate a FrontDoor into an existing intercom network the memory on each of the Intercoms to be u
8. ht 3g Ideas Model OFD 614 5 4 2006 Patents Pending Oracle Thank you for purchasing the Oracle FrontDoor Unit This product has been designed and manufactured in the USA utilizing the highest guality standards FrontDoorm a Wireless Doorbell and Intercom Easy to Install Totally wireless Fully Compatible with other Oracle Intercom units Weather Resistant Design Doorbell tones for Front Door and Back Door Unlimited number of units can operate on a property without interfering with other Intercom Networks Up to 5 Year battery life Penetrates buildings with ease Range up to 1000 feet Auto channel and frequency selection Crystal Clear digitally secure connection 900 MHz Digital Radio Technology One year limited warranty Reguired NOTE This product is compatible with Oracle Portable Intercom OPI model 605 5 or later and or Oracle Telephone Interface Unit OTIU MADE IN USA International Electronics Inc Made With Pride In the USA A manufacturer s full One Year Warranty covers this product aTa 8 0 No Wiring or Trenching Preface General Information oo maan Parts SUPPE renren emlabsnka Section 1 Installation 1 1 Installing the Oracle FrontDoor OFD A Installing the OFD with screws B Installing the OFD with mounting tape 1 2 Installing the Batteries Section 2 Ac
9. n the top and bottom holes on the front of the Intercom and tighten The Intercom is ready to use 4 0 USING THE INTERCOM To talk hold down the CALL button All intercom units in your network will receive the signal When somebody responds by holding down the CALL button on a different intercom unit a secure channel is created and other units will not hear the signal making your conversation secure 9 1 2 INSTALLING THE BATTERIES Place four AA Alkaline batteries in the battery pack The batteries should last one year with average use ZZ GI BZ To set a FrontDoor unit to Passive Mode switch dipswitch 1 UP away from the circuit board 1 2 3 4 Note Any Intercoms that had been taught to this unit will have to have their memory cleared and be re taught to the Active Unit in the network as if they were newly installed Note Both steps 1 amp 2 must occur within 20 seconds of each other 1 To activate the Passive FrontDoor press the LEARN button inside the FrontDoor unit for a second until you hear a beep and release it 2 Enter the Master PIN number on the GAP For example 1 2 3 4 Then enter After the BEEP press CALL 3 You will hear a tone indicating a successful activation 4 Proceed to Section 3 C ACTIVATING THE OFD WITH A REPEATER WITHIN AN EXISTING NETWORK Note Both steps 1 amp 2 must occur within 15 seconds of each other 1 To activate the Passive Fr
10. ns to this eguipment Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the eguipment Pet ee GENERAL INFORMATION By switching dipswitch 4 UP away from the circuit board you can set the Indoor Outdoor Intercom s volume to be louder 5 2 ADJUSTING MICROPHONE SENSITIVITY To increase the Outdoor Intercom s microphone sensitivity switch dipswitch 3 UP away from the circuit board 6 0 ALTERNATE CHIMES FOR FRONTDOOR VS BACKDOOR The FrontDoor can be set to ring the inside Intercom units with two alternate chime patterns to identify which unit is signaling Switch dipswitch 2 UP away from the circuit board to set a FrontDoor unit to the alternate chime tone 7 0 TROUBLESHOOTING AND FREQUENTLY ASKED QUEST Nothing Happens The Intercom Does Not Function Make sure that the Intercom has fresh batteries in it When you press the CALL button you should hear a tone If the units have power but do not communicate they may need to form a network Press the LEARN button on each unit that needs to form a network and they will beep in response You may need to clear their memory and re teach them see How do I Clear the Intercom s Memory below The Intercom is Not Getting the Expected Transmission Range Trees metal electrical wiring or other electrical devices directly between units can limit the range as can having it mounted on a tree masonry or met
11. ontDoor press the LEARN button inside the FrontDoor unit for a second until you hear a beep and release it 2 Press the LEARN button on ONE of the Repeater Units The LED by the LEARN button will light up for several seconds and then will go out indicating a successful activation 3 Proceed to Section 3 See next page for an example of an existing network with an OFD and Repeater 8 21 ACTIVATING AN INTERCOM NETWORK CON T C ACTIVATING THE OFD WITH AN OTIU Model OFD 614 5 4 2006 Patents Pending Note If used in location that will be below 10 C 20 F Lithium batteries are recommended Dipswitch LEARN Battery Block Button Pack 21 ACTIVATING AN INTERCOM NETWORK The FrontDoor must be taught to an intercom to form an intercom network or must be taught into an existing network See Activating into an Existing Intercom Network The FrontDoor is fully compatible with other Oracle System Intercoms A ACTIVATING THE OFD WITH AN ORACLE PORTABLE Note Both steps 1 amp 2 must occur within 15 seconds of each other 1 Press and release the LEARN button on an Oracle Portable Intercom OPI 2 Press the LEARN button inside the FrontDoor unit for a second until you hear a beep and release The OPI will sound a tone indicating a successful activation 3 Proceed to Section 3 B ACTIVATING THE OFD WITH A FLUSH MOUNT Note Both steps 1 amp 2 must occur within 15 seconds of each other 1 On a Flus
12. sed needs to be cleared Note To clear the memory on an Oracle Intercom hold down the learn button for up to 20 seconds until a tone is heard Note To clear the memory on a Flush Mount Intercom hold down both buttons of the Intercom for up to 20 seconds until a tone is heard Note Both steps 1 amp 2 must occur within 20 seconds of each other 1 Press and release the LEARN button on an Oracle Intercom On a Flush Mount Intercom hold down both buttons for 3 seconds until the channel lights start flashing quickly 2 Press and release the LEARN button inside the FrontDoor unit Note Activate all other Intercoms to this Intercom NOT to the FrontDoor See example below and Step B on next page Step A Ko Model OFD 614 5 4 2006 Patents Pending channel lights start flashing quickly 2 Press and release the LEARN button on the activated Oracle Intercom or Flush Mount Unit 3 Proceed to Section 3 2 3 MULTI OFD MODE An Oracle FrontDoor OFD unit is an Active unit that takes control of the Intercom Network If you wish to have a second or multiple Oracle Frontdoor unit in the network or if using the Frontdoor with an Oracle Gate Access Panel or MiniGAP then it will have to be placed in Passive mode The Passive FrontDoor will become an accessory to the Primary FrontDoor or Gate Access Panel A ACTIVATING AN OFD WITH AN OFD To set a FrontDoor unit to Passive Mode switch dipswitch 1 UP away from the
13. tivation 2 1 Activating an Intercom Network A Activating the OFD with an Oracle Portable OPI B Activating the OFD with a Flush Mount RIFM C Activating the OFD with a Telephone Interface OTIU 2 2 Activating into an Existing Network A Activating an OFD to the Main Intercom Unit B Activating Intercom Units back into the network 2 3 Multi OFD Mode A Activating an OFD with an OFD B Activating an OFD with a Gate Access Panel C Activating an OFD with a Repeater Section 3 Assembly Assembling the InterCom cccccseeeeeeeeeeeeeeeeeeeeennens Section 4 Use Using the IE ter OOM anne ear aa emban emo adas Section 5 Adjusting Volume 5 1 Adjusting the Speaker Volume 5 2 Adjusting Microphone Sensitivity Section 6 Alternate Doorbell Chimes Alternating Chimes for FrontDoor vs BackDoor Section 7 Frequently Asked Questions Troubleshooting and FAQ S ccccceceeeceeeeeeaeeeeeeeeeeenes Section 8 Mounting Template Mounting Template come 2 5 1 ADJUSTING THE SPEAKER VOLUME Model OFD 614 5 4 2006 Patents Pending MOUNTING TEMPLATE Use this template as a guide for mounting screw placement 1 La NOTE The manufacturer is not responsible for any radio or TV interference caused by unauthorized modificatio
Download Pdf Manuals
Related Search