Optimus 120-1725 User's Manual
Contents
1. Do not connect four speakers to your car stereo amplifier unless it is designed for a four speaker connection See your stereo amplifier s owner s manual for instructions ROUTING SPEAKER WIRE Avoid routing speaker wire near moving parts or sharp edges You can usually route it along the wiring channel beneath the vehicle s door facings by carefully removing the molding that holds the carpet in place After routing the speaker wire replace the molding MOUNTING THE SPEAKERS After you have connected the speakers and turned on your autosound system to ensure that everything is working properly turn off your autosound system and mount the speakers 1 Select a flat area such as your car s rear deck for the mounting surface The surface should be sturdy enough to support the weight of the speakers 2 Use the speaker cabinet s base as a template to mark the desired mounting position Then determine the center of the mounting position Drill a hole 1 4 inch wide in the center of the mounting position Attach the bolt to the bottom of the speaker cabinet and secure the bolt using a Phillips screwdriver Position the speaker cabinet on the mounting surface by inserting the bolt through the drilled hole Underneath the mounting surface place the washer over the bolt Then thread and tighten the wing nut until the speaker cabinet is secure Three Way Bass Reflex Car Spea2. TO 250 1A FUSE STRIP BATTERY SOLDER 14 DARK BLUE Y AMP REMOTE WIRE BANDING WHITE TURN ON TUBE HEATING 500mA MAX 12 V OUTPUT May or may not be present depending on features of individual radios 2CH 4CH SWITCHABLE UNIT Pin No WIRE COLOR WIRE SPECS ABEL REMARK 1 WHT BLK AWG 20 FRONT L STRIP SOLDER 2P CORD 2 GRY BLK FRONT R 3 GRN BLK a REAR L y 4 VIO BLK py REAR R A 5 BLACK AWG 206 GROUND 6 3mm r FORK TERMINAL 6 ORG WHT DIMMER STRIP SOLDER 7 PINK WHT v PHONE MUTE 8 WHITE AWG 20 FRONT L 2p CORD y 9 GRAY y FRONT R 10 GREEN me REAR L 11 VIOLET REAR R u 12 RED AWG 20 12 V TO 250 1A FUSE amp 24M M IGNITION TRANS STRIP SOLDER 13 YELLOW FIZ VE TO 250 1A FUSE STRIP BATTERY SOLDER 14 DARK BLUE AMP REMOTE WIRE BANDING amp WHITE TURN ON TUBE HEATING 500mA MAX 12 V OUTPUT May or may not be present depending on features of individual radios 4 Chnl Unit May or may not be present depending on features of individual No WIRE COLOR WIRE SPECS A
3. BEL REMARK i WHT BLK AWG 20 FRONT L STRIP SOLDER 2P CORD 2 GRY BLK FRONT R 3 GRN BLK REAR L 4 VIO BLK REAR R 5 BLACK AWG 206 GROUND 6 3mm r FORK TERMINAL 6 ORG WHT DIMMER STRIP SOLDER 7 PINK WHT PHONE MUTE 8 WHITE AWG 20 FRONT L 2p CORD 9 GRAY FRONT R 10 GREEN REAR L 11 VIOLET REAR R n 12 RED AWG 20 12 V TO 250 1A FUSE 24M M IGNITION TRANS STRIP SOLDER 13 YELLOW 12 V TO 250 1A FUSE STRIP BATTERY SOLDER 14 DARK BLUE i AMP REMOTE WIRE BANDING amp WHITE TURN ON TUBE HEATING 500mA MAX 12 V OUTPUT FRONT 5 Pin DIN Green Right radios LN 03 04 White Right Brown Left Gray Left Red 12 V Power REAR GRN BLK Right WH BLK Right BR BLK eft GRAY BLK eft Orange SD Lo Black Ground Red w Memory White Backup
4. Three Way Bass Reflex Car Speaker System 120 1725 Features Faxback Doc 38063 Your Optimus Three Way Bass Reflex Car Speaker System is designed to give you clean sound with powerful bass The system is ideal for rear deck mounting To get the best sound from your speakers please read all of these instructions carefully for the proper wiring and mounting procedures BEFORE YOU BEGIN We recommend that you connect your autosound system to the speakers befor you mount them so you can test the speakers and the wire connections When you verify that everything works properly turn off your autosound system and mount the speakers NOTE If you are unsure about the following installation process we recommend that you have a professional install the speakers Three Way Bass Reflex Car Speaker System 120 1725 Wiring the Speakers Faxback Doc 38064 Connect two speakers to your auto sound system as shown NOTES If your autosound system has a front to rear fader follow the instructions in the audio component s manual for the correct speaker connections To ensure proper phasing match the speaker wires to the corresponding red or black speaker terminals Improper phasing can cause poor bass response CAUTIONS Do not connect any of your speaker wires to chassis ground Use all four wires to connect the speakers to your vehicle s autosound system
5. ker System 120 1725 Specifications Faxback Doc 15674 Crossover Capacitor DLL Peis eis kw See AAA A AA eee sie w ee AAA 5x11 mm Capacitance ai a hl bles oa Ae ee 8 oe 2 2 micro Farad 50 V B P Speaker Sizes es gests edd A debe ante a eee e 3 1 2 inch woofer 2 inch midrange 1 1 2 inch tweeter Barium Magnet Weight ies in e Sys e cong AS A Ra 5 30 OZ Power Handling Capacity eii sa Brae ate Sige Bea a A A 30 Watts each Impedance anar o E A care de dh amen ia A nta 4 ohms EXEQUENEY Responses A it A A A ete Eee AD 150 20 000 Hz SOT SC Vase te A A A A E Wa eto ie des fa ge Nee id 90 dB Specifications are typical individual units may vary Specifications are subject to change without notice br km 02 19 1997 Audio Connection Information 120 Series Plug Male 2 Ch System Faxback Doc 19994 Pin No WIRE COLOR WIRE SPECS LABEL REMARK 1 WHT BLK AWG 20 FRONT L STRIP SOLDER 2P CORD 2 GRY BLK K FRONT R m 3 4 5 BLACK AWG 206 GROUND 6 3mm r FORK TERMINAL 6 ORG WHT v DIMMER STRIP SOLDER 7 PINK WHT v PHONE MUTE N 8 WHITE AWG 20 FRONT L 2p CORD n 9 GRAY N FRONT R v 10 11 12 RED AWG 20 12 V TO 250 1A FUSE amp 24M M IGNITION TRANS STRIP SOLDER 13 YELLOW s 12 V
Download Pdf Manuals
Related Search