Onkyo TX-NR737 Owner's Manual
Contents
1.2. e Output to multi zone is not possible if the connection is only with HDMI cable or digital cable e Analog audio output setting may be necessary on the player Step 3 m Connecting speakers in another room It is possible to directly connect the speakers in another room without an amplifier Connect the speakers in another room to the SPEAKERS ZONE2 terminals of the unit using speaker cables Note that 5 2 ch will be the maximum in the main room during Zone 2 playback Sound cannot be output from the Surround Back speakers and Height speakers zk In this case the Dolby Atmos listening mode cannot be selected Change the setting After connecting the speakers press RCV and then HOME on the remote controller select Setup 2 Speaker Setup Speaker Settings and set Powered Zone2 to Yes e Adjust the volume on this unit To adjust the volume press ZONE2 on the remote controller and adjust with VOLA Y To control on the main unit press ZONE2 and within 8 seconds adjust with the MASTER VOLUME control You can mute the sound by pressing MUTING on the remote controller Performing multi zone playback 1 Press ZONE2 or ZONES on the remote controller point the remote controller at the unit and press ORECEIVER Z2 or Z3 lights on the main unit display and the multi zone function is enabled ZONE 2 or ZONE 3 is now on 2 Press ZONE2 or ZONES on the remote controller again and pre
3. 1 a While holding down CBL SAT 2 Press OON STANDBY How to reset the remote controller 1 While holding down RCV on the remote controller press HOME until the remote indicator lights about 3 seconds 2 Within 30 seconds press RCV again Remote indicator RCV Specifications Amplifier Section Rated Output Power All channels 110 watts minimum continuous power per channel 8 ohm loads 2 channels driven from 20 Hz to 20 kHz with a maximum total harmonic distortion of 0 08 FTC 125 watts minimum continuous power per channel 6 ohm loads 2 channels driven at 1 kHz with a maximum total harmonic distortion of 0 7 FTC North American 7 ch x 170 W at 6 ohms 1 kHz 1 ch driven of 1 IEC Others Maximum Effective Output Power 7 ch x 185 W at 6 ohms 1 kHz 1 ch driven JEITA Asian Dynamic Power gt 1EC60268 Short term maximum output power 250 W 3 Q Front 220 W 4 Q Front 130 W 8 Q Front THD N Total Harmonic Distortion Noise 0 08 20 Hz 20 kHz half power Damping Factor 60 Front 1 kHz 8 Q Input Sensitivity and Impedance Unbalance 200 mV 47 kQ LINE 2 5 mV 47 kQ PHONO MM Rated RCA Output Level and Impedance 200 mV 2 2 kQ LINE OUT Maximum RCA Output Level and Impedance 2 V 2 2 KQ LINE OUT Phono Overload 70 mV MM 1 kHz 0 5 Direct Frequency Response 5 Hz 100 kHz 1 dB 3 dB Direct mode Tone Control Characteristics 10 dB 20 Hz BASS
4. When using commercially available banana plugs Tighten the speaker terminals to the end and then insert the banana plugs Do not insert the core of speaker cable directly into the hole for banana plug of speaker terminal North American models Step 1 Height speakers arrangements Dolby Laboratories recommends to place the speakers as described on Installing speakers in ceiling to obtain the best Dolby Atmos effect Installing speakers in ceiling lt gt dies O Top Front Top Middle Ceiling speakers etc are used for maximizing effects in Dolby Atmos or Dolby Surround listening mode Install Top Front speakers midway between the position just above the listening position and the position just above the front speakers Install Top Middle speakers just above the listening position You can select bi or on the unit For connection with the unit use the SPEAKERS BACK or HEIGHT terminals Using Dolby Enabled Speakers al On zu IB eS Dolby Enabled Speaker Front Dolby Enabled Speaker Surround A Dolby Enabled Speaker is specially designed to be used as a Height speaker There are two types of Dolby Enabled Speakers the one is to be placed on the top board of other speakers such as front speakers and surround speakers and the other is integrated typ
5. Enter the password gt on the keyboard screen select OK with the cursor buttons and press ENTER Select Shift and press ENTER to toggle between upper and lower case Select or and press ENTER to move the cursor to the selected direction Select Back Space and press ENTER to delete the character at the left of the cursor position To select whether to mask the password with gt or display it in plain text press D on the remote control Press 10 on the remote controller to enable the Shift function and CLR to delete all the input characters If the security method of the access point to be connected is WEP select Default Key ID select OK and press ENTER Push Button Use the automatic setting button of the access point to establish connection Select Push Button with the cursor buttons and press ENTER Hold down the automatic setting button of the access point for the necessary seconds select OK with the cursor buttons and press ENTER PIN code Select this method when the automatic setting button of the access point is beyond the reach Select PIN code with the cursor buttons and press ENTER to display Step 2 the 8 digit PIN code Register the displayed PIN code to the access point select OK with the cursor buttons and press ENTER For how to register the PIN code to the access point refer to its instruction manual 3 Establish connection The connection process starts an
6. Remote control sensor Receives signals from the remote controller Display LISTENING MODE buttons Allows you to select the listening mode DIMMER button North American and Taiwanese models Switches the brightness of the display RT PTY TP button European Australian and Asian models Can be used when receiving the station transmitting text information MEMORY button Registers or deletes a station TUNING MODE button Switches the tuning mode dt DISPLAY button Switches the information on the display HOME button Displays the HOME menu 3 Cursor buttons YTUNINGA button PRESET gt button and ENTER button Moves the cursor and confirms the selection When listening to AM FM broadcasting tune in to the station with YTUNINGA or select the registered station with PRESET RETURN button Returns the display to the previous state MASTER VOLUME Allows you to adjust the volume MUSIC OPTIMIZER button and indicator North American and Taiwanese models Turns on off the MUSIC OPTIMIZER function that improves the quality of the compressed audio PURE AUDIO button and indicator European Australian and Asian models Switches to the Pure Audio listening mode The indicator lights when Pure Audio listening mode is set M PHONES jack Stereo headphones with a standard plug are connected AUX INPUT HDMI MHL jacks An HD video camera or MHL enabled mobile device is connected It is possible to send video and
7. gt When you upconvert video signals input to the COMPONENT VIDEO IN jacks and output them from the HDMI OUT jack set the output resolution of the player to 480i or 576i If the input has 480p 576p or higher resolution a message prompting you to change the resolution setting will appear If your player does not support 480i or 576i output use the composite video jack zk If multiple video signal inputs are put into one input system the output will be made in the order of HDMI COMPONENT VIDEO and composite video 2 Connecting speakers Speaker layout To enjoy the Dolby Atmos listening mode Surround back speakers or Height speakers need to be installed The example above uses front Height speakers As other types of Height speakers are also applicable see the next page for details Front speakers Center speakers OO Surround speakers O Subwoofer Surround back speakers Height speakers 5 1 ch 000000 e 7 1ch 000000 D0 or 000000 090 D and QW share the same speaker terminals Select either of the groups e To use the multi zone function see the section 6 Using the multi zone function of Step 3 Playing Back Step 1 Co DO Surround back R 2 1 Surround back L Height R Front R Front L Height L mes e If there is only one Center D surround back e speaker connect S it to the BACK or O HEIGHT L termin
8. s documentation and dealer In some countries there may be restrictions on using Bluetooth devices Check with your local authorities Dat Mobile High Definition Link MHL the MHL Logo and Mobile High Definition Link are trademarks or registered trademarks of MHL LLC in the United States and other counties InstaPrevue and the InstaPrevue logo are trademarks or registered trademarks of Silicon Image Inc in the United States and other countries Apple iPod and iPhone are trademarks of Apple Inc registered in the U S and other countries Apple TV is a trademark of Apple Inc registered in the U S and other countries Siriusxm INTERNET RADIO SIRIUS XM and all related marks and logos are trademarks of Sirius XM Radio Inc and its subsidiaries All rights reserved DLNA the DLNA Logo and DLNA CERTIFIED are trademarks service marks or certification marks of the Digital Living Network Alliance This product is protected by certain intellectual property rights of Microsoft Use or distribution of such technology outside of this product is prohibited without a license from Microsoft Windows and the Windows logo are trademarks of the Microsoft group of companies QR Code is a registered trademark of DENSO WAVE INCORPORATED Safari is a trademark or registered trademark of Apple Computer Inc in the United States and other countries x v Color is a trademark of Sony Corporation MPEG Layer 3 audio co
9. 10 dB 20 kHz TREBLE Signal to Noise Ratio 106 dB LINE IHF A 80 dB PHONO MM IHF A Speaker Impedance 4Q 162 Video Section Input Sensitivity Output Level and Impedance 1 Vp p 75 Q Component Y 0 7 Vp p 75 Q Component P Cz Pp Ca 1 Vp p 75 Q Composite Component Video Frequency Response 5 Hz 100 MHz 0 dB 3 dB Tuner Section FM Tuning Frequency Range 87 5 MHz 107 9 MHz North American and Taiwanese 87 5 MHz 108 0 MHz RDS Others AM Tuning Frequency Range 522 530 kHz 1611 1710 kHz Preset Channel 40 Network Section Ethernet LAN 10BASE T 100BASE TX Wireless LAN IEEE 802 11 b g n standard Wi Fi standard 2 4 GHz band 1 11 ch North American 10 11 ch Spain 10 13 ch France 1 13 ch Others Wi Fi standard Bluetooth Section Communication system Bluetooth Specification version 2 1 EDR Enhanced Data Rate Maximum communication range Line of sight approx 15 m gt k Frequency band 2 4 GHz band 2 4000 GHz 2 4835 GHz Modulation method FHSS Freq Hopping Spread Spectrum Compatible Bluetooth profiles A2DP 1 2 Advanced Audio Distribution Profile AVRCP 1 3 Audio Video Remote Control Profile Supported Codecs SBC Transmission range A2DP 20 Hz 20 000 Hz Sampling frequency 44 1 kHz The actual range will vary depending on factors such as obstacles between devices magnetic fields around a microwave oven static electricity cordless phone reception sensi
10. MHL enabled mobile device by connecting the MHL enabled mobile device to the AUX INPUT HDMI MHL jacks on the front panel Connecting Components without HDMI If your AV component does not have HDMI jack use an available jack of your component for cable connection with this unit Just as the HDMI jacks other jacks on this unit have a preassigned input selector button on the front panel See the name of the input selector button shown with the jack when connecting the device EI EEA TASSIGNASLE Em Audio signal connection Digital connection Use a digital optical cable OPTICAL or digital coaxial cable COAXIAL for connection with a player Digital optical cable OPTICAL zk As the digital in optical jack of the unit has a cover push in the cable against the cover as it is turned inside CH Digital coaxial cable COAXIAL e Analog connection Use an analog audio cable for connection with a player To enjoy multi zone playback of audio of a CD player or such other player without HDMI output jack you need to use the RCA cable to connect the corresponding jacks of the player and this unit For details on the multi zone function see the section 6 Using the multi zone function of Step 3 Playing Back A Analog audio RCA cable Connection with turntable If it uses an MM type cartridge and does not have a built in audio equalizer connect it to
11. Management is set to Off Music Optimizer Improve the quality of the compressed audio Playback sound of lossy compressed files such as MP3 will be improved The setting can be separately set to each input The setting is effective in the signals of 48 kHz or less The setting is not effective in the bitstream signals It cannot be set if the listening mode is Pure Audio European Australian and Asian models or Direct Re EQ Re EQ THX Adjust the soundtrack that was processed to enhance its high pitch range in order to make it suitable for home theater e In Re EQ the following listening modes can be used Dolby Digital Dolby Digital Plus Dolby TrueHD Multichannel DTS DTS ES DTS Neo 6 Cinema DTS 96 24 DTS Neo 6 DTS HD High Resolution Audio DTS HD Master Audio and DTS Express e In Re EQ THX the following listening modes can be used THX Cinema THX Surround EX and THX Select2 Cinema Step 3 E Video Monitor Out The video input signals input to the unit will be converted by the unit when they are output from the HDMI OUT jack to the TV so that their resolution can match that of the TV used Select the HDMI OUT jack to be used for output Wide Mode You can set the aspect ratio Picture Mode You can adjust the image quality Cinema will automatically adjust the image to be suitable to watch movie and Game suitable to play game In Standard the resolution will be changed but the image quality
12. Setup 2 Select the item with the cursor buttons of the remote controller and press ENTER to confirm your selection To return to the previous screen press RETURN To return to the HOME menu press HOME E Sleep Timer Select to turn the unit into standby mode automatically when the specified time elapses E InstaPrevue Select to preview videos input from the HDMI input jacks collectively in a single screen The screen has a main window current input video and sub windows other input videos To switch the current input select the desired sub window with the cursor buttons and press ENTER e A black sub window is shown for the input with no video signals e InstaPrevue cannot be selected if the video is being input from HDMI IN 5 or 6 or there is no signal from the main window Depending on video signals the picture may not be properly rendered on the preview thumbnails Step 3 e 1080p or higher resolution is not supported m Setup You can change the assignment of input terminals and input selector buttons and also make various speaker settings and other advanced settings m Network Service Select to use Internet radio services and the DLNA function When you connect the unit to the network and press ENTER the network service screen will be displayed on the TV On the TV screen select the desired service or music file with the cursors of the remote controller and press ENTER to confirm and start
13. Zone 3 again press ZONE2 or ZONES to enter the Zone control mode WHOLE HOUSE MODE If you press ZONE2 and ZONES Simultaneously while playback is being performed in the main room the WHOLE HOUSE MODE is turned on Z2 and Z3 on the display light at the same time and the playback sources of all the rooms are switched to the same source at once e WHOLE HOUSE MODE is effective only for playback of the external player connected to the analog audio input jacks This function cannot be used if headphones are connected or audio is output from the speakers of the TV Step 3 MASTER VOLUME OON STANDBY Wi Fi 0 BLUETOOTH LISTENING MODE Music r CLEAR MEMORY TUNINGMODE DISPLAY GAME DIMMER MUSIC OPTIMIZER Z F PHONES AUX INPUT d j HDMI MHL E E PURE AUDIO European Australian E and Asian models J Front Panel RT PTY TP European Austral and Asian models WD HYBRID STANDBY ke SETUP MIC E ian La E OON STANDBY button Turns the unit on or into standby mode BLUETOOTH indicator Flashes while pairing with a Bluetooth enabled device is in progress and stays lit when pairing is completed Wi Fi indicator Lights when the unit is connected to the wireless LAN router ZONE 2 button and ZONE 3 button Controls the multi zone function
14. hin uetele ja nimetatud direktiivist tulenevatele teistele asjakohastele s tetele ME THN MAPOYZA O KATAZKEYAZTHE Onkyo Corporation AHAQNEI OTI TX NR737 ZYMMOPOQNETAI NPO TIZ OYZIQAEI ANAITHZEIZ KAI TIZ AOINES ZXETIKE AIATA EIZ TH2 OAHTIAZ 1999 5 EK Por la presente Onkyo Corporation declara que este TX NR737 cumple con los requisitos esenciales y otras exigencias relevantes de la Directiva 1999 5 EC Par la pr sente Onkyo Corporation d clare que l appareil TX NR737 est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999 5 CE Con la presente Onkyo Corporation dichiara che questo TX NR737 conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999 5 CE Ar o Onkyo Corporation deklar ka TX NR737 atbilst Direkt vas 1999 5 EK b tiskaj m pras b m un citiem ar to saist tajiem noteikumiem iuo Onkyo Corporation deklaruoja kad is TX NR737 atitinka esminius reikalavimus ir kitas 1999 5 EB Direktyvos nuostatas A Onkyo Corporation ezzennel kijelenti hogy a TX NR737 t pus beren dez s teljes ti az alapvet k vetelm nyeket s m s 1999 5 EK ir nyelvben meghat rozott vonatkoz rendelkez seket Hierbij verklaart Onkyo Corporation dat het toestel TX NR737 in overeenstemming is met de essenti le eisen en de andere relevante bepalingen van richtlijn 1999 5 EG Niniejszym Onkyo Corporation deklaruje e TX NR737 jest zgodny
15. or music file with the cursors of the remote controller and press ENTER to confirm and start playback e USB becomes selectable after the USB function starts up even if it cannot be selected first It may take about a minute to start up E Using Quick Setup menu In the Quick Setup menu you can set frequently used functions including input selection and volume adjustment 1 Press Q SETUP on the remote controller The Quick Setup menu is displayed on the connected TV s screen Input BD DVD Audio CBLISAT Video STB DVR Information GAME Listening Mode PC AUX 2 Select the item with the cursor buttons of the remote controller and press ENTER to confirm your selection To return to the previous screen press RETURN E Input Select the input and check the assignment of input selector buttons m Audio You can perform various audio settings including audio quality and speaker level adjustment e You cannot select this item when audio is output from the TV s speakers AN Sync If the video is behind the audio you can delay the audio to offset the gap Different settings can be set for each input e It cannot be set if the input is NET USB or BLUETOOTH e It cannot be set if the listening mode is Pure Audio European Australian and Asian models or Direct Bass Treble Adjust volume of the front speaker e It cannot be set if the listening mode is Pure Audio European Australian
16. placed while playing Internet radio in a separate room It is also possible to perform playback only in a separate room e As for analog audio input it is possible to play the same source or different sources in the main room and separate room As for the NET USB and BLUETOOTH you cannot select different inputs for the main room and separate room For example if NET has been selected in the main room and then USB is selected as playback source in the separate room the input in the main room will change to USB accordingly When listening to AM FM broadcasting you cannot select different stations for the main room and separate room Therefore broadcasting of the same station will be heard in the both rooms m Connecting an Integrated Amplifier in a Separate Room You can enjoy 2 channel stereo playback in the other room during playing 7 2 channel in the main room Connect the LINE OUT ZONE2 jacks or LINE OUT ZONE3 jacks of the unit and the line in jacks of the pre main amplifier in a separate room with an analog audio RCA Connecting with Player To output audio of the Blu ray Disc player or such other player as the source of multi zone playback it is necessary to connect the RCA audio output jacks of the player and the Zone 2 Zone 3 analog audio input jacks of the unit using the analog audio cable e The volume should be adjusted with the pre main amplifier used in the separate room
17. playback Internet radio service You can listen to Tuneln or such other Internet radio stations registered in advance DLNA You can play music files stored in the PC or NAS device connected to the network Select the server with the cursors select the desired music file and press ENTER to start playback Home Media You can play music files in a shared folder on the PC or NAS device connected to the network Select the server with the cursors select the desired music file and press ENTER to start playback Network Service becomes selectable after the network starts up even if it cannot be selected first It may take about a minute to start up e When Network Service is selected for the first time the DISCLAIMER screen will appear on the TV Select Agree if you agree the content If you do not agree the content you cannot use the network service You cannot use the Network Service function unless the TV is connected via HDMI since selecting Agree in the DISCLAIMER screen is not possible Layout of the icons in the Network Service top menu can be changed Press NET on the remote controller and press D Select the source icon with the cursors and press ENTER and then select the destination icon and press ENTER The positions of the icons are switched each other m USB Select USB in the TV screen and connect a USB storage device to the USB port on the front panel On the TV screen select the desired folder
18. the PHONO jack If the connected turntable has a built in audio equalizer connect it to the TV CD jack If it uses an MC type cartridge install an audio equalizer compatible with MC type cartridge between the unit and the turntable by connecting it to the TV CD jack For details refer to the turntable s instruction manual If the turntable has a ground wire connect it to the GND terminal of this unit If connecting the ground wire increases noise disconnect it E Video signal connection The unit has a video upconversion function For details see the next section Use a component video cable to connect a TV with component video input jacks and a player with component video output jacks KR Component video cable Its transmitted video has higher quality than that of composite video cable Step 1 Use a composite video cable to connect a TV with composite video input jack or a player with composite video output jack Um Composite video cable Video signals input to the composite video input jack or the COMPONENT VIDEO IN jacks will be upconverted to HDMI signals and then output from the HDMI output jack Note that it is not possible to convert digital audio input signals to analog or vice versa HDMI HDMI SES OS oS gt COMPONENT VIDEO v4 se gt Q Q VIDEO AV Receiver
19. this device Any question or request for service relating to the information content or services should be made directly to the appropriate content owners and services providers Precautions For European Models Declaration of Conformity We declare under our sole responsibility that this product complies with the standards Safety Limits and methods of measurement of radio disturbance characteristics Limits for harmonic current emissions Limitation of voltage changes voltage fluctuations and flicker RoHS Directive 2011 65 EU Hereby Onkyo Corporation declares that this TX NR737 is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC C nacronuero Onkyo Corporation aexnapupa 4e TX NR737 e B CbOTBETCTBUE CLC CbLIIECTBEHUTe NZSNCKBAHMA N ApyruTenpunoKuMn pasnopen6u Ha Jupektusa 1999 5 EC Onkyo Corporation t mto prohla uje ze TX NR737 spl uje z kladn po adavky a v echna p slu n ustanoveni Sm rnice 1999 5 ES Undertegnede Onkyo Corporation erkl rer herved at f lgende udstyr TX NR737 overholder de v sentlige krav og vrige relevante krav i direktiv 1999 5 EF Hiermit erkl rt Onkyo Corporation dass sich das Ger t TX NR737 in bereinstimmung mit den grundlegenden Anforderungen und den brigen einschl gigen Bestimmungen der Richtlinie 1999 5 EG befindet K esolevaga kinnitab Onkyo Corporation seadme TX NR737 vastavust direktiivi 1999 5 E p
20. txnr737upg adv en html Features Equipped with 7 channel amplifier Supports playback in Dolby Atmos format which provides 360 degree placement and movement of sounds including overhead sound Dolby Surround listening mode expands 2 ch 5 1 ch or 7 1 ch source to available speaker configurations THX Select2 Plus certified Incorporates Qdeo technology for HDMI video upscaling Equipped with 4K 60 Hz Passthrough compatible HDMI IN OUT jacks IN1 to IN4 of HDMI IN jacks are 4K compatible Supports the HDMI Through function which allows transmission from playback devices to the TV in standby state Supports HDCP2 2 a strict copy protection for providing high quality content HDMI IN3 HDMI OUT MAIN only Supports ARC Audio Return Channel e Supports USB storage playback Supports variety of network functions such as Internet Radio DLNA etc Supports Wi Fi Bluetooth and MHL enabled mobile device Bi Amping capability A V Sync Control Function to correct deviation of audio and video Multi zone function which allows you to play a different source in another room from the main room 32 bit DSP Digital Signal Processor with excellent calculation performance Music Optimizer for Compressed Digital Music files Phase Matching Bass System Automatic speaker setup available using supplied calibrated microphone AccuEQ Room Calibration Supports playback of MP3 WMA WMA Lossless FLAC WAV Ogg Vorbis Apple Lossless DSD D
21. Bldg 2 2 22 Kitahama Chuo ku OSAKA 541 0041 JAPAN http www onkyo com The Americas Onkyo U S A Corporation 18 Park Way Upper Saddle River N J 07458 U S A For Dealer Service Order and all other Business Inquiries Tel 201 785 2600 Fax 201 785 2650 http www us onkyo com For Product Support Team Only 1 800 229 1687 Europe Onkyo Europe Electronics GmbH Liegnitzerstrasse 6 82194 Groebenzell GERMANY Tel 49 8142 4401 0 Fax 49 8142 4208 213 http www eu onkyo com Onkyo Europe Electronics GmbH UK Branch Meridien House Ground floor 69 71 Clarendon Road Watford Hertfordshire WD17 1DS United Kingdom Tel 44 0 8712 00 19 96 Fax 44 0 8712 00 19 95 China Onkyo China Limited Hong Kong Unit 1033 10 F Star House No 3 Salisbury Road Tsim Sha Tsui Kowloon Hong Kong Tel 852 2429 3118 Fax 852 2428 9039 http www hk onkyo com Onkyo China PRC Mainland 1301 555 Tower No 555 West NanJing Road Jing an District Shanghai China 200041 Tel 86 21 52131366 Fax 86 21 52130396 http www cn onkyo com Asia Oceania Middle East Africa Please contact an Onkyo distributor referring to Onkyo SUPPORT site http www intl onkyo com support The above mentioned information is subject to change without prior notice Visit the Onkyo web site for the latest update SN 29401929 C Copyright 2014 Onkyo Corporation Japan All rights reserved N A D1409 0 2 9401929
22. ES AVAILABLE THROUGH THIS DEVICE ARE PROVIDED AS IS COMPANY DOES NOT WARRANT INFORMATION CONTENT OR SERVICES SO PROVIDED EITHER EXPRESSLY OR IMPLIEDLY FOR ANY PURPOSE COMPANY EXPRESSLY DISCLAIMS ANY WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO WARRANTIES OF TITLE NON INFRINGEMENT MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE Company makes no representation or warranty of any kind express or implied about the completeness accuracy validity legality reliability suitability or availability with respect to the information content or services available through this device Company shall not be liable whether in contract or tort including negligence and strict liability for any direct indirect special incidental or consequential damages or any other damages arising out of or in connection with any information contained in or as a result of the use of any content or service by you or any third party even if Company has been advised of the possibility of such damages nor shall Company be liable for any third party claims against users of this device or any third party In no event shall Company be responsible nor liable for without limiting the generality of the foregoing any interruption or suspension of any information content or service available through this device Company is neither responsible nor liable for customer service related to the information content and services available through
23. ETOOTH AM or FM Multi zone playback is not possible if the player and the unit are connected via HDMI cable or digital cable Connect the RCA audio output jacks of the player and the analog audio input jacks of the unit with analog audio cable Also analog audio output setting may be necessary on the player Cannot access to network e Try plugging unplugging the unit or the wireless LAN router or check their power on status This will work well in many cases e If the desired wireless LAN router is not in the access point list it may be set to hide SSID or the ANY connection may be off Change the setting and try again Cannot connect Bluetooth e Try plugging unplugging the unit and the Bluetooth enabled player After that check that the Bluetooth function is enabled on the Bluetooth enabled device and the connection with the unit has been established m Resetting the unit Resetting the unit to the status at the time of shipment may solve the problem If the measures above do not solve the problem reset the unit with the following procedure If you reset the unit status your preferences will be reset to the defaults Note them down before starting reset How to reset 1 While holding down CBL SAT on the main unit note that step 2 must be performed with this button pressed down 2 Press OON STANDBY on the main unit Clear appears on the display and the unit returns to standby
24. ONKYO TIX NR7 37 AV RECEIVER Basic Manual E Advanced Manual found here L w D H D http www onkyo com manual txnr737upg adv en html Enl Before Start About the Basic Manual The Basic Manual leads you through the fundamental steps to enjoy the AV Receiver from connections to TV speaker system and playback components to necessary functions for playback As well as that Basic Manual informs you with the instructions on frequently used functions Besides there is another part of the manual called Advanced Manual to inform you with more detailed information which we have decided to publish on the web from the ecological point of view Advanced Manual Advanced Manual is always updated with the latest information and its user friendly interface which does not matter whether you access from PC or Smartphone helps you to understand more deeply about the AV Receiver Advanced Manual is consisted of the following chapters e AM FM Radio Receiving Function Playing Music Files on a USB Storage Device Listening to Internet Radio Playing Music with DLNA Playing Music Files in a Shared Folder Operating Music Files with the Remote Controller Listening Mode Advanced Settings Operating Other Components with the Remote Controller Advanced speaker connections Connecting and Operating Onkyo RI Components Firmware Update Troubleshooting Reference Information Advanced Manual found here http www onkyo com manual
25. R When Completed appears press OON STANDBY on the main unit to turn the unit into standby mode Then updating will be completed e The unit automatically turns itself into standby mode 3 minutes after Completed appears on the display In this case also updating will be completed 2 Making the Initial Setup with the Setup Wizard Read before starting the procedure Set up by answering the guidance displayed on the TV screen Select the item with the cursor buttons of the remote controller and press ENTER to confirm your selection To return to the previous screen press RETURN e If you terminate the procedure on the way or change the setting made in the initial setup and want to call up the setup wizard again press RCV and then HOME on the remote controller select Setup 7 Hardware Setup Initial Setup and press ENTER Select the language first In the next screen the summary of the setup wizard as below will be displayed Select Yes in this screen and press ENTER on the remote controller tt nal Setup Welcome to initial setup Have you connected al the speakers and devices Now would you ike tost st Step ent Room Calibration 2nd Step Source Connection 3rd Step Remote Mode Setup 4th Step Network Connection The setup wizard proceeds in the four steps as below E 1st Step AccuEQ Room Calibration E 2nd Step Source Connection E 3rd Step Remote Mode Setup E 4th
26. Speaker Settings Speaker Impedance and change the default value from 6ohms Default Value to 4ohms 1 2 5 8 12 15 mm Cut and remove the plastic coating from the end of the speaker cable twist the core and connect it to the terminal Make correct connection between the unit s jacks and speaker s jacks to and to for each channel If connection is wrong a bass sound may become poor due to reverse phase Attaching the supplied colored speaker cable labels to the side on the both ends of each channel s cable will help correct connection Up to two subwoofers with built in power amplifier can be connected to the subwoofer jacks Set the cut off filter selection switch of the subwoofer to DIRECT If the subwoofer does not have a cut off filter selection switch but has a cut off frequency adjusting dial turn it to the maximum frequency If your subwoofer does not have builtin power amplifier you can connect a power amplifier between the unit and the subwoofer e The speaker setting is 7 2 ch at the time of purchase You can change it manually or by using automatic speaker setting e Short circuiting the cable and cable or contacting the cable core to the rear panel of the unit may cause failure Also do not connect two or more cables to one speaker terminal or one speaker to several terminals e Using a speaker with less impedance than the setting may result in failure
27. Step Network Connection E 1st Step AccuEQ Room Calibration The test tone coming from each speaker will be measured to enable setting of the number of speakers volume level each speaker s optimum crossover frequencies and distance from the primary listening position and also enable correction of distortion caused by the room acoustic environment e You cannot return to the previous screen during speaker setup even if you press RETURN 82 06 te Initial Setup Accu Room Calibration 1 Place the speaker setup microphone When the start screen above is displayed before starting the procedure place the supplied speaker setup microphone at the measurement position by referring to the figure below D OI w a e io oO e EI al O Listening area Measurement position with microphone zk Correct measurement will not be possible if the microphone is held by hand Measurement is not possible if headphones are being used gt The subwoofer sound may not be detected since it is extremely low frequencies Raise the subwoofer volume to around the half of its maximum volume and make its frequency to the maximum level A loud test tone will be heard during measurement Measurement may be interrupted if there is ambient noise or radio frequency interference Close the window and turn off the home appliance and fluo
28. TAL IN COAXIAL OPTICAL jacks Digital audio signals are input GND terminal The ground wire of the turntable is connected COMPOSITE VIDEO AUDIO IN jacks Analog video signals and audio signals are input Op MONITOR OUT V jack Video signals are output to the connected monitor or TV via a composite video cable PRE OUT SUBWOOFER jacks A subwoofer with built in amplifier is connected 3 LINE OUT ZONE 2 ZONE 3 jacks Audio output jacks connected to the integrated amplifier for multi zone playback in a separate room wer lt Ki Dem Y y1 Display Lights in the following conditions Z2 Z3 K 1 ZONE 2 or ZONE 3 output is on HDMI HDMI signals are input and HDMI input selector is selected ARC Audio signals are input from ARC compatible TV and TV CD input selector is selected 3D Input signals are 3D USB 2 USB input is selected and USB storage device is connected NET 2 NET input is selected and the unit is connected to the network DIGITAL Digital signals are input and the digital input selector is selected Cursor indicators NET or USB is controlled 1 Both Z2 and Z3 light when the WHOLE HOUSE MODE function Is on 2 USB and NET will flash if the connection is not correct Lights when headphones are connected Lights when NET or USB is controlled Lights according to the type of input digital signals and the listening mode Lig
29. al OB ke o e 20 Si CO E SPEAKERS _ l T PRE OUT Jes LINE OUT e N SES le ke Ce LINE INPUT EK Se 4 Subwoofer with built in Surround R Surround L power amplifier Characteristics of speaker types output front stereo sound outputs center sounds such as dialogs and vocals OO create back sound field reproduces bass sounds and creates rich sound field Connecting D speakers or QW speakers enables playback in 7 1 ch configuration D speakers improve sense of envelopment created by back sound field as well as seamlessness of back sounds providing more natural sound experiences in the sound field Q4 speakers produce surround effects on a height plane This unit performs optimal sound field processing for the type of the installed height speakers which is registered in initial settings with setup wizard Instructions on how to connect speakers Important Connect speakers with 4 Q to 16 Q impedance You have to change the setting if any of the speakers have 4 Q or more to less than 6 Q impedance You can set up by viewing the guidance displayed on the TV screen Select the item with the cursor buttons of the remote controller and press ENTER to confirm your selection To return to the previous screen press RETURN Press RCV and then HOME on the remote controller Select Setup 2 Speaker Setup
30. ance the low pitched range m Muting Temporarily Press MUTING on the remote controller To cancel the muting press MUTING again or press VOL A V m Changing the Display Brightness Press DIMMER on the remote controller The display brightness changes each time you press the button m Checking the Input Format Press DISPLAY on the remote controller several times to switch the display of the main unit in order of Input source amp volume Listening mode Signal format Sampling frequency Input signal resolution Output resolution e If Dolby D 5 1 is displayed in signal format the Dolby Digital 5 1 ch signals are being input When listening to AM FM radio the band frequency and preset number are displayed Step 3 2 Listening to AM FM Radio The Basic Manual explains the method using automatic tuning For manual tuning see the Advanced Manual 1 Press TUNER on the main unit several times to select either AM or FM 2 Press TUNING MODE on the unit so that the AUTO indicator on the display lights 3 Press YTUNINGA on the unit The automatic tuning to a radio station starts Searching stops when one is tuned When tuned into a radio station the gt TUNED a indicator on the display lights The FM STEREO indicator lights if the radio station is an FM radio station gt TUNED 4 AUTO auto REO FM Actual display v
31. and Asian models Direct or THX Phase Matching Bass Suppress phase shift in the midrange to enhance bass sound Thus smooth and powerful bass sound can be obtained e It cannot be set if the listening mode is Pure Audio European Australian and Asian models Direct or THX Subwoofer Level Center Level Adjust the speaker level while listening to the sound The adjustment you made will be reset to the previous status when you turn the unit to standby mode e The speakers cannot be adjusted if they have been set to No or None in Setup 2 Speaker Setup Speaker Configuration AccuEQ Room Calibration Disables the sound field correction setting set in the automatic speaker setting The setting can be separately set to each input e This setting cannot be selected if the automatic speaker setting has not been performed e It cannot be set if headphones are connected or the listening mode is Pure Audio European Australian and Asian models or Direct Late Night Make small sounds to be easily heard It is useful when you need to reduce the volume while watching a movie late night You can enjoy the effect on Dolby Digital Dolby Digital Plus and Dolby TrueHD sources only e Turning the unit to standby mode will set the setting to Off In case of Dolby TrueHD the setting will be set to Auto e You cannot use the function during Dolby TrueHD playback if Setup 3 Audio Adjust Dolby Loudness
32. aries depending on the country Registering an AM FM Radio Station It allows you to register up to 40 of your favorite AM FM radio stations 1 Tune into the AM FM radio station you want to register 2 Press MEMORY on the unit The preset number on the display flashes 3 Repeatedly press PRESET on the unit to select a number between 1 and 40 while the preset number is flashing about 8 seconds 4 Press MEMORY on the unit again to register When registered the preset number stops flashing To select a preset radio station press PRESET on the main unit or CH on the remote controller 3 Connecting and playing the Bluetooth enabled device You can wirelessly enjoy music files stored in a smartphone or other Bluetooth enabled device The coverage area is 48 feet 15 meters EE K oo i i y e The Bluetooth enabled device needs to support the A2DP profile e Note that connection is not always guaranteed with all Bluetooth enabled devices Pairing Pairing is necessary when using the Bluetooth enabled device for the first time Before starting the procedure learn how to enable the Bluetooth setting function and to connect with other devices on the Bluetooth enabled device 1 Press BLUETOOTH on the remote controller The unit enters the pairing mode and the BLUETOOTH indicator starts flashing 2 While the BLUETOOTH indicator is flashing compl
33. audio of an MHL enabled mobile device TONE and Tone Level buttons Adjusts the high tone and low tone Input selector buttons Switches the input to be played USB port A USB storage device is connected so that music files stored in it can be played SETUP MIC jack The supplied speaker setup microphone is connected HYBRID STANDBY indicator Lights if the unit enters standby mode when the HDMI Through network standby or Wakeup via Bluetooth function is enabled Di mei 4 GO HFID GR ei E came 3 Frans 2 san 1 ppm MAIN oer J J four OUT SUB Rear Panel PRE OUT _ LINE OUT BZ AC INLET s European and Taiwanese models Ee RI REMOTE CONTROL jack An Onkyo product with RI jack can be connected and synchronized with this unit ANTENNA AM FM 75 Q terminal The supplied antennas are connected COMPONENT VIDEO IN OUT jacks Component video input output jacks ETHERNET port Used for LAN connection HDMI IN OUT jacks Digital video signals and audio signals are transmitted between the unit and the connected devices SPEAKERS terminals Speakers are connected To use the multi zone function connect the speakers in the separate room to the ZONE2 speaker terminals Power cord North American Australian and Asian models AC INLET European and Taiwanese models The power cord is connected DIGI
34. ays come back to remote setup from setup 8 2 Remote Made Setup Yes No Skip In this step you can enable operation of the other components using the remote controller of the unit When the Remote Mode Setup start screen is displayed select Yes with the cursors and press ENTER on the remote controller Follow the guidance to select the desired REMOTE MODE button and in the keyboard screen enter the first three characters of the brand name of the device you are going to program e g ONK for ONKYO and search for the remote control code The guidance will also explain how to set the remote controller E 4th Step Network Connection fei Initial Setup Network Connection Do you want to connect network connection It gives you network services that our AV select No Skip Gi receiver support you wish to skip this step Yes No Skip You can check the network connection and make the Wi Fi setting When the Network Connection start screen is displayed select Yes with the cursors and press ENTER on the remote controller If you select Wired in the next screen you can view the LAN cable connection status To make the Wi Fi setting select Wireless press ENTER on the remote controller and follow the sections below Make the following preparations Wi Fi connection requires an access point such as wireless LAN router Write down the SSID and password key of the acce
35. connection between the digital audio out optical jack of the TV and the DIGITAL IN OPTICAL jack of the unit or an analog audio cable connection between the audio output jack of the TV and the VIDEO AUDIO IN TV CD jack of the unit Audio connection with a TV not supporting ARC Select an appropriate connection for your TV Another TV can be connected to the HDMI OUT SUB jack In this case change the setting accordingly You can set up by viewing the guidance displayed on the TV screen Select the item with the cursor buttons of the remote controller and press ENTER to confirm your selection Press RCV and then HOME on the remote controller select Setup 1 Input Output Assign Monitor Out and set the default value of MAIN to SUB or MAIN SUB The unit supports the HDMI Through function that allows transmission from players to the TV even if the unit is in standby You have to modify the settings to enable the input selection link with CEC compliant device connection with ARC compatible TV and HDMI Through function See the section 2 2nd Step Source Connection of Step 2 Setting Up e To enjoy HDCP2 2 protected video connect the player to the HDMI IN3 jack and the TV to the HDMI OUT MAIN jack of the unit Your player and TV need to support HDCP2 2 To play 4K or 1080p video use the high speed HDMI cable It is possible to send video and audio of an
36. d the Wi Fi indicator on the left of the unit s display starts flashing When connection has been established the Wi Fi indicator changes from flashing to staying lit If the Wi Fi indicator does not stay lit connection has not been established Make the setting again If Push Button does not work try Enter Password When the access point is not displayed Select Other with the cursor on the remote controller and press ENTER to display the keyboard screen Input the SSID and password Make the following settings according to the router setting m WPA WPA2 method Select WPA or WPA2 in Security Method select OK and press ENTER Em WEP method Select WEP in Security Method and select Default Key ID Then select OK and press ENTER e If encryption setting has not been made on the wireless LAN router select None in Security Method select OK and press ENTER E Exiting the setup wizard After finishing the initial setup keep Finished selected and press ENTER on the remote controller Connection and setting of the unit is now completed See Step 3 and enjoy your home theater Step 3 Playing Back 1 Playing the player and TV CUP 6 Gi el el el d LTH GOH o To control the unit The remote controller of this unit has the remote mode function for controlling other devices You cannot control this unit when the remote controller is in the remote mode o
37. ding technology licensed from Fraunhofer IIS and Thomson All other trademarks are the property of their respective owners DISCLAIMER Through this device you are able to link to other services or websites which are not under the control of any company which has designed manufactured or distributed have distributed this device and its affiliates collectively Company We have no control over the nature content and availability of those services The inclusion of any links does not necessarily imply a recommendation or endorse the views expressed within them All information content and services available through this device belong to third parties and are protected by copyright patent trademark and or other intellectual property laws of applicable countries The information content and services provided through this device are for your personal noncommercial use only Any information content or services may not be used in any manner other than previously approved by the appropriate content owner or service provider You may not modify copy republish translate exploit create derivative works upload post transmit sell or distribute in any manner any information content or services available through this device unless expressly permitted by the appropriate copyright patent trademark and or other intellectual property owner including without limitation content owner or service provider THE CONTENT AND SERVIC
38. e with the normal speakers Dolby Enabled Speakers designed with their output facing toward the ceiling to create an elevated audio effect in the Dolby Atmos and Dolby Surround listening modes by providing sounds echoing off the ceiling You can select or h on the unit For connection with the unit use the SPEAKERS BACK or HEIGHT terminals E Other connections AM FM antenna connections Connect the antennas to listen to AM FM broadcast When listening to the broadcast for the first time adjust the antenna position and orientation to get the best reception AM loop antenna supplied En D r Ty Indoor FM antenna supplied GE Fix with a tack on the wall North American and Taiwanese models European Australian and Asian models Step 1 Network connection You can enjoy Internet radio and DLNA by connecting the unit to LAN The unit can be connected to the router with an Ethernet cable or to the wireless LAN router with Wi Fi connection In case of wired connection connect the Ethernet cable to the Ethernet port See the section 2 4th Step Network Connection of Step 2 Setting Up Internet radio ja J NAS CERTIFIED Headphones connection Connect stereo headphones with a standard plug 1 4 inch or 6 3 mm to the PHONES jack on the front panel Sound from the speakers will be off while you are using
39. ection is correct video audio of the input source selected on the unit will be played Step 2 After checking the connection select Yes with the cursors and press ENTER e If you select No and press ENTER the error cause will be displayed Follow the guidance to remove the error cause and check the connection again Select Yes with the cursors and press ENTER on the remote controller to check the connection of other inputs or select No Done Checking and press ENTER to skip If you select Yes you will return to the screen of step 2 If you select No Done Checking you will proceed to step 5 Enabling HDMI Linked Operation and Other Functions In the next screen you can enable the HDMI linked operation with CEC compliant device connection with ARC compatible TV and HDMI Through function Select Yes with the cursors to enable them or No Done Checking to skip and press ENTER on the remote controller Select Yes with the cursors and press ENTER to enable the CEC link function or select No and press ENTER to keep it disabled fei Source Connection The following CEC compatible devices are found Do you wish to turn on the CEC link Integra DHS 8 8 If you select Yes the connection with ARC compatible TV and HDMI Through function will be set to Auto and enabled E 3rd Step Remote Mode Setup E pase ze Remote Mode Setup connected You can alw
40. ete connection on the Bluetooth enabled device in the nearby area within about 2 minutes If the name of this unit is displayed on the Bluetooth enabled device s display select this unit Paring will end after a short time e If a password is requested enter 0000 e When connecting the unit to any other Bluetooth enabled device start pairing by pressing and holding BLUETOOTH until the BLUETOOTH indicator starts flashing This unit can store the data of up to eight paired devices Playing sound of the Bluetooth enabled device If the unit is on and the Bluetooth enabled device is connected the input will be automatically switched to BLUETOOTH Play music in this state It may take about a minute until connection is established when the unit is on since the Bluetooth function takes some time to start up If the volume setting on the Bluetooth enabled device is low the sound will not be output from this unit e Due to the characteristics of Bluetooth wireless technology the sound produced on this unit may slightly be behind the sound played on the Bluetooth enabled device 4 Using the HOME menu In the HOME menu you can make advanced settings and use Internet radio and DLNA For details on the operation see the Advanced Manual 1 After pressing RCV press HOME on the remote controller The HOME menu is displayed on the TV screen You can also use the HOME button on the main unit ft HOME o mB o e
41. hts when Music Optimizer is enabled Lights in the following conditions AUTO Tuning mode is auto gt TUNED 4 Receiving AM FM radio Fa flashes while tuning is automatically performed FM STEREO Receiving FM stereo RDS European Australian and Asian models Receiving RDS broadcasting MUTING Flashes when muting is on Lights in the following conditions SLEEP Sleep timer has been set ASb Auto Standby is on ch Channel is being set Hz Crossover frequencies are being set m ft Speaker distances are being set dB Speaker volume is being set Q Displays various information of the input signals Pressing DISPLAY displays the type of input digital signals and the listening mode Troubleshooting Before starting the procedure Problems may be solved by simply turning the power on off or disconnecting connecting the power cord which is easier than working on the connection setting and operating procedure Try the simple measures on both the unit and the connected device If the problem is that the video or audio is not output or the HDMI linked operation does not work disconnecting connecting the HDMI cable may solve it When reconnecting be careful not to wind the HDMI cable since if wound the HDMI cable may not fit well After reconnecting turn off and on the unit and the connected device The AV receiver turns off unexpectedly e The AV receiver will automatically enter sta
42. ndby mode when Auto Standby is set and launched There s no sound or it s very quiet e A wrong input selector button has been selected Select a correct input for the player Also check that muting is not on e Not all listening modes use all speakers There s no picture e A wrong input selector button has been selected European Australian and Asian models To display video from the connected player on the TV screen while the unit is in standby you need to enable HDMI Through function When the TV image is blurry or unclear power cord or connection cables of the unit may have interfered In that case keep distance between TV antenna cable and cables of the unit If you connect a player supporting HDCP2 2 be sure to connect it to the HDMI IN3 jack of the unit At the time connect the TV to the HDMI OUT MAIN jack Video is not displayed if the listening mode is Pure Audio HDMI control does not function correctly e Set the CEC link function of the unit to on It is also necessary to make the HDMI linked system setting on the TV See the TV s instruction manual for details The remote controller does not work e Be sure to press RCV first before operating the unit with the remote controller There is no sound for multi zone function e With multi zone function sound is output only when the signal input source is an external component connected to the analog audio input jacks of the unit NET USB BLU
43. olby TrueHD via network and USB storage device the supported formats will differ depending on the use environment Supplied Accessories Indoor FM antenna 1 AM loop antenna 1 ASS i Color labels for speaker cable 1 Remote controller RC 882M 1 Batteries AA R6 2 Power cord European and Taiwanese models 1 Speaker setup microphone 1 gt The number in parenthesis indicates the quantity On packaging the letter at the end of the product name indicates the color How to use the remote controller ee D eg CNS EI Luc Remote control sensor Batteries AA R6 AV Receiver Approx 16 ft 6 m If you do not use the remote controller for a long time remove the batteries to prevent leakage Note that keeping consumed batteries inside may cause corrosion resulting in damage of the remote controller Step 1 Connections HDMI ASSIGNABLE K HDCP22 4K 3 STB DVR 2 CBL SAT 1 OUT OUT BD DVD MAIN Bate gt CS cS Personal computer HDMI cable oOboo0o0o00o0 Game console Set top box Digital video recorder etc 1 Connecting the TV and players Important The power cord must be connected only after all other connections are completed HDMI cable connection The unit has many HDMI jacks on its rear
44. ovide purer sound e For details on the listening modes see the Advanced Manual Direct for playing the input signals as is Selecting this mode allows the input signals to be played as they are For example 2 ch signals of music CD will be played in stereo 5 1 ch signals in 5 1 ch and Dolby Digital signals of blu ray disc or DVD in the Dolby Digital sound field according to the specified number of channels Other useful functions m Playing Video and Audio from Different Sources It is possible to play audio and video from different sources For example you can play audio from the CD player and video from the BD DVD player In this case press BD DVD and then TV CD Then start playback on the BD DVD player and CD player This function is effective when an input with audio only has been selected TV CD TUNER or PHONO in the initial setting E Adjusting Sound Quality It is possible to enhance or moderate the low and high pitched ranges of front speakers Press TONE on the main unit several times to select the desired setting from Bass Treble and Phase Matching Bass and adjust with e It cannot be set if the listening mode is Pure Audio European Australian and Asian models Direct or THX Bass Allows you to enhance or moderate the low pitched range Treble Allows you to enhance or moderate the high pitched range Phase Matching Bass Allows you to keep the clear midrange and effectively enh
45. panel and each of them corresponds to an input selector button of the same name on the front panel For example a Blu ray Disc player will be connected to the HDMI IN1 jack and the BD DVD button on the front panel will be used to listen to the playback sound if the player is CEC compliant input will be switched automatically If you add another Blu ray Disc player you can use any other jack than HDMI IN1 It is possible to change assignment of the input jacks and E E L TV 7 or To use the ARC function connect to the ARC compatible HDMI jack of the TV and make an appropriate setting on the unit See the section 2 2nd Step Source Connection of Step 2 Setting Up Blu ray Disc DVD player Satellite Cable set top box etc input selector buttons For how to make settings see the Advanced Manual To connect the TV and the unit connect the HDMI OUT MAIN jack of the unit and the HDMI IN jack of the TV using an HDMI cable With this connection it becomes possible to display the setting screen of the unit on the TV or transmit video audio signals from the player to the TV If your TV supports ARC Audio Return Channel it is possible to play the TV sound with the AV receiver s speakers with this connection only If your TV does not support ARC you need in addition to the HDMI OUT MAIN jack connection a digital optical cable
46. rescent light 2 After placing the microphone at the measurement position select Do it Now with the cursors and press ENTER 3 When Please plug microphone that came ina box with AV receiver is displayed connect the microphone to the SETUP MIC jack of the unit SETUP MIC jack ot aes Speaker setup le microphone CO e H 4 Follow the guidance displayed on the TV screen B Aert Room Caibration Front Speakers Type Height Speakers Type Not se Powered one 2 D D D Set biamp only if you use 2 channel amp for each front speaker When the screen above is displayed set the items with 6 When the measurement is completed the measurement result is displayed Press lt 4 on the remote controller to check the settings Press ENTER with Save selected In the next screen showing that AccuEQ Room Calibration is On press ENTER on the remote controller e If there is an error message follow the on screen instruction to remove the error cause About THX playback THX recommends setting the speakers manually if you use THX certified speakers or playing back with THX listening modes e THX recommends setting the crossover frequency to 80Hz THX manually e Due to the electrical complexities and the interaction with the room you may notice irregular results when setting the level or distance of each speaker If this happens THX recommends setting the speake
47. rs and the subwoofer manually 7 When Please unplug setup microphone is displayed disconnect the microphone E 2nd Step Source Connection You can check whether or not each input source is connected correctly the cursors on the remote controller Select the types for height speakers if the height speakers are used Confirm the power supply of subwoofer and press ENTER on the remote controller in the next screen Confirm the position of speaker setup microphone and press ENTER on the remote controller in the next screen e When the cursor is on an item the content of the item will be shown on the lower left of the screen 5 The test tones sound from the connected speakers and automatic speaker setting starts Measurement will be made twice for each speaker It takes several minutes to be completed Keep the room as quiet as possible during measurement If any of the speakers do not produce the test tone check for disconnection e During measurement each speaker outputs the test tones at a high volume Be careful of sound leak that may disturb your neighbors or be careful not to frighten young children 1 When the Source Connection start screen is displayed select Yes Continue with the cursors and press ENTER fei Ina Setup 3 0 Source Connection Yes Continue No Skip Select the desired input to check the connection and press ENTER Start playback of the selected device If conn
48. s you to quickly access the frequently used setting items including input selection and volume adjustment Listening mode buttons Allows you to select the listening mode DIMMER button Switches the brightness of the display ZONE2 button and ZONES button For use when the unit is connected with a pre main amplifier in a separate room and sound is played there MUTING button Temporarily mutes audio VOLUME buttons Allows you to adjust the volume This button also cancels the muting 4D RETURN button Returns the display to the previous state 2 HOME button Displays the HOME menu that allows you to make advanced settings and use Internet radio and DLNA 3 DISPLAY button Switches the information on the display e The buttons other than those above are for operating other devices Listening modes You can select a listening mode from various options such as Dolby Atmos Dolby Digital and DTS Select the desired mode by switching and listening actual sound in different modes The selectable listening modes depend on the format of the input signals MOVIE TV You can select a listening mode suitable for movies and TV programs MUSIC You can select a listening mode suitable for music GAME You can select a listening mode suitable for games THX You can select a THX listening mode PURE AUDIO main unit only European Australian and Asian models The display and analog video circuits are cut off to pr
49. ss INPUT SELECTOR of the input to be played in a separate room e If you turn the unit to standby during multi zone playback the Z2 Z3 indicators are dimmed and the playback mode is switched to playback in a separate room only Performing steps 1 and 2 while the unit is in standby also switches the playback mode to playback in a separate room only To play the same source in the main room and separate room hold down ZONE2 or ZONES for approximately 3 seconds To control on the main unit Press ZONE2 or ZONE3 and within 8 seconds press the input selector button of the input to be played in a separate room To play the same source in the main room and separate room press ZONE2 or ZONES twice To turn off the multi zone function Press ZONE2 or ZONES on the remote controller and press RECEIVER To control on the main unit press ZONE2 or ZONE3 and within 8 seconds press OON STANDBY e If Zone 2 or Zone 3 is on power consumption during standby becomes larger than normal e If Zone 2 or Zone 3 is turned on when the listening mode of the main room is Pure Audio it will automatically switch to Direct European Australian and Asian models e While Zone 2 or Zone is on the RI linked system function interlink between Onkyo components is disabled e Pressing INPUT SELECTOR on the remote controller while you are using the remote controller for Zone 2 or Zone 3 will switch the controlled target to the main room To control Zone 2 or
50. ss point if they are shown in the label of the main body If the access point has an automatic setting button may be called differently according to the manufacturer you can set up without inputting the password For how to use the automatic setting button of the access point refer to its instruction manual zk The unit supports Wi Fi connection with 2 4 GHz access point 1 Select the SSID of the access point to be connected with the cursor buttons and press ENTER When the SSID of the access point appears on the TV screen select the desired access point e If you changed the initial setting of the access point to skip password entry Step 3 starts automatically e If you changed the initial setting of the access point to hide the SSID see When the access point is not displayed 2 Select and set the authentication method The Enter Password screen instead of the following screen may be displayed automatically if the wireless LAN router does not have an automatic setting button E Fi soup Select the authentication method Enter Password Push Bution PIN code When the screen above is displayed select and set one of the three authentication methods Enter Password Push Button and PIN code See below for details of and how to set each method Enter Password Enter the password of the access point to establish connection Select Enter Password with the cursor buttons and press ENTER
51. t RI 1 USB 1 Front Ethernet 1 Specifications and features are subject to change without notice Others License and Trademark Information Q1 DOLBY Manufactured under license from Dolby Laboratories Dolby Dolby Atmos Dolby Surround Surround EX and the double D symbol are trademarks of Dolby Laboratories S dts np Master Audio For DTS patents see http patents dts com Manufactured under license from DTS Licensing Limited DTS DTS HD the Symbol amp DTS and the Symbol together are registered trademarks and DTS HD Master Audio is a trademark of DTS Inc DTS Inc All Rights Reserved QDEO Qdeo and QuietVideo are trademarks of Marvell or its affiliates Re Equalization and the Re EQ logo are trademarks of THX Ltd THX SELECT 2 PLUS Manufactured under license from THX Ltd THX and the THX logo are registered in the U S and other jurisdictions All rights reserved Surround EX is a trademark of Dolby Laboratories Used with permission U S Pat nos 7 254 239 amp 7 593 533 amp 7 974 425 amp 8 452 028 amp 8 509 457 Taiwan Pat 1238671 European Pat 1 360 874 THX Select2 Plus Before any home theater component can be THX Select2 Plus certified it must pass a rigorous series of quality and performance tests Only then can a product feature the THX Select2 Plus logo which is your guarantee that the Home Theater products you purchase will give you superb performance for many years
52. the headphones e If you selected any other listening mode than Pure Audio European Australian and Asian models Stereo Mono and Direct connecting headphones will switch the listening mode to Stereo Step 2 Setting Up Important When the unit is turned on for the first time the setup wizard of the section 2 will automatically be launched If you use the setup wizard to make the initial setup connect a TV to the HDMI OUT MAIN jack of the unit via HDMI connection 1 Turning the power on Connect the power cord to the outlet Press OON STANDBY on the main unit or ORECEIVER on the remote controller to turn the unit on or to standby mode ONKYO owent D m mmm European and Taiwanese models include a removable power cord Connect the power cord to AC INLET of the unit and then connect to the outlet Always disconnect the outlet side first when disconnecting the power cord When the unit is turned on a large instantaneous current may flow affecting functionality of the computer and other devices It is recommended to use a separate outlet from that for the computer or such other sensitive devices Firmware update notification If the unit is connected via LAN and there is firmware update available the Firmware Update Available message will appear To execute updating select Update Now with the cursor buttons of the remote controller and press ENTE
53. ther than RECEIVER mode for controlling this unit Be sure to press RCV to select the RECEIVER mode before starting operation 1 Turn the power on Press ORECEIVER on the remote controller to turn the power on e Switch the input on the TV to that assigned to the unit Use the TV s remote controller 2 Select the input of the unit and start playback on the player or TV Press INPUT SELECTOR to which the desired player has been assigned Press TV CD to play the TV s sound You can also use the input selector buttons on the main unit e Input will automatically be selected if the TV or player is CEC compliant and connected to the unit with HDMI cable 3 Select the desired listening mode Press the listening mode buttons to switch the mode so that you can enjoy different listening modes For details about the listening modes see Listening modes on the next page 4 Adjust the volume with 0 REMOTE M DE TV ZONE2 SEARCH REPEAT RANDOM MOVIE TV MUSIC Remote controller parts name ORECEIVER button Turns the unit on or into standby mode RCV button Switches the remote controller to the mode for operating this unit REMOTE MODE INPUT SELECTOR button Switches the input to be played Cursor buttons and ENTER button Moves the cursor and confirms the selection Q SETUP button Displays the Quick Setup menu that allow
54. tivity antenna s performance operating system software application etc General Power Supply AC 120 V 60 Hz North American and Taiwanese AC 220 240 V 50 60 Hz Others Power Consumption 6 9 A North American and Taiwanese 690 W Others 0 1 W Stand by North American and Taiwanese 0 2 W Stand by Others 85 W No sound Dimensions W x H x D 435 mm x 175 mm x 379 mm 17 1 8 x 6 7 8 x 14 15 16 Weight 11 5 kg 25 4 Ibs e HDMI Input IN1 BD DVD 4K IN2 CBL SAT 4K IN3 STB DVR 4K HDCP2 2 IN4 GAME 4k INS PC IN6 AUX INPUT HDMI MHL Front Output OUT MAIN ARC HDCP2 2 OUT SUB Video Resolution Pass through 4K 60 Hz YCbCr 4 2 0 Upscaling 4K 30 Hz Audio Format DTS HD Master Audio DTS HD High Resolution Audio Dolby Atmos Dolby TrueHD Dolby Digital Plus DSD Multichannel PCM Supported 3D Audio Return Channel DeepColor x v Color LipSync CEC RIHD 4K Upscaling and Passthrough Video Inputs Component IN CBL SAT Composite IN1 CBL SAT IN2 STB DVR IN3 GAME Video Outputs Component OUT Composite MONITOR OUT Audio Inputs Digital OPTICAL TV CD COAXIAL 1 BD DVD 2 CBL SAT Analog BD DVD CBL SAT STB DVR GAME PC TV CD PHONO Audio Outputs Analog ZONE2 LINE OUT ZONE3 LINE OUT 2 SUBWOOFER PRE OUT Speaker Outputs FRONT L R CENTER SURROUND L R BACK or HEIGHT L R ZONE2 UR Phones PHONES Front o 6 3 e Others Setup Mic 1 Fron
55. to come THX Select2 Plus requirements define hundreds of parameters including power amplifier performance and pre amplifier performance and operation for both digital and analog domains THX Select2 Plus receivers also feature proprietary THX technologies e g THX Mode which accurately translate movie soundtracks for home theater playback AccuEQ Music Optimizer RIHD and WRAT are trademarks of Onkyo Corporation RIHD and RIHD logo are trademarks of Onkyo Corporation HAT HIGH DEFINITION MULTIMEDIA INTERFACE The terms HDMI and HDMI High Definition Multimedia Interface and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries QUFi CERTIFIED The Wi Fi CERTIFIED Logo is a certification mark of the Wi Fi Alliance Wi Fi certified logo shows international association certifying interoperability Wi Fi alliance ensures the product has passed the test for compatibility with other Wi Fi certified equipment 3 Bluetooth The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG Inc and any use of such marks by Onkyo is under license Other trademarks and trade names are those of their respective owners Onkyo does not guarantee Bluetooth compatibility between the AV receiver and all Bluetooth enabled devices For compatibility between the AV receiver and another device with Bluetooth technology consult the device
56. will not be adjusted In Custom you can adjust the brightness contrast hue and saturation as desired If you do not adjust the resolution and image quality select Bypass e Wide Mode and Picture Mode can be set only on the video output from the HDMI OUT MAIN jack e Video cannot be selected if the input is NET USB or BLUETOOTH E Information Audio Displays the audio input source format number of channels sampling frequency listening mode number of output channels and other audio information Video Displays the video input source resolution signal format color tone 3D information Aspect Picture Mode output and other Video information Tuner Displays the band frequency preset number and other tuner radio information m Listening Mode Select the listening mode from the categories of MOVIE TV MUSIC GAME and THX e It cannot be set when audio is played from the TV s speakers Making multi zone connection 6 Using the multi zone function You can multi zone connect the unit with an integrated amplifier and speakers in a separate room and play sound from an external device connected to the analog audio input jacks of the unit sound from the NET USB or BLUETOOTH source and the AM FM broadcasting It is possible to perform playback in the main room and a separate room at the same time for example by playing the Blu ray Disc player in the main room where the unit is
57. z zasadniczymi wymaganiami i innymi w a ciwymi postanowieniami Dyrektywy 1999 5 EC Eu Onkyo Corporation declaro que o TX NR737 cumpre os requisitos essenciais e outras provis es relevantes da Directiva 1999 5 EC Prin prezenta Onkyo Corporation declar c aparatul TX NR737 este n conformitate cu cerin ele esen iale si cu alte prevederi pertinente ale Directivei 1999 5 CE Onkyo Corporation t mto vyhlasuje e TX NR737 a spina z kladn po iadavky a v etky pr slu n ustanovenia Smernice 1999 5 ES 22 Onkyo Corporation izjavlja da je ta TX NR737 v skladu z bistvenimi zahtevami in drugimi relevantnimi dolo ili direktive 1999 5 ES Onkyo Corporation vakuuttaa t ten ett TX NR737 tyyppinen laite on direktiivin 1999 5 EY oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen H rmed f rklarar Onkyo Corporation att denna TX NR737 f ljer de v sentliga kraven och andra relevanta stadgar i Direktiv 1999 5 EC H r me l sir Onkyo Corporation v yfir a varan TX NR737 er samr mi vi grunnkr fur og a rar kr fur sem ger ar eru tilskipun 1999 5 EC Onkyo Corporation erkl rer herved at denne TX NR737 er i overensstemmelse med vesentlige krav og andre relevante bestemmelser i direktiv 1999 5 EC Ovime Onkyo Corporation potvr uje da je TX NR737 u suglasnosti sa osnovnim zahtjevima i ostalim relevantnim odredbama Direktive 1999 5 EC ONKYO Onkyo Corporation Kitahama Chuo
Download Pdf Manuals
Related Search