Onkyo A-1VL User's Manual
Contents
1. IMPORTANT A 5 ampere fuse is fitted in this plug Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 5 amperes and that it is approved by ASTA or BSI to BS1362 Check for the ASTA mark or the BSI mark on the body of the fuse IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO ANY 13 AMPERE SOCKET If in any doubt consult a qualified electrician Declaration of Conformity We ONKYO EUROPE ELECTRONICS GmbH LIEGNITZERSTRASSE 6 82194 GROEBENZELL GERMANY declare in own responsibility that the ONKYO product described in this instruction manual is in compliance with the corresponding technical standards such as EN6006S EN55013 EN55020 and EN61000 3 2 3 3 GROEBENZELL GERMANY MORI ONKYO EUROPE ELECTRONICS GmbH Features E 2 ch pre main amplifier that incorporates Onkyo proprietary VL digital amplifier E The DIRECT function that allows you to connect the A 1VL to another amplifier and to use the A 1VL as a power amplifier E The PREOUT terminals that can be used for your system expansion E Independent toroidal transformer for L R channels improves additional sound quality by separating the L R channel voltages to avoid the L R channels from interferring with each other E High2. Panel C POWER button This button is used to set the A 1 VL to On or Off POWER indicator This indicator lights up when the A 1VL is ON While this indicator is illuminated you can operate the A 1 VL with the remote controller MUTING indicator This indicator lights up when the Muting function is set VOLUME control This control is used to set the volume of the A 1VL Rear Panel Remote control sensor This sensor receives control signals from the remote controller Input selector control This control is used to select following input sources CD LINE 1 LINE 2 TUNER and PHONO DIRECT button Turns on or off the DIRECT function When you use the A 1 VL as a power amplifier turn on the DIRECT function PHONO These analog inputs can be used to connect a turntable with a moving magnet cartridge TUNER These inputs can be used to connect a tuner CD These inputs can be used to connect a CD player with analog outputs PREOUT If you use the A 1VL as a preamp these analog pre out can be connected to the inputs on a power amp MAIN IN If you use the A 1 VL as a power amp these analog inputs can be connected to the outputs on a separate preamp ohms mn SPEAKEE SPEAKER IMPEDANCE SELECTOR AC INLET SPEAKERS These terminal posts are for connecting your speakers Grounding screw This screw is for connecting a turntable s ground wire
3. not subjected to direct sunshine or inverter type florescent lights Relocate if necessary page 8 e Ifthe A 1VL is installed in a rack or cabinet with colored glass doors the remote controller may not work reliably when the doors are closed page 8 Recording Can t record e On your recorder make sure the correct input is selected The A 1 VL is not equipped with digital input output terminals and can perform only analog recording page 13 The signal from the component connected to the MAIN IN terminal cannot be recorded The A 1VL contains a microcomputer for signal processing and control functions In very rare situations severe interference noise from an external source or static electricity may cause it to lock up In the unlikely event that this happens unplug the power cord from the wall outlet wait at least five seconds and then plug it back in again Onkyo is not responsible for damages such as CD renial fees due to unsuccessful recordings caused by the unit s malfunction Before you record important data make sure that the material will be recorded correctly Specifications Power Output Dynamic Power THD Total Harmonic Distortion Damping Factor Input Sensitivity and Impedance Output Level and Impedance Phono Overload Frequency Response SN Ratio Speaker Impedance Power Supply Power Comsumption Dimensions W x H x D Weight Analog Inputs Analog Outputs Pre Outputs Speaker
4. quality speaker terminal components that minimize signal degradation Supplied Accessories Make sure you have the following accessories Remote controller RC 573A 1 amp Power cord 1 two batteries AA R6 2 In catalogs and on packaging the letter added to the end of the product name indicates the color of the A 1 VL Speci fications and operation are the same regardless of color Table of Contents Introduction Important Safety Instructions Precautions Features Supplied Accessories Table of Contents Front amp Rear Panels Front Panel Rear Panel Remote Controller Remote Controller RC 573A Inserting the Batteries Using the Remote Controller Connections Connecting the A 1VL Before Making Any Connections Connecting Your Speakers Connecting Your Speakers Changing the Speaker Impedance Value Setting Audio Components Connecting a CD Player Connecting an Audio Output Component Such as a TV Connecting a Cassette or MD Recorder Connecting a Tuner Connecting a Turntable Connecting a Power Amplifier Connecting a Preamp Connecting the Power Cord Enjoying Audio Sources Turning on the A 1VL Playing a Connected Component Muting the A 1VL Using the DIRECT Function Recording Others MEN ICSE ooreen eae EEEE EEEE EAE Specifications o cccssccccscsecescsssesscccescssncessnaceccsnccvesssvessanceessocceesasccssuscsessuacessaccecssecersesuceessccessvsceressncey Front amp Rear Panels Front
5. E OHMS MIN SPEAKER SPEAKER IMPEDANCE SELECTOR 10 Connecting the A 1VL Continued Audio Components Connecting a CD player Use an analog audio cable RCA phono to connect the A 1VL s CD L R inputs to the analog audio outputs on your CD player as shown L AUDIO OUTPUT ANALOG R L Connecting an Audio Output Component Such as a TV Use an analog audio cable RCA phono to connect the A 1VL s LINE 1 L R inputs to the analog audio outputs on your component such as a TV as shown e ooo OUTPUT Ohm Note If your TV has no audio outputs connect the A 1 VL to your VCR and use its tuner Connecting a Cassette or MD Recorder Use an analog audio cable RCA phono to connect the A 1VL s LINE 2 IN L R inputs to the MD recorder or cassette recorder s outputs and use another analog audio cable RCA phono to connect the A 1 VL s LINE OUT L R outputs to the cassette or MD recorder s inputs as shown 6 LINE 2 IN L OC Om L gt Gx L oO Om Connecting a Tuner Use an analog audio cable RCA phono to connect the A 1VL s TUNER L R inputs to the analog audio out puts on your tuner as shown oO Oooo Connecting a Turntable The A 1VL s phono inputs are for use with moving
6. LINE 1 These inputs can be used to connect a TV or other component with analog outputs LINE 2 IN OUT These analog inputs can be used to connect a cassette or MD recorder SPEAKER IMPEDANCE SELECTOR This selector can be used to set the speaker imped ance values according to the speakers you use AC INLET The supplied power cord should be connected here Remote Controller Remote Controller RC 573A Be ee See ee l T e AMP section Use the following buttons to operate the A 1 VL while it is turned on VOLUME 4 buttons These buttons are used to set the volume of the A 1VL 2 MUTING button This button is used to mute the A 1VL This func tion can be set only with the remote controller CD section Use the following buttons to operate the Onkyo s CD player with a remote controller signal sensor such as the C 1VL 3 button This button is used to play CD playback button This button is used to stop CD playback a button This button is used to pause CD playback lt gt button The FR a button is used start fast reverse The FF button is used to start fast forward lt gt button The Previous mea button is used to select the previ ous track During playback it selects the beginning of the current track The Next button is used to select the next track Remote Controller Continued Inserting the Batte
7. ONKYO Contents Integrated Stereo Amplifier irele A e eee ereeeeee 2 A IVL Instruction Manual Connections e eee 9 Enjoying Audio Sources Thank you for purchasing an Onkyo A 1VL Integrated Stereo Amplifier Please read this manual thoroughly Troubleshooting s 2 12 14 before making connections and plugging in the unit Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your A 1VL Please retain this manual for future reference Specifications seseris 15 WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPARATUS WARNING AVIS RISK OF ELECTRIC SHOCK f RISQUE DE CHOC ELECTRIQUE DO NOT OPEN NE PAS OUVRIR TO RAIN OR MOISTURE CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL equilateral triangle is intended to alert the user to the AN presence of uninsulated dangerous voltage within A intended to alert the user to the presence of important The lightning flash with arrowhead symbol within an the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is operating and maintenance servicing instructions in the literature accompanying the appliance Im
8. Outputs Front L R 100 W 100 W 8 Q 1 kHz DIN 310 W 310 W 3 Q Front 240 W 240 W 4 Q Front 130 W 130 W 8 Q Front 2 Power Rated 0 08 1 kHz 1 W 25 Front 1 kHz 8 Q 200 mV 50 kQ LINE 2 5 mV 50 kQ PHONO MM 200 mV 2 2 kQ REC OUT 130 mV MM 1 kHz 0 5 10 Hz 60 kHz 1 dB 3 dB CD 100 dB CD IHF A 70 dB PHONO IHF A 40 16Q AC 230 240 V 50 Hz 105 W 435 W x 81 5 H x 390 D mm 17 1 8 W x 3 3 16 H x 15 3 8 D inches 11 3 kg 24 9 Ibs PHONO TUNER CD LINE1 LINE2 MAIN IN LINE2 1 L R 1 L R Specifications and features are subject to change without notice 15 ONKYO CORPORATION Sales amp Product Planning Div 2 1 Nisshin cho Neyagawa shi OSAKA 572 8540 JAPAN Tel 072 831 8023 Fax 072 831 8124 ONKYO U S A CORPORATION 18 Park Way Upper Saddle River N J 07458 U S A Tel 201 785 2600 Fax 201 785 2650 http Awww onkyousa com ONKYO EUROPE ELECTRONICS GmbH Liegnitzerstrasse 6 82194 Groebenzell GERMANY Tel 49 8142 4401 0 Fax 49 8142 4401 555 http www onkyo net ONKYO EUROPE UK Office KinG Suite 1 Gregories Court Gregories Road Beaconsfield Buckinghamshire HP9 1HQ HONEPRGE UNITED KINGDOM Tel 44 0 1494 681515 Fax 44 0 1494 680452 http www onkyo com ONKYO CHINA LIMITED Units 2102 2107 Metroplaza Tower 223 Hing Fong Road Kwai Chung Printed in Japan N T HONG KONG Tel 852 2429 3118 Fax 852 2428 9039 D0408 2 C Copy
9. ary from country to country Make sure that the voltage in your area meets the voltage requirements printed on the A 1VL s rear panel AC230 240V 50 Hz Never Touch This Unit with Wet Hands Never handle this unit or its power cord while your hands are wet or damp If water or any other liquid gets inside this unit have it checked by your Onkyo dealer Installing This Unit e Install this unit in a well ventilated location Ensure that there s adequate ventilation all around this unit especially if it s installed in an audio rack If the ventilation is inadequate the unit may overheat lead ing to malfunction Do not expose this unit to direct sunlight or heat sources because its internal temperature may rise shortening the life of the optical pickup e Avoid damp and dusty places and places subject to vibrations from loudspeakers Never put the unit on top of or directly above a loudspeaker e Install this unit horizontally Never use it on its side or on a sloping surface because it may cause a malfunction e Ifyou install this unit near a TV radio or VCR the sound quality may be affected If this occurs move this unit away from the TV radio or VCR Moisture Condensation Moisture condensation may damage this unit Read the following carefully When you take a glass containing a cold drink outside on a summer s day drops of water called condensation form on the outside of the glass Similarly m
10. e DIRECT button to turn off the DIRECT function e Make sure that all audio connecting plugs are pushed in all the way page 9 e Make sure that the inputs and outputs of all components are connected properly e Make sure that the polarity of the speaker cables is correct and that the bare wires are in contact with the metal part of each speaker terminal page 9 e Make sure that the input source is properly selected page 12 e If the MUTE indicator blinks press the remote controller s MUTING button to ummute the A 1 VL page 12 e To use a turntable with an MC type cartridge requires a commercially available MC phono preamp page 10 e Make sure that none of the connecting cables are bent twisted or damaged Noise can be heard e Using cable ties to bundle audio cables with power cords speaker cables and so on may degrade the audio perfor mance so do not bundle cables and cords together e An audio cable may be picking up interference Try repositioning your cables Remote Controller The remote controller doesn t work e Make sure that the batteries are installed with the correct polarity page 8 e Install new batteries Don t mix different types of batteries or old and new batteries page 8 e Make sure that the remote controller is not too far away from the A 1 VL and that there s no obstruction between the remote controller and the A 1 VL s remote control sensor page 8 e Make sure that the A 1 VL is
11. e the A 1VL press the remote conitroller s MUTING button again CA Note a The Mute function is cancelled when the A 1VL is set to Off Enjoying Audio Sources Continued Using the DIRECT Function DIRECT You can use the A 1 VL as power amplifier by connecting a preamplifier 1 DIRECT Recording Unless you have the full consent of the copyright holder copyright laws prohibit using your recordings for anything other than personal enjoyment Press the DIRECT button ON The DIRECT function is enabled When connecting a preamplifier to the A 1 VL the A 1 VL will work as a power amplifier The audio signal from the component connected to the preamplifier will be output OFF The audio signal from the component connected to the A 1 VL will be output Notes e While the DIRECT function is turned on the A 1 VL works as a power amplifier and the VOLUME control of the A 1VL will not change the volume level Instead when you turn off the DIRECT function the A 1 VL outputs the audio signal at the level that its volume control is positioned Take notice the A 1VL s VOLUME control position before turning off the DIRECT function e Even when the DIRECT function is enabled the audio signal from the component selected using the input selector control will be output through the PREOUT terminal Select an input source to record Turn the Input selector control to select the component that outputs the sourc
12. e you want to record The signal from the component connected to the LINE 2 terminal cannot be recorded Prepare the recorder e Put the recorder into recording standby state e Adjusting the recording level should be performed on the recorder e See your recorder s manual for more information Start playback on the source component Start playback on the component selected in step 1 Note If you select another input source during recording the newly selected input source will be recorded 13 14 Troubleshooting If you have any trouble using your A 1 VL look for a solution in the troubleshooting section If you can t resolve the issue yourself contact your Onkyo dealer Power Can t turn on the A 1VL e Make sure that the power cord is properly plugged into the wall outlet page 11 e Unplug the power cord from the wall outlet wait five seconds or more then plug the cable in again The power is turned off and the power indicator blinks in white The amp protection circuit has been activated Remove the power cord from the wall outlet immediately and contact your Onkyo dealer Audio There s no sound or it s very soft e When you use the A 1VL as a power amplifier when the DIRECT function is turned on the sound from the component connected to the preamplifier will be output If you want to output the sound from a component connected to the A 1 VL or when you use the A 1 VL as a preamplifier use th
13. ft and right signals will be reversed and the audio will sound unnatural Front Speaker Front Speaker Right Left Caution e Do not connect speakers having impedance values of 4 ohms or lower Do not connect more than one speaker cord to indi vidual speaker terminals Connecting more than one speaker cord may cause failure e Unnecessarily long or very thin speaker cables may affect the sound quality and should be avoided e Be careful not to short the positive and negative wires Doing so may damage the A 1 VL Strip away approx 5 8 inch 15mm 15 mm of insulation from the ends of the speaker cables and CI twist the bare wires tightly as shown Twist the wire ends tightly together ce tog Unscrew the speaker terminal SS AN Gus 1 dl WS G Fully insert the bare wires Screw the terminal tight Changing the Speaker Impedance Value Setting The A 1VL allows you to set the speaker impedance values according to the speakers you use adjusting the optimum frequency characteristics against speaker loads We recommend you set the SPEAKER IMPEDANCE SELECTOR setting to 8 OHMS MIN SPEAKER for speakers having impedance of 8 ohms or higher Likewise you may want to set the setting to 4 OHMS MIN SPEAKER for speakers having impedance of 4 ohms or higher T bud 8 OHMS MIN ST
14. ion e If there is an obstacle between the remote controller and the remote control sensor the remote controller will not operate Connecting the A 1VL Before Making Any Connections e Read the manuals supplied with your components e Don t connect the power cord until you ve completed all audio and video connctions RCA Phono Connection Color Coding RCA Phono connections are usually color coded red and white Use red plugs to connect right channel audio inputs and outputs typically labeled R Use white plugs to connect left channel audio inputs and outputs typically labeled L And use yellow plugs to connect composite video inputs and outputs Analog audio Right red red Left white gt Left white e Push plugs in all the way to make good connections loose connections can cause noise or malfunctions To prevent interference keep audio and video cables away from power cords and speaker cables Connecting Your Speakers Connecting Your Speakers Connect the right channel speaker to the RIGHT speaker connector on the A 1VL and the left channel speaker to the LEFT speaker connecter Connect the connector on each speaker to the connectors on the A 1 VL and connect the connec tor on each speaker to the connectors on the A 1 VL Be sure to connect the positive and negative cables for the speakers properly If they are mixed up the le
15. le During this POWER indicator time the A 1VL does not output an audio signal Tips on sound quality You will get better sound quality 10 to 30 minutes after you turn on the A 1VL To avoid degrading the sound quality do not tie audio RCA phono cables and speaker cables together in a bundle When placing the A 1VL avoid a place where it is susceptible to vibrations Playing a Connected Component MUTING 3 A 1VL KY Remote controller 12 MUTING indicator VOLUME Select the component you want to play Turn the Input selector control to select the component you want to play CD Select to play the audio signal from the component connected to the CD terminal TUNER Select to play the audio signal from the component connected to the TUNER terminal LINE 1 Select to play the audio signal from the component connected to the LINE 1 terminal LINE 2 Select to play the audio signal from the component connected to the LINE 2 terminal PHONO Select to play the audio signal from the component connected to the PHONO terminal Start playback on the selected audio component To adjust the volume use the VOLUME conirol or the remote coniroller s VOLUME button Muting the A 1VL remote controller only With this function you can temporarily mute the output of the A 1 VL Press the remote coniroller s MUTING button The output is muted and the MUTING indicator flashes on the A 1VL MUTING To unmut
16. long periods of time Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 15 16 T7 18 Damage Requiring Service Unplug the apparatus from the wall outlet and refer servicing to qualified service personnel under the following conditions A When the power supply cord or plug is dam aged B If liquid has been spilled or objects have fallen into the apparatus C If the apparatus has been exposed to rain or water D If the apparatus does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the apparatus to its normal operation E If the apparatus has been dropped or damaged in any way and F When the apparatus exhibits a distinct change in performance this indicates a need for service Object and Liquid Entry Never push objects of any kind into the apparatus through openings as they may touch dangerous volt age points or short out parts that could result in a fire or electric shock The apparatus shall not be e
17. magnet MM type cartridges Use an analog audio cable RCA phono to connect the A 1VL s PHONO L R inputs to the audio outputs on your turntable as shown Remove the shorting pin plugs before connecting your turntable Ground wire OUTPUT Notes e If your turntable has a ground wire connect it to the GND screw on the A 1 VL With some turntables connecting the ground wire may cause hum in which case it should be disconnected e If your turntable has a moving coil MC type cartridge you ll need a commercially available MC phono preamp Connect the phono preamp to your turntable and then connect the phono preamp to the A 1VL s PHONO L R inputs Connecting the A 1VL Continued Connecting a Power Amplifier You can use the A 1VL as a preamplifier by connecting the A 1VL to a power amplifier When you use the A 1 VL as a preamplifer connect the main in terminals on the power amplifier to the PRE OUT terminals on the A 1 VL LINE IN a Note The signal from the PREOUT terminal will be output whether the DIRECT function is enabled or not Connecting a Preamp You can use the A 1 VL as a power amplifier by connecting the A 1 VL to a preamplifier When you use the A 1 VL as a power amplifier connect the pre out terminals on the preamplifier to the MAIN IN terminals on the A 1VL You can enjoy surround sound playback by connecting front left and right s
18. oisture may con dense on the lens of the optical pickup one of the most important parts inside this unit The unit is moved from a cold place to a warm place A heater is turned on or cold air from an air con ditioner is hitting the unit In the summer when this unit is moved from an air conditioned room to a hot and humid place The unit is used in a humid place e Do not use this unit when there s the possibility of mois ture condensation occurring Doing so may damage cer tain parts inside this unit If condensation does occur leave this unit turned on for two to three hours By that time the unit will have warmed up and any condensation will have evaporated To reduce the risk of condensation keep this unit connected to a wall outlet For British models Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel IMPORTANT The wires in the mains lead are coloured in accordance with the following code Blue Neutral Brown Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows The wire which is coloured blue must be connected to the ter minal which is marked with the letter N or coloured black The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red
19. peakers to the A 1 VL and connect ing center and surround speakers to the preamplifier If you have a powered subwoofer connect it to the preamplifier s PRE OUT MAIN IN CJ 000000 oO Oooo Note Before you use the A 1 VL as a power amplifier be sure to turn on the DIRECT function by pressing the DIRECT button page 13 Connecting the Power Cord Notes e Before connecting the power cord connect all of your speakers and audio components e Turning on the A 1VL may cause a momentary power surge that might interfere with other electrical equipment on the same circuit If this is a problem plug the A 1VL into a different circuit e Do not use a power cord other than the one supplied with the A 1 VL The supplied power cord is designed exclusively for use with the A 1 VL and should not be used with any other equipment e Never disconnect the power cord from the A 1VL while the other end is still plugged into a wall outlet Doing so may cause an electric shock Always disconnect the power cord from the wall outlet first and then the A 1VL 1 Connect the supplied power cord to the A 1VL s AC INLET 2 Plug the power cord into an AC wall outlet 11 Enjoying Audio Sources Turning on the A 1VL POWER PowER Press the POWER button to turn on the A 1VL M The POWER indicator lights up Note It takes about five seconds for the elec tric circuit to be stab
20. portant Safety Instructions NADU FWN 10 11 12 13 14 Use only with the cart stand Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radia tors heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are pro vided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience recepta cles and the point where they exit from the appara tus Only use attachments accessories specified by the manufacturer PORTABLE CART WARNING tripod bracket or table spec ified by the manufacturer or sold with the apparatus When a cart is used use cau tion when moving the cart apparatus combination to avoid injury from tip over ACY 83125A e Unplug this apparatus during lightning storms or when unused for
21. ries Detach the battery cover D Insert the two R6 size AA batteries Be sure to match the and ends of the batter ies to the diagram inside the battery compart ment Attach the battery cover Notes e Do not mix new batteries with old batteries Do not mix different kinds of batteries To avoid corrosion remove the batteries if the remote controller is not to be used for a long period of time e Remove dead batteries immediately to avoid damage from corrosion If the remote controller does not operate smoothly replace both batteries at the same time e The life of the batteries supplied is about six months but will vary depending on usage Using the Remote Controller Point the remote controller toward the remote control sensor Remote control sensor About 5 m 16 feet Notes e Place the unit away from strong light such as direct sunlight or inverted fluorescent light which can pre vent proper operation of the remote controller e Using another remote controller of the same type in the same room or using the unit near equipment that uses infrared rays may cause operational interference e Do not put any object such as a book on the remote controller The buttons of the remote controller may accidentally be pressed and drain the batteries e Make sure the audio rack doors do not have colored glass Placing the unit behind such doors may prevent proper remote controller operat
22. right 2004 ONKYO CORPORATION Japan All rights reserved 29343551A
23. xposed to dripping or splashing and no objects filled with liquids such as vases shall be placed on the apparatus Don t put candles or other burning objects on top of this unit Batteries Always consider the environmental issues and fol low local regulations when disposing of batteries If you install the apparatus in a built in installation such as a bookcase or rack ensure that there is ade quate ventilation Leave 20 cm 8 of free space at the top and sides and 10 cm 4 at the rear The rear edge of the shelf or board above the apparatus shall be set 10 cm 4 away from the rear panel or wall creating a flue like gap for warm air to escape Precautions Recording Copyright Unless it s for personal use only recording copyrighted material is illegal without the permission of the copyright holder AC Fuse The AC fuse inside the A 1VL is not user serviceable If you cannot turn on the A 1 VL contact your Onkyo dealer Care Occasionally you should dust the A 1VL all over with a soft cloth For stubborn stains use a soft cloth dampened with a weak solution of mild detergent and water Dry the A 1VL immediately afterwards with a clean cloth Don t use abrasive cloths thinners alcohol or other chemical solvents because they may damage the finish or remove the panel lettering Power WARNING BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME READ THE FOLLOWING SECTION CARE FULLY AC outlet voltages v
Download Pdf Manuals
Related Search