Oneida Air Systems 10 HP User's Manual
Contents
1. 6 Connect Cyclone Cone to Barrel using included Clamp Ring Seal around Clamp Ring with silicone 7 Connect 14 to 10 Reducer bottom of Cone Seal around Reducer with silicone 14 to 10 Reducer 8 Connect Sleeve Kit to Cyclone Cone and Dust Barrel Sleeve using included Band Clamps Kit For cyclonic preseparation there must be an air tight seal between cyclone and dust container Dust bin must be located vertically under cyclone Material drops down by gravity Ideas for make your own Dust Bins 55 gal drum metal or rigid plastic garbage can air tight plywood box Note You can make a lid using plywood lined with some type of gasket material Carpet Foam Continued on next page 10 HP Pulley Drive Owner s Manual O A S 2007 Vi General Assembly Instructions conr 7 Set up Fan Blower Square CAUTION Fan Outlet All moving parts must have guards to protect personnel Safety requirements vary so the number and type of guards needed to meet company local and OSHA standards must be determined and specified by the user Never start a fan without having all safety guards installed Check regularly lt lt Connect for damaged or missing guards and do not operate any fan 5 to top of with guards removed Fans can also become dangerous Cyclone because of potential windmilling even though all electrical power is disconnected Always block the rot2. 15hp 44 Belt BLZ440001 lt D Sheaves should be accordance to NEMA Spec MG 1 or as approved by the manufacturer for a specific application Adjusting 1 Loosen setscrews Y and in moving parts of sheave Turn pulley so Key E drops down amp out of the way 2 Adjust sheave pitch diameter for desired speed by opening moving parts 1 2 or full turns from closed position Do not open more than six full turns for B belts 3 Tighten setscrew Y over key and setscrew C over flat surface machined into sheave center hub Torque set screws to the following values 100 in Ibs minimum to 130 in lbs maximum 4 Put on belts after elevating motor mount plate and adjust belt tension to proper value Do not force belts over grooves 5 Future adjustments should be made by loosening the belt tension and increasing or decreasing the pitch diameter of the sheave by half or full turns as required Readjust belt tension before starting drive 6 Be sure that all keys are in place and that all setscrews are torqued properly before starting drive Check setscrews and belt tension after 24 hours of service 7 Replace shaft and pulley guards covers 6 Condensation Drain Plugs All explosion proof and totally enclosed motors are equipped with automatic drain plugs which should be kept free of oil grease paint grit and dirt The drain system is designed for normal floor feet down mounting For
3. Motors should be installed protected and fused in accordance with latest issue of National Electrical Code NEMA Standard Publication No MG2 and local codes Rotating parts such as pulleys coupling external fans and unusual shaft extensions should be permanently guarded Keep hands and clothing away from moving parts Electrical repairs should be made by trained qualified personnel only 4 Location The free flow of air around the motor should not be obstructed The motor should never be placed in a room with hazardous processes or where flammable gases or combustible material may be present unless it is specifically designed for this type of service 5 V Belt Drive A Align sheaves carefully to avoid axial thrust on motor bearing The drive sheave on the motor should be positioned toward the motor so it is as close as possible to the bearing B When adjusting belt tension make sure the motor is secured by all mounting bolts before tightening belts C Adjust belt tension to belt manufacturers recommendations Excessive tension will shorten bearing life Insufficient tension shortens bearing life can reduce fan performance and may cause vibration Belts may slip during start up but slipping should stop when fan reaches full speed Shafi Ley soihotshoave cher ae pulley has been adjusted Replacement Belt Part Numbers x 10 44 Belt 7440000 with Tange
4. A S immediately so we can expedite replacements Please check in all parts within 3 days from receiving order Notify O A S immediately of any missing or incorrect parts O A S does not accept any claims for damage or shortage after 3 days from date of delivery Limited Warranty Oneida Air Systems warrants products it manufactures for a period of 2 years to the original purchaser from the date of purchase Items not manufactured by O A S are limited to their own manufacturer s warranties This warranty does not apply to defects due directly or indirectly to misuse negligence accidents abuse repairs or alterations or lack of maintenance This is Oneida Air Systems sole written warranty and any and all warranties that may be implied by law including any merchantability or fitness for any particular purpose are hereby limited to the duration of this written warranty O A S does not warrant or represent that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants In no event shall O A S s liability under this warranty exceed the purchase price paid for the product and any legal actions brought against Oneida Air Systems shall be tried in the State of New York County of Onondaga Oneida Air Systems shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Oneida Air Systems does not
5. Blower YS External Cartridge Filter Dust Box Can be any height For efficient pre separation there must be an air tight seal between cyclone and dust bin Air Tight Dust Bins can be used as support for cyclone as well as provide large capacity dust storage Rotary Air Locks Provide an alternative to an air tight dust bin for larger volume capacity and less maintenance The airlock maintains an air tight seal which allows material to Rotary drop out into an open container Air Lock A 10 Airlock will drop 1 85 cu ft rev of material 10 HP Pulley Drive Owner s Manual O A S 2007 V Tube VI General Assembly Instructions 1 Determine mounting height for the cyclone Height depends on size of Dust Bin and length of Flex Hose to Dust Bin connection Inlet Cyclone Barrel 2 Mount Angle Iron Brackets to wall using included hardware 3 Mount Cyclone Barrel to Wall Brackets Determine inlet orientation Fasten Cyclone to Brackets with one bolt on each side Drill new Gismp hole in ring if needed for your orientation Cyclone Barrel 4 Lower V Tube into Cyclone Barrel 5 Connect Outlet Cyclone Barrel to Inlet Cyclone Barrel using included Clamp Ring Ring
6. arrow on cabinet Sticker located on backside of blower Green Chassis Screw Ground Connect house ground wire to green chassis screw in motor wire housing box To reverse rotation interchange any two power line leads 10 HP Pulley Drive Owner s Manual O A S 2007 IK Fan Blower Maintenance The Fan Blower has a TEFC totally enclosed fan cooled motor that can be placed outside The fan housing is adjustable by 22 1 2 degree increments outlet can be oriented by adjusting bolt hole locations between the scroll and the bracket assembly Fan blowers come as clockwise up blast from Oneida Air Systems G dub x x r ge B i D vTW Bi i lt TTT LIN Item A B D F G H L M N R S T V 17 1 5 12 5 8 10 1 8 14 1 2 12 1 4 34 1 8 11 91 2 22 65 8 185 18 87 8 8 91 2 um 445 321 257 368 311 867 279 241 559 168 465 225 203 241 A high pressure blower requires a certain amount of resistance which will prevent motor over amperage Make sure power source matches wire voltage configurations a Check set screw and key fan wheel make sure fan wheel is secure fan blower should not vibrate WARNING Rotating Fan Blades DANGER Keep Objects Clear of Inlet and
7. believe the devastation This type of fire is rare but worth safeguarding against The best way to avoid a wood shop fire is to keep the shop clean Ashop ankle deep in dust with layers of fine dust everywhere is an accident waiting to happen A good dust collection system reduces overall fire hazards but also adds new concerns A fire hazard is still present Combustible material is now in the dust collector and storage container The following points are worth heeding 2 t is the buyer s responsibility to follow all applicable federal state local OSHA NFPA or authorities having jurisdiction codes and regulations when installing and operating this dust collector Fire Marshalls may want the unit located outside of the building If the collector is located inside the facility controls such as spark detection suppression or explosion venting may be required Most local jurisdictions consult or adopt NFPA National Fire Protection Agency codes However other codes may apply Local codes may vary from jurisdiction to jurisdiction NFPA 664 Code book Standard for the Prevention of Fires and Explosions in Wood Processing and Woodworking Facilities applies to woodworking operations that occupy areas of more than 5 000 sq ft or to areas where dust producing equipment requires an aggregate dust collection flow rate of more than 1500 cfm Cubic Feet per Minute This exempts some small operators from the NFPA code 664 but other co
8. protection The External Filter can be cleaned using the following methods 1 Compressed air from outside Blast air along pleats of the filter at about a 20 angle Blast air out and away from you or anyone in the general area Keep air nozzle at least 6 from filter Closer blasts may damage filter material Filter must be cleaned regularly or filter damage may result 2 Empty Dust Bin Wait a few minutes for internal dust to settle then unclip and carefully empty dust bin 3 Rinse with water Optional Keep nozzle at least 6 from filter and keep your pressure down Closer blasts may damage filter material Rinse off INSIDE of filter Let filter dry completely before reuse or keep a spare filter on hand 10 HP Pulley Drive Owner s Manual O A S 2007 Rectangular Plenum attached up to 8 away 20 Air Fig MT h w to Filter Mounting Instructions 1 Mount brass static pressure tube plenum with tip pointed into the air stream Use mounting bracket and sheet metal screws if interior of plenum is not accessible Refer to drawings for location of brass static pressure tube 2 Refer to instructions provided with gauge for mounting to bracket 3 Mou
9. 10 HP NYB Pulley Belt Drive Oneida Cy el onic Air Dust Collectors Owner s Manual Loc mmm ce BORN E Oneida Air Systems Inc 1001 West Fayette St Syrac And UN Phon e 1 800 732 4065 315 476 5151 Fax 315 476 5044 1 eida Thank You for Choosing an Oneida Air Systems Product OAS manufactures and sells dust collection equipment only Our qualified technicians and sales staff are available 7 30am 6 00pm EST Mon Thur and 7 30am 5 00pm EST Fri to answer any questions concerning OAS products and dust collection Call for ductwork design and ductwork quotes including system pricing and shipping cost Read the entire Owner s Manual before installing or operating system Table of Contents VII VIII XII XIII XIV XV XVI Proudly Made in System Start Up Information Pulley Drive Configurations General Specifications amp Fan Performance Curves Dimensions Configuration Examples General Assembly Instructions External Filter Box Assembly Wire Diagram Fan Blower Maintenance Accessories Troubleshooting Fire Hazards Read Before Installin
10. Outlet Do not open until the power REMINDER Check Motor and Fan Lubrication Schedule supply has been locked off and the shaft has stopped rotating Maintenance of Fan Blower Failure to do this can result in serious injury 1 Electrical Failure to follow instructions and safe electrical procedures could result in serious injury or death Disconnect all power and discharge all capacitors before servicing Install and ground per local and national codes Consult qualified personnel with questions or if repairs are required Electrical Connections A All wiring fusing and grounding must comply with National Electrical Codes and local codes B To determine proper rotation and voltage connections refer to the wire diagram section of this manual C Use the proper size of line current protection and motor controls as required by the National Electrical Code and local codes Recommended use is 125 of full load amps as shown on the nameplate for motors with 40 degrees Celsius ambient and a service factor over 1 0 Recommended use is 115 of full load amps as shown on the nameplate for all other motors Do not use protection with larger capacities than recommended Three phase motors must have all three phases protected 10 HP Pulley Drive Owner s Manual O A S 2007 Maintenance of Fan Blower Cont 2 Cleanliness Keep both the interior and exterior of the motor free from dirt water oil and grease 3 Safety
11. amp 160z Needle Felted Polyester Slide the bottom of the filter over a five gallon plastic bucket 1 Micron Filtration Secure with a band clamp or strong bungee shock cord Be sure filter is not loose or moving around when the system B lone Part FTSO80000 is on This could lead to wear on the filter 10 long Part FTS100000 With the use of a cyclone pre separator the buckets will Note Also available with zipper not need emptying very often but do need to be checked bottoms for ceilings occasionally Simply lift the bucket the weight will indicate how full the bucket has become Note Plenum hole configuration varies The number of holes matches the number of filters 2 uc 3 o 12 12 12 lt gt lt gt 4 gt n E m C 2 C 2 Hose Clamps Part ACB120000 ir gp E C 5 gallon buckets 12 high Not supplied with j 12 mi j system Can be purchased Part No E box height i lice Use 3 8 or thicker plywood SDS050000 or recycled joint compound buckets eal plenum box with silicone or food storage containers can be used 10 HP Pulley Drive Owner s Manual O A S 2007 Fan Blower Wiring Diagram Wiring should always be done o a licensed electrician Before Operation Before making electrical power connections check for proper grounding of motor and application All electrical contact
12. ating assembly before working on any moving parts Fan Outlet Square to round transition for fan outlet does not come with installation hardware Drill holes bolt screw or pop rivet to fan outlet seal with silicone Make sure pulley cover and shaft guard are in place before operation Silencer Square 8 If applicable connect silencer to square to round to transition Round 9 Connect ductwork from fan inlet to top of Cyclone Barrel Plenum 10 Set up Plenums according to height requirements for type Instructions for Cartridge Filters Cartridge Clamp filter cartridges to plenum then clamp Filters dust bins to cartridges External Filter Cartridge Cleaning Intervals When unit is turned off use compressed air to blow dust off from exterior of filter Hold nozzle at least 8 away from filter pleats Do not remove bottom dust pan before or during the blow off process Let dust settle into dust pan Unclip and dump out dust Filter removal is not required You can also run your fingers around the filter pleats to knock material down Instructions for Tube Filters See next page Dust Bins Instructions for build your own plenum See next page 11 Connect ductwork between Fan Blower outlet or Silencer and plenum 10 HP Pulley Drive Owner s Manual O A S 2007 VII External Filter Bag Assem
13. bly a 22 gauge galv OAS Galvanized Plenum Box 1 Connect the plenum to the fan blower outlet with the bolts provided Band clamp tube filters to the Ring Thimbles on the bottom of the plenum and to the tops of the 5 gal buckets Check mounting height Match to bag heights Build your own plenum Plenum box can be constructed of plywood or metal Ring Thimble Oneida Air Systems sells 22 gauge galv plenum boxes PANI eee The filter medium is a 16 ounce polyester felt which has been singed inside to help release caked dust For the tube style filters a 12 dia ring thimble Part FAZ000000 is needed for each filter The plenum box Hose Clamps the ring thimbles are suspended above the floor at a height Part 120000 that will allow for 5 gallon plastic bucket and tube filter to fit properly underneath A well sealed plywood box will make a good plenum for air distribution through the tube filters Use plywood for the plenums Cut 12 dia holes in the bottom of the box spaced 2 3 apart so that the ring thimbles fit snugly The rings should not be able to slide through the holes Bend Ring Thimble tabs then apply duct sealant or caulk around the edge of the ring thimble Use sheet metal screws to secure Be sure to remove any sharp edges from the bucket or ring thimble that may abrade the filter Slide the filter over Tube Filters the thimble past the raised bead Secure with a band cl
14. des may apply in your jurisdiction Consult your local Fire Marshall for help Additional information can be found in NFPA Code Book 664 The customer assumes the responsibility for contacting their insurance underwriter with regard to specific application requirements of explosion venting or if additional fire protection and safety equipment may be required Do not use this product to collect other types of dust or flammable vapors a Fire or explosion may occur Never collect sparks from a bench grinder into a wood dust collector Never introduce sparks or sources of ignition into the dust collector Personnel should keep at least 20 feet away from unit Check dust bin frequently and before leaving the shop for smoldering material a Keep portable Fire Extinguishers handy The ABC type dry chemical is generally a good choice for small wood shops Additional information on portable extinguishers can be found in NFPA 10 Standard for Portable Fire Extinguishers Be especially careful with sanding units They can produce concentrations of dust in the combustible range Make certain enough air volume is at the suction point to capture all the particulate generated This high air volume will dilute the mixture below the lower limit of flammability Be careful not to generate sparks into the sanding dust Empty dust bin and clean filter often especially when sanding Don t overload woodworking equipment especially sanders Excessive fric
15. ed steel flange for mounting System Packages Include 10hp Fan Blower Made in USA NYB 224 DH Arrangement 10 10 horsepower Pulley drive with weather shaft guard TECO Westinghouse TEFC 60 Hz 10hp Motor Three Phase 230 460v 24 12A Usable on 208v 25 9 Fan Wheel Dia 22 625 3300 12 Static Pressure Optional Items Angle Iron Wall Mount Brackets Angle Iron Stand Plenum Box 10 or 14 hole ring thimble plenum box to hold Tube Filters Silencer For fan blower outlet to 13 I D will reduce noise level Magnetic Motor Starters Rotary Air Loc 10hp Fan Curves 10hp Performance Curve Filter Media Exterior Cartridge Filters 10hp 3 Cartridges 390 Sq Ft Spun Bonded Polyester BIA ZH1 487 Test Rated C Captures 99 99 of test material over 20 microns Captures 99 9 of test material between 0 2 2 0 microns 11 fpm face velocity Exterior Tube Filters 10hp 10 Tube Filters Needle Felted Media BIA ZH1 487 Test Rated G Captures 99 99 of test material over 20 microns Captures 99 5 of test material between 0 2 2 0 microns 11 fpm face velocity Dust Bins 55 Gal Steel Drum Other large dust bins available This fan has moving parts that can cause serious injury Read the installation and maintenance instructions and the AMCA Safety Practices manual before starting maintenance or operating During Operation 1 Keep body hands and objects away from the inlet outlet and oth
16. electrician Due to varying electrical codes OAS cannot specify exact wiring requirements When wiring the collector you should always hire a licensed electrician Dust Bin Options Must Order Custom Cyclone Mounting Stand 1 Multiple Drums Custom order the System Mounting Stand for multiple drums or hoppers Stand widths will vary depending on dust container 2 Hoppers Large capacity hoppers from 5 cu yd to 3 cu yd 3 16 reinforcing angle for added support 3 16 plate body is 100 continuously MIG welded on inside 3 8 rear cross brace angle not 3 16 three 3 base channel All angles are structural not formed 3 Air Locks Rotary air locks provide an alternative to an air tight dust bin for larger volume capacity and less maintenance Example A 10 air lock will drop 1 85 cu ft rev of material 4 Cone w Clean Out Optional cone with clean out plate for use with airlocks 10 HP Pulley Drive Owner s Manual O A S 2007 Troubleshooting Note If you continue to experience Unplug unit before servicing or cleaning difficulty with your collector call Oneida Motor Overheating Air Systems at 1 The motor s internal circuit breaker will trip if the motor is overheating 800 732 4065 for assistance Caused By Air leaks between the collector and dust bin The lid of the dust bin and the cyclone must be in place and sealed when operating the dust collector Make sure
17. er moving parts of the fan such as belts pulleys and shafts 2 Do not operate at excessive speeds or temperatures Before starting maintenance work Lock power supply in off position and immobilize fan wheel Fan Static Pressure In Wg 0 1000 2000 3000 4000 5000 Volume Flow Rate CFM Performance Static pressure and volume together determine a fan s performance Several factors such as Horsepower layout of ductwork and diameter of openings can affect a fan s performance 10 HP Industrial Systems Owner s Manual O A S 2007 6000 1ndu ues 7000 8000 9000 IV DIMENSIONS External Tube Filters 34 32 5 32 5 39 e 10hp 10 tube 83 lant a o A Approx 1 8 ie lt 2 Q2 o NL 29 1 8 i 5 Gal Dust Buckets Not Included They can be bought separately L 4 v N Top View Dimensions Largest Configuration 1 1 2 Flange w Bolt Holes 10 HP Pulley Drive Owner s Manual amp O A S 2007 IV DIMENSIONS External Cartridge Filters 10hp 3 filters Single Row 66 0 d A Oo i n i Ru m du Sile
18. flex hose is not torn and the hose clamps are tight Check drum lid cover should have a foam seal and be well seated Check for holes or leaks in the dust bin barrel Motor not properly wired Check wire connections Check motor rotation See wire diagram Check breaker box Make sure power supply is 220V Poor Dust Pick Up at Woodworking Machines Caused By Improper motor rotation Running backwards will reduce suction by 3096 Check length of duct runs and duct diameters compared to ductwork design guideline Make sure all ductwork is sealed Large air losses will occur even through small cracks in the ductwork Use silicone duct tape or duct mastic compound as a sealant Check for air leaks between collector and dust bin Close all unused blast gates at your woodworking machines Examine hood design for weaknesses according to the ductwork guide Check for a restricted pipe too small a hood port or too small a branch line See branch line diameter chart in ductwork guide Be sure that your filters are clean See filter cleaning directions Filters filling with large chips and excessive dust Caused By Air leakage between cyclone and dust bin Cyclone and dust bin must be air tight Even small leaks will cause poor preseparation in the cyclone Check drum for any leaks Make sure drum lid forms a good air tight seal with the drum Check flex hose connection Make sure hose clamps are tight Seal with silicone Ma
19. g System Terms and Conditions Filter Cleaning Instructions Optional Filter Efficiency Gauge Mounting Instructions Supplemental Instructions for Magnetic Motor Starters 10 HP Pulley Drive Owner s Manual O A S 2007 9 1 11 12 13 14 15 16 17 18 19 20 21 23 I System Start Up Information 1 Read the installation and maintenance instructions as well as the recommended safety practices in this manual 2 Install Ductwork completely A Seal ductwork with silicone sealant or duct tape B Have Dust Bin in place and sealed 3 Have licensed electrician wire Fan Blower according to wire diagram in this owner s manual 4 Have licensed electrician check current draw on motor with all gates open Current draw should not exceed maximum motor amperage OAS is not responsible for destroyed motors caused by improper wiring or improper installation The Dust Collector amp Fan Blower are heavy Handling and installation should always be performed by experienced and trained personnel who have experience with rotary equipment In addition to the following instructional manual care should be taken to ensure compliance with specific safety requirements mandated by federal state and local codes Do not operate Fan Blower without connecting dustbin Never operate Fan Blower without belt and shaft guard in place Keep clear of exhaust Keep hands and objects clear of inlet and outlet Warning Check amperage draw dur
20. ing operation with all blast gates open Make certain amperage is not outside operating limit indicated on motor plate If amperage is too high shut down immediately See Troubleshooting section 10 HP Pulley Drive Owner s Manual O A S 2007 Il 10hp Pulley Drive Configurations 1 No Filter Vent Outside Caution If exhaust air is vented outside you must provide make up 1 No Filter return air Flue gases carbon monoxide be drawn into the shop from furnaces water heaters or other appliances 2 External Cartridge Filters v pem e 10hp has 3 cartridges 10hp has 10 tubes J 2 rows of 5 E 3 External Tube Filters 5 gal dust buckets not included 10HP Pulley Drive Owner s Manual O A S 2007 lil General Specifications amp Fan Performance Curves Cyclone C 3500 Full welded exterior Main body cone and inlet 16 ga galv Flanged 12 dia Inlet Flanged 13 dia Outlet 80 high 14 rolled steel flange discharge 36 dia roll
21. ke sure dust bin has not over filled Dust bin should be emptied before the dust reaches top of the container Make sure clamp around cyclone is tight and sealed with silicone If there is not enough air entering system open more blast gates Minimum 4 diameter pick up at tool location Less than 4 will restrict air flow into collector and will increase filter maintenance Excessive vibration Caused By Loose mounting bolts set screws bearings or couplings Bent shaft due to mishandling or material impact Accumulation of foreign material on the fan wheel Excessive system pressure or restriction of airflow due to closed blast gates Inadequate support structure 16 16 10 HP Pulley Drive Owner s Manual O A S 2007 KII Fire Hazards Oneida Collectors are designed for WOOD DUST only Wood shaping and cutting processes generate wood chips shavings and dust These materials are considered combustible Air borne wood dust below 420 microns in size 017 of an inch in certain concentration ranges when ignited can deflagrate burn quickly An ignition source such as a spark or ember can ignite a dust mixture resulting in an expanding flame front which can cause an explosion if tightly contained A disturbance that raises a cloud of accumulated fine dust can raise additional dust clouds which can cause a series of explosions that can level an entire building Until this type of fire has been witnessed it is difficult to
22. ncer easily drops into Filter Hold filter up to Flange Plate and clamp 1 1 2 Flange w Bolt Holes 10 HP Pulley Drive Owner s Manual O A S 2007 C 3500 Cyclone Stand 55 Drum Part 577250055 Unit should be shipped with 4 3 8 16 x 1 bolts for Cyclone mount 20 3 8 16 x 1 bolts for Cross Brace mount 28 3 8 16 x 1 bolts for Triangle Brackets 48 3 8 flat Washers 48 3 8 serrated Nuts Outlet Choose Mount Holes to Orient Inlet in Desired Location Anchor Feet Securely to Floor to Prevent Tipping 10HP Pulley Drive Owner s Manual O A S 2007 Cyclone Fan Blower and filters can be placed in different locations Cyclone wall mounted with angle iron Sleeve Kit Sleeve Kit 14 for C 2500 S N cyclone requires 16 18 for a single drum and 24 for 2x drums Additional feet of flex can be purchased to make the sleeve kit longer if needed iode Cyclone Fan Blower outside Plenum inside Metal Drum T Drum Standard 55 gal steel drums are usually 35 36 high Oneida Air Said sells 55 gal and 35 gal fiber and steel barrels with metal lids and snap on 6 8 or 10 Tube Filters rings Splitter 55 gal fiber 35 5 high 22 dia 35 gal fiber 23 high 22 dia od 55 gal steel 35 5 high 22 dia Hoppers see Accessories page Fan
23. nt gauge up to 8 away mounting it closer will not affect reading r 4 Connect clear tubing from brass static pressure tube to the port labeled WV 9 INCHES W C mcam me cR ES high on the back of the pressure gauge Elbow Plenum Side View 5 Make sure the tubing is not crushed or kinked along its entire length cut shorter if necessary Air Flow Gauge Reading Instructions to Filter 1 Gauge may need to be zeroed Follow the instructions provided with pressure gauge 2 Take the initial reading with cleaned filter s and the typical number of blast gates open in normal operation 3 Always read the gauge with the same number of gates open The more gates open the higher the pressure reading on the gauge 4 When the gauge rises to 3 it s time to clean your filter s After many cleaning cycles a filter s pressure will rise after each cleaning An older filter does not get as clean as a new filter 10 HP Pulley Drive Owner s Manual O A S 2007 KVI Supplemental Instructions for Magnetic Motor Starters with Oneida Air Systems Dust Collectors Please see complete manufacturer instructions for more information This supplement is designed to aid Oneida Air Systems customers with frequently asked questions You must have this product installed by d qualified and licensed electrician Imp
24. other mounting positions modification of the drain system may be required Consult the manufacturer 7 The factory installed bearings in the motor are double shielded permanently sealed pre lubricated ball bearings without grease fittings and don t need relubrication The bearing part numbers are as follows Drive End 6309ZZ Opposite Drive End 6307ZZ If the bearings ever need replacing the motor should be taken to an EASA Electrical Apparatus Service Association certified shop to ensure proper installation 10 HP Pulley Drive Owner s Manual O A S 2007 Angle Iron Stands STZ350055 Angle Iron Cyclone Stand 572990000 Plenum Stand Bin Level Monitor Provides level sensing for dry bulk solids The monitor operates by using a 1 rpm synchronous motor to rotate a paddle When paddle rotation is impeded by material surrounding it the motor is de energized and triggers a SPDT snap switch The snap switch can be used in conjunction with a motor starter to turn equipment off or provide alarm functions Magnetic Motor Starters The 10 and 15hp pulley drive dust collectors do not come wired or with an on off switch Because of the voltage and amperage requirements of the system an industrial switch must be used OAS offers Square D Full Voltage Non Reversing across the Line Starters Nema Type 1 Enclosure with Start Stop in cover and class 10 overload Industrial switches can also be purchased through your local
25. roper installation is very dangerous and will void your warranty Follow all local amp national electrical codes when installing this product This starter can be used in single or 3 phase applications When used in 1 phase it requires a jumper wire that connects T2 and L3 See attached wiring diagram This tricks the overload into thinking it has 3 phase power This jumper must be installed by a licensed electrician The jumper is not required if you are using 3 phase power Important The gauge of the Jumper wire must match the gauge of the wire bringing power to the motor thru the Starter Start Stop Remove the blank plate and install the start Pushbutton stop pushbutton into the starter cover gt You must mount the Overload Protector to the contactor The Overload comes in the small white box It mounts to the three terminals at the bottom of the contactor See the complete instructions for more information After mounting the overload connect 2 brown wires marked 95 amp 96 to their respective numbered terminals on the overload 10 HP Pulley Drive Owner s Manual O A S 2007 gt Open access cover on the overload then set the overload amperage dial to match the FLA amperage of your motor The FLA value can be found on your motor nameplate Overload Amperage Dial Be sure you have the proper voltage available for your Starter s Power amp Control Circuit Control circuit con
26. s and connections must be properly insulated and enclosed Coupling belts chains or other mounted devices must be in proper alignment balance and secure to insure safe motor operation Electrical Wiring Prior to connecting to the power line check motorplate for proper voltage and rotation connection This motor should be installed in compliance with the National Electrical Code and any other applicable codes Voltage at motor not to exceed or 10 of nameplate voltage Licensed electrician should make all electrical connections Electrical Disconnects Every motor driven fan should have an independent disconnect switch to isolate the unit from the electrical supply It should be near the fan and must be capable of being locked by maintenance personnel while servicing the unit in accordance with OSHA procedures Always use the wire diagram on the motor plate Sometimes the wire diagrams on the motor will be for different rotation Wire for counter clockwise rotation Follow Motor Plate for wiring diagram Locate factory applied rotation arrow on blower cabinet to establish rotation direction It is not possible to know beforehand which direction a 3 phase motor will rotate Bump start the motor and observe the direction of rotation of the end of the blower shaft see hole in NYB outer cabinet that is aligned with the end of the blower shaft KK Motor Wire Box Motor should be wired per factory applied rotation
27. tional heat can spontaneously ignite dust Sparks can be generated in several ways High speed sanders and abrasive planers may strike foreign material Saws and edgers may strike foreign material and create a red hot metal fragment Knots in hardwood can create frictional sparks Tramp metal when drawn into the collector can spark against ductwork Check wood stock for old nails and screws which can create red hot metal fragments a Avoid using excessively large wood waste storage bins Always check storage bins for smoldering material before leaving for the day Electrically ground all equipment and ducting Static sparks can ignite wood dust Avoid using PVC drainpipe a Don t allow accumulation of layers of fine dust on horizontal surfaces Especially overhead lights electrical boxes and fuse panels which can ignite dust Unplug unit before servicing or cleaning 10 HP Pulley Drive Owner s Manual amp O A S 2007 Terms and Conditions Checking in Order Please look over the shipped order very carefully in the presence of the delivery person for damage or incomplete shipment before signing the delivery receipt Please note any tears or irregularities in shipping packaging however slight on the shipping delivery receipt This could be an indication of extensive concealed damage The shipping company will not take responsibility if the damage is not noted on the delivery receipt In the event of shipping damage call O
28. trols Contactor Coil in Starter Coil voltage is can be independent from the line voltage that runs your motor Customers may desire an alternative Contactor Coil voltage to connect a Starter to a low voltage control circuit Most OAS Starters are shipped with 240v coils Plug the Start Stop Push Button Assembly into keyed receptacle As shown below gt Run power to the starter and from the starter to your motor See the manufacturer instructions for more details The Power Circuit connected to the Starter should be fed from a dedicated circuit breaker or disconnect with fuses Don t connect any branch circuits to the Mag Starter Power Circuit The overcurrent protection circuit breaker or fuse for the Starter Power Circuit is to be sized per Article 430 32 of the NEC Use time delay fuses rated for motor circuits 10 HP Pulley Drive Owner s Manual O A S 2007 Circuit Breaker or disconnect here as required by code Note Select Size of Fuse or Circuit Breaker Per Article 430 32 of the NEC NFPA 70 3 only Move this Wire to L2 for Single E IT T 2 7 E KL SY t 99 09 69 69169 09 3 E 22 O 9 eo pon PM Im T1 NS Omit this Install this Jumper for Single Using the Same Gauge Wire Wire for Sized amp Connected to L1 amp L2 Single 10 HP Pulley Drive Owner s Manual amp O A S 2007
29. warrant or authorize use of wood dust collectors for other purposes This includes wood products that are treated coated or otherwise altered from their natural state Note Motors should be protected from extreme weather to prolong motor life Delivery Risk of Loss Products will be shipped to Buyer s single destination Title and risk of loss shall pass to the Buyer upon delivery to such destination Buyer pays transportation expenses Dates of shipment are advisory and O A S will make reasonable efforts to ship on or before the date states for shipment however O A S shall not incur any liability for failure to ship on that date Returned Goods Policy Buyer must inform O A S of any shortage or damage by so noting in writing on the freight delivery bill prior to signing to indicate receipt of shipment All claims including claims covered under the limited warranty are subject to inspection and investigation by O A S O A S reserves the right to inspect and investigate all returned products before Buyer s claim is settled All products returned for a cash refund must be unused and resaleable and purchased within the last six months There are no refunds on flex hose custom made components or partial kit items Kits must be returned in full all components for credit There will be a 25 restocking fee applied to any returned items 10 HP Pulley Drive Owner s Manual O A S 2007 All steps should be done with a dust mask and eye
Download Pdf Manuals
Related Search