Omega Vehicle Security 430 User's Manual
Contents
1. omega com CE OMEGA FSW 420 430 Thermal Flow Switches M 4586 1007 hop online at omega com e mail info omega com For latest product manuals omegamanial info INSTRUCTION FSW 420 430 INSTALLATION amp INSTRUCTION SHEET 1 0 Install the FSW 420 430 by inserting the MNPT threaded sensor tip into a tapped pipe or T fitting Use Pipe Tape or Plumbers Putter on NPT threads to aid in sealing Tighten firmly but do not over tighten as this could damage the NPT threads and prevent proper sealing 2 0 With provided connection cable disconnected complete unit wiring by connecting the Brown wire to 24VDC supply and the Blue wire to common The Black wire is now connected to the side of your load The side or common of your load is now also connected to ground NOTE Be sure that the common ground of the FSW 420 430 and the LOAD are the same The white wire if present is not used 3 0 Setting unit zero point With the media flow turned off depress setup button located on the front of the unit with a small instrument Screwdriver or Paper Clip and hold while connecting the pre wired cable to the unit The setup button is located on the face of the FSW 420 430 just between the Flow OK and the Overflow LED s The cable would have been pre wired in step 2 above Once the unit comes on remove the instrument from the setup button and allow the unit to go through it s zero point calibration The unit will start w2. 20 430 so as not to damage the tip of the sensor The electronics are embedded just behind the tip of the FSW 420 430 and denting or bottoming out of the tip could cause damage Maintenance is not required as the FSW 420 430 has no moving parts However should the sensor become coated after a period of time in operation due to water or media conditions simply wipe the probe tip with a soft cloth and alcohol omega com hermal Flow Switches M 4586 1007 Shop online at omega com e mail info omega com For latest product manuals omegamanital info INSTRUCTION SHEET Technical Data Flow switch FSW 420 430 insertion probe type with relative measurement Liquid Media Sensor Data Low Flow Set Point Auto set 50 Adjustable via set push button Hi Temp Set Point N A Medium Temperature 20 C to 80 C 20Cto 80C Response time Repeatability Hysteresis 10 of set point value typical Pag Pressure Mechanical Data Protection Class IP 67 NEMA 6 Material Sensor Head Stainless Steel 303 Thread VY NPT Thread Connection M12 male socket 4pin 2m cable with M12 connector and pigtail Electrical Data Operating Voltage 20 30 VDC short circuit protected Switching current lt 200mA Power Consumption 6 W max Initial Operation After 15 seconds Electrical Output PNP N O Switch closed with flow N C Switch open with flow Connection Diagram omega com C
3. EOMEGA OMEGAnet Online Service Internet e mail omega com info omega com Servicing North America Servicing Europe U S A One Omega Drive Box 4047 Czech Republic Frystatska 184 733 01 Karvin Czech Republic ISO 9001 Certified Stamford CT 06907 0047 Tel 420 0 59 6311899 Tel 203 359 1660 FAX 420 0 59 6311114 e mail info omega com e mail info omegashop cz Canada 976 Bergar Germany Austria Daimlerstrasse 26 D 75392 Deckenpfronn Germany Laval Quebec H7L 5A1 Canada Tel 49 0 7056 9398 0 Tel 514 856 6928 FAX 49 0 7056 9398 29 FAX 514 856 6886 Toll Free in Germany 0800 639 7678 e mail info omega de United Kingdom One Omega Drive River Bend Technology Centre e mail info omega ca For immediate technical or application assistance ISO 9002 Certified Northbank Irlam Manchester U S A and Canada Sales Service 1 800 826 6342 1 800 TC OMEGA M44 5BD United Kingdom Customer Service 1 800 622 2378 1 800 622 BEST Tel 44 0 161 777 6611 Engineering Service 1 800 872 9436 1 800 US A W HEN FAX 44 0 161 777 6622 Mexico En Espa ol 001 203 359 7803 Toll Free in United Kingdom 0800 488 488 FAX 001 203 359 7807 e mail sales omega co uk email espanol omega com info omega com mx It is the policy of OMEGA Engineering Inc to comply with all worldwide safety and EMC EMI regulations that apply OMEGA is constantly pursuing certification of its products to the European New Approach Directi
4. eat moisture or vibration improper specification misapplication misuse or other operating conditions outside of OMEGA s control Components in which wear is not warranted include but are not limited to contact points fuses and triacs OMEGA is pleased to offer suggestions on the use of its various products However OMEGA neither assumes responsibility for any omissions or errors nor assumes liability for any damages that result from the use of its products in accordance with information provided by OMEGA either verbal or wntten OMEGA warrants only that the parts manufactured by the company will be as specified and free of defects OMEGA MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY KIND WHATSOEVER EXPRESSED OR IMPLIED EXCEPT THAT OF TITLE AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED LIMITATION OF LIABILITY The remedies of purchaser set forth herein are exclusive and the total liability of OMEGA with respect to this order whether based on contract warranty negligence indemnification strict liability or otherwise shall not exceed the purchase prce of the component upon which liability ts based In no event shall OMEGA be liable for consequential incidental or special damages CONDITIONS Equipment sold by OMEGA is not intended to be used nor shall it be used 1 as a Basic Component under 10 CFR 21 NRC used in or with any nuclear installa
5. ith the far right LED and increment to the left Once finished all LED s should be off except for the blinking set point indicator 4 0 Setting unit range Turn on your flow and allow the flow to reach full normal flow rate Then with the setup instrument used in step 3 0 above depress the set range button on the face of the FSW 420 430 located just between the Flow OK and Overflow LED s Hold for 5 6 seconds and the FSW 420 430 will range itself to the full flow rate or 5 ft second whichever is less this process could take 45 60 seconds All of the 7 LED s will flash when auto scaling is complete and the Set Point LED will begin to flash default is set for 50 The Green Flow OK LED will come on when the flow rate goes above the set point and the output signal of the unit will change states 5 0 Should you wish to set the set point at a different LED setting or rage of flow simply depress the set range button repeatedly inshore intervals and the set point will change clockwise to any LED you wish to choose When the correct LED is flashing your new Set point is established 6 0 The Over Range light Offset RED LED will come on if your already established full flow rate were to increase If you wish to rescale to the new flow rate simply depress the set button again as you did in Step 3 0 and reset your set point if desired using the same procedure as in item 4 0 above See additional notes NOTE Use caution while installing the FSW 4
6. ructions and or specific problems relative to the product 3 Repair instructions and or specific problems relative to the product OMEGA s policy is to make running changes not model changes whenever an improvement is possible This affords our customers the latest in technology and engineering OMEGA is a registered trademark of OMEGA ENGINEERING INC Copyright 2007 OMEGA ENGINEERING INC All rights reserved This document may not be copied photocopied reproduced translated or reduced to any electronic medium or machine readable form in whole or in part without the prior written consent of OMEGA ENGINEERING INC
7. tion or activity or 2 in medical applications or used on humans Should any Product s be used in or with any nuclear installation or activity medical application used on humans or misused in any way OMEGA assumes no responsibility as set forth in our basic WARRANTY DISCLAIMER language and additionally purchaser will indemnify OMEGA and hold OMEGA harmless from any liability or damage whatsoever arising out of the use of the Product s in such a manner RETURN REQUESTS INQUIRIES Direct all warranty and repair requests inquiries to the OMEGA Customer Service Department BEFORE RETURNING ANY PRODUCT S TO OMEGA PURCHASER MUST OBTAIN AN AUTHORIZED RETURN AR NUMBER FROM OMEGA S CUSTOMER SERVICE DEPARTMENT IN ORDER TO AVOID PROCESSING DELAYS The assigned AR number should then be marked on the outside of the return package and on any correspondence The purchaser is responsible for shipping charges freight Insurance and proper packaging to prevent breakage in transit FOR WARRANTY RETURNS please have the following information FOR NON WARRANTY REPAIRS consult OMEGA for current repair charges available BEFORE contacting OMEGA Have the following information available BEFORE contacting OMEGA 1 Purchase Order number under which the product was PURCHASED 1 Purchase Order number to cover the COST of the repair 2 Model and serial number of the product under warranty and 2 Model and serial number of the product and 3 Repair inst
8. ves OMEGA will add the CE mark to every appropriate device upon certification The information contained in this document is believed to be correct but OMEGA accepts no liability for any errors it contains and reserves the right to alter specifications without notice WARNING These products are not designed for use in and should not be used for human applications WARRANTY DISCLAIMER OMEGA ENGINEERING INC warrants this unit to be free of defects in materials and workmanship for a period of 13 months from date of purchase OMEGA s WARRANTY adds an additional one 1 month grace period to the normal one 1 year product warranty to cover handling and shipping time This ensures that OMEGA s customers receive maximum coverage on each product If the unit malfunctions it must be returned to the factory for evaluation OMEGA s Customer Service Department will issue an Authorized Return AR number immediately upon phone or written request Upon examination by OMEGA if the unit is found to be defective it will be repaired or replaced at no charge OMEGA s WARRANTY does not apply to defects resulting from any action of the purchaser including but not limited to mishandling improper interfacing operation outside of design limits improper repair or unauthorized modification This WARRANTY is VOID if the unit shows evidence of having been tampered with or shows evidence of having been damaged as a result of excessive corrosion or current h
Download Pdf Manuals
Related Search