North Star 109160 User's Manual
Contents
1. ie 2 amp 4 Proven Performance SEMI TRASH PUMPS F ITEM S 109160 109170 109180 M109160A OWNER S MANUAL Thank you for purchasing a NorthStar Semi Trash Series water pump Your machine is designed for long life dependability and the top performance you demand Please take time now to read through this manual so you can better understand the machine s operation maintenance and safety precautions Everyone who operates this water pump must read and understand this manual The time you take now will prolong your water pump s life and prepare you for its safe operation Enjoy the exceptional performance of your Mustang Semi Trash Series water pump THIS PUMP CAN PASS UP TO 1 3 SOLIDS DANGER indicates an imminently hazardous situation which if not avoided will result in death or serious injury This signal word is to be limited to the most extreme situations WARNING indicates a potentially hazardous situation which if not avoided could result in death or serious injury CAUTION indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury It may also be used to alert against unsafe practices 1 Before starting the pumps follow all of the instructions in this manual and any supplemental instructions supplied with the pump 2 Any person operating this pump and it s power unit should be fully aware of it s safe operation before they star2. end of each use is advised some liquids being pumped may leave a solid or sticky residue This may shorten the life of your pump Pump Fails To Prime 1 Clogged suction hose straine Straighten suction and dischi Replace Impeller SUCTION amp DISCHARGE SIZE SUCTION HEAD MAXIMUM DISCHARGE HEAD PRESSURE MAXIMUM FLOW PASSABLE SIZE MECHANICAL SEAL 11376 GPH gos SILICON CARBIDE TOTAL HEAD FT SUCTION amp DISCHARGE SIZE JMSUCTIONHEAD MAXIMUM DISCHARGE HEAD M PRESSURE MAXIMUM FLOW 16200 09000 PASSABLE SOLID SIZE 0 35 MECHANICAL SEAL SILICON CARBIDE TOTAL HEAD FT FLOW GPH 3 109170 ITEM PARTS D RIPTION QT ___ _ ______ 12755 Pump casing T ic 1 2 1 3 5 12076 Suction fange __
3. erly support it so as to eliminate stresses on the pump Do not run the pump dry Always fill the pump body with water before starting It is not necessary to drain the pump body after each use unless there is danger of freezing settling of solids or crystallization Do not subject pump to extreme conditions of acidity or basicity Consult factory for specific recommendations concerning chemicals and temperatures Only use original spare parts 1 suction strainer should be attached to the suction hose or pipe suction strainer has holes slots small enough to prevent large debris from working through and damaging the pump Keep the strainer clean If possible suspend the strainer to keep it working into sediment Prepare of large stones on which the strainer will rest B Tie the strainer inside a basket or pail 2 Fill the engine crankcase with oil as specified in the engine manual 3 Fill the engine with fuel see engine manual 4 Fill the pump with water utilizing the priming port on the top of the pump The pump self primes only when it is first filled with priming water WARNING this pump is designed to pump water only Never use the pump to pump flammable liquids 5 All hoses and pipe connections must be airtight 6 Place the pump in a location as near to the liquid surface as possible this will ensure proper pump suction NOTE 26ft is the maximum he
4. ight the pump can draw to 7 All hoses must be kept as straight as possible avoid sharp bends v 1 Starting Engine See Engine Manual 2 Priming Using the port on the top of the pump completely fill the pump chamber with water before starting the engine Priming Plug Drain Plug 3 Throttle Control When operating the pump when the pump is higher than the water surface you may need to speed up the engine speed When the pump is near the water surface a slower engine speed can be used This will save engine fuel and 4 Check Valve If the discharge line runs vertical for more than 9 meters It is suggested to install a check valve near the discharge port of the pump If this is done it may be necessary to vent the top of the pump so that air can be expelled during automatic repriming This air bleed may be accomplished by providing 1 4 5 cm line from the top of the pump back to the liquid source We will not assume any responsibility for damage to the pump if no check valve is used in the discharge line 5 Never allow a vehicle to run over the flexible hose This sudden shut off pressure can cause hydraulic shock If your flexible hose must be laid across a high traffic area it is advised to protect it with planking 6 Freezing water can be extremely dangerous to the pump always drain the water from the pump if freezing temperatures are a factor 7 Flushing out the pump at the
5. t using it 3 Never use these pumps for pumping flammable liquids such as diesel or gasoline 4 Never operate an engine driven unit in an explosive atmosphere near combustible materials or where insufficient ventilation exist unless specific provisions have been made regarding the power unit so as to prevent possible injury and damage Be certain the power unit is safe for the area in which it is to be operated 5 Always be sure the unit is on a secure footing Keep the immediate pump area free of all unauthorized personnel If the pump is sitting beside a pit be sure it is well anchored so that it does not fall in 10 11 12 13 14 Never operate the unit with any guards removed Do not over tighten the drain or filler plugs Excessive force may damage the threads or the pump body With engine driven pumps A Observe all safety precautions for the handling of fuel B Never refuel the engine while running C Never refuel a hot engine D Run engine only in well ventilated areas Before working on this pump make sure the power unit cannot inadvertently be started Be sure the power unit pump wiring and piping installations are suitable for the liquids being pumped and comply with all applicable codes and regulations Use at least 12 300 MM of flexible hose to make plumbing connections to the pump body Rigid piping may put stresses on the pump causing damage If rigid piping must be used prop
Download Pdf Manuals
Related Search