Nikon 9350 User's Manual
Contents
1. 4 1 Information in the Viewfinder Flashing No Lens the Canon XL Camcorder No Power Using 9350BRAC Adapters No Power Using the Pocket Scope adapter No Power Using the 9350BBA C adapter Problems Using the 200mm Catadioptric Lens on a Canon EOS Camera Non uniform Image Dark Spots in Image 4 2 Nikon cameras operated in the manual mode only will provide accurate exposure information Canon EOS camera operated in the manual mode will provide accurate exposure information Nikon cameras using the 200mm Electrophysics lens will provide no information in the viewfinder Canon XL camcorders provide complete information in the viewfinder regardless of the operating mode Check to make sure the 16x lens is securely attached to the 9350FL A the 9350BBA is securely attached to the camcorder and a CIU is properly installed inside the adapter pair The 9350EPS requires two AAA batteries to power the CIU If the batteries are dead you will not see the green image in the viewfinder The camcorder must be turned on as well The 9350 requires two AAA batteries to power the CIU If the batteries are dead you will not see the green image in the eyepiece The 9350BB A C requires a power source of 3 12 volts to operate You will not see the green image if the power connection is not made You must use the special EOS N Back Body Adapter when using a Canon EOS camera Set the camera to f 1 8 t2. Turn the camera lens ring until the object is in crisp sharp focus Only focus with the objective lens for crisp and sharp images NOTE It is always best to select an objective lens that produces the desired magnification Zooming with the camcorder objective lens will result in grainy low contrast images 2 15 2 16 2 3 C Mount Camera Operation i D This section describes the configuration set up and operation of the AstroScope Night Vision C Mount Cameras 2 17 2 3 1 Required Components The adapter pair for C Mount Cameras is pictured below Handle each part carefully If any of the optics becomes dirty refer to the Maintenance section of this manual for cleaning instructions 9350BBA C The rear module consisting of a 1 C Mount thread detachable power cable and plug cap 9350FLA C This is the C Mount device into which the objective lens is threaded to 2 3 2 Assembly l The FLA C has an alignment pin on the inside wall Align the pin with the groove on the side of the CIU and slide the CIU into the FLA C Groove in CIU Alignment Pin 2 18 2 Thereisa silver alignment pin on the inside of the BBA C Align this pin with the hole in the CIU and thread the BBA C to the FLA C Silver Alignment Pin Hole in CIU 3 Attach the assembly to your c mount camera 4 Attach an objective lens to the front of the assembly 5 Power the unit through the cable provided with 3
3. 4 2 12 AE ia 2 5 2 1 3 Notes on Optimal USE ee 2 6 2 2 Non Removable Lens Camcorder Operation 2 11 2 2 1 Required Components e rere een es 2 12 2 13 2 2 3 Notes on Optimal Use eii eei ea 2 14 2 3 C Mount Camera Operation esses 2 17 2 3 1 Required Re EE 2 18 2 915 t ud 2 18 2 4 Pocket Scope O Peras 2 21 2 4 1 Required Components ae todo net S Reds 2 22 242 ee oss Uv eo AR AM ecce E end 2 23 ASTROSCOPE ACCESSORIES SET UP AND 3 3 1 200 mm Low Light Telephoto Lens 3 3 3 1 1 Required ETH 3 4 32 12 Assembly N 3 5 3 1 3 Notes on Optimal Use eee e ed ot t eet 3 8 TROUBLESHOOTING GUIDE as ua ae 4 1 MAINTENANCE Vase elle 5 1 3 1 Key Operational Parameters 25 samen a 5 A A 5 1 321 2 Environmental sere i A 5 72 ACA RETE 5 1 WARRANTS odos aida 6 1 6 1 HOW TO RETURN PRODUCTS FOR WARRANTY REPAIR 6 1 6 2 HOW TO RETURN PRODUCTS FOR OUT OF WARRANTY REPAIR seele 6 2 111 1 INTRODUCTION TO ASTROSCOPE NIGHT VISION 1 1 Purpose of This Manual This manual provides basic information and instructions for operating the AstroScope 9350 products as well as procedures for troubleshooting We suggest that you read this manual carefully and retain the manual for future reference 1 1 1 How This Guide Is Organized Important Safeguards Precautions to take before using the equipment How Int
4. 5 Because the image is inverted a fiber optic twister is used to rotate the image 180 6 A special relay optic focuses the image properly to match the image plane requirements of video and 35mm SLR cameras Image intensifiers exhibit several key features designed to optimize their use as follows Automatic Brightness Control ABC An electronic feature that automatically reduces voltages to the MCP to keep the image intensifier s brightness within optimal limits and protect the image intensifier The effect of this can be seen when rapidly changing from low light to high light conditions the image gets brighter and then after a momentary delay suddenly dims to a constant level Bright Source Protection BSP An electronic function that reduces the voltage to the photocathode when the image intensifier is exposed to bright light sources such as room lights or car lights It protects the image intensifier from damage and enhances its life Equivalent Background Illumination EBI This describes the amount of light you see from the output of the image intensifier when there is no light input It increases with increasing temperature EBI is measured in lumens per square centimeters and determines the light level which equals the image intensifier s noise level Below this light level objects will be masked by EBI The lower value of EBI the better 1 6 1 5 Evolution of Image Intensifiers The image intensifier tube has evol
5. Alignment Pin 3 1 3 Notes on Optimal Use 3 1 3 1 Nikon The AstroScope 200mm Catadioptric Lens has a fixed aperture of F1 3 Since there is no electronic communication between the camera and lens the camera s automatic settings cannot be used However the CIU includes an internal automatic gain control feature so that a constant light output is maintained from the intensifier for most light levels Consequently we recommend adjusting the Nikon camera settings as follows 1 Set the ISO to 1000 or higher When using photographic film use high speed film only ISO1000 minimum 2 Set the camera to Manual Exposure mode 3 Setthe shutter to 1 30 second as a minimum speed 3 8 4 Focus the objective lens as needed to optimize the image sharpness 3 1 3 2 Canon EOS The AstroScope 200mm Catadioptric lens has no aperture It is permanently fixed at f 1 3 Since the camera has no electronic communication with this lens you must manually set the camera s electronics to f 1 8 to attain correct exposure metering Install the 200mm Catadioptric Lens with EOS N onto the camera 2 Set the ISO to 1000 or higher 3 Set the camera to Manual Exposure mode 4 Set the aperture to f 1 8 5 Setthe shutter to 1 30 as a minimum speed 6 Use the camera s metering to attain the correct exposure 1 Focus the lens as needed 3 1 3 3 9350 Bracket Series Install the 200mm Catadioptric lens directly onto the EPA along
6. as this is the slowest shutter speed you can hand hold the camera This can be adjusted to a faster shutter speed if directed by the camera s meter Using the camera s meter you can adjust the shutter speed as required for a perfect exposure In extreme low light conditions you may want to adjust the exposure compensation to a 2 stop Use on Canon Digital Cameras Note To prevent the camera from making any noise flashing and illuminating the LCD panel it is suggested to set the camera as follows p va 2 6 Turn the dial on the top left to the position Press the Menu button once Red eye On Off Set to Off Set to 0 ISO Set to a minimum of 1000 Beep Set to Off E leue cd e 11 Review Set to Off File numbering Set to Continuous Video system Set to NTSC Custom Function C Fn a Press the center button On the Canon D30 scroll down to number 5 and press the button again Set to Off and press the button a third time Press the Menu button twice and the display will turn off b Night time exposure On the Canon D60 scroll to number 5 and press the button again Set to 1 It will not emit Fire Press the button a third time press the Menu button twice and the display will turn off To increase the ISO setting on the D60 with the camera in manual mode press and hold the button on the u
7. for return Date and place of purchase Installation date Returned unit serial number Description of problem Return Authorization Number 6 2 HOW TO RETURN PRODUCTS FOR OUT OF WARRANTY REPAIR 7 MO OW gt Following expiration of the warranty period the owner is financially obligated to pay for any repairs which are required The owner may either return their product to their dealer and the dealer will take care of it or they may work with Electrophysics directly If you choose to deal directly with Electrophysics you may contact us through the phone number and address provided on the contact sheet at the end of this booklet You are required to provide the following information 1 Model and serial number of product 2 Your shipping address 3 Your billing address if different 4 Your fax and telephone numbers 5 Description of the failure 6 Name of the point of contact You will be asked for payment of an evaluation fee prior to beginning work Following evaluation when the extent of the repairs is known someone will contact you and estimate the total cost of the repair If you choose not to have the repair completed you will still be liable for the evaluation fee If you choose to authorize the repair the equipment will be repaired and returned following receipt of payment 6 2 7 CONTACT SHEET FOR REPAIRS AND SERVICE Electrophysics Corporation 373 Route 46 West Fairfield New Jersey 07004 USA Toll Fr
8. to 15 volts DC The wire with the white stripe is positive 6 Set the focus on the objective lens to a subject 15 feet 5 meters away While looking at a monitor loosen the back focus lens locking screw to adjust the white plastic focus wheel on the BBA C housing until the best image is obtained This operation may need to be repeated to get the best image Re tighten the lens locking screw after satisfactory focus 1s obtained 7 Thereafter only the objective lens needs refocusing to accommodate objects at different distances 2 9 8 If desired attach the plug protective cap to prevent inadvertent removal of the power plug from the unit 9 f you wish to reorient the 9350BBA C with the tripod mount at the bottom and the focus wheel on top simply loosen knurled thumb screw located at the back side of the chassis and rotate the 9350 assembly with respect to video camera to the desired position Locking Screw Focus Push to remove Shown without plug cap 2 20 2 4 Pocket Scope Operation ge This section describes the configuration set up and operation the AstroScope Night Vision Pocket Scope 2 21 2 4 1 Required Components Below is a list of items included with the unit Handle each part carefully If any of the optics becomes dirty refer to the Maintenance section of this manual for cleaning instructions 9350EPA 9350FLA C Eyepiece 2 22 2 4 2 Assembly 1 Loosen battery door rel
9. up Electrophysics See the Light WWW ELECTROPHYSICS COM 373 Route 46 West Building E Fairfield NJ 07004 P 973 882 0211 973 882 0997 OPERATING MANUAL ASTROSCOPE NIGHT VISION Export limitations Because the AstroScope 9350 modules utilize state of the art image intensifier technology it is unlawful to carry these devices out of the country or to export them without an approved U S State Department export license WARNING TO REDUCE RISK OF FIRE ELECTRIC SHOCK OR DAMAGE DO NOT EXPOSE THIS PRODUCT TO CONTINUOUS RAIN OR MOISTURE TO REDUCE RISK OF SHOCK AND TO REDUCE ANNOYING INTERFERENCE USE ONLY RECOMMENDED ACCESSORIES CAUTION DO NOT REMOVE THE COVER THERE ARE NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL EC PN 080526 REV C February 2004 Nn TABLE OF CONTENT INTRODUCTION TO ASTROSCOPE NIGHT VISION 1 1 1 1 Purpose of This Manual o a e all on 1 1 1 1 1 How This Guide Is Organized eese 1 1 1 2 Important Safeguards a ea Sh SC e Bea 1 1 1 3 Reference Cuide dias 1 3 1 4 How Image Intensifiers Work 1 5 1 5 Evolution of Image Intensifiers seen 1 7 1 6 Benefits of AstroScope Night Vision 1 7 ASTROSCOPE CONFIGURATION SET UP AND OPERATION 2 1 2 1 Removable Lens Camera and Camcorder Operation 2 3 2 1 1 Required Components 2
10. which have made it possible to increase further the unit s sensitivity improve signal to noise and contrast performance and reduce blooming due to viewing bright sources 1 6 Benefits of AstroScope Night Vision The AstroScope Night Vision System is a modular system incorporating a common module approach in which the image intensifier is integrated into an assembly consisting of a front lens adapter and a back body adapter The AstroScope System delivers several important benefits over other night vision systems These include Optimized Performance Because of the modular design and the accessibility to the image intensifier optical adapters and interfaces can be designed so that each configuration delivers optimized performance This is due to the accessibility to the photo cathode as well as the phosphor image output Seamless Integration into Daylight Imaging Systems The AstroScope s component interfaces are both electrical where electrical contacts connect components and mechanical This results in a seamless integration with daylight imaging systems As 1 7 result surveillance operatives that have been trained with daylight imaging equipment may insert an optimally configured night vision module into the daylight lens camera system and operate the equipment in virtually the identical fashion at night as compared to the day Reduced Technology Obsolescence Because of the AstroScope s modular design this night v
11. with the CIU 2 Focus the lens as needed 3 1 3 4 Canon XL 1S The Canon XL 1S camcorder can use the 200mm Catadioptric lens The EOS N adapter is required along with the Canon XL EOS Adapter The AstroScope XL pair is not used 1 Remove the Canon 16x zoom lens from the camcorder 2 Install the Canon XL EOS adapter on to the camcorder 3 Install the EOS N adapter on to the 200mm Lens along with a CIU Secure the Lens and EOS N to the XL EOS adapter Set the camcorder to Manual Exposure mode Set the aperture to f 1 6 Set the shutter speed to 1 30 second Focus the Lens as needed SE UN 3 1 3 5 9350BBA C Relay Lens Adapter Install the 200mm Catadioptric Lens directly onto the BBA C along with a CIU 2 Focus the lens as needed 3 1 3 6 9350 Pocket Scope Install the 200mm Catadioptric Lens directly onto the EPA along with a CIU 2 Turn the EPA on 3 Focus the lens as needed 3 0 4 TROUBLESHOOTING GUIDE Vignetted Images Image is out of Focus Image is too Dark Auto Focus Not Operating Using 35mm Nikon or Canon film cameras it is normal for some vignetting to occur on the left and right side of the image Using Nikon or Canon Digital cameras having a sensor size of 5 Meg or larger can expect some vignetting Smaller sensors will produce full frame imaging Using Sony and other non removable lens cameras will experience a vignetted image when the camcorder zoom is at its widest p
12. Nikon Components 9350NIK BBA side for Nikon Cameras 9350NIK FLA side for Nikon Cameras 2 1 1 2 Canon EOS Components 9350EOS BBA for Canon Cameras 9350EOS FLA for Canon Cameras 2 4 2 1 1 3 Canon XL Components 9350XL BBA for Canon XL Camcorders 9350XL FLA for Canon XL Camcorders 2 1 2 Assembly The Front Lens Adapter FLA has an alignment pin on the inside wall Align the pin with the groove on the side of the CIU and slide the CIU into the FLA Alignment Pin Groove in CIU 2 5 The Back Body Adapter BBA has a silver alignment pin on the inside Align this pin with the hole in the CIU and thread the BBA to the FLA 2 1 3 2 1 3 1 l 2 1 3 2 Silver Alignment Pin Hole in CIU Notes on Optimal Use Use on Nikon Digital Cameras In the Shooting Menu select and set the ISO to 1600 or a comparable fast ISO setting Some cameras limit the ISO to 800 while others allow up to 6400 In the Custom Functions menu select ISO Auto and turn it off In the Custom Functions select AF Assist and turn it off This will prevent the focus assist light from turning on and helping the camera focus or give your position away The camera should be set in a Manual Exposure Mode not Aperture Shutter or Program mode The lens iris should be set to its widest open position f 1 4 as an example The shutter speed should start off at 1 30 of a second
13. al Cameras 200mm Lens see pg 3 1 ES am ls Canon XL Pair see pg 2 3 200mm Lens see pg 3 1 1 3 Bracket Series see pg 2 11 ag 0350 Bracket Series 200mm Lens see pg 3 1 BBA C Adapter see pg 2 17 1 200mm Lens see pg 3 1 C Mount Video Cameras Pocket Scope see pg 2 21 g ua Eye Piece a Adapter 200mm Lens see pg 3 1 1 4 LA How Image Intensifiers Work Image intensifiers are predominant in night vision applications due to their ability to amplify low light scenes at night making them visible to the human eye and commercial cameras and camcorders Unlike thermal images image intensifiers can be used to read vehicle license tags and registration markings on boats and aircraft as well as to recognize faces which can be entered as evidence in criminal prosecutions The sequence to image formation in an image intensifier is as follows light is converted to electrons then converted back to light making intensifiers very simple devices featuring very high resolution and extremely low power consumption Photons Electrons Photons Unenhanced Image NVD Image Photo Cathode Microchannel Phosphor Plate Screen A night vision system based on an image intensifier operates as follows 1 The very dim light reflected by scenes at night lower than 0 1 lux is focused by an objective lens onto a highly sensitive 1 5 photocath
14. al diagram Close the door and secure the Battery Door release Battery Door release 2 The FLA C has an alignment pin on the inside wall Align the pin with the groove on the side of the CIU and slide the CIU into the FLA C Alignment Pin Groove in CIU 3 The 9350EPA has a silver alignment pin on the inside Align this pin with the hole in the CIU and thread it to the 9350FLA C Hole in CIU Silver Alignment Pin 2 13 En Thread the 9350 Camcorder Coupler to the back of the 9350 Loosely thread the 9350EPA to the Bracket using the threaded screw on the platform so that the EPA can slide back and forth Loosely thread the Camcorder to the Bracket using the other threaded screw Slide the EPA back and thread the Camcorder Coupler to the front of the Camcorder Tighten both threaded screws to secure the EPA and the Camcorder Secure the Objective Lens to the FLA C 2 2 3 2 14 Notes on Optimal Use To activate the unit turn the power switch on the 9350EPA to the position Turn the camcorder on Using the camcorder s zoom feature zoom to the appropriate position so that the unit does not vignette resulting in a crisp full frame image without a circle Do not zoom past that point or the image quality will be reduced To set the focus turn the camera to manual focus Look at a subject approximately 15 feet 5 meters away and set the objective lens to that distance
15. ch to manual focus The auto focus cameras available today use a variance of contrast to attain sharp focus At low light levels contrast is not typically high enough for the auto focus to operate effectively therefore manual focus generally is faster and more accurate The camera should be set in the manual exposure mode Adjust the lens to its widest aperture e g f 1 4 Adjust the shutter speed to 1 30 second as this is the minimum speed you can hand hold the camera 6 Using the camera s metering system adjust the shutter speed to attain a correct exposure Note All EOS and only Nikon Auto S brand lenses may auto focus with the AstroScope if there is enough light 2 9 2 10 2 2 Non Removable Lens Camcorder Operation This section describes the configuration set up and operation of AstroScope Night Vision on non removable lens camcorders 2 2 1 Required Components Below is a list of items included when you purchase a non removable lens night vision camcorder Handle each part carefully If any of the optics become dirty refer to the Maintenance section of this manual for cleaning instructions 9350EPA 9350FLA C 9350 Bracket Actual Bracket may vary depending on camcorder 9350 Camcorder Coupler Actual Coupler may vary depending on camcorder 2 12 2 2 2 Assembly 1 Loosen the battery door release to open the door Insert two AAA batteries into the EPA oriented as shown on the intern
16. corder on to the M Manual mode Turn the Neutral Density filter on the lens Off Set the white balance in the auto position Adjust the aperture iris to f 1 6 As you zoom the aperture will move to f 2 6 You will have to readjust the iris when you zoom out Adjust the shutter speed to either 1 30 or 1 60 second 2 7 The XL 1 has a maximum gain of 1246 and the XL 1S has a maximum of 3046 As you increase the gain the image quality decreases Try and limit the gain to no more than 6db on the XL 1 and between 12 18db on the XL 1S See the Canon operating instructions 2 1 3 3 1 EOS to XL Adapter You can use the full line of Canon EOS lenses on the Canon XL 1S Camcorder with the use of the Canon XL EOS Adapter There is a magnification increase of 7 2x the focal length of the EOS lens for example a 400mm EOS lens translates to a 2880mm lens on the XL 1S You can use the XL EOS Adapter with the AstroScope night vision system ONLY with the 9350EOS Pair The 9350XL Pair will not function in conjunction with the XL EOS Adapter 2 1 3 4 l 2 8 Canon XL EOS Adapter Use on Film Cameras Select a fast film with an ISO of at least 1000 The user can decide on black amp white or color film as both will provide excellent imaging Black amp white films have greater latitude and will produce a higher contrast image Color films will provide the green images Turn the auto focus swit
17. e it so that the lens can be stored in a compact form 2 Toremove the hood twist counter clockwise to unlock Slide hood off to remove 3 5 3 Reverse the hood and align the pins with the slots in the lens Twist clockwise to lock in place 3 1 2 1 Using the Tripod Mount Note The Tripod Mount is only required when using a tripod The tripod mount is not used on units that include the 9350EPA which already have an integral tripod mount The Tripod Mount has a flange on the inner part of the Clamping mount 3 6 2 Install the Tripod Mount onto the back of the lens so that it touches the flange Secure by tightening the knob screw 3 Secure the Tripod Mount to the tripod using one of the three holes on the bottom until the system is balanced The Tripod Mount base can be reversed if necessary to balance a heavy camera system as follows Remove the three screws from the bottom and rotate the base 180 Secure the three screws back to the base and re secure the Tripod Mount to the 200mm Lens 3 1 2 2 Installing the CIU 1 There is an alignment pin on the inside of the back end of the 200mm lens Align groove in the side of the CIU with the pin and slide the CIU into the 200mm Lens Groove in CIU Alignment Pin 2 There is a silver alignment pin on the inside of the back body adapter Align this pin with the hole in the CIU and secure the BBA to the 200mm Lens Hole in CIU Silver
18. ease to open the door Insert two AAA batteries into the EPA oriented as shown on the internal diagram Close the door and secure the Battery Door release Battery Door release 2 The FLA C has an alignment pin on the inside wall Align the pin with the groove on the side of the CIU and slide the CIU into the FLA C Groove in CIU Alignment Pin 3 The 9350EPA has a silver alignment pin on the inside Align this pin with the hole in the CIU and thread it to the FLA C Hole in CIU Silver Alignment Pin 2 23 4 Thread the Eyepiece to the back of the 9350 about half way 5 Thread the Objective Lens to the FLA C 6 Power the unit by turning the switch on the 9350EPA to the On position 7 Set the lens at infinity and adjust the eyepiece for your vision 2 24 2 25 3 ASTROSCOPE ACCESSORIES SET UP AND OPERATION 3 3 2 3 1 200 mm Low Light Telephoto Lens nodi bl 3 3 3 1 1 Required Components Below is a list of items included with the unit Handle each part carefully If any of the optics become dirty refer to the Maintenance section of this manual for cleaning instructions 200mm Lens 200mm Lens Hood Tripod Mount 3 4 9350BBA EOS N Supplied only when the EOS model is ordered 3 1 2 Assembly 1 200mm Catadioptric Lens is shipped with the lens hood in the stowed position Note The hood has a bayonet design which allows you to remove it and revers
19. ee Telephone 800 759 9577 Telephone 973 882 0211 Fax 973 882 0997 E mail service O electrophysics com 7 1
20. ensifiers Work and the Benefits of the 9350 Overview of how Intensifiers operate along with night vision advancements and advantages of the 9350 units Set Up and Operation Description of how to prepare the 9350 unit for use including camera and exposure settings Troubleshooting Solutions to common problems Maintenance Information on how to clean and store the 9350 units Product Specification Information on current draw and environmental specs Night Vision Terminology A glossary of the basic terms used when dealing with night vision Additional Information Includes warranty and contact information for repairs and service 1 2 Important Safeguards Read Instructions safety and operating instructions should be read before the product is operated Keep the instruction manual for future reference 2 Heed Warnings Adhere to all warnings on the product and in the operating instructions 3 Servicing Do not dismantle or otherwise attempt to service this product or any of the accessories yourself Refer all servicing to Electrophysics qualified service personnel Opening this product or its accessories will void the warranty 1 1 4 Intensifier Protection In order to assure long life and high sensitivity performance do not use during daytime or bright ambient conditions Do not look at the sun or extremely bright objects Do not look at bright objects for long periods of time as this may cause the i
21. ision system is never obsolete As new cameras are introduced new adapters can be designed that deliver optimal night time imaging performance without the need to purchase an additional image intensifier In addition as new image intensifiers become available because of technology improvements these image intensifiers can be purchased to deliver even higher performance with the existing adapters and camera equipment Fully Accessorized Adapters have been designed for optimized use on Canon EOS and Nikon digital and SLR cameras as well as a wide range of Camcorders including the Canon XL1S Sony PC 110 120 and 330 C mount CCD CMOS cameras and as a viewer using an eye piece adapter Future Accessory Availability Electrophysics continues to lead the way in developing new and useful components and adapters for night time surveillance applications 1 8 2 ASTROSCOPE CONFIGURATION SET UP AND OPERATION 2 2 2 21 Removable Lens Camera and Camcorder Operation This section describes the configuration set up and operation of AstroScope Night Vision on removable lens cameras and camcorders such as Nikon SLF Digital Cameras Canon EOS type SLR Digital Cameras and Canon XL Camcorders 2 3 2 1 1 Required Components The Nikon EOS and XL adapters pairs are pictured below Handle each part carefully If any of the optics becomes dirty refer to the Maintenance section of this manual for cleaning instructions 2 1 1 1
22. ntensifier tube to develop insensitive areas 5 Accessories Use only accessories and attachments recommended by Electrophysics 6 Water and Moisture These products are NOT waterproof They are only resistant to occasional small amounts of moisture Do not operate in continuous rain conditions or in high moisture environments 7 Heat The product should be situated away from heat sources such as radiators heat registers stoves or other sources of heat 8 Power Sources This product should be operated only from the type of power source indicated here 9 Cleaning Do not use unauthorized cleaning fluids and materials See Section 5 2 for proper cleaning instructions 10 Replacement Parts Use only manufacturer approved replacement parts and accessories Damage Requiring Service Refer servicing to Electrophysics qualified service personnel under the following conditions 1 If liquid has been spilled or objects have fallen into the product 2 Ifthe unit has been exposed to rain or water and is now not operating 3 Ifthe product does not operate normally by following the operating instructions 4 Ifthe product has been dropped or damaged in any way 5 If the unit exhibits a distinct change in performance 1 2 1 3 Reference Guide Nikon Pair see pg 2 3 Wir 200mm Lens see pg 3 1 Nikon SLR and Digital Cameras Canon EOS Pair see pg 2 3 Canon EOS 3 SLR and Digit
23. o interface with the lens The standard EOS Back Body Adapter will NOT operate with this lens Sometimes an intensifier tub exhibits a faint hexagonal pattern honeycomb This is a result of the manufacturing process Note Do not be concerned if you see this feature It is an inherent characteristic found in light amplification night vision systems that incorporate a microchannel plate in the intensifier A few black spots throughout the image area are also inherent characteristics of all night vision technology These spots will remain constant and should not increase in size or number gt MAINTENANCE 5 1 Key Operational Parameters 5 1 1 Power 300mw lt 50mA typical 5 1 2 Environmental Operating Temperature 20 to 50 C Storage Temperature 40 to 80 Water Resistance Splash proof Operating Humidity 0 95 5 2 Cleaning Non optical surfaces The non optical surfaces of the lens can be cleaned with water mild detergents and a soft cloth Optical Surfaces The optical surfaces of the lens should only be cleaned when visible dirty Care should be taken to avoid touching the exposed lens faces Skin acid left behind with fingerprints can be damaging to coatings and lens substrates First use a jet of air or blow across the surface to remove any sand or abrasive particles before cleaning If oil water spots or fingerprints form on the optical surfaces clean as soon as possible using a soft cotton cl
24. ode This dim light consists of energy in both the visible and near infrared portions of the electromagnetic spectrum 2 When the light impinges on the photocathode the light sensitive portion of the image intensifier electrons are emitted with amplitude determined by the photocathode s spectral responsivity and the amount of light energy Because of the image intensifier s internal electrical field these electrons are accelerated toward the microchannel plate assembly the image intensifier s amplification mechanism 3 The microchannel plate is a glass plate with millions of tiny closely spaced channels bored through it The plate is coated with a special substance that produces secondary electron emission when impinged by an electron Due to the potential difference across the plate an incident electron enters a channel and frees other electrons from the channel wall These electrons are accelerated along the channel in turn striking the channel surface again and again giving rise to more and more electrons Eventually this cascade process yields a cloud of several thousand electrons which emerge from the rear of the plate 4 Electrons exiting the microchannel plate strike a phosphor that emits light proportional to the amount of electrons hitting it The image is green because the selected phosphor glows green when charged The green color is selected because the human eye can differentiate more shades of green than any other color
25. osition Zoom the camera until the image fills the screen Using SLR type camera focus normally using the cameras lenses Using Sony and other non removable lens camcorders require the camera to be set in the manual focus mode Set the objective lens at a known distance 5 meters and turn the camera lens ring until the image is sharp You do NOT need to adjust the camera focus ring again Focus only with the objective lens It is important to understand that all night vision devices amplify the available light If the ambient lighting conditions are very low it may be difficult to obtain a satisfactory shutter speed to hand hold the camera Make sure the lens aperture is set to its widest position ex F 1 4 In conditions where the camera wants to shoot at slower than 1 30 second you should check the ISO setting Film cameras require a film with at least and ISO of 1000 and digital camera require a minimum ISO of 800 You should increase the ISO on digital cameras when needed to shoot at 1 30 second The auto focus systems on most cameras use a variance of contrast to focus In low light conditions the contrast level is very low and the auto focus systems may not operate efficiently On Nikon camera only the Auto S lenses may auto focus non Auto S lenses will not auto focus under any condition Canon EOS lenses may auto focus and the Canon XL 16X lens will auto focus It is generally faster to manually focus these cameras
26. oth and mild neutral soap diluted with lukewarm distilled water 1 part soap to 100 parts water followed by reagent grade isopropyl alcohol or acetone swab Dust can be removed gently using alcohol or acetone swab Note Avoid swabs that incorporate plastic stems as some plastics will dissolve in alcohol or acetone 5 6 WARRANTY Electrophysics warrants that these products to be free from defects in material and workmanship Any warranty described herein shall extend to the first ultimate user only for a period of one year from the date of shipment from our factory Electrophysics obligation under this warranty shall be limited to furnishing a replacement for or at our option repairing any part which to our satisfaction proves defective provided such part is returned to the Electrophysics service facilities in New Jersey freight paid No product may be returned without prior Electrophysics approval see below Electrophysics shall not be responsible for installation costs In no event will any claim for labor in removing or replacing defective parts or for incidental or consequential damages be allowed No warranty is made on products that have not been installed operated or maintained in accordance with these instructions or which have been subjected to misuse abuse accident or alteration or to improper or negligent use maintenance storage transportation or handling Products not manufactured by Electrophysics
27. pper right back part of the camera and turn the thumb wheel located just behind the shutter button until the bar is under the 2 The ISO is now increased from 1000 to 4000 Looking through the viewfinder exposure information will be displayed on the bottom The left number is the shutter speed To the right of the shutter speed is the aperture The three dots can be disregarded 1 2 W 1 2 is the exposure guide L There is a wheel just behind the shutter release button Turn the wheel until the shutter speed displayed in the viewfinder reads 30 On the back of the camera above the large thumb wheel is another On Off switch Turn it to The large thumb wheel will now change the aperture Looking through the viewfinder adjust the wheel until the 2 8 or the lowest number appears next to the shutter speed To the far right of that display isa 1 2 W 1 2 The best exposure is when the moving line is directly under the WV To the left of the center arrow will produce a dark image and to the right will produce a bright image If there is too much light use the wheel on the top of the camera to increase the shutter speed 60 90 125 180 Shutter Speed Note Never use a shutter speed slower than 1 30 sec or the image will become blurred 2 1 3 3 ex TOL Use on Canon XL Camcorders Secure the BBA side of the 9350XL to the Camcorder Secure the Lens to the FLA side of the 9350XL Turn the Cam
28. ved substantially over the past few decades This evolution is described by different generations Gen of technology as follows Gen 1 These are the first so called night vision devices and were introduced in the early 1960s and first fielded in Vietnam These devices utilized a multi alkali S 25 photocathode having a spectral response extending from visible to about 850nm In order to have sufficient sensitivity for use in night vision applications three Gen image intensifier tubes needed to be cascaded each producing some gain The result though highly sensitive suffered from significant edge distortion as well as poor life expectancy less than 1000 hours Gen 2 By the 1970s the microchannel plate was introduced that delivered high sensitivity imaging without the need to cascade three stages As a result night vision pocketscopes and night vision goggles emerged as viable products with improved operation life 2000 4000 hours Gen 2 More recently improved Gen 2 devices have been developed known as SuperGen that deliver improved sensitivity and improved lifetime 10 000 hours Gen By the early 1990s image intensifiers became available with photocathodes made from gallium arsenide This produced significantly more sensitivity and an extended near infrared spectral responsivity range to 950nm Gen 3 Thin Film Introduced in 2002 thin film image intensifiers incorporate a new manufacturing technique
29. which are sold by Electrophysics are covered exclusively by the original manufacturer s warranty and Electrophysics may at its option assign to Buyer its warranty claims against the original manufacturer of defective products in full settlement of Buyer s possible claims against Electrophysics with regard to such products Where Buyer is a distributor financing company or similar entity acting for or on behalf of the initial user of the equipment the warranty is transferable to the initial user only In all other cases the warranty is limited to the Buyer and is not transferable unless agreed to in writing by Electrophysics The Warranty contained herein is exclusive and expressly in lieu of all other warranties written oral implied or statutory including but not limited to expressed or implied warranties of merchantability or of fitness In addition Electrophysics shall not be liable for any loss damage or injury of any nature whether direct indirect or consequential in connection with or resulting from use of the products 61 HOW TO RETURN PRODUCTS NH FOR WARRANTY REPAIR Refer to the contact information for repairs and service A Return Authorization RA number will be assigned by the service department This number must be marked clearly on the outside of the package being returned Service department will provide a shipping address 6 1 4 The following information must be included on the packing slip Reason
Download Pdf Manuals
Related Search