Newcon Optik 10MG User's Manual
Contents
1. TROUBLESHOOTING STORAGE neat nase WARRANTY ee CUSTOMER SUPPORT ACCEPTANCE CERTIFICATE 1 DESCRIPTION 1 1 The integrated day night riflescope NVS 10MG is a day night sight hereinafter referred to as the sight with the set of accessories The sight is intended for aimed firing during daylight and at night using large variety of weapons with side mounting or weaver mounting rail 1 2 The sight provides detection recognition observation of a target and aiming firing in daylight and at night 1 3 The operation temperature range of the sight is from 55 to 55 C and relative humidity up to 98 at temperature T25 G Thank you for purchasing NVS 10 MG Please read all the instructions carefully prior to use Failure to follow the instructions may void the warranty 2 DELIVERY SET NVS 10MG Weaver or side fail mount Wrench Screwdriver Battery Allen key Battery control module Soft cloth Bag Rubber eye guard Case Operational manual Disguise cover Quantity 1 1 3 SPECIFICATIONS Magnification 4x 0 2 Field of view 9 Objective lens focal length F 108mm F1 5 Objective lens diameter mm 72 Focus range m 50 Eyepiece focal length mm 27 4 Eyepiece relief distance mm 40 Dioptric adj relative to reticle Fixed 0 5 to 1 D Windage Elevation adjustment2. 13 Windage adjustment screw 15 Clutch 17 Side mount 19 Washer 21 Latch 23 Handle 6 Battery 8 Latch 10 Switch ON OFF 12 Elevation adjustment hand wheel 14 Eyepiece 16 Eyepiece Rubber 18 Mount 20 Clutching screw 22 Lever WARNING Never operate your night vision device at daylight without the lens cover on Never direct the lens to bright light The functional device scheme is given on the figure 1 see the Exhibit A In daylight the handle 5 is set into the position DAY setting the switching mechanism into position 4a Light filter 1 must be removed from the objective 2 Visible image that is formed by the objective 2 is projected onto the reticle 7 through the collective lens 3 and lens system 6 It can be viewed through the eyepiece 11 together with the aiming marks If the aiming marks on the reticle 7 are not seen well turn the switch SA1 into ON position The light diode VD1 illuminates the reticle 7 You can adjust the brightness of the aiming marks by the resistor R1 During night and in dusk turn the handle 5 into position NIGHT This sets the switching mechanism into position 4b when the image intensifier A2 replaces the lens 3 in the aiming channel Internal micro switcher SA2 is connected mechanically with the handle 5 Now when you turn the switch SA1 into ON position the power from batt
3. 10 and set the DAY NIGHT handle 9 into the position NIGHT 6 3 Mounting on weapon Side Mount Mount the sight on the weapon in the following order Adjust the mounting seat groove figure 2 with the mount type dovetail Move the sight forward up to the stop and fix it turning the handle 23 forward up to the total fixation on the mount 18 The sight should be screwed tightly to the mount Ifthe sight is not fixed tightly take the sight off the weapon and regulate the clutch on the mount For this purpose take off the latch 21 and assure that the handle 23 is placed on the number of jags that provide tight fixation of the sight then place the latch 21 back on its place 6 4 Mounting on weapon Weaver Mount Mount the sight on the weapon in the following order Using the allen key fix tightly the mount on the sight Adjust the sight with the mount on the rail Using the allen key fix tightly the mount on the weapon 7 MAINTENANCE Keep the sight clean from the dust and dirt while operating Surfaces of the optical components should be always clean Clean the glass surfaces with flannel or cotton wool saturated with ethanol or special cleaning solvent to remove grease Wind a bit of a cotton wool at the end of wooden spatula Wet cotton with the solvent Wipe the glass by wetted cotton not touching the frame Change the wool to a dry piece and finish cleaning by circular
4. 34 MoA Windage Elevation step 0 7 MoA Man viewing distance m gt 500 Vehicle viewing distance m gt 1500 Image Intensifier Tube 18 mm Gen 2 or 3 Tube sensitivity u A lm gt 500 Tube resolution lp mm gt 45 Power supply 3V 2 x AA Battery life up to 60 hours Operations temperature 55 C to 55 C Storage temperature 55 C to 70 C Waterproof construction Yes Dimensions w o mount mm 255x88x80 Weight w o batteries kg 1 600 Minute of Angle The unit works under voltage from 2 to 3 Volts To test the battery voltage use the supplied battery control module 3 4 DESIGN 14 13 1 Flight Filter 3 Collective lens 4b Switching mechanism in the position NIGHT 6 Internal lenses 8 Windage adjustment screw 10 Elevation scale 12 Direction adjustment screw 14 Photocathode of image intensifier G1 G2 Batteries SA1 Switch VD1 Light diode Figure 1 2 Objective lens 4a Switching mechanism in the position DAY 5 Handle 7 Reticle 9 Elevation adjustment wheel 11 Eyepiece 13 Image intensifier screen A2 Image intensifier R1 Resistor SA Micro switch 23 22 21 20 19 18 Figure 2 2 Objective 4 Switching mechanism 1 Light filter 3 Hand wheel for of reticle brightness 5 Battery pack 7 Battery compartment cover 9 Handle DAY NIGHT 11 Elevation scale
5. OFF switch is in the position ON is defective figure 1 Replace or recharge the battery if needed 2 Send the unit to an authorized service centre 16 9 STORAGE When preparing the unit for long term storage it is necessary to perform corrosion proofing with a special lubricant Each 4 four years the lubricant should be renewed to fully protect the device from corrosion During this operation the rest of previous lubricant coating should be removed and all metal surfaces should be degreased by a cotton wool cloth moistened in benzene The new lubricant coating should be applied after degreasing with a brush The plastic surfaces don t require anti corrosion coating When preparing for long term storage the NVS 10MGs received from the manufacturer or from the workshops it is necessary to check the completeness of equipment by comparing what is available with the list of components in the this document The reliability of NVS 10 MG attachments to weapon and parameters of adjustment by azimuth and elevation should be checked with NVS 10MG mounted on the weapon When stored the cases with NVS 10MGs should be placed on stands shelves or in cupboards at a dry heated and ventilated premise The temperature at the premise shall be between 5C and 35C relative humidity not more than 55 at temperature 25C 17 It s allowed to store the units in transportation case at temperatures up to 70C 158 F for
6. not more than 10 hours It is unacceptable to place the NVS 10MGs on the floor near stoves and windows that let through direct sunrays Presence of acid and alkaline vapour as well as of other aggressive admixtures in the air is unacceptable After a 4 year period of storage it is necessary to perform thorough check up of the NVS 10MGs functionality 10 WARRANTY NEWCON warrants this product against defects in material and workmanship for one year from the date ofthe original purchase Longer warranty is available subject to the terms ofthe specific sales contract Should your Newcon product prove to be defective during this period please deliver the product securely packaged in its original container or an equivalent along with the proof of the original purchase date to your Newcon Dealer Newcon will repair or at its option replace with the same or comparable model the product or part thereof which on inspection by Newcon is found to be defective in materials or workmanship What This Warranty Does Not Cover NEWCON is not responsible for warranty service should the product fail as a result of improper maintenance misuse abuse improper installation neglect damage caused by disasters such as fire flooding lightning improper power supply or service other than by aNEWCON Authorized Service Postage insurance and shipping costs incurred while presenting your NEWCON product for warranty service are your respon
7. NO NEWCON OPTIK Operation Manual East European Mount Picatinny Mount NVS 10MG DAY NIGHT VISION SCOPE 105 Sparks Ave Toronto ON M2H 2S5 Canada IMPORTANT INFORMATION READ PRIOR TO ACTIVATION You have just purchased a complicated electronic device To operate it properly please read this manual carefully Here are some common Precautions that must be noted e NEVER expose the opened objective lens of an active unit in daylight if operating in night mode At daytime objective lens must be covered by caps There is a tiny hole in the cap to provide enough light for day time operation e NEVER aim active unit at intense light sources i e lights headlamps campfires the Moon etc e NEVER reverse the polarity of a battery e NEVER disassemble the unit e NEVER connect the unit to external power sources e ALWAYS remove batteries when not in use for a long period e ALWAYS keep the objective lenses covered when not in use e ALWAYS store in a warm dry place when not in use CN 2 E TABLE OF CONTENTS DESCRIPTION e ee DELIVERY SET SPECIFICATIONS S eeudna iania DESIGN ea aaa a lol esoo deal TOOLS AND ACCESSORIES GENERAL INFORMATION Precautions iia de General Instructions u een Mounting on weapon Side Mount Mounting on weapon Weaver Mount MAINTENANCE
8. eries Gl and G2 is applied to the image intensifier A2 Visible image from the image intensifier screen 13 is projected onto the reticle 7 and is viewed through the eyepiece 11 together with the aiming marks In twilight the light filter 1 should be on the objective 2 for image intensifier protection from light overloads The sight consists of following components objective 2 figure 2 with mounted light filter 1 switching mechanism 4 eyepiece 14 and interchangeable mount 17 with fixing mechanism The rubber eye shade 16 eases the eye orientation relatively to sight eye relief and protects the eye from recoil It is fixed on the eyepiece 14 with the clutch 15 Two rechargeable or non rechargeable batteries of AA type are organized in a battery pack 5 which is placed into the battery compartment 6 and closed by cover 7 To fix the cover 7 turn the latch 8 counter clockwise The sight has following controls see figure 2 e the ON OFF switch 10 for turning on the reticle illumination and image intensifier SA1 on figure 1 e the DAY NIGHT handle 9 for setting the switching mechanism 4 into the day or night operating mode e the hand wheel 3 for smooth brightness adjustment of the reticle e the hand wheel 12 for elevation adjustment e the screw 13 for windage adjustment 5 TOOLS AND ACCESSORIES Battery control module should be used for the field inspection of the batte
9. motions from center to edge While cleaning be careful to not afford the solvent to penetrate under the frame This will lead to the dissolution of the jointing putty and breaking of the sight sealing To remove dirt from the battery pack contact plates battery pack and from the contacts of the control module YK battery use the similar procedure It is necessary to keep maintenance of the sight to provide constant readiness and reliability increase durability and remove the signs of untimely wear and tear and damage of the component units and parts 15 8 TROUBLESHOOTING Problem Probable reasons Possible solutions There is no Power supply is Check the battery luminescence of discharged charge with battery image intensifier screen control module Replace or recharge the battery if needed Area image is blurred and faint The optics is dirty or covered with moisture Wipe the eyepiece and objective surfaces with napkin Black spots of faults and damages impeding the confident sight work appeared Image intensifier is damaged by aiming at light source or turning the unit on ina daytime Send the unit to an authorized service centre in the field of view There is no 1 The power supply is 1 Check the battery aiming marks discharged charge with battery fluorescence 2 Emissive diode VD1 control module when hand wheel is set on the maximum brightness and the ON
10. oid the recoil impact ALWAYS work with light filter in twilight ALWAYS turn off the sight when not in use in night time ALWAYS switch the handle day night into the day position when the sight is not in use 6 2 General Instructions Prior to usage be sure that you understand the sight controls and fixing mechanism If the sight was in storage clean optical components with napkin Remove the lubricant from the metallic surfaces In conditions that require high level of camouflage at night time set the protected eyeshade on the sight in the following order unclasp the clutch 15 figure 2 take off the eyeshade 16 together with the clutch 15 put the eyeshade 16 into the case take the protected eyeshade from the kit put the clutch 15 on the eyeshade fit the eyeshade to the eyepiece frame stretching it a little fasten the clutch If the outside temperature is below zero keep the battery pack in the inner pocket of your clothes Check the voltage of the single battery in the following order place the power supply into the battery control module keeping the polarity right up ifany LED is on the battery is charged if it is not then the battery is discharged and must be replaced Install the battery pack on the sight in the following order 11 place the ON OFF switch into the position OFF Visibility decreases and or disappears Bright light sources moon projectors
11. or headlights may result in visibility degradation or even complete disappearance If this happens move the scope away from the light source immediately The image should be restored in within 2 minutes Poor atmospheric conditions such as fog haze or extremely dark environments will decrease the visibility distance as well Place the handle DAY NIGHT 9 into the position DAY Open the cover 7 by turning the latch 8 clockwise Take out the battery pack 5 Place two charged batteries or two AA cells into the battery pack 5 observing the marked polarity Locate the groove on the top side of the pack and place it into the compartment The battery pack must slide effortlessly into the compartment Close the cover 7 by turning the latch 8 counter clockwise Put the light filter 1 on the objective 2 Set the DAY NIGHT handle 9 into the position NIGHT turn on the ON OFF switch 10 and put the hand wheel 3 into the middle position You should see the aiming marks on the yellow green background Turn offthe switch 10 In a daytime set the DAY NIGHT handle 9 into the position DAY check that the switch 10 is in the OFF position and then take the light filter 1 off the objective 2 In twilight put the light filter 1 on the objective 2 turn on the switch 10 and set the DAY NIGHT handle 9 into the position NIGHT In the night take the light filter 1 off the objective 2 turn on the switch
12. ries It has four LEDs on the front panel Numbers 1 1 1 2 1 3 1 4 which are marked near the LEDs indicate battery voltage in Volts The accuracy of voltage measurement is 0 1 V The wrench key is designated for turning the windage screw 13 The protected rubber eye shade from the accessories kit is used instead of the standard eye shade 16 It is designed for night work under conditions that require high level of camouflage It hides the green light spot on the shooter s face when the shooter is not aiming The soft cloth is intended for cleaning of the external surfaces of optical components contacts and battery control module The bag is intended for packing up the sight and its protection while carrying and transporting The cover is used when the sight is transported being mounted on a weapon The accessories are stored inside the cover 6 GENERAL INFORMATION 6 1 Precautions NEVER switch the handle day night into the night position in a daytime without the light filter on the objective NEVER aim the sight to the bright sources of light flares glowing automotive head lamp when it is on NEVER touch the optical components by hands Dust grease and dirt from the optical surfaces must be removed with the napkin NEVER short the circuit between the batteries and metallic parts of the body NEVER use sight not fixed firmly on the weapon NEVER press the eye shade too intensively to av
13. sibility 11 CUSTOMER SUPPORT Should you experience any difficulties with your NEWCON OPTIK product consult the enclosed manual If the problem remains unresolved contact our customer support department at 416 663 6963 or toll free at 1 877 368 6666 Our operating hours are 9am 5pm Monday Friday Eastern Standard Time At no time should equipment be sent back to Newcon without following the instructions of our technical support department NEWCON OPTIK accepts no responsibility for unauthorized returns To locate NEWCON Authorized Dealer call Tel 416 663 6963 Fax 416 663 9065 Email newconsales newcon optik com Web www newcon optik com The defective products should be shipped to US customers 2498 Superior Ave Cleveland OH 44114 From all other countries 105 Sparks Ave Toronto ON M2H 2S5 CANADA 20 12 ACCEPTANCE CERTIFICATE NIGHT VISION DEVICE NVS 10MG NVS 10MG serial number Image Intensifier Tube serial number Complies with all technical specifications and has passed the inspection Date of production Quality Inspector Quality Assurance Seal 21 TUS TY NEWCON OPTIK Printed in Canada
Download Pdf Manuals
Related Search