Netgear GS108T User's Manual
Contents
1. N E T G E A R Installation Guide GS108T 8 Port Smart Switch Start Here Follow these instructions to set up your smart switch Prepare to Install Your Smart Switch e Prepare a PC with an Ethernet adapter and a CD ROM drive e Before proceeding with the smart switch installation familiarize yourself with the contents of the Resource CD especially the manuals that accompany this Switch First Install the Smartwizard Discovery Utility on a PC 1 Power on your PC let the operating system boot up and log in as needed 2 Insert the Resource CD for the Smart Switch Series into your CD drive The 3 Run the Setup program to install the Smartwizard Discovery utility Follow the prompts to complete the installation 4 Click OK when done Next Connect Your Smart Switch in the Correct Order These instructions assume you are using DHCP in your network If you are using static IP addressing in your network configure the switch IP address before connecting it to your network In the absence of a DHCP server the switch will default to 192 168 0 239 for its IP address To configure the switch before connecting it to your network 1 Set up the PC with an IP address in the 192 168 0 x subnet and connect the PC to the switch 2 Then use the Smartwizard Discovery utility to configure the switch Smart Switch NETGEAR Peete AEI HEAT saat Sworn GS IDET PC with SmartWizard Discovery Utility To connect the switch to you2. Be sure to power on your PC and smart switch in the correct sequence Follow this sequence Turn off the smart switch and computer First turn on the smart switch and wait two minutes Next turn on the computer Make sure the Ethernet cables are securely plugged in For each powered on computer connected to the smart switch with a securely plugged in Ethernet cable the corresponding smart switch LAN port status light will be lit Make sure the network settings of the computer are correct In most cases computers should be configured to obtain an IP address automatically via DHCP If your network uses static IP addresses be sure the switch and computer are configured with valid IP addresses Technical Support Thank you for selecting NETGEAR products After completing setup and configuration locate the serial number on the bottom label of the Smart Switch and use it to register your product at http www netgear com register Registration on the web site or over the phone is required before you can use our telephone support service The phone numbers for worldwide regional customer Support centers are on the Warranty and Support Information card that came with your product Go to http www netgear com support for product updates and web support This symbol was placed in accordance with the European Union Directive 2002 96 on the Waste Electrical and Electronic Equipment the X WEEE Directive If disposed of within the Eur
3. e switch and displays its MAC Address IP Address and model number If you cannot configure your switch verify that the IP address configuration of the PC is in the same subnet as the switch If they are not on the same subnet click Configuration Setting and enable DHCP 3 Click to select the line displaying the details of your switch If there are multiple smart switches in your network be sure to select the one you want to configure 4 Click Web Access to view the switch Login screen Login Password LIL iii 201 11199 01 November 2007 5 Enter the default password of password in lower case letters and click Login The System gt Management screen will display Consult the Resource CD or the on line link to the Reference Manual by selecting Help gt User Guide for assistance with configuration procedures Qo5 Security Monitoring Maintenance System Switching Management LLDP i SNMP System Information IP Configuartion Switch Status Time Product Name asiasT Firmware Version 3 0 0_01 System Name System Locaton Idle Timeout 5 3 to 30 minutes DHCP Enabled IP address 10 1 31 47 Subnet mask 255 255 255 0 Default gateway 10 1 31 13 MAC address OO Lb 2f 28 8f 80 System UpTime O days O hours 3 mins 36 seconds Select from the configuration menu options to configure the switch for your network Troubleshooting Tips Following are some tips to correct simple problems that might occur
4. opean Union this product should be treated and recycled in accordance with the laws of your jurisdiction implementing the WEEE Directive 2007 by NETGEAR Inc All rights reserved NETGEAR and the NETGEAR logo are registered trademarks of NETGEAR Inc in the United States and or other countries Other brand and product names are trademarks or registered trademarks of their respective holders Information is subject to change without notice
5. r network 1 Connect each device to an network port on the switch front panel 2 Connect the smart switch to your network 3 Connect the external power supply and power on the switch 4 Verify that the PC with the Smartwizard Discovery utility is on the same subnet as the switch Smart Switch NETGEAR mir EMET GGA wet path GSIDET Gigabit uv r Drejt Ba ee Ethernet _ neat Lipper A e Factory i 2 J 4 i 5 T a Peme Beeb Date INTERNET A Servers Computers S Printers Now Configure the Switch with the Smartwizard Discovery Utility 1 Double click the Smartwizard Discovery icon _ on your desktop or in Windows Start menu Programs to run the utility and view this screen File Help Device List MAC Address IP Address Protocol Version Product Name System Name Location lt gt of a a a DHCP Refresh f Discover Device Setting Configuration Setting Password Change Web Access Firmware Upgrade Exit Necccccccccccccccscsccscsessescsssccscscesessesed 2 Click Discover to find your switch in the network File Help Device List MAC Address IP Address Protocol Version Product Name System Name Location O040f4621bf6 10 1 1 104 2 001 002 FS 50T DHCP Refresh i Device Setting L a a u Configuration Setting Password Change Web Access j Firmware Upgrade Exit The Smartwizard Discovery utility finds th
Download Pdf Manuals
Related Search