NEC XEN IPK User's Manual
Contents
1. IAD MEGACO TRUNK EXTENSION QUICK SETUP GUIDE NEC Business Solutions Ltd Document No 8684 Release 1 0 June 2004 June 2004 Business Solutions Ltd THIS PAGE INTENTIONALLY LEFT BLANK IAD MEGACO TRUNK EXTENSION QUICK SETUP GUIDE Doc No 8684 Release 1 0 June 2004 Doc No 8684 Release 1 0 June 2004 Disclaimer NEC shall not be liable for any direct indirect consequential or incidental damages about the use of this equipment manual or any related materials The information in this technical manual is advisory in nature and is subject to change NEC may make improvements and changes in the products described in this manual without notice Changes will be periodically made to the information in the new editions Efforts have been made to ensure that the contents of this manual are correct Should you find any error NEC welcomes your comments to improve our communications please contact NEC on 1800 036 136 Contents of this manual are subject to change without prior notice at the discretion of NEC Business Solutions Ltd This document has been prepared for the use of employees and customers of NEC Business Solutions Ltd and may not be reproduced without the prior written approval of NEC Business Solutions Ltd Copyright 2004 NEC Business Solutions Ltd 633 647 Springvale Road Mulgrave Vic 3170 IAD Megaco Extension Quick Setup Guide iii June 2004 Business Solut2. 1 Configure DIPSW 52 in accordance to Table 2 Place the IAD 8 U ETU in the Xen IPK KSU Connect the Ethernet cable to connector J6 The CH1 CH8 LEDs start to run indicating that the system is initial ising the IP Networking parameters The Status LED 012 is red refer to Table 1 Boot Up Sequence LED Patterns 4 Once all the LEDs are OFF and the Status LED D12 is flashing red the IAD 8 U can be set up with the system 34 Hardware Setup Doc No 8684 Release 1 0 June 2004 Doc 8684 Release 1 0 June 2004 Xen Programming SECTION 2 XEN IPK PROGRAMMING After the Dip Switches have been set and the IAD ETU has been installed in the Xen IPK KSU you are ready to program the settings the for the IAD ETU The IAD 8 U ETU MEGACO Station is recognised by the Xen IPK system as 51 8 0 ETU This ETU takes a longer time to initialize than the other Xen IPK ETUs and must be programmed using Memory Block 7 1 Card Interface Slot Assignment 2 1 Programming the ETU Interface Slot The following procedure provides the general directions for Xen IPK programming for the ETU Interface Slot Assignment From port 01 or 02 enter programming mode Press ODO Assign the Card Interface Slot Assignment by pressing LK7 and LK1 Press or for the cabinet number of KSU where the IAD 8 U is installed Press to move the cursor to the r
3. ernet Explorer 5 0 and higher 3 When the login screen appears enter the Login ID and password Click login Default login ID admin Default password password 4 Set the IP Address Subnet Mask Host Name and Default IP parameters the IAD 8 U Card tab and select Submit 5 Set the IP Station Encoding Preference Packet Size Jitter Depth and the IP Address or use DHCP if using a DHCP Server under the Port Tab and select Submit 6 Select the System tab then select Reset the Card The ETU goes through a reboot cycle This may take a few minutes 7 Disconnect the crossover cable and connect the IAD 8 U ETU MEGACO Station to your network The ETU is now ready for operation IAD 8 U ETU Web Programming Doc No 8684 Release 1 0 June 2004
4. ight Enter slot number 1 8 of the KSU containing the IAD 8 U ETU Press to change the page number Page 2 and assign the ESI ETU Press LK1 Press to write the data Additional programming is required to assign telephone type and station number 10 Assign the telephone type assignment by pressing LK7 and LK2 If assigning MEGACO terminals assign ports as TEL LK2 11 Assign station number assignment on a per port basis MB 4 10 IPK IAD Megaco Extension Quick Setup Guide 35 June 2004 Business Solutions Ltd SECTION 3 IAD 8 U WEB PROGRAMMING 36 When installed for the first time the IAD 8 U comes up with factory set default parameters as shown in Table D 2 Factory Network Settings Table 0 2 Factory Network Settings Host Name neciad IP Address 192 168 1 100 Subnet Mask 255 255 255 0 Default Gateway 192 168 1 1 In this configuration the ETU cannot run in any randomly given environment and its parameters must be redefined before the IAD 8 U ETU can work in your environment 1 Boot up a PC with IP Address 192 168 1 X Subnet Mask 255 255 255 0 Connect to the IAD 8 U either via a crossover cable or a small hub 2 Connect the IAD 8 U via your Web Browser to the following link http 192 168 1 100 IAD 8 U supports Microsoft Int
5. ions Ltd THIS PAGE INTENTIONALLY LEFT BLANK Disclaimer Doc No 8684 Release 1 0 June 2004 Doc No 8684 Release 1 0 June 2004 Setting Up the Megaco Station Application SECTION 1 HARDWARE SETUP IPK IAD Megaco Extension Quick Setup Guide Ethernet Port 2 Ethernet Port 1 2 12345678 ON T 1 10 2 1 N 115 2 Figure 0 1 I AD 8 U ETU J6 012 LIVE LED D1 CH8 LED D3 LEDL D5 CH6 LED D7 CH5 LEDU D2 D4 CH3 D6 CH2 LEDL D8 CH1 mee jy 510 Reset COM Port 33 June 2004 Business Solutions Ltd 1 1 Boot Up Sequence LED chart shows the status of the IAD 8 U card during boot up The LED conditions change as the IAD 8 U passes through different boot states Table 1 Boot Up Sequence LED Patterns STATE D8 D6 D4 D2 D7 D5 D3 D1 012 CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 LIVE 1 Q Q Q Q Q Q Q Q 2 Q Q x 3 Q Q Q Q Q Q Q Q x 4 Q Q Q x 5 Q Q Q Q Q Q 6 Q Q Q Q Q Q Q Q x LED LED OFF amp LED Flashing 1 2 Connectors J6 Default Ethernet connection 1 3 52 DIP Switch Settings Table 0 1 52 DIPSW Settings Auto No of Reserved Sense Ports Mode Operation swt SW2 SW3 sw4 SW5 5 6 SW7 SW8 OFF OFF OFF ON ON ON OFF OFF 51 8 010 ETU
Download Pdf Manuals
Related Search