NEC SigmaBlade B120a-D Setup Guide
Contents
1.2. NEC BladeServer CPU 1CPU 2CPU 1CPU 2CPU amp CPU
3. Observe the following instructions to use the server safely Failure to follow these instructions may result in death or serious personal injury Electric Fire hazard hazard Do not disassemble repair or alter the Explosion Fire server R hazard prohibition Em Do not remove the lithium nickel cadmium or nickel hydrogen battery Z m Do not handle the CPU blade with the power cord being plugged to a power Unplu Water ping source prohibition 9 Do not disassemble Notes on installing the memory ANTI STATIC MEASURES The CPU blade contains electronic components sensitive to static electricity Avoid failures caused by static electricity when installing or removing any optional devices m Wear a wrist strap an arm belt or anti static glove Wear a wrist strap on your wrist If no wrist strap is available touch an unpainted metal part of the cabinet before touching a component to discharge static electricity from your body Touch a metal part regularly when working with components to discharge static electricity m Select a suitable work space Work with the CPU blade on the anti static or concrete floor When you work with the CPU blade on a carpet where static electricity is likely to be generated make sure take anti static measures beforehan
4. N N8402 042 043 044 045 Registered DIMM 1 N8402 046 Unbuffered DIMM 2 Registered DIMM Unbuffered DIMM CPU CPU 2 CPU2_DIMM1 CPU2_DIMM6 1 N8402 042 1GB DDR3 1066 1GB DIMM Registered x 1 F 1 2 DDR3 1066 2GB DIMM Registered x 1 DDR3 1066 4GB DIMM Registered x 1 DDR3 1066 8GB DIMM Registered x 1 DDR3 1333 2GB DIMM Unbuffered x 2 1 1 2 1 CPU CPU OFF 2 CPU 3 CPU 4
5. 2 Fig 2a NNNS aN CPU 6 Fig 2b 7 CPU 8 Sf Fig 2c 9 Fig 2d 10 DIMM
6. 8 10 11 12 CPU CPU ON 13 CPU ON CPU POST 14 BIOS SETUP Advanced Memory Configuration Normal 15 Advanced Reset Configuration Data Yes 16 x 1 5 Windows 1 7 Etz Unbuffered DIMM
7. NEC B120a d Memory Module for B120a d Setup Card 856 128215 002 00 05 2009 Rev 01 x 856 128215 002 00 A ie Csi amp REE e EE lt et
8. d m Use a work table Place the CPU blade on an anti static mat to work with it m Cloth Do not wear a wool or synthetic cloth to work with the CPU blade Wear anti static shoes to work with the CPU blade Take off any jewels a ring bracelet or wrist watch before working with the CPU blade m Handling of components Keep any component in an anti static bag until you actually install it to the CPU blade Hold a component by its edge to avoid touching any terminals or parts To store or carry any component place it in an anti static bag Additional notice In addition to the above notes observe the following precautions while doing the installation Do not put the memory modules in a dusty place Do not put the memory modules in a place where water or liquid is likely to splash onto the board Do not put the memory modules in a place where steam of sulfur occurs in the air Do not put the memory modules in magnetic field mDo not touch any terminal pin of memory modules Transfer of the Unit to a Third Party When transferring or selling the unit to a third party give this operation manual to that party These contents of this document will be changed without notice Preface This memory module is an expansion kit for your system The memory module substaintilly increases your system speed and responsiveness Users benefit through increased productivity complete more work in a
9. day or spend the time saved to improve work quality Read this guide carefully for proper installation Adding Order and Precautions m Adding order depends on the number of CPUs installed 1 CPU configuration Install the memory starting from the smallest DIMM slot number 2 CPU configuration Alternately install the memory starting from the smallest DIMM slot number of each CPU m Install the memory starting from the largest capacity and from the smallest slot number m Adding unit depends on N code assigned to DIMM N8402 042 043 044 045 Registered DIMM Can be installed one by one N8402 046 Unbeffered DIMM Must be installed two in pair m The CPU blade does not operate correctly if Registered DIMM and Unbuffered DIMM are mixedly installed m f the CPU blade does not have CPU 2 installed DIMM slots CPU2_DIMM1 to CPU2_DIMM6 are unavailable Step1 Unpacking After you unpack the package check if it contains the following Memory Module N8402 042 1GB 042 1GB DDR3 1066 1GB DIMM Registered x 1 Memory Capacity DDR3 1066 2GB DIMM Registered x 1 DDR3 1066 4GB DIMM Registered x 1 DDR3 1066 8GB DIMM Registered x 1 DDR3 1333 2GB DIMM Unbuffered x 2 Memory Module Setup Card This manual Step2 Installing the memory After the shutdown processing for the CPU blade to be removed turn off the power of the CPU blade Take the CPU blade out from the Blade Encl
10. osure Refer to the User s Guide of the Blade Enclosure Put the CPU blade on an anti static sheet with little dust Remove the two screws fixing the top cover Firmly hold the cover move it slightly toward the rear of the blade then lift the cover to remove it from the CPU blade IMPORTANT Handle the cover carefully so as not to make it contact with any electronic devices on the CPU blade Remove the screws from the air duct cover see Fig 2b Firmly hold the cover and lift it to remove IMPORTANT Pay attention not to make the cover hit any electronic component on the CPU blade Open the levers at both ends of the DIMM socket see Fig 2c Push the memory into the socket straight If the memory is inserted into the DIMM socket the lever is automatically closed IMPORTANT Use extreme care when installing a memory Applying too much pressure can damage the socket Keyed memory insert only one way 10 11 12 13 14 15 NOTE Make sure of the orientation of the memory The connecting side of the memory has a cut out to prevent an incorrect insertion Fig 2d Close the lever firmly If you need to install two or more memorys install them according to steps 8 through 10 Install the components having been removed Make sure that no error message appears on the POST screen Run SETUP and select Advanced Memory Configuration to verify that the installed memory shows the sta
11. tus Normal Set Advanced Reset Configuration Data in the Advanced menu to Yes This is required to update the hardware configuration information Set the paging file size to a value larger than the recommended value installed memory 1 5 for Windows Removal To remove the memory provide the preparation of the removal following steps 1 to 7 in the installation procedure and open the levers at both ends of the DIMM socket to be removed The lock is released to allow you to remove the memory If you are removing Unbuffered memory remove the pairing memory from another memory connector
Download Pdf Manuals
Related Search