NEC NP-M282X Installation and Setup Guide
Contents
1. edge stud finder is highly recommended Always use an assistant or mechanical lifting equipment to safely lift and position equipment Tighten screws firmly but do not overtighten Overtightening can damage the items greatly reducing their holding power This product is intended for indoor use only Use of this product outdoors could lead to product failure and personal injury This product was designed and intended to be mounted to the following supporting surfaces checked below with the hardware included in this product as specified in the installation sheet To mount this product to an alternative supporting surface contact Peerless customer care at 1 800 865 2112 This product was designed to be installed on the following ceiling construction only CEILING CONSTRUCTION ADDITIONAL HARDWARE REQUIRED Wood Stud None Wood Joist None Solid Concrete None Cinder Block Contact Customer Service Brick Contact Customer Service Other or unsure Contact Customer Service Tools Needed for Assembly e stud finder edge to edge stud finder is recommended e phillips screwdriver e drill e 5 16 bit for concrete surface e 5 32 bit for wood studs e level Table of Conten E E E S E E Ad ca da dda ceeded vdieccdd a E A couenes iaaaadeefasdevunagivastaetiesty 3 Installation to Extension Columns Ceiling Plate 0 cece einer ent renee er E AEE E EE 4 Installation to Wood Joist CeilINGS 0 eter i rr rr nn ene eee eerie e2. surface must be counterbored as shown below Be sure concrete anchors do not pull away from concrete when tightening screws If plaster drywall is thicker than 5 8 custom fasteners must be supplied by installer not evaluated by UL NCORRECT CORRECT Wu d concrete e H 6 concrete gt T W e O lt Q do 3 concrete surface G 3 Tighten all fasteners CONCRETE CEILING ARROW ON TOP OF PROJECTOR MOUNT ASSEMBLY INDICATES FRONT OF MOUNT 6 of 10 Visit the Peerless Web Site at www peerlessmounts com ISSUED 10 01 10 SHEET 056 9034 4 07 29 11 For customer care call 1 800 865 2112 Installation to Threaded Rod Not evaluated by UL Professional installation only Thread two 1 4 20 hex thin nylon insert locknuts not included on two 1 4 20 threaded rods not included to the desired height of projector mount assembly Attach projector mount assembly A to the two 1 4 20 threaded rods using two 1 4 20 hex thin nylon insert locknuts as shown in figure 4 1 or figure 4 2 1 4 20 THREADED ROD NOT INCLUDED 1 4 20 HEX THIN NYLON INSERT LOCKNUT NOT INCLUDED ARROW INDICATES FRONT OF MOUNT 1 4 20 HEX THIN NYLON INSERT LOCKNUT NOT INCLUDED 1 4 20 THREADED ROD NOT INC
3. 2 Installation to Extension Column Ceiling Plate NOTE Refer to accompanying instructions with ceiling plates sold separately for installing these models to ceiling Screw projector mount assembly A onto extension column as shown in figure 1 1 Tighten swivel stop screw against extension column flush mount tube or reducer using 4 mm security allen wrench B as shown in figure 1 2 NOTE Swivel stop screw is used to jam against threads of extension column flush mount tube or reducer to prevent any excess movement of projector mount assembly A Do not overtighten screw overtightening screw will damage threads making it difficult to separate products Skip to step 5 a T 1 1 2 EXTENSION COLUMN SOLD SEPARATELY UL LISTED EXT OR AEC SERIES ARROW INDICATES FRONT OF MOUNT CMJ 455 SOLD SEPARATELY SWIVEL STOP SCREW fig 1 2 4 of 10 ISSUED 10 01 10 SHEET 056 9034 4 07 29 11 Visit the Peerless Web Site at www peerlessmounts com For customer care call 1 800 865 2112 Installation To Wood Joist Ceilings A WARNING e Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components Tighten wood screws so that projector mount assembly is firmly attached but do not overtighten Overtightening can damage the screws greatly reducin
4. LUDED 1 4 20 HEX THIN NYLON INSERT LOCKNUT NOT INCLUDED ARROW INDICATES FRONT OF MOUNT 1 4 20 HEX THIN NYLON INSERT LOCKNUT NOT INCLUDED fig 4 2 7 of 10 ISSUED 10 01 10 SHEET 056 9034 4 07 29 11 Visit the Peerless Web Site at www peerlessmounts com For customer care call 1 800 865 2112 Attaching Adapter Plate to Projector Align shoulder on connection block EE opposite EE O notch in adapter plate AA Attach adapter plate AA to connection block EE using two 10 32 x 3 8 serrated washer head socket pin screws C NOTCH INDICATES g as shown in figure 5 1 Tighten screws using 4 mm FRONT OF PROJECTOR eee allen wrench B Flip projector upside down and attach adapter plate AA using four serrated socket pin screws BB and retaining spacers CC as shown below Tighten using 4 mm allen wrench B NOTE Retaining spacers CC go between the projector and adapter plate AA 8of10 ISSUED 10 01 10 SHEET 056 9034 4 07 29 11 Visit the Peerless Web Site at www peerlessmounts com For customer care call 1 800 865 2112 Attaching Adapter Plate to Projector Mount A WARNING e Do not lift more weight than you can handle Use additional man power or mechanical lifting equipment to safely handle placement of the screen Slide connection block EE with projector into projector mount assembly A as shown Tighten captive screw to secure projector to projector mount as
5. NEC NEC Display Solutions of America Inc Installation and Assembly Manual Custom Ceiling Mount for NEC M260X M260W M271X M300X M300W M300XS M300WS M311X M311W P350X P350W P420X Projectors Model MP300CM Features e ImageLock alignment prevents picture sag or drift Wrench access slot for easier flush mount installations C s L US LISTED e Exclusive aluminum track quick release Max UL Load Capacity 50 Ib 22 7 kg 1 of 10 ISSUED 10 01 10 SHEET 056 9034 4 07 29 11 Visit the Peerless Web Site at www peerlessmounts com For customer care call 1 800 865 2112 NOTE Read entire instruction sheet before you start installation and assembly A WARNING Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet If you have any questions regarding any of the instructions or warnings please call Peerless customer care at 1 800 865 2112 This product should only be installed by someone of good mechanical aptitude has experience with basic building construction and fully understands these instructions Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components Never exceed the Maximum UL Load Capacity See page 1 If mounting to wood joist ceilings make sure that mounting screws are anchored into the center of the joist Use of an edge to
6. as shown below Pull knob out and turn by hand for easy adjustment or insert 2 phillips screwdriver in end of knob and turn KNOB FOR PITCH ADJUSTMENT ARROW INDICATE FRONT OF MOUNT BACK OF MOUNT SCREW FOR YAW SWIVEL STOP REFER TO STEP 1 INSTALLATION TO EXTENSION COLUMNS FIG 1 2 KNOB FOR ROLL ADJUSTMENT To prevent tampering with the pitch and roll adjustments Tighten the two tamper resistant security screws on the projector mount assembly using 4 mm security allen wrench B to lock the pitch and roll adjustments as shown below Note Tighten screws firmly but do not overtighten Overtightening can damage the mount CAUTION e Do not adjust pitch or roll while tamper resistant security screws are fully engaged e Loosen the two tamper resistant security screws one complete turn before adjusting the projector mount assembly or damage may occur TO LOCK PITCH TIGHTEN TAMPER RESISTANT SECURITY SCREW SIDE VIEW 10 of 10 ISSUED 10 01 10 SHEET 056 9034 4 07 29 11 Visit the Peerless Web Site at www peerlessmounts com For customer care call 1 800 865 2112 2011 Peerless Industries Inc All rights reserved All other brand and product names are trademarks or registered trademarks of their respective owners
7. g their holding power Never tighten in excess of 80 in Ib 9 N M Make sure that mounting screws are anchored into the center of the stud The use of an edge to edge stud finder is highly recommended Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs Installers are responsible to provide hardware for other types of mounting situations not evaluated by UL Place projector mount assembly A on ceiling as a template and mark the center of the two mounting holes 2 Make sure that the mounting holes are in the center of the wood joist Drill two 5 32 4 mm dia holes to a minimum depth of 2 5 64 mm Attach projector mount assembly A with two 14 x 2 5 wood screws F and two flat washers E as shown in figure 2 1 or figure 2 2 depending on joist orientation NOTE Mounting slots on projector mount assembly allow for 30 15 of swivel adjustment before fully securing wood screws Tighten wood screws F using 3 8 10mm socket wrench phillips screwdriver or 10mm open end wrench until projector mount assembly A is firmly attached Skip to step 5 ACCESS SLOT FOR OPEN END WRENCH WOOD JOIST ALLOWS TIGHTENING WOOD JOIST OF WOOD SCREW FRONT OF t7 NYI CEG ARROW ON TOP OF PROJECTOR MOUNT ASSEMBLY INDICATES FRONT OF MOUNT fig 2 1 fig 2 2 5 of 10 ISSUED 10 01 10 SHEET 056 9034 4 07 29 11 Visit the Peerless Web Site a
8. rie ee ENNN NE eee neeeeerenneeeeereea 5 Installation to Concrete COINMGS sssiiiceceiastieze cons unctila chs E E ntuedseeavuail a deertas ts a 6 Installation to Threaded ROdS iiss ccccevesscccevvvesccctetvessccviievescnecieuvescccuedvesscctevvdesocedavessnncduvevesensueevesseacdedesestesieveesccaiievessaccdeeveace 7 Attaching Adapter Plate to Projectors iis is cicesanigcedccevedescecsueaynceecbthetecaays sunt A ce ravilaceuaniaceacternaiedeauenreene 8 Attaching Adapter Plate to Projector MOUNT cece tt rrr int nn ne teenie eee ene neee eee naaeeeeeeeneeeeseenaeeeeeeeaas 9 Projector Aignis nana G S S O E A nanan rviacvtlenaas 10 2 of 10 ISSUED 10 01 10 SHEET 056 9034 4 07 29 11 Visit the Peerless Web Site at www peerlessmounts com For customer care call 1 800 865 2112 Before you start check the parts list to insure all of the parts shown are included Parts List Description projector mount assembly 054 2171 4 mm security allen wrench 560 9646 10 32 x 3 8 serrated washer head socket pin screw 520 2151 10 32 x 1 4 socket pin screw 520 2196 flat washer 540 1078 14 x 2 5 phillips hex head wood screw 5 1 015 C04 concrete anchor 590 0320 adapter plate 055 2985 M4 x 16 mm serrated socket pin screw 510 2087 retaining spacer 590 2009 2 mm allen wrench 560 1097 connection block 580 4065 3 of 10 ISSUED 10 01 10 SHEET 056 9034 4 07 29 11 Visit the Peerless Web Site at www peerlessmounts com For customer care call 1 800 865 211
9. sembly A FRONT OF MOUNT ARROW INDICATES FRONT OF MOUNT EE CAPTIVE SCREW assembly A and into connection block EE as shown in detail 1 Tighten screw using 4mm security allen wrench B O IMPORTANT For security installations insert one 10 32 x 1 4 socket pin screw D through projector mount DETAIL 1 9 of 10 ISSUED 10 01 10 SHEET 056 9034 4 07 29 11 Visit the Peerless Web Site at www peerlessmounts com For customer care call 1 800 865 2112 Projector Alignment To adjust yaw swivel for wood stud concrete ceiling and threaded rod mounting applications Loosen wood screws F if flush mounted to wood joists page 5 or concrete ceilings page 6 or loosen locknuts on threaded rods page 7 until projector mount can be rotated Rotate mount to desired position and retighten screws or locknuts To adjust yaw swivel for extension column applications Loosen screw on projector mount assembly A indicated below until projector mount can be rotated Rotate mount to desired position and retighten screw To adjust pitch forward and backward tilt Turn knob on back of mount as shown below Pull knob out and turn by hand for easy adjustment or insert 2 phillips screwdriver in end of knob and turn To adjust roll side to side tilt Turn knob on side of mount
10. t www peerlessmounts com For customer care call 1 800 865 2112 Installation to Concrete Ceilings A WARNING e Concrete must be 2000 psi density minimum Lighter density concrete may not hold concrete anchor e Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components Place projector mount assembly A on ceiling as a template and mark the center of the two mounting holes Drill two 5 16 8mm dia holes to a minimum depth of 2 1 2 64mm Attach projector mount assembly A using two concrete anchors G two flat washers E and two 14 x 2 1 2 wood screws F as shown in figure 3 1 NOTE Mounting slots on projector mount assembly allow for 30 15 of swivel adjustment before fully securing wood screws Tighten wood screws F using 3 8 10mm socket or open end wrench or phillips screwdriver until projector mount assembly A is firmly attached A WARNING Tighten wood screws firmly but do not overtighten Overtightening can damage the screws greatly reducing their holding power Never tighten in excess of 80 in Ib 9 N M A WARNING e Always attach concrete anchors directly to load bearing concrete Never attach concrete anchors to concrete covered with plaster drywall or other finishing material If mounting to concrete surfaces covered with a finishing surface is unavoidable not evaluated by UL the finishing
Download Pdf Manuals
Related Search