Home

NEC MultiSync IDC3000 User's Manual

1. REAR PANEL baban SPECIFICATIONS REMOTE 2 amu upian qa APPENDIX REMOTE CONTROL NOTES LIMITED V ARRANTY ADJUSTMENT The IDC 3000 converts NTSC video signals into scan doubled signals This scan converter can be used with a multi synchronous scan monitor or projectors having a minimum of 31 5 kHz horizontal scanning capability to provide high quality images The IDC 3000 can be also connected to a document camera conventional VCR video disc player S Video recorder or video camera FEATURES Motion adaptive 3 dimensional Y C separation circuit greatly reduces cross talk dot interference cross color Motion adaptive 3 dimensional scanning line interpolation circuit pro vides a reduction of line flicker and an increase of vertical resolution Two mode digital video noise reduction circuit greatly improves the signal to noise ratio of the signal Forced non adaptive still screen mode provides a still image without erroneous operation of the operation detection circuit This is useful with the images of document cameras etc Equipped with a demonstration split function for processing artificial interlace and switching off 3 dimensional Y C separation processing the right half of the screen PC CONTROL connector permits control of a p
2. SPLIT OFF During movie mode 2 MOVIE 2 During movie mode 3 MOVIE 3 Display color SPEIT ON u Cyan Display color All Cyan SPLIT OFF n anata inn nara Cyan Screen Display During Mode 2 Adjustment Screen Display During Mode 2 Adjustment Each press of the MODE 2 button changes the mode in a toggle Each press of the MODE 2 button changes the mode in a toggle operation and selection is made with the UP and DOWN button operation and selection is made with the UP and SPLIT button SPLIT MOVIE SPLIT MOVIE HOOK UP EXAMPLES Video equipment Laser disc player or TV tuner VIDEO 1 VIDEO 2 VIDEO 3 V DEO 4 V DEO 5 RGB THROUGH MONITOR VIDEO 1 VIDEO 2 HORIZONTAL HV POL PC CONTROL SW EBE 422232 Lo PC CONTROL S VIDEO TERMINATE EXTERNAL CONTROL Video camera or document cam Video input of an NEC MultiSync RGB inputs of projectors or moni era equipped with a VIDEO output monitor or an S VIDEO input of a tors such as NEC MultiSync pro or an S VIDEO output monitor jector 9PG 6PG EXTRA or PLUS and NEC MultiSync multimedia monitor XP37 XM37 supporting a minimum of 31 5kHz horizontal scanning frequency Personal computer QOO OO
3. Connected to the VERTICAL input jack of a monitor or projector having a 31 5 kHz horizontal scanning function 14 EXTERNAL CONTROL Connector Connections are made to this connector when controlling this unit by external control See the External Control Mode section RGB D Sub 15 mini Connector Pin Assignment Signal to be connected Red input NOTE Green input Use a signal conforming to the standard TV signal when connecting an input source e Using poor quality video tape may cause distortion on the picture Blue input GND GND Red GND Green GND Blue GND Open Sync GND GND Open H Sync V Sync Ko O I a G D co rs REMOTE CONTROL POWER d4 es ee vl 1 5 El DEO1 VIDEO2 VIDEO3 VIDEO4 V DEO B G p 5 MONITOR B A 7 SPLIT REDUCTION STILL e g NOISE REDUCTION Button Used when screen noise becomes annoying Each time this button is pressed the NR function will change as follows OFF NOISE REDUCTION 1 NOISE REDUCTION 2 Noise is reduced Noise is further reduced MOVIE Button Press to manually set the method of Y C separation and image interpo lation STILL Button Press to display still images such as those from document came
4. INDICATORS VIDEO NTSC MONITOR 1 2 3 4 RGB MOVIE STILL NOISE REDUCTION 1 2 1 2 3 14 16 17 NR Button Used when screen noise becomes annoying Each time this button is pressed the NR function will change as follows OFF NOISE REDUCTION1 NOISE REDUCTION 2 Noise is reduced Noise is further reduced MOVIE Button Press to manually set the method of Y C separation and image interpo lation STILL Button Press to display still images such as those from document cameras etc The Y C separation and image interpolation will be set for the still screen mode MONITOR Button Switches the MONITOR OUT jack output at the time of RGB input Each time this button is pressed the MONITOR OUT jack output will change as follows B VIDEO1 VIDEO2 gt VIDEO3 VIDEO4 gt VIDEOS OFF VIDEO 1 through 5 Button Switches the video input mode REMOTE Jack For service personnel only Remote Sensor Window Receives the signal from the wireless remote control VIDEO 1 2 3 4 5 Indicator Lights when the unit is switched to the video input mode with the VIDEO 1 through 5 buttons NTSC Indicator Lights when an NTSC standard signal is received IDTV processing is in operation when this indicator is lit 9 NORM SET Switch This is an adjustment switch for service personnel 10 NORMALIZE Button Sets the various adjustments to the standard settings
5. NOTE This rack mount bracket is designed for used with EIA standard racks Remove the four A screws from the IDC 3000 2 Use the screws removed in Step 1 to fasten the supplied rack mount bracket B to the IDC 3000 Mount the IDC 3000 to the rack and tighten the screws gt 482 6mm 465 1mm Rack mount bracket L o 0 o 108 0mm 1 4 1 57 15mm o 0 0 A 9 2 SPECIFICATIONS BNC input Input impedance 750 1 0 Vp p S input Y Input impedance 75Q 1 0 Vp p C Input impedance 75Q 0 28 Vp p Burst level Audio input L and R channels BNC output Input impedance 22 kQ or greater 0 5 Vrms Output impedance 75Q 1 0 0 1 Vp p with 75Q termination S output Y Output impedance 75Q 1 0 0 1 Vp p with 75Q termination C Output impedance 75Q 0 28 0 1 Vp p Burst level with 75Q termination Audio output L and R channels Output impedance 1 kQ or less 0 5 0 1 Vrms with ATT 0 dB BNC Input R G B H and V Through out Audio input L and R channels Input impedance 22 kQ or greater 0 5 Vrms BNC Output Audio output L and R channels R G and B Output impedance of 75Q 0 7 0 1 Vp p Note that the maximum deviation between R G and B is 0 05 V NOTE From the blanking level to white peak with 75Q termination HORIZONTAL and VERTICAL High impedance 3 5 Vp p 2 7 to 5 25 V H V O
6. 5V AA batteries when replacing the batteries ADJUSTMENT Adjustment of COLOR TINT SHARPNESS and SOUND 1 Press the MODE 1 button and select the mode to be adjusted Each press of the MODE 1 button will change the selection as follows c COLOR TINT SHARPNESS SOUND 2 While the indicator is on press and hold the UP or DOWN button and adjust COLOR Adjusts the density of the color TINT oreen ae Adjusts the tint SHARPNESS Adjusts the sharpness of the picture quality SOUNLD Adjusts the output level of the audio MOVIE Use the UP and DOWN buttons to select the movie mode MOVIE 1 o MOVIE 2 MOVIE 3 UP button Changes clockwise DOWN button Changes counterclockwise Y C Separation Mode Image Interpolation Mode Motion Adaptive mode __ Motion Adaptive mode Movie 3 Movie 2 Move mode lt Movie 1 Move mode The MOVIE mode functions only when the MOVIE indicator of the front panel is lit NOTE Processing is done to a Y C separated signal For this reason Y C separation mode is not effective when S VIDEO input selected Adjustment of SPLIT and MOVIE Press the MODE 2 button and select the mode to be adjusted Each press of the MODE 2 button will change the selection as follows SPLIT MOVIE While the indicator is on press the UP or DOWN button an
7. Condition e RS 232C or RS 422 Data Data length Baud tates a ee n 9600 bps Command 2 Data length 8 bits UNIT ID Parify Odd parity Command 1 Stop Dit a aaa 1 bit e Communications mode Full duplex e Command 1 Code based on the command system e UNIT ID Code allocated to each equipment Allocate 20H to the IDC 3000 Command 2 Code allocated to the main functions of the IDC 3000 Data Length Number of bytes of the data that is transmitted Data that 15 transmitted Check Sum Lower eight digits of sum total of the first byte to the byte just before the last Command Communication Sequence When external equipment such as a personal computer gives the command to the IDC 3000 the IDC 3000 returns an ACK or NAK So make sure that the external equipment receives this ACK or NAK Command sending receiving sequence Command ernal equipmen IDC 3000 PC only when accessing EEPROM The IDC 3000 returns an ACK if it has received the command correctly If it has not received the command correctly due to data error it will return a nothing Therefore when the external equipment send a command make sure that it received the ACK The IDC 3000 returns a NAK only when a WRITE error has occurred during EEPROM access commands PC CONTROL COMMA
8. Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocare the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help AVERTISSEMENT AFIN D EVITER TOUT RISQUE D INCENDIE OU D ELECTROCUTION NE PAS EXPOSER CET APPAREIL A LA PLUIE OU A L HUMIDITE DE MEME NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT SAUF SI CES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVERT EVITER D OUVRIR LE COFFRET CAR IL Y A A L INTERIEUR DES COMPOSANTS SOUMIS A UNE HAUTE TENSION POUR LES REPARATIONS S ADRESSER A UN PERSONNEL Q
9. Wood Dale IL 60191 MENO
10. ne pas le faire tomber 3 Eloigner Pappareil des endroits chauds tr s poussi reux et expos s en plein soleil 4 Eviter que des liquides et des petits objets m talliques p n trent l int rieur de l appareil En cas d accident d brancher l appareil et le confier un centre de service agr NEC 5 D brancher l appareil avant le nettoyage Utiliser seulement un chiffon doux et un d tergent doux Des a rosols et produits de nettoyage disponibles dans le commerce risquent d endommager le coffret AVERTISSEMENT Le coffret ne doit pas tre enlev par un personnel non qualifi pour faire les r glages internes La garantie devient caduque si l appareil est endommag de cette mani re De plus il y a risque d lectrocution En cas de probl mes de r paration contacter votre revendeur PART NAMES AND FUNCTIONS FRONT PANEL 2 0 REMOTE 14 LEEF e woo w uo sa tre TO EE 1 POWER Button Press to turn the unit on when the power cord is connected to an active AC power outlet NOTE After the power cord is connected to an active power outlet the unit enters the standby mode and the red STAND BY indicator is illuminated In this mode the unit can be turned on by pressing the POWER button The STAND BY indicator changes to green to show that the unit is turned on 2 POWER STAND BY Indicator Indicator LED is green when th
11. processing the right half of the screen This function is for use vvhen the NTSC indicator is lit e MOVIE Selects the Y C separation method and the image interpolation method Mode YIC Separation Image Interpolation Normal Motion adaptation Motion adaptation Movie 1 Move mode Move mode Movie 2 Move mode Motion adaptation Movie 3 Motion adaptation Move mode DOWN and UP Buitons Used to adjust or activate the item selected with the MODE 1 or MODE 2 button REMOTE CONTROL NOTES Remote Control Precautions Battery Precautions The remote control system may not function when direct sunlight or Do not use new and old batteries together strong illumination strikes the remote sensor window of the main unit Do not use different kinds of batteries together Do not place in locations where there is a high temperature or high Do not short circuit batteries heat them or throw them into a fire humidity Doing so will lead to breakdown Do not take apart the batteries When remote control buttons are pressed and held main unit operations Remove the batteries from the remote control when the remote control may not be possible is not going to be used for a long period Installing the Batteries of the Remote Control 1 Press and open the cover in the direction of the arrow 2 Install the batteries according to the and indications inside the case 3 Close the cover NOTE Use two 1
12. the serial number has been defaced modified or removed 3 Damage deterioration or malfunction resulting from a Accident misuse abuse neglect fire water lightning or other acts of nature unauthorized product modification or failure to follow instructions supplied with the products Repair or attempted repair by anyone not authorized by NECTECH Any shipment of the product claims must be presented to the carrier Removal or installation of the product Any other cause which does not relate to a product defect Burns or residual images upon the phosphor of the tubes 4 Cartons carry cases batteries external cabinets magnetic tapes or any accessories used in connection with the product HO RO 0 WHAT WE WILL PAY FOR AND WHAT WE WILL NOT PAY FOR We will pay labor and material expenses for covered items but we will not pay for the following 1 Removal or installation charges 2 Costs of initial technical adjustments set up including adjustment of user controls These costs are the responsibility of the NECTECH dealer for whom the product was purchased 3 Payment of shipping charges consequential damages so the above limitations and exclusions may not apply to you HOW STATE LAW RELATES TO THE WARRANTY This warranty gives you specific legal rights and you may also have other rights which vary from state to state FOR ALL INFORMATION TELEPHONE 708 238 7764 NEC Technologies Inc 1255 Michael Drive
13. 11 Clear Send Clearing to send when using PC 12 Clear to 3 o Request to Send Requesting to send when using PC 8 o Request to Send 9 13 o Used inside the IDC 3000 4 5 10 14 No Connection Not used 15 Signal Ground Ground PC is an abbreviation for personal computer Connection Examples for Personal Computer Control for the Two Varia D When using the PC CONTROL terminal as RS 232C tions RS 232C RS 232C PC CONTROL Request to Send 5 A ee t IDC 3000 Terminal Po eue computer Transmit Data To Receive Data of PC Receive Data 2 RS 422 RS 422 From Transmit Data of PC PC CONTROL Terminal Personal Clear to Send From Request to Send of PC Signal Ground Signal Ground of PC 2 VVhen using the PC CONTROL terminal as RS 422 Request to Send To Clear to Send of Converter or PC Request to Send To Clear to Send of Converter or PC Transmit Data To Receive Data of Converter or PC 6000 Receive Data From Transmit Data of Converter or Receive Data From Transmit Data of Converter or PC Transmit Data To Receive Data of Converter or PC Clear to Send From Request to Send of Converter or PC Clear to Send From Request to Send of Converter or PC Signal Ground Signal Ground of Converter or PC RACK MOUNTING Use the accompanying rack mount bracket to mount the IDC 3000 to the rack
14. ND LIST FOR USE WITH THE IDC 3000 PC IDC 3000 IDC 3000 PC Contents Contents Power On Power On ACK Power Off Power Off ACK Input switching Input switching ACK Example Input switching VIDEO 1 from the PC to the IDC 3000 when the address selector equals 0 PC IDC 3000 1 UA COM21 Leng Data Sum DF 20 47 01 01 48 VIDEO2 02 VIDEO 3 03 VIDEO 4 04 V DEO 5 05 RGB 06 IDC 3000 gt PC 1 UA COM2 Leng Sum 3F 20 47 00 A6 PROFESSIONAL GRAPHICS PRODUCTS LIMITED WARRANTY NEC Technologies Inc hereafter NECTECH warrants this product to be free from defects in material and workmanship under the following terms HOW LONG IS THE WARRANTY Parts and labor are warranted for 1 One Year from the date of the first customer purchase WHO IS PROTECTED This warranty may be enforced only by the first purchaser WHAT IS COVERED AND WHAT IS NOT COVERED Except a specified below this warranty covers all defects in material or workmanship in this product The following are not covered by the warranty 1 Any product with is not distributed in the U S A Canada and Mexico by NECTECH or which is not purchased in the U S A Canada and Mexico from an authorized NECTECH dealer Authorized NECTECH dealers can be identified by an NEC window decal Any dealer which does not display this deca
15. OR BNC Outputs the signals of the equipment con tor or projector having a 31 5 kHz horizon nected to VIDEO 1 through 5 tal scanning function S VIDEO Outputs an S video signal derived from AUDIO L and R RCA Connected to the audio input jacks of RGB the signal of the equipment connected to equipment VIDEO 1 or VIDEO 2 which has been divided to a luminance signal Y and a 10 HV POL Switch chrominance signal C Selects the polarity of the horizontal and vertical output signals AUDIO L and R RCA Outputs the signal of the equipment con Horizontal nected to VIDEO input 1 through 5 and the AUDIO L and R associated with the RGB input connector The selected video signal is output when RGB input has been selected and MONI TOR button is switched on Vertical Active high Active low 11 PC CONTROL SW Switch Selects the communications standard of the PC CONTROL connector RS 422 standard 9 RGB Output Connector OUTPUT DBM ae RS 232C standard RGB BNC Connected to the RGB input jacks of a monitor or projector having a 31 5 kHz 2 AC IN Receptacle horizontal scanning function Used to connect the supplied power cord HORIZONTAL BNC Connected to the HORIZONTAL input dacs ob a monitor r projector having a 31 5 13 PC CONTROL Connector 15 pin connector kHz horizontal scanning function Connect a personal computer or other control equipment VERTICAL BNO
16. OWER S VIDEO ee Connected with the S video output jack of button the external equipment OFF START After connecting the power cord to the power outlet a AUDIO L and R RCA Connected with the audio output jacks of press of front panel POWER button will switch on the external equipment the power 6 VIDEO 3 VIDEO 4 and VIDEO 5 Input Jacks INPUT 2 DISPLAY Switch VIDEO 3 4 and 5 BNC Connected with the video output jacks of ON m On screen display will appear on the monitor the external equipment OFF BL On screen display will not appear on the monitor AUDIO L and R RCA Connected with the audio output jacks of the external equipment s TERMINATE Switch VIDEO 1 and VIDEO 2 Switches the terminating resistor of the BNC input jacks H 75Q termination input OPEN High impedance input 17 RGB Input Connector THROUGH RGB D sub 15 miniature Connected with the RGB output connector of the external equipment The input signal is through output from the RGB output connector See page for pin assignment 4 BNC S VIDEO Switch VIDEO 1 and VIDEO 2 BNC 2202458 Provides the appropriate switching when the signal is input from the BNC input jacks S VIDEO Provides the appropriate svvitching when the signal is input from the S VIDEO input jack 8 MONITOR Output Jack OUTPUT H V BNC 22 Connected to the H V input jack of a moni MONIT
17. UALIFIE RISQUE D ELECTROCUTION NE PAS OUVRIR ATTENTION AFIN D EVITER TOUT RISQUE D ELECTROCUTION NE PAS ENLEVER LE COUVERCLE AUCUN DES ELEMENTS INTERNES NE DOIT ETRE REPARE PAR L UTILISATEUR NE CONFIER L ENTRETIEN QU A UN PERSONNEL QUALIFIE La fleche symbolisant le tonnerre l int rieur du AN triangle quilat ral a pour but de pr venir l utilisateur de la pr sence d une tension dangereuse non isol e se trouvant l int rieur du dispositif elle est d une intensit suffisante pour constituer un risque d lectrocution Le point d exclamation du triangle quilat ral a pour but de pr venir l utilisateur de la pr sence d importantes instructions concernant l entretien et le fonctionnement indiqu es dans la brochure accompagnant l appareil Par cons quent elles doivent tre lues attentivement afin d viter des probl mes DOC avis de conformation Cet appareil num rique de la classe B respecte toutes les exigences du R glement sur le Mat riel Brouilleur du Canada CONTENTS FEATURES aaa bina yesigi ON SCREEN DISPLAY WARNINGS AND 1 HOOK UP EXAMPLES PART NAMES AND FUNCTIONS o Using the EXTERNAL CONTROL Connector FRONT PANEL osiin rost adlie Using the PC CONTROL Connector INDICAT OPS AY nent o RACK MOUNTING
18. VOEDO 60820 Mini D SUB 15 Pin Pin No Function 3 Input switching 5 Power on off 8 Input switching 9 Input switching 14 External control on off 15 Ground NOTE Button operations of the main unit and the remote control are not possible during use of external control Using the PC CONTROL Connector 00000 VOEDO 60820 Mini D SUB 15 Pin NOTE The communication mode of the PC CONTROL terminal can be selected between RS 422 and RS 232C with the PC CONTROL SW on the rear panel When using RS 232C only pins 6 7 8 and 12 are effected Therefore nothing should be connected to pins 1 2 3 and 11 When using with a projector set the PC CONTROL switch to the 422 position Using the EXTERNAL CONTROL Connector Function Table Function Pin No 14 15 5 15 8 15 3 15 9 15 4 15 External control ON SHORT External control OFF OPEN POWER ON SHORT POWER OFF OPEN VIDEO 1 SHORT SHORT SHORT VIDEO 2 OPEN SHORT SHORT VIDEO 3 SHORT OPEN SHORT VIDEO 4 OPEN OPEN SHORT VIDEO 5 SHORT SHORT OPEN RGB OPEN OPEN OPEN PC CONTROL Terminal Use the PC CONTROL terminal when connecting to computers or other controllers Pin No 1 Signal Name Function 1 Receive Data Receiving data when using PC 6 Receive Data 2 O Transmit Data Sending data when using PC 7 o Transmit Data
19. Z8Z0W16 16109 Siou ajeq poom ueder ul pajud SAUA ILYN 9921 2 s IBo ouu5391 JIN JAN 0006 201 19H9AU09 oll ly q JAN NEC Improved Definition Converter IDC 3000 MultiSync User s Manual NEC WARNING TO PREVENT FIRE OR SHOCK HAZARDS DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE ALSO DO NOT USE THIS UNIT S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UN LESS THE PRONGS CAN BE FULLY INSERTED REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL RISK OF ELECTRIC SHOCK DO NOT OPEN TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL This symbol warns the user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock Therefore it is dangerous to make any kind of contact with any part inside of this unit This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included Therefore it should be read carefully in order to avoid any problems DOC Compliance Notice This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations WARNING This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to
20. ay During DVNR Noise Reduction Selection DVNR 1 Display characters during noise reduction selection During Noise reduction 1 selection DVNR 1 During Noise reduction 2 selection DVNR 2 Display color All cyan Screen Display During Split Mode Selection SPLIT ON AS UU UU d Display characters during split mode selection in mode 2 During split selection SPLIT ON When split is not selected Display color SPLIT ON S sans as a ant Cyan SPLIT OFF ur nu Cyan Screen Display During NORMALIZED Selection gt NORMALIZED A press of the NORMALIZED button returns the value set in MODE 1 to the initial setting value Display characters during normalize selection Display color NORMALIZED aaa Magenta Screen Display During MOVIE Mode Selection MOVIE 1 Display characters during movie mode selection During movie mode 1 selection MOVIE 1 During movie mode 2 selection MOVIE 2 During movie mode 3 selection MOVIE 3 Display color All cyan During the NTSC COLOR Adjustment COLOR CCAD Display characters during the color adjustment During NTSC apneni as uu COLOR Display color COLOR mau suyus amu Au qY Bar Normal During th
21. d adjust SPLIT Split on UP button or SPLIT button Split off DOWN button or SPLIT button SPLIT On Sets the demonstration split mode function for processing the artificial interlace and switching off the 3 dimensional Y C separation processing the right half of the screen This function is for use when the NTSC indicator is lit NOTE Processing is done to a Y C separated signal For this reason Y C separation mode is not effective when S VIDEO input selected NOTE Each adjustment is available only when the on screen appears ON SCREEN DISPLAY Screen Display During Input Signal Selection SOURCE VIDEO 1 l lllbbliblllllib Display characters during video 1 to 5 input signal selection During video 1 input signal selection SOURCE VIDEO 1 During video 1 S input signal selection SOURCE S VIDEO 1 During video 2 input signal selection SOURCE VIDEO 2 During video 2 S input signal selection SOURCE S VIDEO 2 During video 3 input signal selection SOURCE VIDEO 3 During video 4 input signal selection SOURCE V DEO 4 During video 5 input signal selection SOURCE VIDEO 5 Display color All yellow Screen Display During STILL Mode Selection r gt STILL 2 Display characters during still mode selection Display color STIL sS Lente den AMAR cyan Screen Displ
22. e TINT Center Adjustment TINT R F G Display characters during the tint adjustment Display color during the center adjustment IBU z a maa S ss Green During the TINT G Direction Adjustment TINT R G Display characters during the tint adjustment Display color during the adjustment in the G direction Tint Green During the TINT R Direction Adjustment TINT R CAE G C Display characters during the tint adjustment Display color during the adjustment in the R direction inte E A EA Green 577770 Red CE Green RZ Red During the SHARPNESS Adiustment SHARPNESS CAE Display characters during the sharpness adjustment Display color SHARPNESS Green Bar Normal sii aisrasactinceneeag s si Magenta MAX Red Min d di Green During the SOUND Adjustment SOUND Display characters during the sound adjustment Display color SOUNDA renaturigi quna nies Green Bar Nofmal nan SADA Magenta Maula uhuman nr Red 0202200000 Blue During the SPLIT Screen Selection During the MOVIE Mode Selection SPLIT ON MOVIE 1 Display characters during the split mode selection Display characters during the movie mode selection During split selection SPLIT ON During movie mode 1 MOVIE 1 When split is not selected
23. e unit is turned on When the unit is turned off this indicator is red and the unit enters the standby mode During external control the indicator is amber when the unit is turned on 3 MODE 1 Button Selects image adjustment and audio adjustment Each time this button is pressed mode 1 will change as follows r COLOR TINT SHARPNESS SOUND 4 DOWN and UP Buttons Used to adjust the item selected with the MODE 1 or MODE 2 button 15 MODE 2 Button Used to select the image system Each time this button is pressed mode 2 will change as follows SPLIT MOVIE e SPLIT Selects the demonstration split mode function for processing the artificial interlace and switching off the 3 dimensional Y C separation processing the right half of the screen NOTE The demonstration split mode function is available for the NTSC signal only NOTE Even though the NTSC indicator may not illuminate for sub standard NTSC signals such as poor quality video signals the split screen will sitill function However the demonstration split mode function has less effect because the 3 dimensional Y C separation processing is not performed unless the NTSC indicator is lit e MOVIE Selects the Y C separation method and the image interpola tion method Normal Motion adaptation Motion adaptation Movie 1 Move mode Move mode Movie 2 Move mode Motion adaptation Movie 3 Motion adaptation Move mode
24. ersonal computer Warnings and Safety Precaution The NEC IDC 3000 is designed and manufactured to provide long trouble free service No maintenance other than cleaning is required Use a soft cloth and if necessary mild detergent Do not use commercial spray cleaners which may damage the surface In case of damage arrange for repairs at an authorized NEC Service Center For operating safety and to avoid damage to the unit read carefully and observe the following instructions To avoid shock and fire hazards 1 Provide adequate space for ventilation to avoid internal heat build up If you enclose the unit in a cabinet or rack be sure there is adequate space at the top of the unit to allow heated air to rise and escape 2 Do not use the power cord polarized plug with extension cords or outlets unless the prongs can be completely inserted 3 Do not expose unit to rain or moisture 4 Avoid damage to the power cord and do not attempt to modify the power cord 5 Unplug unit during electrical storms or if unit will not be used over along period 6 Do not open the cabinet which has potentially dangerous high voltage components inside If the unit is damaged in this way the warranty will be void Moreover there is a serious risk of electric shock Mises en garde et pr cautions de s curit Le IDC 3000 NEC a t con us et fabriqu s pour assurer une longue dur e de service sans probl mes Aucun entretien a l except
25. ion du nettoyage n est n cessaire Utiliser un chiffon doux et un d tergent doux si n cessaire Ne pas utiliser des a rosols de nettoyage du commerce qui risquent d endommager la surface de cet appareil Si l appareil est endommag confier les travaux de r paration un centre de service agr NEC Pour un fonctionnement s r et afin d viter d endommager l appareil lire attentivement et respecter les instructions suivantes Afin d viter tout risque d lectrocution et d incendie 1 R server un espace libre suffisant pour la ventilation afin d viter une accumulation de chaleur interne Si l appareil est log dans un coffret ou sur une tag re s assurer qu il y a un espace libre suffisant pour la dissipation de la chaleur 2 Ne pas utiliser la fiche polaris e du cordon d alimentation avec des prolongateurs ou des prises de courant sauf si les lames peuvent tre ins r es fond 3 Ne pas exposer la pluie ou l humidit 4 Eviter d endommager le cordon d alimentation et ne pas modifier le cordon d alimentation 5 D brancher l appareil pendant les temp tes ou si l appareil n est pas utilis pendant une longue p riode 6 Ne pas ouvrir le coffret Des composants de haute tension se trouvent l int rieur Si l appareil est endommag de cette mani re la garantie devient caduque De plus il y a risque d lectrocution 7 Do not attempt to service or repair the unit NEC is not
26. l may be an unautho rized dealer If you are uncertain as to whether a dealer is authorized please contact NECTECH at 708 238 7764 HOW YOU CAN GET WARRANTY SERVICE 1 To obtain service on your product consult the dealer from whom you purchased the product or ship it prepaid to any authorized NECTECH service center 2 Whenever warranty service is required the original dated invoice or a copy must be presented as proof of warranty coverage and should be included in any shipment of the product Please also include in any mailing your name address and a description of the problem s 3 For the name of the nearest NECTECH authorized service center contact your dealer or NECTECH LIMITATION OF IMPLIED WARRANTIES All implied warranties including warranties of merchantability and fitness for a particular purpose are limited in duration to the length of this warranty EXCLUSION OF DAMAGES NECTECH S liability for any defective product is limited to the repair or replacement of the product at our option NECTECH shall not be liable for 1 Damage to other property caused by any defects in this product damages based upon inconvenience loss of use of the product loss of time commercial loss or 2 Any other damages whether incidental consequential or otherwise Some states do not allow limitation on how long an implied warranty lasts and or do not allow the exclusion or limitation of incidental or 2 Any product on which
27. liable for any bodily harm or damage caused if unqualified persons attempt service or open the cabinet Refer all service to authorized NEC Service Centers To avoid damage and prolong operating life 1 Use only with 120V 60Hz AC power supply Handle the unit carefully when moving and do not drop Locate set away from heat excessive dust and direct sunlight Protect the inside of the unit from liquids and small metal objects In case of accident unplug the unit and have it serviced by an authorized NEC Service Center 5 Unplug unit before cleaning Use only a soft cloth and mild detergent Commercial household sprays and cleaners may damage the cabinet Co D WARNING Unqualified persons should under no circumstances remove the cabinet of the unit to make internal adjustments The warranty is void if the unit is damaged in this way Moreover there is a serious risk of electric shock If you have service difficulties call your dealer 7 Ne pas essayer de r parer ou entretenir l appareil soi m me NEC ne saura tre tenu pour responsable pour toute blessure ou dommage caus par des personnes non qualifi es qui essayent de r parer ou d ouvrir le coffret Confier toute r paration un centre de service agr NEC Pour viter des dommages et prolonger la dur e de service de l appareil 1 N utiliser qu une source d alimentation de 120 V 60 Hz CA 2 Manipuler 1 avec soin pendant son d placement et
28. ras etc The Y C separation and image interpolation will be set for the still screen mode NORMALIZE Button Sets the various adjustments to the standard settings which had been set at the factory prior to shipping MODE 1 Button Selects image adjustment and audio adjustment Each time this button is pressed mode 1 will change as follows ie COLOR TINT SHARPNESS SOUND POWER Button Turns the power on or off VIDEO 1 Button Switches the unit to the video 1 input mode VIDEO 2 Button Switches the unit to the video 2 input mode VIDEO 3 Button Switches the unit to the video 3 input mode VIDEO 4 Button Switches the unit to the video 4 input mode f VIDEO 5 Button Switches the unit to the video 5 input mode RGB Button Switches the unit to the RGB input mode E MONITOR Button Used to switch on the monitor mode at the time of RGB input El SPLIT Press to activate the demonstration split mode function for processing the artificial interlace and switching off the 3 dimensional Y C separa tion processing the right half of the screen This function is for use when the NTSC indicator is lit MODE 2 Button Used to select the image system Each time this button is pressed mode 2 will change as follows SPLIT MOVIE 1 SPLIT Selects the demonstration split mode function for pro cessing the artificial interlace and svvitching off the 3 dimensional Y C separation
29. utput impedance of 75Q 1 0 0 3 Vp p High impedance 0 5 0 1 Vrms with ATT dB D SUB 15 mini connector TTL level D SUB 15 mini connector TTL level When a phono pin plug is not connected to the right channel Resolution audio input output jack the left channel audio input out t jack functi 1 audio input output jack put fack functions as a monaural audio input output fac Noise reduction When a signal is input via the RGB THROUGH connec tor the signal is looped through out Power supply Input current Dimensions Weight Supplied accessories 500 lines horizontal 450 lines vertical Approx 4 dB in NR mode 1 Approx 8 dB in NR mode 2 120 V AC 60 Hz 0 6A 43 0 W x 12 0 Hx 34 9 D cm 16 30 W x 4 23 HX 13 25 D inch 6 1 kg 13 45 lbs Remote control RD 338E two AA size batteries power cord rack mount brackets L and R Coaxial cable RGB H V 5 conductor BNC BNC e These specifications and contents are subject to change without notice Dimension indications of the scan converter unit do not include protrusions such as knobs and handles APPENDIX IDC 3000 stand alone PC CONTROL command reference You can control the main functions from external equipment such as Control Data Format personal computer using the PC CONTROL terminal The following abit gbit abit gbit abit 5 5 sections explain the interface Check Sum nterface
30. which had been set at the factory prior to shipping 11 RGB Button Switches the unit to the RGB input mode 18 MONITOR Indicator Lights when the MONITOR OUT output is selected at the time of RGB input 19 RGB Indicator Lights when the unit is switched to the RGB input mode with the RGB button 20 NOISE REDUCTION 1 and 2 Indicators Indicate the mode selected with the NR button 21 MOVIE 1 2 and 3 Indicators Indicate the mode selected with the MOVIE button 22 STILL Indicator Lights when the STILL button is switched on REAR PANEL 4 5 6 7 si 91 0 1 VIDEO2 VIDEO3 VIDEO4 VIDEOS RGB THROUG MON TOR VIDEO1 VIDEO 2 BNC HORIZONTAL HV POL PC CONTROL VERTICAL ACIN PC CONTROL O oo EXTERNAL CONTROL R S VIDEO TERMINATE 750 o m o x E lt E ZS OPEN A 9 gt 9 gt 9 gt 2 o x 2 o w _ r Pa DISPLAY POWER 81021 4 14 13 12 OUTPUT v 1 AUTO POVVER Svvitch 5 VIDEO 1 and VIDEO 2 Input Jacks INPUT ON START The power is automatically switched on when the VIDEO 1 and 2 BNC Connected with the video output jacks of power cord is connected to the power outlet the external equipment It is not necessary to press the front panel P

NEC MultiSync IDC3000 User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents