NEC LCD2000 User's Manual
Contents
1. 5 5 98 8 34 Le Quick Start To attach MultiSync LCD monitor to your system follow these instructions 1 Turn off the power to your computer 2 For the PC Connectthe 15 pin mini D SUB of the appropriate signal cable to the connector of the display card in your system Figure A 1 Tighten all screws For the Mac Connect the MultiSync LCD400 or MultiSync LCD2000 Macintosh cable adapter to the computer Figure B 1 Attach the 15 pin mini D SUB end of the appropriate signal cable to the MultiSync LCD400 or MultiSync LCD2000 Macintosh cable adapter Figure B 1 Tighten all screws NOTE To obtain the MultiSync LCD400 or MultiSync LCD2000 Macintosh cable adapter call NEC Technologies at 800 820 1230 3 For the MultiSync LCD400 Connect the 15 pin mini D SUB of the video signal cable to the appropriate connector on the back of the monitor Figure C1 For the MultiSync LCD2000 Connect the BNC cables to the appropriate connectors on the back of the monitor Connect the red BNC cable to the BNC connector on the monitor labeled R the green BNC cable to the BNC connector labeled G Sync the blue BNC cable to the BNC connector labeled B If you have a fourth BNC connector Composite Sync connect it to the BNC connector on the monitor labeled H CS If you have a fifth BN connector Vertical Sync connectit to the BNC connector on the monitor labeled VS Figure D 1 NOTE Incorrect cable con2. Control Main Menu Sub Menu EXIT Exits the O SM controls Exits to the O SM controls main menu CONTROL A Y Moves the highlighted Moves the highlighted area area up down to select up down to select one of the one of the controls controls CONTROL 4 Has no function Moves the bar in the or direction to increase or decrease the adjustment PRO CEED Proceeds to the selected Activates A uto A djust feature menu choice indicated In Display Mode opens by the highlighted area additional window RESET The currently Resets all the controls within Resets the highlighted control highlighted control to the highlighted menu the factory setting NOTE When RESET is pressed a warning window will appear allowing you to cancel the reset function Brightness and Contrast Brightness Adjusts the overall image and background screen brightness Contrast Adjusts the image brightness in relation to the background Auto Adjust Contrast Corrects the image displayed for non standard video inputs Auto Adjust MultiSync LCD400 monitor Allows automatic adjustment of the Position and Image A djust controls MultiSync LCD2000 monitor Allows automatic adjustment of the Position and Image A djust Coarse control Position Controls horizontal and vertical image position within the display area of the LCD A uto Adjust Position Automatically sets the horizontal and vertical image position within the display area of the LCD Im
3. ON position and power cord should be connected e Make certain the computer is a power saving mode touch the keyboard or mouse Display image has a green cast to it Open OSM Display Mode and press the Control button Display image is not sized properly Use the OSM Image Adjust controls to increase or decrease the Coarse total e Check to make sure that a supported mode has been selected on the display card or system being used Please consult display card or system manual to change graphics mode Selected resolution is not displayed properly Use OSM Display Mode to enter Mode Change sub menu and confirm that the appropriate resolution has been selected If not select corresponding option 11 78132391 13 5 5 98 8 34 References BBS 508 635 4706 A N EC Technologies Remote Bulletin Board System is an electronic service accessible with your system and a modem Communication parameters are 300 1200 2400 9600 14 4k 28 8k 33 3k bps no parity 8 data bits 1 stop bit Customer Service Technical Support Fax Electronic Channels 800 632 4662 508 635 4298 Internet e mail tech support nectech com Internet ftp site ftp nectech com CompuServe go NECTECH America Online keyword NECTECH W orld Wide Web http www nec com FastFacts Information INFORMATION Multisync LCD400 monitor Multisync LCD2000 monitor Glossary More Information
4. others The NEC Technologies product s discussed in this document are warranted in accordance with the terms of the Limited W arranty Statementaccompanying each product However actual performance of each such productisdependentupon factors such as system configuration customer data and operator control Since implementation by customers of each product may vary the suitability of specific productconfigurations and applications must be determined by the customer and is not warranted by NEC Technologies To allow for design and specification improvements the information in this document is subject to change at any time without notice Reproduction of this document or portions thereof without prior approval of NEC Technologies is prohibited DECLARATION OF CONFORMITY This device complies with Part15 of FCC Rules peration is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device mustacceptany interference received including interference thatmay cause undesired operation U S Responsible Party NEC Technologies Inc Address 1250 North Arlington Heights Road Itasca Illinois 60143 1298 Tel No 630 775 7900 Type of Product Computer Monitor Equipment Classification Class B Peripheral Model LA 1421JMW We hereby declare that the equipment specified above FE conforms to the technical standards as specified in the FCC Rules MultiSyncisa regis
5. surface with a lint free non abrasive cloth Avoid using any cleaning solution or glass cleaner A djust the monitor s brightness and contrast controls to enhance readability Use a document holder placed close to the screen Position whatever you are looking at most of the time the screen reference material directly in front of you to minimize turning your head while you are typing Avoid displaying fixed patterns on the monitor for long periods of time to avoid image persistence after image effects G et regular eye checkups For more detailed information on setting up a healthy work environment call N EC at 800 820 1230 NEC FastFacts information at 800 366 0476 and request document 900108 or write the American National Standard for Human Factors Engineering of Visual Display Terminal W orkstations AN SI HFS Standard No 100 1988 The Human Factors Society Inc P O Box 1369 Santa Monica California 90406 7 78132391 9 5 5 98 8 34 AM Specifications Monitor MultiSync LCD400 Notes Specifications Monitor LCD Module Diagonal 14 1 inch Active matrix thin film transistor TFT Viewable Image Size 14 1 inch liquid crystal display LCD 0 28 mm dot Native Resolution Pixel Count 1024 x 768 pitch XtraView technology 180cd n white luminence 100 1 contrast ratio typical Input Signal Video Sync ANALOG 0 7 Vp p 75 Ohms Separate sync TTL Level Ho
6. CTECH supplied components Service required as a result of third party components is not covered under this warranty Proof of Purchase will be required by N ECTECH to substantiate date of purchase Such proof of purchase mustbe an original bill of sale or receiptcontaining name and address of seller purchaser and the serial number of the product It shall be your obligation and expense to have the Product shipped freight prepaid or delivered to the authorized reseller from whom it was purchased or other facility authorized by N ECTECH to render the services provided hereunder in either the original package or a similar package affording an equal degree of protection All Products returned to N ECTECH for service MUST have prior approval which may be obtained by calling 800 632 4662 The Product shall not have been previously altered repaired or serviced by anyone other than a service facility authorized by N ECTECH to render such service the serial number of the product shall not have been altered or removed The Product shall not have been subjected to accident misuse or abuse or operated contrary to the instructions contained in the User s M anual N ECTECH SHALLN OT BE LIABLE FO DIRECT IN DIRECT IN CIDEN TAL CON SEQUENTIAL OR OTHER TYPES OF DAMAGES RESULTING FROM THE USE OF ANY NECTECH PRO DUCTO THERTHAN THE LIABILITY STATED A BO VE THESE W ARRAN TIES ARE IN LIEU OF ALL O THER W ARRAN TIES EXPRESS OR IM PLIED IN CLUDIN G BUT NOT L
7. E e Extra View ti Sync _ Eo A TO PREVENT FIRE OR SHOCK HAZARDS DO SE THIS UNIT TO RAIN OR MOISTURE ALSO DO 5 THIS UN IT S POLARIZED PLUG WITH AN EXTENSION RD RECEPTACLE RO THER OUTLETS UNLESS THE PRONGS CAN BE FULLY IN SERTED REFRAIN FROM OPENING THE CABIN ET A S THERE ARE HIGH VOLTAGE COMPONENTS INSIDE REFER SERVICIN TO QUALIFIED SERVICE PERSO NN EL AX RISK OF ELECTRIC SHOCK DO NOT OPEN JN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEA BLE PARTS IN SIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock Therefore itis dangerous to make any kind of contact with any part inside this unit This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included Therefore it should be read carefully in order to avoid any problems Canadian Department of Communications Compliance Statement DOC This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Cet appareil num rique de la classe B respecte toutes les exigences du R glement sur le mat riel brouiller du Canada C UL Bears the C UL Mark and is in compliance with Canadian Safe
8. IMITED TO THE IM PUED W ARRAN TIES OF M ERCHAN TABILITY OR FITNESS FOR A PARTICULAR PURPO SE SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR THE LIMITATION OR EXCLUSION OF LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE EXCLUSIONS ORUMITATIONS MAY NOTAPPLY TO YOU This Product is warranted in accordance with the terms of this limited warranty Consumers are cautioned that Product performance is affected by system configuration software the application customer data and operator control of the system among other factors W hile N ECTECH Products are considered to be compatible with many systems specific functional implementation by the customers of the Product may vary Therefore suitability of a Product fora specific purpose or application must be determined by consumer and is not warranted by N ECTECH For the name of your nearest authorized N ECTECH service facility contact N ECTECH at 800 632 4662 78132391 15 5 5 98 8 34 AM Mts gt E T LCD Series PROPRIETARY NOTICE AND LIABILITY DISCLAIMER The information disclosed in this document including all designs and related materials is the valuable property of NEC Technologies and or its licensors as appropriate reserve all patent copyright and other proprietary rights to this document including all design manufacturing reproduction use and sales rights thereto except to the extentsaid rights are expressly granted to
9. Macintosh Connection Healthy W ork Environment Literature amp Sales Info MultiSync Fulfillment TeleSales 78132391 14 800 366 0476 DESCRIPTIO N Detailed monitor information Detailed monitor information Definition of terms related to functions features and installation of the MultiSync monitor N ames and addresses of other groups involved in standards and features of the MultiSync monitor Detailed information on connecting the MultiSync monitor to a Macintosh Detailed information on setting up a healthy work environment DOCUMENT 142102 203101 900203 900204 153006 900108 800 NEC INFO 800 632 4636 800 820 1230 For software amp accessories 800 284 4484 5 5 98 8 34 Limited Warranty N EC Technologies Inc hereinafter N ECTECH warrants this Productto be free from defects in material and workmanship and subjectto the conditions set forth below agrees to repair or replace any part ofthe enclosed unit other than the LCD backlight which proves defective for a period of three 3 years from the date of first consumer purchase The LCD backlight is warranted for a period of one 1 year Spare parts are warranted for ninety 90 days This warranty gives you specific legal rights and you may also have other rights which vary from state to state This warranty is limited to the original purchaser of the Productand is not transferable This warranty covers only N E
10. age Adjust Coarse Adjusts the horizontal size by increasing or decreasing the Coarse setting Fine Improves focus clarity and image stability by increasing or decreasing the Fine setting NOTE The Image Adjust Fine control must be used to complete the setup of your MultiSync LCD2000 monitor Auto Adjust Coarse Fine Multisync LCD400 monitor only A utomatically adjusts the Coarse or Fine settings A uto Adjust Coarse MultiSync LCD2000 monitor only A utomatically adjusts the Coarse setting 78132391 6 5 5 98 8 34 AM T AccuColor Control System Color presets select the desired color setting If a setting is adjusted the name of the setting will change to Custom Color Gain Red Green Blue Increases or decreases Red G reen or Blue color depending upon which is selected The change in color will appear on screen and the direction increase or decrease will be shown by the color bars OSM Location You can choose where you would like the OSM control image to appear your screen Selecting O SM Location allows you to manually adjustthe position of the O SM control menu left right up or down OSM Turn Off Time The OSM control menu will stay as long as itis in use In the OSM Turn O ff Time submenu you can select how long the monitor waits after the last touch of a button to shut off the OSM control menu The preset choices are 10 20 30 60 and 120 seconds OSM Lock Out This control compl
11. at are lower than the pixel count of the LCD module text may appear choppy or lines may appear to be bold This is normal and necessary for all current flat panel technologies when displaying non native resolutions full screen In flat panel technologies each dot on the screen is actually one pixel so to expand resolutions to full screen an interpolation of the resolution must be done W hen the interpolated resolution is not an exact multiple of the native resolution the mathematical interpolation necessary may cause some lines to appear thicker than others NOTE Technical specifications are subject to change without notice 78132391 10 e 5 5 98 8 34 Monitor MultiSync LCD2000 Notes Specifications Monitor LCD Module Diagonal 20 1 inch Active matrix thin film transistor TFT Viewable Image Size 20 1 inch liquid crystal display LCD 0 31 mm dot Native Resolution Pixel Count 1280 x 1024 pitch XtraView technology 150cd n White luminence 100 1 contrast ratio typical Input Signal Video Sync ANALOG 0 7 Vp p 75 Ohms Separate sync TTL Level Horizontal sync Positive N egative Vertical sync Positive N egative Composite sync Positive N egative TTL Level Sync on Green video Positve 0 7 Vp p and sync Negative 0 3 Vp p Display Colors Analog input Unlimited number of Colors Depends on display card used Synchronization Horizontal 24 0 kH
12. ceiving antenna Increase the separation between the equipment and receiver Connectthe equipmentinto an outleton a circuitdifferentfrom thatto which the receiver is connected Consult your dealer or an experienced radio TV technician for help If necessary the user should contactthe dealer or an experienced radio television technician for additional suggestions The user may find the following booklet prepared by the Federal Communications Commission helpful How to Identify and Resolve Radio TV Interference Problems This bookletis available from the U S Government Printing O ffice W ashington D C 20402 Stock N o 004 000 00345 4 78132391 2 5 5 98 8 33 AM 1 Contents Your new NEC Technologies M ultiSync LCD monitor box should contain the following Multisync LCD Monitor with tilt swivel base MultiSync LCD400 monitor LA 1421 MW or MultiSync LCD2000 monitor 2031 Power Cord Video Signal Cable LCD400 15 pin VGA to BNC Cable LCD2000 User s Manual Registration Card XtraView M 200000 422 x 7 M ultiSync LCD400 cm monitor with Video Signal Cable amp User s Manual Remember to save your original box and packing material to transport or ship the monitor 78132391 3 XtraView MultiSync LCD2000 monitor with 15 pin VGA to BNC Cable Registration Card
13. e parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks Refer all servicing to qualified service personnel Allow adequate ventilation around the monitor so that heat can properly dissipate Do not block ventilated openings or place the monitor near a radiator or other heat sources Do not put anything on top of monitor Do notspill any liquids into the cabinet or use your monitor near water e Do not objects of any kind into the cabinet slots as they may touch dangerous voltage points which can be harmful or fatal or may cause electric shock fire or equipment failure e Do not place any heavy objects on the power cord Damage to the cord may cause shock or fire e Do not place this product on a sloping or unstable cart stand or table as monitor may fall causing serious damage to the monitor The power cable connector is the primary means of detaching the system from the power supply The monitor should be installed close to a power outlet that is easily accessible When operating the MultiSync LCD monitor with its AC220 240V worldwide power supply use a power supply cord that matches the power supply voltage of the AC power outlet being used The power supply cord you use must have been approved by and comply with the safety standards of your country Handle with care when transporting Save packaging for transporting Immediately unplug your monitor from the wal
14. each dot on the screen is actually one pixel so to expand resolutions to full screen an interpolation of the resolution must be done When the interpolated resolution is not an exact multiple of the native resolution the mathematical interpolation necessary may cause some lines to appear thicker than others NOTE Technical specifications are subject to change without notice 78132391 11 e 5 5 98 8 34 Features Analog Advantage Capable of displaying unlimited colors in a continuous spectrum providing a truer representation of color The monitor s high contrast LCD enhances color vibrancy and improves focus with no geometric distortion Wider Compatibility Because the M ultiSync LCD monitor is analog through and through it does not require special analog to digital display or interface cards but can accept RG B input directly Reduced Footprint Provides the ideal solution for environments requiring superior image quality but with size and weight limitations The monitor s small footprint and low weight allow itto be moved or transported easily from one location to another AccuColor Control System Allows you to adjust the colors on your screen and customize the color accuracy of your monitor to a variety of standards OSM On Screen Manager Controls Allow you to quickly and easily adjust all elements of your screen image via simple to use on screen menus ErgoDesign Features Enhance human ergonomic
15. etely locks out access to all O SM control functions W hen attempting to activate O SM controls while in the Lock O ut mode a screen will appear indicating the O SM controls are locked out To activate the OSM Lock Out function press PROCEED then A and hold down simulta neously To de activate the OSM Lock Out press PROCEED then A and hold down simultaneously Display Mode Display M ode provides information about the current resolution display and technical data including the preset timing being used and the horizontal and vertical frequencies NOTE Mode Change should only be used if a resolution is not recognized by the monitor The user can change to the appropriate resolution by entering the Display Mode sub menu and selecting the corresponding option Language Select O SM control menus are available in six languages Factory Preset Selecting Factory Preset allows you to reset all O SM control settings back to the factory settings The RESET button will need to be held down for several seconds to take effect Individual settings can be reset by highlighting the control to be reset and pressing the RESET button 5 78132391 7 5 5 98 8 34 AM ELFITI e Recommended Use Safety Precautions and Maintenance FOR OPTIMUM PERFO RMAN CE PLEASE NO TE THE FOLLOWING WHEN SETTING UPAND USING THE MULTISYN C LCD COLOR MONITOR DO NOTOPEN THE MONITOR There are no user serviceabl
16. hould be in the ON position Check to make sure that a supported mode has been selected on the display card or system being used Please consult display card or system manual to change graphics mode Check the monitor and your display card with respect to compatibility and recommended settings Check the signal cable connector for bent or pushed in pins Image persistence Image persistence is when a ghost of an image remains the screen even after the monitor has been turned off Unlike CRT monitors LCD monitors image persistence is not permanent To alleviate image persistence turn the monitor off for aslong as an image was displayed If an image was on the monitor for one hour and a ghost of thatimage remains the monitor should be turned off for one hour to erase the image NOTE As with all personal display devices NEC Technologies recommends using a screen saver at regular intervals whenever the screen is idle Image is unstable unfocused or swimming is apparent Signal cable should be completely attached to the computer Use the OSM Image A djust controls to focus and adjust display by increasing or decreasing the fine total W hen the display mode is changed the O SM Image Adjust settings may need to be re adjusted Check the monitor and your display card with respectto compatibility and recommended signal timings LED on monitor is not lit no green or amber color can be seen Power Switch should be in the
17. l outlet and refer servicing to qualified service personnel under the following conditions When the power supply cord or plug is damaged e liquid has been spilled or objects have fallen into the monitor e If the monitor has been exposed to rain or water e If the monitor has been dropped or the cabinet damaged e If the monitor does not operate normally by following operating instructions 78132391 8 5 5 98 8 34 AM __ CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR REDUCE EYE SHOULDER AND N ECK UE CHECK THE FOLLOW IN WHEN YOU POSITION THE MONITOR For optimum performance allow 20 minutes for warm up Adjust the monitor height so that the top of the screen is at or slightly below eye level Your eyes should look slightly downward when viewing the middle of the screen Position your monitor no closer than 16 inches and no further away than 28 inches from your eyes The optimal distance is 21 inches for the M ultiSync LCD 400 and 24 inches for the MultiSync LCD 2000 monitor Rest your eyes periodically by focusing on an object atleast 20 feet away Blink often Position the monitor ata 90 angle to windows and other light sources to minimize glare and reflections Adjust the monitor tilt so that ceiling lights do not reflect on your screen If reflected light makes it hard for you to see your screen use an anti glare filter Clean the LCD monitor
18. nections may result in irregular operation damage display quality components of LCD module and or shorten the module s life 4 Connectone end of the power cord to the MultiSync LCD Series monitor and the other e end to the power outlet Figure E 1 5 Turn on the monitor Figure F 1 and the computer 6 To complete the setup of your MultiSync LCD monitor use the following O SM controls Auto Adjust Contrast Auto Adjust Image Adjust Fine MultiSync LCD2000 monitor only Refer to the Controls section of this User s Manual for a full description of these O SM controls NOTE If you have any problems please refer to the Troubleshooting section of this User s Manual GRRE o oQmo 15 pin LT mini D SUB f 2 Mac Adapter not included IT Figure A 1 Figure B 1 78132391 4 5 5 98 8 34 AM Figure 1 Figure D 1 Multisync LCD2000 MultiSync LCD400 monitor Figure E 1 Multisync LCD2000 monitor Power Switch ia o o gt 2 gt gt 5 pin mini SUB Power Switch Figure F 1 3 5 5 98 8 34 AM 78132391 T Controls OSM On Screen Manager Controls The OSM controls on the front of the monitor function as follows 7
19. rizontal sync Positive N egative Vertical sync Positive N egative Composite sync Positive N egative TTL Level Sync on Green video Positve 0 7 Vp p and sync Negative 0 3 Display Colors Analog input Unlimited number of colors Depends on display card used Synchronization Horizontal 24 8 kHz to 60 kHz Automatically Range Vertical 56 2 Hz to 85 1 Hz Automatically Resolutions Supported Resolution based on horizontal and vertical frequencies only 720 x 400 VGA text 640 x 480 at 60Hz to 85Hz 800 x 600 at 56Hz to 85Hz 832 x 624 at 75Hz 1024 x 768 at60HZ to 75 2 Some systems may not support all modes listed cites recommended resolution at 60 Hz for optimal display performance Active Display Area Horizontal 286 mm 11 3 inches Dependent upon signal timing used Vertical 214 mm 8 4 inches and does not include border area Power Supply AC 100 120 V 220 240 V 50 60 Hz Current Rating 0 9 100 120 V 0 5 220 240V Dimensions 357 mm W x 362 mm H x 168 mm D 14 1 inches W x 14 3 inches x 6 7 inches D Weight 5 2 kg 11 5 105 Environmental Considerations Operating Temperature Humidity Feet Storage Temperature Humidity Feet 5 C to 35 C 41 F to 95 F 30 to 80 0 to 10 000 Feet 10 C to 60 C 14 F to 140 F 10 to 85 0 to 45 000 Feet Interpolated Resolutions W hen resolutions are shown th
20. s to improve the working environment protect the health of the user and save money Examples include O SM controls for quick and easy image adjustments tilt swivel base for pre ferred angle of vision small footprint and compliance with M PRII guidelines for lower emissions Plug and Play Multisync LCD400 monitor only The Microsoft solution with the W indows 95 operating system facilitates setup and installation by allowing the monitor to send its capabilities such as screen size and resolutions supported directly to your computer automatically optimizing display performance IPM Intelligent Power Manager System Provides innovative power saving methods that allow the monitor to shift to a lower power consumption level when on but not in use saving two thirds of your monitor energy costs reducing emissions and lowering the air conditioning costs of the workplace Multiple Frequency Technology Automatically adjusts monitor to the display card s scanning frequency thus displaying the resolution required FullScan Capability Allows you to use the entire screen area in most resolu tions significantly expanding image size O SM Display Screen Copyright 1997 by N EC Technologies Inc 78132391 12 5 5 98 8 34 AM Troubleshooting No picture The signal cable should be completely connected to the display card computer The display card should be completely seated in its slot Power Switch and computer power switch s
21. tered trademark of N EC Technologies Inc inthe U S and of NEC Home Electronics Ltd in Canada UK Germany France Spain Italy Austria Benelux Switzerland Denmark Finland Norway and Saudi Arabia AccuColor and ErgoDesign are registered trademarks of EC Technologies Inc inthe U S and Canada LCD400 LCD2000 XtraView IPM FastFacts Fullscan and O SM are trademarks of NEC Technologies Inc in the U S NEC is a registered trademark of NEC Corporation Copyright 1997 by NEC Technologies Inc OSM Display Screens Copyright 1997 by NEC Technologies Inc W indows is a registered trademark of Microsoft Corporation All other brands and product names are trademarks or registered trademarks of their respective owners Asa Energy Star Partner NEC Technologies has determined that this product meets the Energy Star guidelenes for energy efficiency The Energy Star emblem does not represent EPA endorsement of any product or service NEC Technologies Inc 1250 North Arlington Heights Road PartNo 78132391 Itasca Illinois 60143 1298 Printed in Japan 78132391 16 5 5 98 8 34 AM 7
22. ty Regulations according to C S A C22 2 No 950 Ce produit porte la marque C UL et se conforme aux r glements de s rele Canadiens selon CAN CSA C22 2 950 FCC Information 1 Use the attached specified cables with LA 1421 MW 1 2031 color monitors so as notto interfere with radio and television reception 1 Please use the supplied shielded power cable or equivalentto ensure FCC compliance 2 MultiSync LCD400 monitor Shielded video signal cable 3 MultiSync LCD2000 monitor Shielded 15 pin VGA to BNC cable Use of other cables and adapters may cause interference with radio and television reception 2 This equipment has been tested and found to comply with the limits for a Class B digital device pursuantto part15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment gener ates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the re
23. z to 80 kHz Automatically Range Vertical 56 0 Hz to 76 Hz Automatically Resolutions Supported Resolution based on horizontal and vertical frequencies only 720 x 400 VGA text 640 x 480 at 60Hz to 76Hz 800 x 600 at 56Hz to 76Hz 832 x 624 at 75Hz 1024 x 768 at 60Hz to 76Hz 1280 x 960 at 60Hz to 76Hz 1280 x 1024 at 60Hz to 76 7 Some systems may not support all modes listed cites recommended resolution at 60 Hz for optimal display performance Active Display Area Horizontal 399 mm 15 7 inches Dependent upon signal timing used Vertical 319 mm 12 6 inches and does not include border area Power Supply AC 100 120 V 220 240 V Q 50 60 Hz Current Rating 1 0 100 120 V 0 5A 220 240 V Dimensions 500 mm W x 483 mm x 220 mm D 19 7 inches W x 19 0 inches x 8 7 inches D Weight 10 0 kg 22 0 Ibs Environmental Considerations Operating Temperature Humidity Feet Storage Temperature Humidity Feet 5 C to 30 C 41 F to 86 F 30 to 80 0 to 10 000 Feet 10 C to 60 C 14 F to 140 F 10 to 85 0 to 45 000 Feet Interpolated Resolutions W hen resolutions are shown that are lower than the pixel count of the LCD module text may appear choppy or lines may appear to be bold This is normal and necessary for all current flat panel technologies when displaying non native resolutions full screen In flat panel technologies
Download Pdf Manuals
Related Search