NEC Dterm Analog Cordless Telephone User's Manual
Contents
1. position for pulse dialing The ability to pulse dial is dependent upon the telephone system and or the outside lines to which the D Analog Cordless is connected Charging the Battery The plastic connectors will fit together only one way Make sure the battery connector is properly aligned Before plugging the telephone line into your new telephone the rechargeable nickel cadmium battery pack must be fully charged Charge the battery for approximately 15 to 20 hours without interruption 1 Remove the handset battery cover 2 Plug the battery cable into the handset and place the battery pack inside the battery compartment 3 Replace the battery cover 4 Place the handset on the base to charge The handset can charge in either the face up or face down position Low Battery Indicator When the battery pack in the handset needs to be charged the talk battery low indicator flashes If this occurs while you are on the telephone you will hear an alert tone Complete your call as quickly as possible and return the handset to the base unit for charging Cleaning Battery Contacts To maintain a good charge it is important to clean all battery contacts on the handset and base unit about once a month Use a dry cloth or pencil eraser if necessary Do no use any liquids or solvents Beltclip Installation 1 Insert the beltclip into the holes on each side of the handset 2 Press down firmly until it clicks into the hol2. The handset microphone can be temporarily turned off muted during a telephone conversation so the person you are talking with cannot hear you You can turn the microphone back on to resume the conversation 1 While on a call press mute on the handset to turn the microphone off 2 Press mute or talk to cancel mute The microphone is turned on Flash Button The flash button allows you to access services such as Centrex call waiting call transfer conference calling and call hold 1 During the conversation press flash If accessing call waiting this allows you to answer the second caller 2 Press flash again This returns you to the previous call Storing a Number Your NEC Dt Analog Cordless telephone has 10 memory locations for storing important or frequently called telephone numbers 1 Remove the handset from the base unit 2 Press memory The talk battery low LED flashes and a beep is heard 3 Enter the telephone number you want to store up to 20 digits 4 Press memory and enter the memory location 0 9 you want to use You will hear a long beep and the talk battery low LED stops flashing indicating the number has been successfully stored If you select any keys other than 0 9 or you exceed the 20 second limit the handset beeps rapidly and no number will be stored Storing Mixed Tone Pulse Numbers If the telephone is set up for pulse dialing mixed mode numbers can be stored to easily access lon
3. NEC D e Analog Cordless User s Guide Controls and Functions 1 memory Enters or recalls numbers in mem ory 2 talk Answers or places calls 3 tone Switches to tone dialing in pulse dial mode 4 redial Redials the last number 5 pause Adds a timed pause in a memory dialing sequence 6 talk battery low An LED that indicates when the phone is in use or the battery is low OoOo ND 7 mute Turns off the handset microphone while you are using the telephone 8 flash Accesses call waiting if available transfer and conference calling 9 volume Sets both the ringer and earpiece volumes 10 channel Selects another channel for clearer reception 11 handset retainer Holds the handset in the base unit for wall mounting 12 status An LED that indicates the telephone is in once a month use or the handset is charging 13 page find Locates the handset Connecting the Base Unit Connect the telephone line cord to the TEL LINE jack on the base unit and to a telephone Connect the AC adapter to the DC IN 9V jack and to a standard 120 V AC wall outlet Set the base unit on a desk or tabletop and place the handset on the base unit 1 outlet 2 3 4 Raise the antenna to a vertical position Before plugging the telephone line into your new telephone the recharg
4. eable nickel cadmium battery pack must be fully charged Charge the battery for approximately 15 to 20 hours without interruption USING YOUR PHONE Handset On Base Remove the handset from the base AutoTalk or press talk 1 Remove the handset from the base AutoTalk or press talk Make Handset Off Base Answer Call Pick up the handset and press talk Call 1 Press talk 2 The talk battery low LED lights 2 The talk battery low LED lights 3 Listen for the dial tone 3 Listen for the dial tone 4 Dial the number 1 Remove the handset from the base AutoTalk or press talk 4 Dial the number Hang Up Return the handset to the base Press talk AutoStandby or press talk Redial 1 Pick up the handset and press talk 2 Listen for the dial tone 2 Listen for the dial tone 3 Press redial to dial the last number dialed 3 Press redial to dial the last number dialed Receiver Ringer Tone and Volume Control The telephone has two ringer tones and each tone has two volume levels While the telephone is idle continue to press volume until you hear the ringer tone and volume level you want The telephone has four receiver volume levels Low Medium High Maximum While on a call continue to press volume until you hear the volume level you want When you hang up the telephone retains the last volume setting selected Muting the Handset
5. es If you have wall mounted the base you cannot place the handset with the keypad facing inside Pull both sides of the beltclip out of the holes to remove Dt Analog Cordless is hearing aid compatible Optional Available Parts Part Description Stock Number Headset with Foam Covered Ear and Microphone 730616 Replacement AC Adapter for Base Unit 760625 Replacement String Type Beltclip 730624 Replacement Wall Mount Unit 730623 2001 NEC America Inc Document Revision 1 The material contained herein is subject to change without prior notice at the sole discretion of NEC America For more information contact Inc NEC America Inc 6555 N State Highway 161 D e is a registered trademark of NEC Corporation Irving TX 75039 2402 AutoTalk AutoStandby Random Code UltraClear Plus and AutoSecure are trademarks of Uniden America www cng nec com Corporation 750229 0 NEC
6. g distance services 1 Do Di are TS Remove the handset from the base unit Press memory The talk battery low LED flashes and a beep is heard Enter the number s to be dialed in pulse mode Press tone on the handset to enter a pause This also counts as one digit Enter the number s to be dialed in tone mode Press memory and enter the memory location 0 9 you want to use The ability to pulse dial is dependent upon the telephone system and or the outside lines to which the D Analog Cordless is connected Dialing a Stored Number 1 2 3 Remove the handset from the base unit Press talk Press memory and enter the memory location number 0 9 you want to dial If you select a memory location that does not have a number stored in it the handset beeps rapidly The number is dialed Chain Dialing After dialing a number you may be requested to enter a special access code for example when performing a banking transaction To dial the number using chain dialing 1 2 3 Remove the handset from the base unit Manually dial the telephone number Press memory and enter the memory location number 0 9 you want to dial Replacing a Stored Number When you enter the memory location number any number previously stored for the memory location is replaced Erasing a Stored Number 1 2 3 Remove the handset from the base unit Press memory twice Enter the memory location number 0 9 you wa
7. nt to erase You will hear a long beep confirming the number has been erased Selecting a Different Channel You can manually change the telephone channel for clearer operation There are 30 factory set channels from which you can select Changing channels only works when the telephone is in use 1 2 Remove the handset from the base unit Press channel The talk battery low LED flashes indicating the telephone is changing channels Continue step 2 until you find a clear channel Traveling Out of Range When you begin to move too far away from the base unit you will hear a clicking sound As you travel further out of range the voice transmission begins to break up Once you have passed the range limits of the base unit the call terminates Page Find Button Page find only works when the telephone is not in use 1 2 3 4 Press page find on the base unit for a five second beep Press and hold the page find button for a longer beep Once the handset has been located press talk on the handset to end the page find feature If you do not wish to make a call at this time press talk again to hang up Headset Installation Your telephone may be used with an optional headset To use this feature simply plug the headset into the headset jack on the handset Your telephone is ready for handsfree conversation Setting the Dial Mode Switch Place the switch in the Tone position for tone dialing or the Pulse
Download Pdf Manuals
Related Search