NEC colour monitor User's Manual
Contents
1. the video controller is built into the computer the video controller is in the form of a display card sometimes referred to as graphics card video adapter or graphics board Both configurations have a video connector or a CRT PORT on laptop computers If you are not sure which connector is the video connector refer to your computer or display card manual To attach the MultiSync LCD2110 monitor to your system p3 follow these instructions 1 Turn off the power to your computer 2 Connect the 15 pin mini D SUB of the appropriate signal cable to the connector of the display card in your computer Figure A 1 Figure B 1 Tighten all screws NOTE Some Macintosh systems require a Macintosh cable adapter 3 Remove connector cover on back of monitor Connect the BNC cables and AC adapter cable to the appropriate connectors on the back of the monitor If you are using the supplied video signal cable continue to step 4 If you are using a 15 pin mini D SUB cable not included please skip to Step 5 4 Connect the red BNC cable to the BNC connector on the monitor labeled R the green BNC cable to the BNC connector labeled G Sync the blue BNC cable to the BNC connector labeled B If you have a fourth BNC connector Composite Sync connect it to the BNC connector on the monitor labeled HS CS If you have a fifth BNC connector Vertical Sync connect it to the BNC connector on the monitor labeled VS 78134811 PM5 182. Ezz s l o lLLU TL Recommended Use E 5 Recommended Use For optimum performance please note the following when setting up and using the MultiSync LCD2110 colour monitor e DO NOT OPEN THE MONITOR There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks Refer all servicing to qualified service personnel e The optimum monitor position is facing away from direct sunlight e Allow adequate ventilation around the monitor so that heat can properly dissipate Do not block ventilated openings or place the monitor near a radiator or other heat sources Do not put anything on top of monitor e Do not spill any liquids into the cabinet or use your monitor near water e Do not insert objects of any kind into the cabinet slots as they may touch dangerous voltage points which can be harmful or fatal or may cause electric shock fire or equipment failure e Do not place any heavy objects on the power cord Damage to the cord may cause shock or fire e Donot place this product on a sloping or unstable cart stand or table as the monitor may fall causing serious damage to the monitor e Use the monitor in a clean and dry area e Handle with care when transporting Save packaging for transporting e The power cable connector is the primary means of detaching the system from the power supply The monitor should be installed close to a power outlet which is easil
3. Image Position within the display area of the LCD 25 99 12 24 2 19 PM fo o oe E 16 Controls fk Image Adjust Controls k H SIZE Adjusts the horizontal size by increasing or decreasing this setting FINE Improves focus clarity and image stability by increasing or decreasing this setting wto Automatically adjusts the H Size and Fine settings Colour Control System Five colour presets select the desired colour setting Each colour setting is adjusted at the factory R G B Increases or decreases Red Green or Blue colour depending upon which is selected The change in colour will appear on screen and the direction increase or decrease r3 will be shown by the bars Tools 4s OSM H POS BW OSM V POS You can choose where you would like the OSM control window to appear on your screen Selecting OSM Location allows you to manually adjust the position of the OSM control menu left right up or down Att ALL RESET Selecting ALL RESET when BNC input is selected allows you to reset all OSM control settings for the BNC input back to the factory settings Selecting ALL RESET when D SUB input is selected allows you to reset all OSM control settings for the D SUB input back to the factory settings Individual settings can be reset by highlighting the control to be used and pressing the RESET button 78134811 PM5 26 99 12 24 2 19 PM Ezz s l o LU TL Controls E 17 Information In
4. 99 12 24 2 19 PM Ezz s l o lLLU TL Installation E 9 Figure C 1 Place the 15 pin VGA to BNC Cable under clip A Figure D 1A Then place the 15 pin VGA to BNC cable under Clip B FigureD 1B 5 Connect the D SUB cable to D SUB connector on the back of the monitor Figure C 2 6 Replace connector cover NOTE Incorrect cable connections may result in irregular operation damage display quality components of LCD module and or shorten the module s life 7 Connect one end of the power cord to the AC Adapter and the other end to the power outlet Figure E 1 8 Turn on the monitor Figure F 1 and the computer 78134811 PM5 19 99 12 24 2 19 PM Ezz s T tlh LU TL E 10 Installation 9 To complete the setup of your MultiSync LCD monitor A Set the resolution to 1600 x1200 60 Hz B Use the following OSM controls e Auto Adjust Contrast e Auto Adjust e Image Adjust Fine NOTE Manual adjustment of the H V Position and Image Adjust H Size Fine controls may be required to complete setup of your MultiSync monitor For a full description of these OSM controls refer to the Controls section of this User s Manual 10 Refer to User s Manual in the NEC LCD Setup Software CD case for installation and operation of this software NOTE If you have any problems please refer to the Troubleshooting section of this User s Manual 78134811 PM5 20 99 12 24 2 19 PM Ezz s l o lLL
5. Ezz s i o l M TL Introduction to the NEC MultiSync LCD2110 E 1 Introduction to the NEC MultiSync LCD2110 Congratulations on your purchase of the NEC MultiSync LCD2110 true colour monitor NuCycle Plastic A special silicone compound for PC resin being extremely flame retardant safe and environmentally friendly Wide Viewing Angle Technology Allows the user to be able to see the monitor from any angle 170 degrees from any orientation Portrait or Landscape Provides full 170 viewing angles either up down left or right Analog Advantage Capable of displaying unlimited colours in a continuous spectrum providing a truer representation of colour The monitor s high contrast LCD enhances colour vibrancy and improves focus with no geometric distortion Wider Compatibility Because the MultiSync LCD monitor is analog through and through it does not require special analog to digital display or interface cards but can accept RGB input directly Reduced Footprint Provides the ideal solution for environments requiring superior image quality but with size and weight limitations The monitor s small footprint and low weight allow it to be moved or transported easily from one location to another Colour Control system Allows you to adjust the colours on your screen and customize the colour accuracy of your monitor to a variety of standards 78134811 PM5 11 99 12 24 2 19 PM Ezz S T o l M TL E 2 Introduction
6. U TL Installation E 11 ama Clip TA Figure F 1 FigureD 1A Figure D 1B H Raise and Lower Monitor Screen The monitor may be raised or lowered in either Portrait or Landscape mode To raise or lower screen place hands on each side of the monitor and lift or lower to the desired height Figure RL 1 Screen Rotation Before rotating the screen must be raised to the highest level to avoid knocking the screen on the desk or pinching your fingers To raise the screen place hands on each side of the monitor and lift up to the highest position Figure RL 1 To rotate screen place hands on each side of the monitor screen and turn clockwise from Landscape to Portrait or counter clockwise from Portrait to Landscape Figure R 1 To toggle the orientation of the OSM menu between Landscape and Portrait modes press the RESET button while OSM menu is off 78134811 PM5 21 99 12 24 2 19 PM Ezz s T tlh LU TL E 12 Installation Tilt and Swivel Grasp both sides of the monitor screen with your hands and adjust the tilt and swivel as desired Figure TS 1 Figure RL1 Figure TS 1 78134811 PM5 22 99 12 24 2 19 PM Ezz s l o lLLU TL Installation E 13 Remove Monitor Stand for Mounting To prepare the monitor for alternate mounting purposes 1 Disconnect all cables 2 Place hands on each side of the monitor and lift up to the highest position Figure RL 1 3 Pl
7. ace monitor face down on a non abrasive surface Place the screen on a 55mm platform so that the stand is parallel with the surface Figure S 1 Figure S 1 4 Press the Y portion with your index finger and at the same time slide the lower stand cover Figure S 2 Next lift up the stand remove the lower stand cover then go on to remove the upper stand cover Figure S 3 Return the stand to its original position remove the 4 screws that connect the monitor to the stand and lift off the stand assembly Figure S 4 5 Reverse this process to reattach stand NOTE Use only VESA compatible alternative mounting method CECE EE DEEEE EEE EEE EE EEE EE EEE 1 Figure S 2 Figure S 3 Figure S 4 78134811 PM5 23 99 12 24 2 19 PM fo o oe E 14 Controls Controls BNC D SUB Allows you to change between the BNC and D SUB signal inputs OSM Controls OH OSM OOOO EXIT CONTROL PROCEED RESET The OSM controls on the front of the monitor provide the following functions To access OSM press any of the control buttons lt A V or the PROCEED or EXIT button To rotate OSM between Landscape and Portrait modes press the RESET button NOTE OSM menu must be closed in order to rotate Main Menu Sub Menu EXIT Exits the OSM controls Exits to the OSM main menu CONTROL A V Moves the highlighted Move
8. d This is normal and necessary for all current flat panel technologies each dot on the screen is actually one pixel so to expand resolutions to full screen an interpolation of the resolution must be done When the interpolated resolutions is not an exact multiple of the native resolution the mathematical interpolation necessary may cause some lines to appear thicker than others NEC cites recommended resolutions at 60 Hz for optimal display performance Active display area is dependent upon the signal timing Technical specifications are subject to change without notice 78134811 PM5 29 99 12 24 4 10 PM Ezz s T tlh LU TL E 20 Troubleshooting Support Troubleshooting Support Problem Check These Items No picture The signal cable should be completely connected to the display card computer The display card should be completely seated in its slot Power button and computer power switch should be in the ON position Check to make sure that a supported mode has been selected on the display card or system being used Please consult display card or system manual to change graphics mode Check the monitor and your display card with respect to compatibility and recommended settings Check the signal cable connector for bent or pushed in pins Check that the BNC D SUB button is in the correct position Power Button does Unplug the power cord of the monitor from the AC not respond
9. dicates the current display resolution frequency setting and type of Sync signal of the monitor NOTE If the lt or gt button is pressed while TYPE is highlighted then Sync Type is switched between Separate Sync and Sync On Green OSM LOCK OUT The OSM LOCK OUT control completely locks out access to all OSM control functions When attempting to activate OSM controls while in the LOCK OUT mode a screen will appear indicating that OSM controls are locked out e To enter the LOCK OUT mode simultaneously press the PROCEED and Y button The LOCK OUT window will appear e To activate the LOCK OUT function simultaneously press and hold down the PROCEED and A button The OSM window will disappear within seconds and the LOCK OUT function will be activated e To deactivate the LOCK OUT mode simultaneously press the PROCEED and A button 78134811 PM5 27 99 12 24 2 19 PM Ezz s T tlh LU TL E 18 Specifications Multisyne LCD2110 Display 54 1 cm 21 3 inch viewable image size 1600 x 1200 native resolution Pixel Count active matrix thin film transistor TFT liquid crystal display LCD 0 27 mm dot pitch 180 cd m white luminance typical 250 1 contrast ratio typical Input Signal Video Analog 0 7 Vp p 75 Q Sync Separate sync TTL Level Horizontal sync Positive Negative Vertical sync Positive Negative Composite sync Positive Negative TTL Level Sync on Green video Positive 0 7 Vp p and sync Negativ
10. e 0 3 Vp p Display Colours Analog Input Unlimited number of colours Depends on the graphics board G Synchronisation Horizontal 24 0 kHz to 82 0 kHz Automatically Range Vertical 56 0 Hz to 76 0 Hz Automatically Resolutions Landscape 720 x 400 VGA text Supported 640 x 480 at 60 Hz to 76 Hz 800 x 600 at 56 Hz to 76 Hz 832 x 624 at 75 Hz 1024 x 768 at 60 Hz to 76 Hz 1280 x 960 at 60 Hz to 76 Hz 1280 x 1024 at 60 Hz to 76 Hz 1600 x 1200 at 60 Hz Portrait 480 x 640 at 60Hz to 76Hz 600x 800 at 56 Hz to 76 Hz 624 x 832 at 75 Hz 768 x 1024 at 60 Hz to 76 Hz 960 x 1280 at 60 Hz to 76 Hz 1024 x 1280 at 60 Hz to 76 Hz 1200 x 1600 at 60 Hz Active Display Landscape Horizontal 432 mm Area Vertical 324 mm Portrait Horizontal 324 mm Vertical 432 mm 78134811 PM5 28 99 12 24 2 19 PM MT l l ee M l Specifications E 19 Power supply AC 100 120 V 220 240 V 50 60 Hz DC 24V Current Rating 100 120V 0 9A 220 240V 0 5A DC 24V 3 3A Dimensions Landscape 498 W x 501 H x 246 D mm Portrait 417 W x 541 H x 246 D mm Hight Adjust 80mm Weight 11 5kg Operating Temperature 5 C to 35 C Environmental Humidity 30 to 80 Considerations Storage Temperature 10 C to 60 C Environmental Humidity 10 to 85 Considerations Interpolated Resolutions when resolutions are shown that are lower than the pixel count of the LCD module text may appear choppy or lines may appear to be bol
11. or shall only be used with an approved arm e g GS mark CORRECT PLACMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE SHOULDER AND NECK FATIGUE CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR e Adjust the monitor height so that the top of the screen is at or slightly below eye level Your eyes should look slightly downward when viewing the middle of the screen e Position your monitor no closer than 40 cm and no further away than 70 cm from your eyes The optimal distance of MultiSync LCD2110 is 61 cm e Rest your eyes periodically by focusing on an object at least 6 m away e Position the monitor at a 90 angle to windows and other light sources to minimize glare and reflections Adjust the monitor tilt so that ceiling lights do not reflect on your screen e If reflected light makes it hard for you to see your screen use an anti glare filter e Adjust the monitor s brightness and contrast control to enhance readability e Use a document holder placed close to the screen e Position whatever you are looking at most of the time the screen or reference material directly in front of you to minimize turning your head while you are typing e Get regular eye checkups 78134811 PM5 17 99 12 24 2 19 PM Ezz S T o l M TL E 8 Installation Installation Connection to your Personal Computer The MultiSync LCD2110 true colour monitor complements PC compatible computers Your system has one of two configurations
12. outlet to turn off and reset the monitor or simultaneously press the RESET and Power buttons Image persistence Image persistence is when a ghost of an image remains on the screen even after the monitor has been turned off Unlike CRT monitors LCD monitors image persistence is not permanent To alleviate image persistence turn the monitor off for as long as an image was displayed If an image was on the monitor for one hour and a ghost of that image remains the monitor should be turned off for one hour to erase the image NOTE As with all personal display devices NEC recommends using a screen saver at regular intervals whenever the screen is idle 78134811 PM5 30 99 12 24 2 19 PM Ezz s l o lLLU TL Troubleshooting Support Problem Cheak These Items Image is unstable unfocused or swimming is apparent Signal cable should be completely attached to the computer Use the OSM Image Adjust controls to focus and adjust display by increasing or decreasing the Fine Control When the display mode is changed the OSM Image Adjust settings may need to be re adjusted Check the monitor and your display card with respect to compatibility and recommended signal timings If your text is garbled change the video mode to non interlace and use 60Hz refresh rate LED on monitor is not lit no green or amber colour can be seen Power Switch should be in the ON posi
13. s the highlighted area up down to select area up down to select one of the controls one of the controls CONTROL lt gt Moves the highlighted area Moves the bar left left rights to select right to increase or control menus decrease the adjustment PROCEED Has no function Activates Auto Adjust and ALL RESET functions RESET Resets the highlighted Resets the highlighted contol menu to the factory contol to the factory setting setting NOTE When RESET is pressed in the main and sub menu a warning window will appear allowing you to cancel the RESET function by pressing the EXIT button 78134811 PM5 24 99 12 24 2 19 PM 78134811 PM5 SAT i Ts Controls E 15 0 0 Brightness Contrast Controls 0 BRIGHTNESS Adjusts the overall image and background screen brightness CONTRAST Adjusts the image brightness in relation to the background ato AUTO ADJUST CONTRAST Adjusts the image displayed for non standard video inputs auto Auto Adjust Automatically adjusts the Image Position H Size and Fine settings NOTE Manual adjustment of the H V Position and Image Adjust H Size Fine controls may be required to complete setup of your MultiSync monitor lt b Position Controls lt gt H POSITION Controls Horizontal Image Position within the display area of the LCD V POSITION Controls Vertical Image Position within the display area of the LCD ato AUTO Automatically sets the Horizontal and Vertical
14. sts monitor to the display card s scanning frequency thus displaying the resolution required up to 1600 x 1200 78134811 PM5 12 99 12 24 2 19 PM Ezz s l o lLLU TL Introduction to the NEC MultiSync LCD2110 E 3 FullScan Capability Allows you to use the entire screen area in most resolutions significantly expanding image size VESA Standard Mounting Interface Allows users to connect their MultiSync monitor to any VESA standard third party mounting arm or bracket Allows for the monitor to be mounted on a wall or an arm using any third party compliant device BNC D SUB Offers dual inputs allowing you to connect the monitor to one system via a BNC cable and a another system via a standard D Sub cable You can easily switch between computers with a touch of a button on the up front control panel 78134811 PM5 13 99 12 24 2 19 PM Ezz S T o l M TL E 4 Contents of Package Contents of Package Your new MultiSync LCD monitor box should contain the following ed re MultiSync LCD2110 monitor with 15 pin VGA to BNC Cable and AC Adapter NEC MultiSync LCD2110 Model LA 2141JMW P AC power cable AC Adapter Type A2440S01 Video Signal Cable 15 pin VGA to BNC User s manual NEC LCD Setup Software Pivot Software and other helpful files Remember to save the original box and packing materials to transport or ship the monitor 78134811 PM5 14 99 12 24 2 19 PM
15. tion and power cord should be connected Make certain the computer is not in a power saving mode touch the keyboard or mouse Display image has a green cast to it Select TYPE in the OSM Information menu and press the a or gt Control button Display image is not sized properly Use the OSM Image Adjust controls to increase or decrease the H Size Check to make sure that a supported mode and signal timing has been selected on the display card or system being used Please consult display card or system manual to change graphics mode or refresh rate 78134811 PM5 31 99 12 24 2 19 PM
16. to the NEC MultiSync LCD2110 OSM On Screen Manager Controls Allow you to quickly and easily adjust all elements of your screen image via simple to use on sreen menus ErgoDesign Features Enhance human ergonomics to improve the working environment protect the health of the user and save money Examples include OSM controls for quick and easy image adjustments tilt swivel pivot stand for preferred angle of viewing small footprint and compliance with MPRII and TCO guidelines for lower emissions Pivoting Stand Allows users to adjust the monitor to the orientation that best fits their application either Landscape orientation for wide documents or portrait orientation for the ability to preview a full page on one screen at one time The Portrait orientation is also perfect for full screen video conferencing Plug and Play The Microsoft solution with the Windows operating system facilitates setup and installation by allowing the monitor to send its capabilities such as screen size and resolutions supported directly to your computer automatically optimizing display performance IPM Intelligent PowerManager System Provides innovative power saving methodes that allow the monitor to shift to a lower power consumption level when on but not in use saving two thirds of your monitor energy cost reducing emissions and lowering the air conditioning cost of the workplace Multiple frequency Technology Automatically adju
17. will be viewed only intermittently Immediately unplug your monitor from the wall outlet and refer servicing to qualified service personnel under the following conditions When the power supply cord or plug is damaged If liquid has been spilled or objects have fallen into the monitor If the monitor has been exposed to rain or water If the monitor has been dropped or the cabinet is damaged If the monitor does not operate normally by following operating instructions CAUTION e Allow adequate ventilation around the monitor so that heat can properly dissipate Do not block ventilated openings or place the monitor near a radiator or other heat sources Do not put anything on top of monitor e The power cable connector is the primary means of detaching the system from the power supply The monitor should be installed close to a power outlet which is easily accessible e Use caution when carrying the monitor as the compact stand may extend automatically 78134811 PM5 16 99 12 24 2 19 PM Ezz s l o LU TL Recommended Use E 7 e Handle with care when transporting Save packaging for transporting e This LCD monitor is designed for use with a flexible arm therefore it is delivered without stand Please use the attached screws 4pcs when installing To fulfil the safety requirements the monitor must be mounted to an arm which guaranties the necessary stability under consideration of the weight of the monitor The LCD monit
18. y accessible e Use supplied AC Adapter e The inside of the fluorescent tube located within the LCD monitor contains mercury Please follow the bylaws or rules of your local municipality to dispose of this tube property e Clean the LCD monitor surface with a lint free non abrasive cloth Avoid using any cleaning solution glass cleaner or tissue paper 78134811 PM5 15 99 12 24 2 19 PM Ezz s T tlh LU TL Recommended Use For optimum performance allow 20 minutes for warm up Avoid displaying fixed patterns on the monitor for long periods of the time to avoid image persistence after image effects Avoid applying pressure to the LCD monitor surface e This MultiSync LCD monitor is integrated with OptiShield protective glass that helps protect your valuable and potentially fragile LCD panel Please note that OptiShield glass is not safety glass and is not laminated As with other glass OptiShield glass may break into sharp pieces if abused dropped or otherwise subjected to a substantial shock If OptiShield does break please use care to avoid injury MultiSync brand monitors equipped with OptiShield glass will have a reflective surface which under normal lighting conditions can cause eyestrain if viewed for long periods of time To avoid eyestrain we recommend these monitors be used in applications such as information kiosks industrial plants machinery control systems and trading floors where the screens
Download Pdf Manuals
Related Search