N-Tron 405FX-SC User's Manual
Contents
1. OSEX FXE only support Contact N TRON Corp at TEL 251 342 2164 FAX 251 312 6353 por n ton com STATEMENT This product complies with Part 15 of the Rules Operation is subject to the following conditions 11 This device may not cause harmful Interference 12 This device must accept any interference received including interference that may cause undesired operation KEY SPECIFICATIONS Physica 2v 541 em Wadi 500 12 70 cm Dept 30r 7 62 em Weight 1 2 bs 069 Note can be mounted horizontally or vertically Electrical Input Voltage 10 30 VDC Regulated Input 220mA max 8 2AVDC Steady State Current 14 0AmpIOSms max MVDC Input Ripple Less than 100 mV Input Wire Size 16 28 AWG Environmental Operating Temperature 20 C 1070C Storage Temperature 40 C t0 85 C Operating 10 90 Non Condensing Operating Aline Oto 10 000 amp Network Media hase gt Cat3 Cable 100BaseT gt Cats Cable 100BaseFX Multimode 50 62 125um Fiber Singlemode 7 10 125pm Fiber Fiber Transceiver Characteristics Fiber Length Zim Jim dine m TX Power Min Tm M M M RX Sensitivity Max iim im Ham mA Wavelength 1310mm 13100 13100 pom Multimade 77 Singloode Connectors JOJDOBGcT five RIAS UTP Ponts OST A four RIAS UTP Ports 40SFXIFXE SC or ST Duplex Port 40SFXIF2. terminal plugs as shown here wll ground the switch and the chassis The power leads fom the power source should be limited to 3 meters or less in ERAS N As an alternate users can run a drain wire amp lug from any of the Din Rail Screws or empty PEM nuts on the enclosure When using an unused ut to connect a ground lug via machine screw care should be taken ll limit penetration of ouler skin by less than Lid in Failure to do v Note Before applying power to the grounded switch you must use volt geanwumewmuce metr to vey there is no voltage difference between the powersupplys Soria sur negative output terminal and the switch chassis grounding point pos If the use of shielded cables is required it is generally recommended to only connect the shield ste end to prevent ground loops and interfere with low level signals e thermocouples RTD cables manufactured to EIA S68A or S688 specifications are required fr use with N Tron Swi MITES SHIELDED PATCH CABLE Noe Sin ee boots not show for ly purposes 1 the event all Cate patch cable distances are small Le Ethemet devices are located the same local bint andor referenced o the same cath ground it s permissible to use fully shielded cables terminated 10 Chassis ground at both ends in systems vid of low level analog sigas JRHS CONNECTOR CRIMP SPECIFICATIONS Please referen
3. N TRON 400 Series Industrial Ethernet Switches Installation Guide N TRON Industrial Ethernet Switch Installation Guide 40STX 40SFX SC A0SFX ST 40SFXE SC YY 40SFXE ST YY Where Y 40 or 30 NITRON 405FX Copyright N TRON Corp 2008 8205 University Bld Sue 4E Mobile AL 36609 USA rights reserved Reproduction adaptation translation without prior writen permission from N TRON Corp is prohibited except as allowed under copyright laws Ethernet is a registered trademark of Xerox Corporation All other product names company names logos or other designations mentioned herein are trademarks of their respective owners The information contained in this document is subject w change without notice N TRON Corp makes no warranty of any kind with regard to this material including but not limited to the implied warranties of merchantability oc fitness for a particular purpose no event shall N TRON Corp be liable for any incidental special indirect or consequential damages whatsoever included but not limited to lost profits arising of errors or omissions in this manual or the information contained herein Warning Do not perform any services on the unit unless qualified to do so Do not substitute unauthorized parts or make unauthorized modifications to the unit Do not operate the unit with the top cover removed as this could creste a sock or ite hazard Do not block t
4. XE Recommended Minimum Wiring Clearance Front 2 5 08 em Side l Osicm Suitable for use in Class I Division 2 Groups A C and D Hazardous Locations or Non hazardous only EMI EN55022 Class A FCC Part 15 Class A EMS ENS55024 1998 EN61000 42 1995 EN61000 43 1997 EN61000 4 4 1995 EN61000 4 5 1995 o ST R Certified Warranty Effective January 1 2008 N TRON products carry 3 year limited warranty from the date of purchase FE ce g esa N TRON Limited Warranty THON Cop warn hed wer a di ped wl om ts wri d maid unde customer prse pce pad fre dete pede pod t lcd wil comede propery of my enormen Ay ens prr dn ducts returned 10 N TRON porsaan o any of he package ndm and packaged prot Ter afe shipment Resp oras or damag does nt TRON anh eed tm rected N TRON Th paired or replaced tm spp ot e NTRON seen net rts ity a ater N TRON ces pendart al ric arn t N TRON frp der dr war or net ADVANCE REPLACEMENT OPTION Upon teat this pit guise advance replacement replacement dct wil be shipped vin re 3 dr veraz by N TRON Qt he product codd dene The element proce bci Josal requirements an not be valle al aos When ie proide aad cnet stash pode io N TRON ic
5. ce the illustration below for your Cats cable specifications EIA 568B je CABLE CONNECTING THE UNIT For 40SFX amp 40SEXE units remove the dust cap from the fiber optie connectors and connect the fiber optic cables The TX on the 405FX should be connected to the RX port of the far end station The on the 405 should be connected to the TX ot the far end station For 10 100 Base TX pons plug a Category 5 twisted pair cable into the RISS connector Connect the other end to the far end station Verify that the LNK LED s are ON once the connection has been completed For Switch to Switch or Switch to Repeater connections use the X port and standard Category 5 cable To connect any other other than the X Port to another Switch or Repeater se standard Category 5 crossover cable Warning Creating port to connection on the sume switch Le loop i an illegal operation and will erate broadcast storm which will crash the nctwork TROUBLESHOOTING 1 Make sure the Power LED is ON 1 Make sure the I Error LED remains OFF 3 seconds after initial power up Verify that Link LED s are ON for connected pots Verify straight through cabling used between stations Verify crossover cabling used between switches or repeaters non X Port only Verify that cabling is Category 5 for Operation Verify TX is connected to far end RX and vise versa
6. e 19 dy aer oie replacment N TRON il charge coner fore oce poet ri eR e TALIA EET TEE UR ERE E ERIS M ERE i men fea cna danas for cern eo ied toca rth do of a Ior Sart gives peep rights which ary depending all
7. he air vents on the sides the top ofthe uit Do not operate the equipment in the presence of flammable gasses fumes Operating electrical equipment in such an environment constitutes a definite safety hazard Safety Warnings ELECTRICAL SAFETY WARNING Do not disconnect while circuits unless area is known o be non hazardous WARNING Disconnect he power cable before removing the enclosure top WARNING Do not operate the unit with the top cover removed WARNING Properly ground the unit hefre connecting anything else to the unit Units not properly grounded may result in a safety risk and could be hazardous and may void the warranty See the grounding technique section ofthis user manual for proper ways to ground the uni WARNING Do not work on equipment ar cables during periods of lightning activity WARNING Do not perform any services on the unit unk s qualified to doso WARNING Do not block the air vents WARNING Observe proper DC Voltage polarity when installing power input cables Reversing Voltage polarity can cause permanent damage to the unit and void the warranty Power must be supplied by an isolating source and a 0 5 A max rated UL recognized fuse must be installed immediately before the unit LASER SAFETY 405 Only CAUTION CLASS 1 LASER PRODUCT Do not stare into the laser AOSEX 40SFXE amp 4STX Industrial Ethernet Switches The 40STX and 405FX Unmanaged I
8. ide View Unscrew amp Remove the DC Voltage Input Plugs from the side header Install the DC Power Cables into the Plug s observing polarity Plug the Voltage Input Plugs back into the side header Tightening torque for the terminal block power plug is 0 22 Nav0 162 Pound Foot AIL LED S wil ash ON Momentarily including the Error LED Verify the Power LED stays ON GREEN Verify the Error LED is OFF after a few seconds Note Only 1 plug is required to be connected to power input for minimal operation For redundant power operation and V plugs must be connected to separate DC Voltage sources Use wire sizes 25 gauge NTPS 24 13 DC 24V 1 3A N TRON SWITCH GROUNDING TECHNIQUES The grounding philosophy of any control sytem is an integral part of the design N Tron switches designed be grounded but the user has been given the Dexibily to float the switch when required The best noise immunity and emissions ie CE are obtained when the N Tron switch chasis s connected to earth ground via a drain wir Some N Tron switches have metal din rail brackets that can ground the switch if the dirai is grounded In some cases N Tron switches with metal brackets be supplied with optional plastic brackets if isolation is required rexgerauccmean Both V legs of the power input connector are connected to is chassis intemally on the Connecting a drain wire to carth ground from one of the V
9. l Upto 10 Gots Maximum Throughput Industry Standard DIN Rail Enclosure PACKAGE CONTENTS Please make sure the Ethernet Switch package contains the following items 1 ANSFN ASENEN4OSTX Ethernet Switch 2 This Installation Guide Contact your carrier if any items damaged INSTALLATION Read the following warning before beginning the installation WARNING A The 405 unt contains 1 Laser Do not stare into the laser beam ier optie connector When installing or operating the product Never install or work on electrical equipment or cabling during periods of lightning activity Disconnect the power cable before removing the enclosure top Do not operate the unit with the top cover removed UNPACKING Remove all the equipment from the packaging and store the packaging in a place File any damage claims wit the carrier While RHS ports are Autosensing the 40SFX 40SERXE Fiber Optic Port is factory configured for full duplex operation In the event half duplex operation is desired follow these steps Remove the Voltage Input Power Plugs Remove the top cover 8 screw Remove the jumper plug IPL from pins 1 and 2 Replace the top cover Proceed with the installation n Full Duplex Pins 1 and 2 shorted Half Duplex Remove jumper a onder to verify the ju
10. mper settings have been set correctly for units which have the N View option turned on you should instali N ViewOPC Server software on a PC connected to the LAN The software is freely distributed on the ProdaciCD and our web site Bp vsz on comym ope hil Once N ViewOPC is installed you should view the Ports Counter page to remotely monitor cach connected port You may find it helpful to A PrintSeteen the Port Counter information fr cach port and Paste Contr V into a Windows document for farther review Please consult your N View OPC Server Manual for additional information DIN Rail Mounting Instali the unit in a standard DIN Rail Recess the unit o allow at least 5 of horizontal clearance for fiber optie cable bend radius 27 for TX models Note This unit may he mounted horizontally or vertically install the unit to 35 mm industrial DIN Rail Place the top edge of the included mounting bracket on the back of the unit against the top Bange of he DIN Rail at a 15 angle Rotate the bottom of the unit to the Pack away rom you it snaps into place To remove the unit from the 35 mm industrial DIN Rail Apply downward force to the unit unti from the bottoms of the unit from the DIN Rall Then rotate the unit approximately and towards you to completely remove the uni Optional Mounting With the exception of the S24TX and 526FX2 all N Tron products are designed to be mounted o
11. n industry standard 35mm DIN Rail However DIN Rail mounting may not be suitable for all applications We offertwo alternative mounting solutions 900 Panel Mount Assembly P N 900 PM may he used to securely mount our 100 200 300 400 500 900 Series products 10 a panel or other flat surface Our Universal Rack Mount Kit P N URMK may be used to mount our products to standard 19 racks FRONT PANEL ar a a NITRON 405FX From Left to Right INK Link LED for Fiber Optic Port 40SEX FXE only qx Fiber Optic Transmit Po 405 Only RX Fiber Optic Receive 40SFX FXE Only ACT Activity LED for Fiber Optie Port 40 only x Crossover Uplink Port 40STX Only RsPorts Auto sensing 10 100BaseT Connections Red LED indicates controller error o Green LED when Power is connected NOTE Each RHS dit has two LED s located at the top ofeach connector The lft LED indicates LINK status nd the right LED indicates ACTIVITY LED s The tale below describes the operating modes LED Cor Description GREEN Power is Applied o Poweris OFF RED Controller HW Eror No Errors Normal Operation GREEN Link between pors ine established OFF No Link between pors GREEN Data is active between ports OFF Data is inactive between pons APPLYING POWER S
12. ndustrial Ethernet Switches support high speed layer 2 switching between poris The 40STX is an affordable 5 port unmanaged switch that is capable of auto negotiating 10 100 Mb and duplex communications The N TRON 40STX is housed in a ruggedized steel enclosure and provides 5 Category 5 compliant 10 100 BaseT connections for high performance network design and hubvrepeater upgrades The 40SEX is a 5 port unmanaged switch that has 4 ports identical o the 40STX plus an additional multimode fiber optie up link capable of 2 Kilometers of 100 Mb communications without the use of repeaters The 4OSFXE is a 5 port unmanaged switch that is similar to the 40SEX but with extended range The N TRON 405 utilizes singlemode fiber transceiver that is capable of 15 Kilometers of 100 Mb Both the 40SFX and 40SEXE utilize the IEEE compliant SC or ST duplex connector for fiber optic communications The 4 10 100Base TX utilize the R45 shielded connector AIL N TRON switches come housed in steel ruggedized Din Rail enclosure designed to withstand the most demanding industrial applications and have been fully tested and certified at industrial environmental extremes All 405 Units operate on 10 30VDC 02 Key Fe e Full EEE 8023 amp 100BASE FX Compliance e Extended Environmental Specifications o Support for Full Half Duplex Operation LED LinksActivity Status Indication f Auto Sensing Speed and Flow Contro
Download Pdf Manuals
Related Search