Moffat Turbofan SEL150CX User's Manual
Contents
1. DRAWN SP CHKD 2700 MAXIMUM ASSEMBLED HEIGHT 2900 MIN CEILING HEIGHT SIDE ELEVATION MAX RACK WIDTH SECTION ADJUSTABLE AIR DELIVERY SLOTS FOR BAKE PERFORMANCE OVER PRESSURE FLOOR A concrete or tile surface s prefered The floor area ts to be flat to within 3mm over the whole oven area WATER SUPPLY TO STEAM GENERATOR Pressure 1 0 5 Sbar 15 80psi Mains water will nat require regulating Water volume can be varied by altering jet size DRAINAGE Client to provide 4 drain pipe from steam generator to suitable receptacle or pipe to drain ACCESS INTO BAKERY Oven can be dispatched fully assembled to dimensions shown or n subassemblies to be erected in clients bakery Largest piece if partially assembled is 2130 high x 1650 wide x 1220 long Largest piece if unassembled is 2130 high x 1650 wide x 680 long OVEN FLUES 9200 ID Oven stearn vent and over pressure to be taken to atmosphere Flues from ovan to atmosphere not included in contract Note Bends or offsets in the flue restrict gas velocity and must be allowed for when designing the flue height and diameter which will be dependent on the building and lacal conditions ELECTRICAL REQUIREMENTS 3 Phase Earth and Neutral 400 415V 50Hz The approximate total kilowatt loading is Heating Elements 48kW Motors 2 42kW lt 3 CLEARANCE 50mm clearance ls required at back and sides FINISH NATURAL MAT No2. SCALE 1 35 TOLERANCE 0 Smm USED ON SEL150MX SEL1500X CHANGE No 9957 DATE 03 03 1ST ANGLE PROJ YOODICSCE FP umiren me SPEC DETAILS SEL150MX SEL150CX revo 2 oweno B25252 In line with policy to continually develop and improve its products Moffat reserves the right to change specifications and design without notice New Zealand Australia Moffat Pty Limited Moffat Limited Free Call 0800 663 328 email sales moffat co nz www moffat co nz Free Call 1800 023 953 email vsales moffat com au www moffat com au SEL150CX 0403V1
3. and improve its products Moffat reserves the right to change specifications and design without notice Australia E New Zealand Moffat Pty Limited Moffat Limited Free Call 1800 023 953 Cola ZL Free Call 0800 663 328 email vsales moffat com au son and ofna tife on email sales moffat co nz www moffat com au driven byin www moffat co nz SEL150CX 0403V1 ZT Z O lt QD ea aw Y lt Z an O sa EXTRACTION FAN OVEN VENT DUCT RECIRCULATION FAN OVER PRESSURE ELECTRIGAL ENTRY POINTS VENT CONTROL HANDLE SHOWN IN SHUT POSITION MANUAL OPTION ONLY ELEGTRIGL EQUIPMENT ACCESS PANEL DOOR CATCH MICROSWITCH INTERNAL DOOR RELEASE SAFETY LEVER 1 2 COPPER DRAIN CONNECTION AT REAR OF OVEN SUPPLY WATER FLOW JETS WATER INLET 1 4 COMPRESSION FITTING amp SOLENOID VALVE FAN VEE DRIVE FAN SHAFT BEARING FAN MOTOR 15KW RACK LIFT MOTOR 0 37kW GEARBOX 20 1 RACK DRIVE MOTOR 0 18kW GEARBOX 60 1 RACK STOPPING MICROSWITCH RACK LIFT MICROSWITCH RACK DRIVE TORQUE UMITER RECIRCULATING FAN ELECTRICAL ENTRY POINTS E gt FAN MOTOR asw EXTRACTION FAN 0200 ID OVEN STEAM VENT CANOPY EXTRACTION AND OVERPRESSURE FLUE CONNECTION DOOR SWING ARG 9957 3aios Iw 2 1 18 12 2002 UU NUI SUALE Ir IN UUUBT ASK 19820 DOOR HEIGHT 155 WATER IN DATE 18 12 2002 1820 MAX RACK HEIGHT HEATING ELEMENTS
4. TECHNICAL SPECIFICATIONS TURBOFAN 150 Electric Specification Information Model No SEL1I50CX Power 3P N E 400 415V 50 Hz 50 5kW 48kW heating 2 5kW motors Connections 2 BSP water supply connection and 2 copper drain located at rear of oven Dimensions Width 1650mm Depth 1720mm includes canopy Height 2700mm includes canopy Weight 850kg Installation Information Client to provide the following connections Oven requires direct wiring from switchboard Note element wattage may vary by 5 Water connection 2 BSP Drainage connection 2 copper drain pipe Oven supply does not include canopies and flues as required by relevant authorities Bends or offsets in the flue restrict gas velocity and must be allowed for when designing the flue height and diameter which will be dependent on the building and local conditions A flue connection is required and is not included in the contract Exhaust flue 200mm in dia canopy models 100mm dia non canopy models Clearance 50mm clearance is required at back and sides of unit Minimum 2900mm ceiling height Floor A concrete or tile surface is preferred The floor area is to be flat to within 3mm over whole floor area Access Oven is supplied partially assembled to be fully erected on site Largest piece if partially assembled 2130mm H x 1650mm W x 1220mm D Largest piece if unassembled 2130mm H x 1650mm W x 660mm D In line with policy to continually develop
Download Pdf Manuals
Related Search