Milan Technology MIL-S341X User's Manual
Contents
1. no event shall MiLAN Technology be liable for incidental or consequential damages costs or expenses arising out of or in connection with the performance of the product delivered hereunder MiLAN Technology will in no case cover damages arising out of the product being used in a negligent fashion or manner Trademarks 2000 MiLAN theMiLAN logo and MiLAN Technology are either trademarks or registered trademarks of Digi International Inc in the United States and or other countries All other trademarks are the property of their respective holders To Contact MiLAN Technology For prompt response when calling for service information have the following information ready 4 Product serial number and revision 4 Date of purchase 4 Vendor or place of purchase You can reach MiLAN Technology technical support at E mail support milan com Telephone 1 408 744 2751 Fax 1 408 744 2771 MiLAN Technology 1299 Orleans Drive Sunnyvale CA 94089 1138 United States of America Telephone 1 408 744 2775 Fax 1 408 744 2793 http www milan com info milan com Copyright 2000 MiLAN Technology PrintedintheUSA P N 90000220 Rev C AWA mY He Installation Guide MIL S341X Series TECHNOLOGY A Division of Digi International UT ee yee TL 7 10 LOOBASE TX RX MDI X MDID c iii a EET ae fan sose w 9 100BASE FX ST MMF 2Km TX RX S Pig E J E Sose on KO se L 100BASE FX SC MMF 2Km 10 100B2. to 6 4 For aworkstation PC use a swap cable pins are connected 1 to 3 2 to 6 3 to 1 and 6 to 2 MDI X 1234 5678 MDI Pin 1 RX Pin 1 TX Pin 2 RX Pin 2 TX Pin 3 TX Pin 3 RX Pin 6 Tx Pin 6 RX Figure 1 RJ 45 Pinouts Installation 1 M ake any configuration changes to the module DIP switch settings 2 Remove cover plate from M CS chassis 3 Slide module into a slot through the card guides 4 Firmly seat module into card edge connector 5 Secure module with thumbscrews located on module faceplate 6 Plug in network connections Note There is no need to power off the M edia Conversion System Diagnostic LEDs and Conditions Indicated There are four LEDs for both UTP and fiber ports 4 D Duplex On indicates Full Duplex 4 A Activity On indicates receiving packets at port 4 S Speed On indicates rate is 100 M bs 4 L LINK On indicates an active connection at port 7 pin DIP Switch MDI X MDI MDI X MDI Switch Switch E LEDs E 45 RJ 45 RJ Connector Connector Figure 2 Inside of the MIL S3410 Dip Switch Features Figure 2 Speed and H alf Full Duplex or Auto N egotiation may be manually selected using the seven position DIP switch All switches must bein the up position to utilize SN M P feature selection Fiber ports operate at 100M bs only Port 1 is on the left Port 2 is on the right P Speed Duplex Duplex Packet size
3. 413 3414 4 15Km of single mode optical fiber for M IL S3413 15 53414 15 4 40Km of single mode optical fiber for M IL S3413 40 4 70Km of single mode optical fiber for M IL S3413 70 4 100K m of single mode optical fiber for M IL S3413 100 M ulti mode fiber 2Km Single mode fiber 15Km 4 1300nm wavelength 4 1300nm wavelength 4 62 5 125 micron diameter 4 9 125 micron diameter 4 Launch power 19dBm minimum 4 Launch power 15dBm 4 31dBm receive sensitivity 4 31dBm receive sensitivity Single mode fiber 40K m Single mode fiber 60K m 4 1300nm wavelength 4 1550nm wavelength 4 9 125 micron diameter 4 9 125 micron diameter 4 Launch power 4dBm minimum 4 Launch power 0dBm minimum 4 34dBm receive sensitivity 4 37dBm receive sensitivity Single mode fiber 100K m 1550nm wavelength 9 125 micron diameter Launch power 1 8dBm minimum 37dBm receive sensitivity HAHAHA MDI X MDI Switch Figure 1 The M DI X M DI switch allows for quick configuration of the 100BASE TX port Cables used when the switch is in the M DI X position the left position 4 For a hub repeater use a swap cable pins are connected 1 to 3 2 to 6 3 to 1 and 6 to 2 4 For a workstation PC use a straight through cable pins are connected 1 to 1 2 to 2 3 to 3 and 6 to 6 Cables used when the switch is in the M DI position the right position 4 For ahub repeater use a straight through cable pins are connected 1 to 1 2 to 2 3 to 3 and 6
4. ASE TX M IL S3413 provides 10 100BASE T X to 1OOBASE FX MMF with SC connector M IL S3413 15 provides 10 100BASE TX to 100BASE FX SM F with SC connector M IL S3413 40 provides 10 100BASE TX to 100BASE FX SM F with SC connector M IL S3413 60 provides 10 100BASE TX to 100BASE FX SM F with SC connector M IL S3413 100 provides 10 100BASE TX to 100BASE FX SM F with SC connector sina a ae Hots v TAa 14 100BASE FX MT RJ 10 100BASE TX MMF 2Km M IL S3414 provides 10 100BASE TX to 100BASE FX MMF with MT RJ connector M IL S3414 15 provides 10 100BASE T X to 1OOBASE FX SMF with MT RJ connector The MIL S341X series are Ethernet media and rate converter modules for use in M iLAN Technology s M edia Conversion System M CS master and slave management modules can access the M IL S341X series to implement features and monitor status The series provides packet switch functions between 10M bps and 100M bps using store and forward architecture at full wire speed They also support auto negotiation on a per port basis more than 8K MAC addresses Packet buffer memory of 2M bytes backpressure in half duplex mode and VLAN Tag packet size feature To maximize the fiber cable distance use one meter of CAT 5 UTP cable when connecting directly to a node subject to fiber budget of 16dBm and collision domain restrictions In full duplex environments use up to 100m of CAT 5 UTP and 4 2Km of multi mode optical fiber for MIL S3412 3
5. Regulatory Approval 4 FCC ClassA UL 1950 CSA C22 2 Number 950 EN 60950 CE EN 55022 Class B EN55024 4 4 4 4 NOTE To comply with EN 5502 Class B shielded data cable is required Canadian EMI Notice This Class A digital apparatus meets all the requirements of the Canadian Interference C ausing Equipment Regulations Cet appareil numerique de la classe A respecte toutes les exigences du R glement sur le mat riel brouilleur du Canada European Notice Products with the CE M arking comply with both the EM C Directive 89 336 EEC and the Low Voltage Directive 73 23 EEC issued by the commission of the European Community Compliance with these directives implies conformity to the following European N orms 4 EN55022 CISPR 22 Radio Frequency Interference 4 EN50082 1 IEC 801 2 3 4 Electromagnetic Immunity 4 EN60950 IEC 950 Product Safety Five Year Limited Warranty MiLAN Technology warrants to the original consumer or purchaser that each of it s products and all components thereof will be free from defects in material and or workmanship for a period of five years from the original factory shipment date Any warranty hereunder is extended to the original consumer or purchaser and is not assignable MiLAN Technology makes no express or implied warranties including but not limited to any implied warranty of merchantability or fitness for a particular purpose except as expressly set forth in this warranty In
Download Pdf Manuals
Related Search