Miele KWT1601VI User's Manual
Contents
1. m Align the custom doors with a level Installation Note Do not twist or jam the appliance inside the niche When unscrewing the height adjustable feet proceed gradually alternating between left and right The adjustment of the rear feet is aided if the appliance is lifted at the rear tipped forward slightly If using a wooden beam as an alternative anti tip device rotate the appliance all the way toward the wooden beam Do not use a power tool to adjust the rear feet Attaching the appliance to the installation niche m Screw the attachment plate lugs 9 to the overhead furniture fixtures If there is no way to attach the top of the appliance it can be attached to the sides of the installation niche m Pull out the plate side lugs 9 m Secure the attachment plate side lugs If there is a fairly large gap above the appliance cut a wooden beam to fit exactly and place it in the gap 51 Installation m Place the second filler strip on the peg and press both filler strips together m Insert both filler strips into the installation space above the appliance until they click into place ag 4mmx15mm SSD m lf necessary shorten the filler strip to the required height 3 gt m Place the 2 strips on top of each dee other m Insert the filler strip until you hear it click into place 22. m Remove the cover over the filter use a screwdriver if necessary m Remove the old filter 2 and replace with a new active charcoal filter m Replace the cover over the new filter Cleaning and care Changing the light bulbs Do not remove the light covers for the display lighting Should the lighting covers be damaged or need to be removed due to damage do not look directly or with an optical instrument at the lighting Interior lighting The lighting automatically switches off after the door has been open for approx 5 minutes This is not a fault After the bulb has cooled for a short time it will turn on again If the light does not come on when the door is opened briefly the light bulb should be changed m Use the main switch to turn the appliance off To reduce the risk of electric shock disconnect the appliance from the power supply by unplugging or tripping the circuit breaker q iz m Turn the light cover counterclockwise and pull out Never touch a halogen bulb with bare fingers When inserting a glass halogen bulb always hold with a soft cloth m Pull the defective light bulb from the socket m Place the new bulb in the socket Halogen bulb type 5 W 12 V socket G 4 m Put the light cover back on and turn clockwise into place Restore power to the appliance 27 Frequently asked questions With the aid of the following guide minor problems c
3. m Open the appliance door For a side by side combination the filler strips from both appliances are put together to form one long filler strip amp m Screw the attachment plate lugs 43 to the adjacent furniture fixtures With side by side combinations only the external side of the appliances can be secured to the niche m Take the peg from the side by side merging kit and insert it halfway into the filler strip rail on the left side appliance 52 Installation Preparing the custom door m Open the appliance door m Unscrew the installation supports from the appliance door m Measure the distance X between the a bracket and the overhead a Loosen the remaining screws from furniture fixtures the strips 49 on each side of the door then remove m Loosen the two nuts i f Set aside the nuts you will need m Set aside the screws and side strips them again later 8 you will need them again later i i m With the inside facing up lay the m Take off the light switch cover custom door on a stable surface to m Close the appliance door avoid scratch marks place some plastic or a cloth on the surface 53 Installation m Mark the distance X on the back side of the custom door m Also calculate and mark the center of the custom door Y m Remove the mounting frame from the appliance door and position it according to the markings on the custom door m Pre drill the h
4. 43 C otherwise malfunctions may Occur If installation next to a heat source is unavoidable use a suitable insulating plate or observe the following minimum distances from the heat source 1 8 cm from an electric cooktop or oven 12 30 cm from a gas cooktop or oven 35 Installation Base A fully loaded appliance is very heavy The load bearing capacity of your floor must meet the following requirements KWT 16x1 Vi 704 Ibs 319 kg To ensure that the appliance is installed securely and functions properly the base must be flat level and made of a hard rigid material If in doubt contact Miele Furniture fixtures The new appliance will be mounted securely to adjacent and overhead furniture fixtures For this reason it is essential that all attachable furniture fixtures are connected securely to the base or the wall by suitable means Ventilation The air intake and outlet must not be blocked or covered in any way They also need to be dusted cleaned on a regular basis 36 Installation niche To ensure safe trouble free installation and the best possible cosmetic result check to be sure that the installation space complies with the installation dimensions See Niche dimensions The side walls of the installation cavity must be plumb The minimum thickness of the side walls and the top wall must be 5 8 16 mm The minimum thickness of the toe kick p
5. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance P Do not use any oils or grease on the door seal as these will cause the seal to deteriorate and become porous with time P Do not block the ventilation gaps in the plinth or the top of the appliance housing unit as this would impair the efficiency of the appliance increase the electricity consumption and could cause damage to the appliance P Never use a steam cleaner to clean the appliance Pressurized steam could damage electrical components and cause a short circuit P Do not use any electrical equipment inside the appliance Danger of injury IMPORTANT SAFETY INSTRUCTIONS Disposal of your old appliance P Before disposing of an old appliance first make the door latch or lock unusable P Take off the door P Leave the shelves in place so that children may not easily climb inside P Consult with your municipal policy on recycling P Be careful not to damage any part of the pipework while awaiting disposal by puncturing the refrigerant channels in the evaporator bending any pipework scratching the surface coating Splashes of refrigerant can damage the eyes P Your old refrigerator may have a cooling system that used CFCs chlorofluorocarbons CFCs are believed to harm stratospheric ozone If you intentionally release this CFC refrigerant you can be
6. Humming noise made by the These noises are not a compressor This noise can fault get louder for brief periods The noise of the when the motor is switching compressor and the on coolant circulating in the Blubb blubb A gurgling noise can be system is unavoidable heard when coolant is circulating through the pipes Click Clicking sounds are made when the thermostat switches the compressor on and off Sssrrrrr On multi zone and frost free appliances you can sometimes just hear the movement of air circulating inside the appliance Rattling vibrating The appliance is uneven Realign the appliance using a level by raising or lowering the screw feet underneath the appliance The appliance is touching another appliance or piece of furniture Move it away Drawers baskets or shelves are unstable or sticking Check all removable items and refit them correctly Bottles or containers are unstable or knocking against each other Separate them The transport cable clips are hanging loose at the back of the appliance Remove the clips 30 After sales service In the event of a fault which you cannot easily fix yourself please contact the Miele Technical Service Department at the address on the back of this booklet When contacting the Technical Service Department please quote the model and serial number of your appliance given on the data plate inside
7. Danger of suffocation 34 Disposal of an old appliance Old appliances contain materials that can be recycled Please contact your local recycling center about the possibility of recycling these materials Before discarding an old appliance disconnect it from the electrical supply and cut off the power cord to prevent it from becoming a hazard Installation J In areas with a tropical climate over 100 F 38 C and more than 70 air humidity the wine cooler must only be operated in air conditioned locations Otherwise the function of the machine cannot be guaranteed Have the appliance installed by a qualified technician according to the enclosed installation instructions NWARNING This appliance is top heavy and must be secured to prevent the possibility of tipping forward Anti tip protection is required Keep the door closed until the appliance is completely installed and secured as per the installation instructions Empty weight of your machine KWT 16X1 Vi 337 Ibs 153 kg Installation site The appliance should be installed in a dry well ventilated room Do not install the appliance outdoors in an environment with dripping water in rooms which are at risk of frost The installation location should not be exposed to direct sunlight nor near a heat source such as an oven radiator etc The ambient temperature should not drop below 55 F 13 C or rise above 110 F
8. appears in the display m Touch the access button 8 to confirm m By touching the V button you can either increase or decrease the humidity inside the unit B B lower humidity B 1 higher humidity B return to menu m Touch the access button 8 to confirm the setting m Tap the V button until a ce appears in the display m Touch the access button You have left the Custom settings mode When you are in the Custom settings mode the door alarm is turned off automatically Once the door is closed itis reactivated 20 If you have selected a higher humidity setting the fans will cut in This is to ensure that the humidity is uniformly distributed throughout the interior Whenever the unit door is opened the fans will automatically switch off temporarily Air exchange through the activate charcoal filter External air passes through the filter before entering the unit The active charcoal filter ensures that only clean odor free air enters the unit creating additional protection against odor contamination The filter will need to be changed periodically or when odors are present in the unit See Cleaning and Care Active charcoal filter for more information Storing wine Storage tips Always unpack bottles do not store wine in crates or boxes Always lay bottles on their side for storage This keeps the corks moist from the inside preventing air from entering
9. electrical components and cause a short circuit Do not allow water to get into the electronic unit or lights Before cleaning m Use the main switch to turn the appliance off completely The main switch is located on the right side underneath the control panel m Unplug the power cord m Remove any bottles from the appliance and store it in a cool place m Take out any removable parts e g shelves Cleaning the interior m lt is recommended to clean the interior once a month m Use a mild solution of warm water and liquid dish soap m Clean the wooden racks with a damp cloth Do not allow the racks to become too wet m After washing wipe down the interior and accessories with a clean wet cloth then dry with a soft cloth Leave the appliance doors open for a short time so the moisture can evaporate 25 Cleaning and care Ventilation slits m Check the ventilation slits regularly Remove any dirt dust with a vacuum cleaner or brush Clean as needed Door seals Do not use any oils or grease on the door seals as these will cause the seals to deteriorate and become porous over time m Clean the door seal with water only and dry thoroughly After cleaning m Return all bottles to the appliance m Insert the plug into the power outlet and turn on the appliance at the main switch 26 Active charcoal filters Replacement filters are available from Miele x
10. factory pre set to 30 minutes display light m Tochange this time setting press and hold the Display light sensor button for 2 seconds The set time in minutes appears in the display NAA d 1 Use the V and buttons next to the display to change the duration of the lighting in increments of 15 minutes You can set the lighting to last for 15 30 45 60 75 or 90 minutes m To confirm the setting touch the access button until all the displays go out If the door is closed before the set time is completed the lighting duration starts over again from the beginning 23 Defrosting During normal operation condensate and frost can form on the rear wall of the refrigerator and drawers You do not need to remove this build up it will defrost and evaporate automatically with the heat generated by the appliance 24 Cleaning and care To reduce the risk of electrical shock disconnect the appliance from the power supply by shutting off the power main tripping the circuit breaker or unplugging the power cord before maintenance Never use cleaning agents containing abrasive substances such as sand soda acids chlorides or chemical solvents Non abrasive cleaning agents are also unsuitable as they can cause matte areas to appear Avoid getting water on the solid wood facing or the shelves Do not use a steam cleaner to clean this appliance Pressurized steam could penetrate
11. m Mark the holes through the anti tip brackets 2 on the floor of the installation niche m Set the brackets aside Assure that there are no electrical wires or plumbing in the area which the screws could penetrate risk of injury and damage m Drill pilot holes 1 8 3 mm for the 5 x 60 mm wood screws 1 16 2 mm for the 4 x 15 mm wood SCrews m lightly secure the anti tip brackets in the niche Be certain that the screws penetrate through the flooring and into the wall plate a minimum of 3 4 19 mm 47 Installation Securing an alternative anti tip device If the anti tip brackets cannot be attached securely an alternative anti tip device can be used Ensure that there is no give between the appliance and the anti tip device If possible always screw the wooden beam to existing studs M m Cut a wooden beam cross section min 3 x 4 75 mm x 100 mm to the required length The length is equal to the width of the installation niche If the installation cavity is deeper than the appliance select a beam which has a larger cross section or attach two beams 48 The beam must cover the appliance by at least 2 50 8 mm m Mark the installation height lower edge of the beam on the rear wall of the niche m Select screws according to the thickness of the wooden beam Example 3 12 89 mm screw for 2x4 beam m Determ
12. on the electronic board NC NO Com NC normally closed Com common NO normally open Switching capacity 120 V 250mA 30 V 1A m Continue with the appliance installation 46 Preparing the installation niche Keep the appliance doors closed until it is securely fastened in the niche Tipping hazard If the installation niche is deeper than the appliance a solid wooden beam can be placed behind the anti tip brackets 2 so the appliance can be securely attached to the base or wall The length of the wooden beam should be to the width of the installation space If possible always screw the wooden beam into existing studs on the rear panel of the niche Mounting Accessories The mounting accessories needed for installing the appliance into the niche are included in the packaging Several plastic bags are included which are numbered alphabetically The bag needed for each step will be marked with its respective letter m Use the included Torx screwdriver to tighten the screws Installation Anti tip brackets The anti tip brackets help keep the appliance safely secured to the installation niche to prevent tipping Two anti tip brackets are recommended for each appliance or appliance combination side by side The distance D between the anti tip brackets 2 is the width of the appliance m Position the anti tip brackets 2 on the left and right walls of the appliance niche
13. racks always be left in the pre set positions This makes optimal use of the interior space Never stack bottles on the wooden racks Only the bottom most level in Sore EL m each temperature zone can support a stack of bottles remove the wooden rack m Lay the wine bottles in the display rack so that they touch the wooden guide rail Maximum capacity m To remove the display rack pullitup The unit can hold approx 102 bottles and out then attach it to the rear 0 75 I position on the wooden rack The bottles can now be stored on the wooden rack in the usual manner Additional display racks are available from Miele 22 Storing wine Display lighting The display lighting can be turned on if you wish the bottles to be lit up even when the door is closed be m Touch the access button so it turns yellow Turning on display light m Touch the Display light sensor button so that it turns yellow The display lighting will now remain on in the 2 lower temperature zones even when the door is closed When the door is open the interior lighting also comes on in all three temperature zones Turning off m Touch the Display light sensor button so that it turns white The display lighting is now turned off When the door is closed the interior is dark and when the door is opened the interior lighting comes on Duration of the display lighting The display lighting is
14. the appliance MieleCare USA only MieleCare our Extended Service Contract program gives you the assurance of knowing that your appliance investment is covered by 5 years of worry free ownership MieleCare is the only Extended Service Contract in the industry that guarantees repairs by a Miele Authorized Service Provider using genuine Miele parts Only genuine Miele parts installed by factory trained professionals can guarantee the safety reliability and longevity of your Miele appliance Please note that unless expressly approved in writing by the Miele Ser vice department Extended Service Contracts offered by other providers for Miele products will not be recognized by Miele Our goal is to prevent unauthorized and untrained service personnel from working on your Miele products possibly doing further damage to them you and or your home To learn more about MieleCare Extended Service Contracts please contact your appliance dealer or visit us online at http miele com mielecare 31 32 sump Installation instructions To prevent accidents and machine damage read these instructions before Installation or use Caring for the environment Disposal of packing materials The cardboard box and packing materials are biodegradable and recyclable Please recycle Ensure that any plastic wrappings bags etc are disposed of safely and kept out of the reach of babies and young children
15. touched the button sound can be turned off m Touch the access button so it turns yellow N od m Touch the sensor button for any temperature zone so it turns yellow m Note the position of the V button but do not touch m Touch the access button J again so it turns white Only the access button J is visible m Place one finger on the position of the V button and hold the V button will not be visible 12 m While holding down the V button press the access button J once Keep holding the V button down until the following appears in the display approx 5 seconds v L m Tap the V button until 6 appears in the display m Touch the access button J to confirm m By touching the V button you can choose between b U Button sound is off 67 Button sound is on b Return to menu m Touch the access button J to confirm the setting m Tap the V button until you see c in the display m Touch the access button 8 You have now left the Custom settings mode When you are in the Custom settings mode the door alarm is turned off automatically Once the door is closed it is reactivated Settings Turning off for longer periods of time If the appliance is not going to be used for an extended time for example during a vacation some precautions should be taken m Turn the appliance off at the main switch m Unplug the appliance m Clean the interior m Leave the door
16. with partition using the Merging Kit 2 d The minimum thickness of the partition is 5 4 16 mm If there is a partition with a thickness from 5 16 mm to 6 160 mm between the adjacent appliances then each appliance should be individually installed within its own niche using the mounting accessories included The Merging Kit will also be needed The Merging Kit is available from Miele Installation with partition without using the Merging Kit If there is a partition with a thickness of more than 6 160 mm between the adjacent appliances then each appliance should be individually installed within its own niche using the mounting accessories included the Merging Kit is not necessary 38 Side panels If one side of the appliance is visible a side panel must be used The side panel must be firmly secured to the wall the floor and the overhead furniture fixtures before the appliance is placed in the cavity The dimensions of the side panel are taken from the opposite wall of the installation space During installation ensure that the cavity is square and the measurements are correct Adjusting the door opening angle optional accessory Depending on the installation site it may be necessary to adjust the door opening angle to 90 m Open the door m Insert the banking pin through the holes and drive in with a hammer Dimens
17. DUDS LL 27 Frequently asked questions 28 After sales service olli lille 31 Caring for the environment 0 00 00 cece eee 34 Contents Installation as eod bode pono he Shee bP Aged ie bie SA oth d 35 IistallatiOR Sleeps 5 a dae hated pen Rus pi Ron Bae ea 35 SEEN 36 Furniture fixtureS 202 se tsk hes 36 Custom door panels rss naa nee en aee qe a A ri 36 Iristallation optloriS aco ee kta ee e awe A E de ea ee Pees dae 37 Adjusting the door opening angle optional accessory 38 DIMENSI NS sss ELE Pedo m a Pa EM eee y ees 39 Door dimensions open min 90 2 ee 39 Installation 0 6 iilii RI knne 42 Before you DEgQIn Li 42 RemoteVision module installation o 44 Home Security System HSS nia bas e E a 45 Preparing the installation niche 0 46 Sliding the appliance into the installation niche 49 Aligning the appliance 0 I 50 Attaching the appliance to the installation niche 51 Preparing the custom door 53 Attaching and aligning the custom door front 54 Electrical connection 59 RemoteVision optional accessory 0 60 Accessing the RemoteVision control panel 61 IMPORTANT SAFETY INSTRUCTIONS When using the appliance follow basic safety precautions including the following Read all instructions before installation and use to prevent accidents and machine damage Thi
18. Miele Operating and Installation Instructions Wine Storage Unit KWT 1601 Vi KWT 1611 Vi To prevent accidents en US CA and appliance damage read these instructions before installation or use M Nr 07 682 490 Contents IMPORTANT SAFETY INSTRUCTIONS 220020055 4 Guide to the wine storage unit 7 Before USC sucesor yea dae nena ee EEG e hee a oce 9 Before using for the first time 9 Turning the appliance On Off 0 9 Settings css eo baa a ot 10 Usirig the sends e se i prealpi ina 10 Custom sSeNlllgss s dei ia LL Ri ia 11 Turning the button sound On Off 2 00 00 0 0 0c ee 12 Turning off for longer periods of time 13 Alarm key an tae Ge Beda Se pee beeen de 14 Temperature alam iaia ete x tine aerate eed REOR dee aa ee ee ode 14 OOK aA ERE ia PL 14 Optimum temperature and air quality 15 Setting the temperature 15 unie ape lago iaia iii Pa na 19 Storing WINE ei ici peer ed Pe eee 21 WoodertreckKs sas a dca yd RN i Pal a ate oed ia e 21 Bottle display Tac Kus ig aot ci ar e dem d AR eR afe 22 Maximum capacity 22 Display lighting sace aret roe Rene ata eta ia dure 23 Defrostingj ji eem s onde posue Ru RR edo Ego SUR mee daw p 24 Cleaning and care 25 Cleaning the interiori eres x et a ia don gs ud uu tes x 25 VentllatiOnislits ersi ood RERO Co De xu patte t ere OR a bob ee OE a eet E 26 POIS aE ori TITOLI 26 Active charcoal filters 26 Changing the light
19. Store similar wine varieties beside each other on the same shelf to avoid restacking and the need to disturbed other bottles Before serving ros and red wine bottles should spend at least two hours upright and open to reach optimal drinking temperature Sparkling wine and champagnes should be chilled briefly in the refrigerator before serving Remember that wine should always be cooled to slightly lower than the ideal serving temperature as the temperature increases by 1 to 2 as soon as it is poured into a glass Wooden racks Ss For convenient removal and addition of bottles the wooden racks can be pulled out on rails The wooden racks can also be completely removed m Pull out the empty wooden rack along with the rails as far as the stop then lift it up and out m To replace the racks set them on the extended rails so that they click into place Be sure that the ventilation slits at the rear of the unit are not blocked They are essential for the unit to operate properly 21 Storing wine Bottle display rack The display rack can only be attached to wooden racks with wide cross ties In the upper temperature zone these are found in the lower position In the lower temperature zones they are found in both the upper and lower position The display rack allows you to display selected bottles so they can be seen even with the door closed It is recommended that the wooden
20. Turning the door alarm Off Once the door is closed the alarm turns off and the alarm indicator goes out If the door has not been closed properly the alarm will sound again after five minutes alarm m To turn the alarm off early press the alarm sensor button The alarm indicator and signal will turn off Optimum temperature and air quality Wine will continue to mature depending on the surrounding conditions The length of time which wine can be kept in good condition will therefore depend not only on the temperature but also on the air quality The wine storage unit provides a constant temperature increased humidity and an odor free environment creating the best possible storage conditions for your wine Temperature Wine can be stored at temperatures between 41 F and 64 F 5 18 C If you would like to store red and white wines together choose a temperature between 50 F and 54 F 10 12 C Most white wines are palatable at this temperature It is best to take red wine out of the appliance about 2 hours before drinking Open the wine to allow it to breathe and to develop its aroma After 2 hours red wine will be at the correct temperature for drinking Storage temperatures above 72 F 22 C will cause wines to mature too quickly By contrast wine should not be stored below 41 F 5 C since it will not mature fully at this low temperature Fluctuations in temperature put wine under stre
21. ain moist Under low humidity the corks dry out from the outside and can no longer seal the bottles properly This is why wine bottles should always be stored lying down so that the wine can keep the corks moistened from within If air enters the bottle a wine will inevitably spoil Tip Wine bottles should stand upright for at least two hours before serving or better still whole day long to enable deposits to settle to the bottom of the bottle Increasing or decreasing the humidity The unit comes factory pre set to high humidity If you would like to use the wine unit for long term storage it is recommended that you select the higher humidity The interior climate will then correspond with the conditions in a wine cellar Humidity is raised or lowered for all temperature zones simultaneously be m Touch the access button so it turns yellow AS x m Tap the sensor button for any temperature zone so it turns yellow m Note the position of the V button but do not touch m Touch the access button f again so it turns white Only the access button is visible m Place one finger on the position of the V button and hold the V button will not be visible Optimum temperature and air quality m While holding down the V button press the access button J once Keep holding the V button down until the following appears in the display approx 5 seconds v L A m Tap the V button until 8
22. an be corrected without a ser vice call Repairs should only be carried out by a qualified and trained person in strict accordance with local and national safety regulations Unauthorized repairs could cause personal injury or machine damage and may void the warranty What if the appliance does not get cold Possible fault Solution The machine is not turned on Check whether the appliance is switched on at the main switch The machine is not plugged in Check that the plug is correctly inserted in the power outlet Check that the fuse has not tripped Reset the circuit breaker The temperature is set incorrectly Check the display What if the temperature is too low Select a warmer temperature See Setting the temperature The door is not closed Check that the door has been closed properly A large amount of bottles has been put in the appliance at the same time This makes the compressor run for longer causing the temperature in the appliance to fall automatically What if the compressor kicks on very frequently and for too long The ventilation slits are covered or dusty Clean with a vacuum or brush The door has been opened too frequently Once the appliance returns to the set temperature the compressor will turn off The door is not closed Check that the door has been closed properly 28 Frequently asked questi
23. anel must be 13 mm A thickness of 19 mm is recommended Custom door panels This appliance is compatible with all styles and designs of kitchen cabinetry The total weight of the decorative panel s must not exceed the following KWT 16x1 Vi 137 Ibs 62 kg Do not install a solid custom door panel onto the front of the appliance Condensation will form between the glass and custom door Installation Installation options There are many different installation options You are limited only by the design of the kitchen The door hinge cannot be exchanged Single column The appliance can be installed at any preferred location in the kitchen However be sure the door will open and close properly in the chosen location Side by side This appliance can be installed side by side with another fridge freezer using a Merging Kit The Merging Kit is available from Miele Contact Miele or your dealer for specific information about which combinations will work with your appliance For instructions on how to attach the appliances and install the heating mat please refer to the instructions included with the Merging Kit available from Miele Appliances attached together using the Merging Kit If the appliances are installed directly next to each other without a partition they need to be attached together using the Merging Kit 37 Installation Installation
24. appliance doors They will be used later in the installation niche There are transportation safety devices inside the appliance to protect the shelves until installation is complete Do not remove them or parts may be damaged m Check the appliance for damage in transit Do not install the appliance if it is visibly damaged If in doubt contact Miele 43 Installation y m Loosen the bracket that holds the appliance to the pallet N Caution The appliance is no longer secured and may be unstable m From the rear of the appliance carefully lift it from the pallet Once the appliance is on the ground it can be rolled around RemoteVision module installation optional accessory Always disconnect the appliance from the power supply when performing installation maintenance or service work Install the RemoteVision module before placing the appliance in its installation niche Once connected the RemoteVision module will increase the energy consumption of the appliance The slot for the RemoteVision module is located in the lower area of the back of your appliance 44 m Unscrew the screws on the cover 2 and pull off the sticker m Remove the cover 2 m Push the module into the slot until it locks into place m Connect the appliance to the power supply and turn it on After several seconds the indicator light will come on The indicator light will display different co
25. cted zone appears in yellow The temperature is now stored for this zone Temperature ranges upper temperature zone 3 C to 18 C or 37 F to 64 F middle temperature zone 3 C to 18 C or 37 F to 64 F lower temperature zone 8 C to 18 C or 46 C to 64 F 16 Insulation panels for thermal separation The unit has two fixed insulation panels to divide the interior into the three different temperature zones This allows you to store three different types of wine such as red wine white wine and champagne The correct serving temperature is crucial for the taste and therefore your enjoyment of the wine The following temperatures are recommended for the different types of wine Redwine 57 F to 64 F i 14 C to 18 C Ros 50 F to 54 F i 10 C to 12 C 46 F to 54 F White wine 8 C to 12 C Sparkling 45 F to 48 F wine 7 C to 9 C Chaweng 41 F to 45 F MM Le re Optimum temperature and air quality Temperature display The temperature display on the control panel always shows the desired temperature The temperature display will flash if the temperature in one of the zones is too warm or too cold Tap the V and A sensor buttons to raise lower the temperature 1 or hold them down to move through the temperature range more quickly Optimum temperature and air quality Temperature unit Fahrenheit Celsius The tempe
26. e m Clean the inside of the appliance and the accessories with a mild solution of warm water and liquid dish soap Dry with a soft cloth After installing the unit wait at least 30 minutes before switching it on During transport the fluids in the refrigeration system may have shifted and will need some time to settle Turning the appliance On Off m Open the appliance door m Turn the appliance On Off with the main switch The main switch is located on the right side underneath the control panel All three zones are switched on or off together Once on the appliance begins cooling When the door is open the interior lights come on The access button will light in the control panel The preset temperatures factory settings are reached after a few hours N Turning off the appliance with the main switch does not safely isolate it from the power supply Settings Using the settings When a sensor button has been selected with a finger touch it will appear yellow A de selected button will appear white be m Touch the access button so it turns yellow A On the control panel you will now see the sensor buttons of the three temperature zones The factory default settings for the temperature zones are as follows upper temperature zone red temper middle temperature zone white temper lower temperature zone wine storage 10 display light m To turn the d
27. ed electrician P Only connect power to the appliance when all installation work is complete IMPORTANT SAFETY INSTRUCTIONS Installation This appliance is top heavy and must be secured to prevent the possibility of tipping forward Keep the door closed until the appliance is completely installed and secured per installation instructions P This appliance must be installed and connected in compliance with the installation instructions P Installation and repair work should be performed by a Miele authorized service technician Work by unqualified persons could be dangerous and may void the warranty P Do not operate any appliance with a damaged cord or plug or if the appliance has been damaged in any manner Contact Miele s Technical Ser vice Department P This equipment is not designed for maritime use or for use in mobile installations such as recreational vehicles or aircraft P Do not install the appliance in a room with too low an ambient temperature e g a garage as this may lead to the appliance switching off for longer periods so that it cannot maintain the required temperature Use P Persons who lack physical sensory or mental abilities or experience with the machine should not use it without supervision or instruction by a responsible person P To reduce the risk of injury do not allow children to play in on or near the appliance especially in the door hinge area P
28. ine the number of screws based on the cavity width to ensure that the beam will be attached securely m Locate wall studs near the rear wall of the cavity and mark drill holes in the beam m Pre drill the wooden beam m Attach the wooden beam to the rear wall of the niche If a side by side installation is desired connect the two appliances together See the Installation Manual included with the Merging Kit Installation Sliding the appliance into the installation niche m To protect the corners of the installation space attach the supplied edge protector on both sides with adhesive tape m Plug the appliance into the power outlet The plug of the appliance should be easily accessible after installation If the plug is not accessible after the appliance has been installed disconnection from the power supply should be completed via the circuit breaker In the case of side by side installations a separate outlet must be used for each appliance m o prevent the power cord from becoming caught Tie a piece of string to the middle of the power cord and feed it forward under the appliance When sliding the appliance in pull the cable forward m Carefully slide the appliance into the space until the height adjustable wheels interlock with the anti tip brackets If resistance is felt when attempting to slide the appliance into the installation niche for example becau
29. ions Power supply 55 4 150 mm 315 16 100 mm 1 Power supply KWT 16X1 Vi 42 305 mm Door dimensions open min 90 1 6 29 mm gt KWT 16X1 Vi 26 5 3 677 mm 39 Dimensions Niche dimensions 84 2 134 mm 40 Dimensions 17 1 4 18 5 8 439 473mm 63 1623mm 10 257 mm Ev 4 102 mm 41 Installation Before you begin Read these instructions completely and carefully Have the appliance installed by a qualified technician according to the enclosed installation instructions To reduce the risk of injury or damage to the product two people should be used for installation These installation instructions are intended for use by qualified installers In addition to these instructions the appliance must be installed in accordance with all local codes In the absence of a local code the following should be used Inthe USA the National Electric Code ANSI NFPA 70 latest edition State and Municipal codes and or local codes In Canada the Canadian Electric code C22 1 latest edition Provincial and Municipal codes and or local codes 42 Tools needed for installation Cutter with adjustable blade Cordless screwdriver T 20 Torx screwdriver T 20 Hammer drill for drilling holes in wall or floor Wood drills in different sizes Hammer Open end wrench SW 13
30. isplay lighting on or off when the door is closed touch the display light sensor button SSU i m To change the settings touch the sensor button for the temperature zone you wish to set The selected sensor button appears yellow You can now select from the following settings for the selected zone s or change the pre set temperature s as desired wine white red storage temper temper For more information on setting the temperature see Optimum temperature and air quality Settings N d m To de select a temperature zone touch the sensor button for that particular zone so that it turns white or select another sensor button be m To leave the settings menu touch the access button 8 so it turns white The last settings entered are stored The sensor buttons for the three temperature zones disappear from the control panel Even if you do not touch the access button the electronics will switch back to normal after about 1 min Custom settings In the custom settings mode you can select and change functions The function possibilities are described in the respective chapters of this manual Function Display text Temperature oC m F L RemoteVision Module settings optional accessory Button sound on off Exit Custom Settings mode Humidity settings Settings Turning the button sound On Off If you prefer the buttons to be silent when
31. lation of the RemoteVision module see the Installation section of this manual 60 Be sure your wireless system meets the following requirements A wireless router that supports an IEEE 802 11b protocol Windows XP or newer operating system Mac OS X 10 3 or higher Cable or DSL modem Microsoft Internet Explorer 6 or higher Safari 2 0 or higher Firefox 1 5 or higher Please note that each wireless router manufacturer supplies their own device drivers and setup programs Due to the differences in manufacturers exact router setup instructions are not included in this manual Wording and instructions may vary RemoteVision optional accessory Accessing the RemoteVision control panel m Touch the access button so it turns yellow ASS d m Touch the sensor button for any temperature zone so it turns yellow m Note the position of the V button but do not touch m Touch the access button J again so it turns white Only the access button J is visible m Place one finger on the position of the V button and hold the V button will not be visible m While holding down the V button press the access button J once Keep holding the V button down until the following appears in the display approx 5 seconds v I Access to the Custom settings mode is now active for approximately 10 seconds m Tap the V button until appears in the display m Touch the access butt
32. lors one after the other any control light at the end indicates that the module was correctly installed Installation If the indicator light does not come on installation of the module was unsuccessful In that case repeat the process If that does not correct the problem contact Miele m Pull the antenna 9 straight out m Guide the cover 2 over the antenna and screw on the cover m Angle the antenna 9 so that it faces to the right or left m f necessary disconnect the power supply and continue installing the appliance If you would like to connect your appliance to the Home Security System proceed now see Home Security System Home Security System HSS If desired the wine storage unit can be connected to the security system of your house via a switching contact If connected you will be immediately informed of rising temperatures in the wine cooler The Home security system connection must be hooked up before the unit is installed Contact a qualified electrician or authorized agent from alarm company to connect your home s security system to the wine cellar Always disconnect the appliance from the power supply before performing installation maintenance or service work m Remove the toe kick panel from the appliance 45 Installation m Choose the desired switching contact and connect according to alarm system requirements Output of the Home Security System
33. mm Box end wrench 5 16 8 mm hex nut driver Adhesive tape Multi grip pliers Level Metal tape measure Square Other Stepladder Dolly hand tuck Wooden beam cross section min 3 x 4 75 mm x 100 mm as an alternative tilt protection length according to the width of the installation cavity Wooden screws in different sizes Optional accessories Merging Kit for side by side installation RemoteVision module for wireless installation Installation Check the installation niche To ensure a safe trouble free installation and the best possible cosmetic result check to be sure that the installation space complies with the installation requirements m Check the base see Installation m Check the dimensions of the cavity m Check that the cavity is square m Check the location of the power outlet m Check that all furniture parts in the vicinity of the appliance are securely connected to the wall m Check that the adjacent furniture fixtures do not collide with the open door Before installation N Caution the appliance is very heavy Use caution when unpacking and opening the door danger of tipping m To protect the base from damage during installation attach a hard board linoleum etc to the floor in front of the intended installation location m Take the supplied accessories out of the protective packaging m Do not remove the installation supports from the
34. niture door and glass pane m Cut the cover strips short for the top and bottom of the door to the required length Y m Push the cover strips into the gap between the furniture door and glass pane 57 Installation Mounting the air separator The air separator keeps the supply and exhaust air separate This prevents warm exhaust air from flowing into the machine optimizing the energy performance of the unit gt e e m Position the air separator in the center of the appliance door gt amp m From below screw the air separator firmly onto the door with the 2 Screws m f necessary shorten the three parts of the air separator m Insert the foam pieces back into the sides 58 Electrical connection A Avoid the risk of electrical shock Plug into a grounded 3 prong outlet Do not move the ground plug Do not use an adapter Do not use an extension cord Failure to follow these instructions can result in death fire or electrical shock Improper connection of the equipment grounding conductor may result in electric shock If you are in any doubt as to whether the appliance has been properly grounded have the appliance checked by a qualified electrician or service technician Installation repairs and other work by unqualified persons could be dangerous Before installing the appliance verify that the voltage load and ci
35. oles m lightly screw on the bracket using the pre drilled holes Attach the bracket to each attachment point with at least one screw Sad 4 m Attach the bracket at the top with at least 5 screws The bracket includes a variety of holes for the various design options of custom doors 54 When performing any work on the custom door always observe the following Always select the best load bearing surface of the custom door as the location for screws Select a screw length that is shorter than the thickness of the door front Attaching and aligning the custom door front m Fit the door handle to the custom door Note that the screws are applied from the reverse side m Open the upper door and hang the custom door with the adjusting rail over the double threaded bolts 6 m Screw the nuts 6 a few turns onto the double threaded bolts Do not tighten completely m Close the door Installation m Adjust the custom door to adjacent Attaching the covers furniture fixtures m Align the custom door with the double threaded bolts m lighten the nuts on the adjusting rail This will correct the side alignment of To mount the cover strips on both the door sides of the door click them into place from bottom to top into the K gap between the appliance door and 1 the custom door m Put the side strips 3 back into place and screw them completely down on b
36. on J to confirm See the table on the following page for a description of each setting in the display m Use the A or V buttons to select the RemoteVision options The module has been connected to the network when r appears in the display If r does not appear refer to the Network options section of the XKM 2000 Installation Instruction manual m Press and hold the access button 8 for 2 seconds to confirm the change m To return to the main menu tap the V button until a solid r appears in the display m Press the access button to confirm m Tap the V button until a c appears in the display m Touch the access button 8 You have left the Custom settings mode When you are in the Custom settings mode the door alarm is turned off automatically Once the door is closed it is reactivated 61 RemoteVision optional accessory MasterCool control panel options for RemoteVision Status indicators Description of function Flashing r Module booting phase Flashing r Not connected to network Flashing r Connection to network established no IP address assigned Solid ri Connected to network Flashing r In Ad Hoc Mode not connected Flashing r In Ad Hoc Mode connected Selectable Description of function options r Back re Reboot the module r3 Reset to factory settings rH Enter Ad Hoc Mode Note If you cannot select any option o
37. ons What if the alarm is ringing Possible fault Solution The appliance door has been open for longer than 5 minutes Close the door What if the alarm is ringing and the alarm indicator is lit The door is not closed One of these conditions has caused the The ventilation slits are covered temperature in the appliance to become too warm A large amount of wine was stored at once Once the alarm condition has been corrected the alarm will turn off and the There has been a power failure alarm indicator will stop flashing What if the display lighting is not working The display lighting turns off automatically depending on the time set See Display lighting If the display lighting still does not turn on after 15 minutes with the door closed contact Miele Technical Ser vice A white coating has formed around the wine corks The corks are made of a material which has caused a chemical reaction oxidation The white coating can be removed with a dry cloth The coating has no effect on the quality of the wine Mildew is beginning to form on the wine bottle labels Depending on the type of adhesive used mildew may begin to form on the labels Wash the wine bottles and remove any adhesive residue 29 Frequently asked questions The appliance is making noises Issue Possible fault Solution Brrrrr
38. oth sides of the appliance door Bag E contains spare screws for this purpose m Align the custom door again as needed and tighten all screws on the sides m Screw the brackets onto both sides of the appliance to hold the cover strip 55 Installation Attaching the toe kick cover The maximum height of the toe kick cover is 4 102 mm from the top of the floor Do not cover ventilation slits in the plinth Risk of damage to the appliance m If required cut the toe kick cover to the required length and height m Insert the cover strip into the space between the appliance and the side panel For side by side combinations the cover strips on both sides of the appliance are applied to the outermost spaces only m Attach the plinth to the appliance e E click i 7 da m Put the included cover plates in place m Attach the light switch cover 56 Installation m Remove the foil from the adhesive strips m Attach a toe kick cover to the plinth Attaching the cover strips If the frame width is narrow the cover strip side piece may need to be shortened To determine the required length of the side piece one test piece is enclosed with the cover strip m Cut the cover strips long for the sides of the door to the required length X m Push the cover strips on the into the gap between the fur
39. rature can be displayed in degrees Fahrenheit F or Celsius C be m Touch the access button 8 so it turns yellow SSU d m Touch the sensor button for any temperature zone so that it turns yellow m Note the position of the V button but do not touch m Touch the access button J again so it turns white Only the access button J is visible m Place one finger on the position of the V button and hold the V button will not be visible 18 m While holding down the V button press the access button J once Keep holding the V button down until the following appears in the display approx 5 seconds v L m Tap the V button until appears in the display m Touch the access button J to confirm m By touching the V button you can select either Fahrenheit or Celsius for the temperature display B Fahrenheit I Celsius return to menu m Touch the access button J to confirm the setting m Tap the V button until a c appears in the display m Touch the access button You have left the Custom settings mode When you are in the Custom settings mode the door alarm is turned off automatically Once the door is closed it is reactivated Optimum temperature and air quality Humidity In a conventional refrigerator the humidity levels are too low for storing wines High humidity levels 60 70 are very important for the storage of wine so that the corks rem
40. rcuit rating information found on the data plate match the household electrical supply If there are any questions regarding the electrical connection of this appliance to the power supply please consult a licensed electrician or call the Miele Technical Service SA 1 800 999 1360 CDN 1 800 565 6435 The appliance is supplied with a UL listed 3 wire power cord and NEMA 5 15 P plug ready for connection to a 120 V 60 Hz supply The fuse rating is 15 amps The appliance requires a 3 wire receptacle The receptacle must be installed by a licensed electrician only In the case of side by side installations a separate outlet must be used for each appliance Ideally the power outlet should be next to the appliance and easily accessible Do not connect the appliance to the power supply by an extension cord Extension cords do not guarantee the required safety of the appliance danger of overheating If any changes are needed to the household wiring or power supply this work must be performed by a qualified electrician 59 RemoteVision optional accessory Miele s RemoteVision Wi Fi technology creates a virtual link between your appliance and our monitoring center If a fault occurs Miele s client service center will be notified and contact you or another trusted individual identified on your call roster in order to gain access to your appliance to fix the problem For information on set up and instal
41. s appliance is intended for residential use only Use only as described in this Operating manual Only use the appliance for its intended purpose This appliance complies with current safety requirements Improper use of the appliance can lead to personal injury and material damage Keep these operating instructions in a safe place and pass them on to any future user Warning At an altitude of more than 8200 ft 2500 m the glass door can break Danger of injuries Electrical safety P Before installation make sure that the voltage and frequency listed on the data plate correspond with the household electrical supply This data must correspond to prevent injury and machine damage Consult a qualified electrician if in doubt P Before installation or service disconnect the power supply to the work area by unplugging the unit tripping the circuit breaker or removing the fuse P Do not use an extension cord to connect this appliance to electricity Extension cords do not guarantee the required safety of the appliance e g danger of overheating P Be certain your appliance is properly installed and grounded by a qualified technician To guarantee the electrical safety of this appliance continuity must exist between the appliance and an effective grounding System It is imperative that this basic safety requirement be met If there is any doubt have the electrical system of the house checked by a qualifi
42. s open to prevent odors Alarm The appliance is equipped with an alarm system to ensure that the temperature does not rise unnoticed because of energy loss or an open door The alarm system is always operational it does not need to be turned on Temperature alarm If the temperature becomes too warm an alarm sounds the alarm indicator turns red and flashes At the same time the affected zone flashes in the display If you use the Home Security System a temperature alarm will also trigger your security alarm Once the temperature alarm is turned off the security alarm will also shut off The alarm will sound and the display will flash if too much warm air flows into the appliance for example when bottles are being loaded re arranged or taken out alarge number of bottles are being stored for the first time the power fails 14 Turning the temperature alarm Off As soon as the alarm condition is corrected the alarm signal turns off and the affected zone stops flashing in the display The alarm indicator goes out m To turn the alarm off early press the alarm sensor button The alarm signal turns off The alarm indicator remains red and the corresponding appliance zone continues to flash until the alarm condition is corrected Door alarm If the appliance door is left open for over 5 minutes an alarm signal will sound and the alarm indicator will light up
43. se the floor is uneven m Turn the rear adjustable wheels slightly outward see Aligning the appliance then push the appliance in Be careful not to damage the power cord attached to the floor m Remove the edge protector 49 Installation Aligning the appliance m Align the appliance with the custom front 6 4 38mm me 3 4 19mm i 7 ct i 5 H i j 1 1 4 32mm The installation aids have been designed for the following total thickness of custom doors 3 4 19 mm 1 1 2 38 mm Be sure to take into account the possible differing thicknesses of the custom doors that are to be fitted subsequently The height adjustable feet at the front and rear can all be adjusted from the front Front with an open ended wrench Ye SW 13 The feet can be adjusted from the top and bottom Rear with a 5 45 8 mm hex nut driver via flexible shaft 50 A mark is located on the appliance base and is used as a standard gauge for height adjustment When adjusting the height align this mark at 1 1 4 32 mm above the floor m Place a marking out level over the installation aids on the door m Unscrew the height adjustable feet until the mark on the base has reached the indicated guide dimension 1 32 mm It is very important to comply with this dimension for the subsequent alignment of the custom door fronts
44. ss and interrupt the maturing process Therefore it is important to maintain a constant temperature Setting the temperature The factory default settings for the temperature zones are as follows The upper temperature zone is set for optimal red wine storage Red temper 62 F 17 C The middle temperature zone is set for optimal white wine storage White temper 46 F 8 C The lower temperature zone is intended for wine storage in general Wine storage 51 F 11 C You can change the purpose of the zones as you wish For example you can store white wine in the upper temperature zone as long as you adjust the temperature accordingly N m Tap the sensor button for the desired temperature zone so that it turns yellow wine white red storage temper temper m Select the preferred temperature setting so that the sensor button turns yellow The setting white temper is not available in the lower temperature zone Optimum temperature and air quality Temperatures can be independently set in all three zones The unit comes factory pre set for white wine red wine and wine storage If you wish you can change any or all of these factory settings Sew od m Select the temperature zone you would like to change the temperature in 20 Y Jae Use the V and buttons next to the temperature display to set the temperature warmer or colder The factory suggested temperature for the sele
45. subject to fines and imprisonment under provisions of environmental legislation Make sure the CFC refrigerant is removed and disposed of by a qualified technician SAVE THESE INSTRUCTIONS Guide to the wine storage unit D Circulation fans Active charcoal filter 2 Wooden racks 8 Insulation panel to separate the upper and middle temperature zones 4 Bottle display rack 8 Control panel Insulation panel to separate the middle and lower temperature zones Main switch to turn the appliance On Off Glass door with UV filter 8 Connection behind the ventilation gap for the Home Security System HSS Guide to the wine storage unit Control panel wine white red display arm i H storage temper temper light HeT Access button Long term wine storage 2 Upper temperature zone Short term storage of white wine at a Middle temperature zone a a i 8 Short term storage of red wine at a moderate temperature On Off sensor button for the display Lower temperature zone 8 Temperature display Allows you to set the temperature V colder warmer lighting and 19 Off sensor button for the temperature set the duration of the display and or door alarm lighting V shorter longer only visibly when the relevant function is activated Before use Before using for the first tim
46. ther than r Back the module has not been installed correctly 62 63 Please have the model and serial number of your appliance available before contacting Technical Service U S A Miele Inc National Headquarters 9 Independence Way Princeton NJ 08540 Phone 800 843 7231 609 419 9898 Fax 609 419 4298 www miele com Technical Service amp Support Nationwide Phone 800 999 1360 Fax 888 586 8056 TechnicalService mieleusa com Canada Miele Limited Headquarters and Showroom 161 Four Valley Drive Vaughan ON L4K 4V8 Phone 800 643 5381 905 660 9936 Fax 905 532 2290 www miele ca info miele ca general enquiries professionalQmiele ca commercial enquiries MieleCare National Service Phone 800 565 6435 905 532 2272 Fax 905 532 2292 customercareQmiele ca technical enquiries Alteration rights reserved 4209 KWT 1601 Vi KWT 1611 Vi C For the most updated manual see the Miele web site M Nr 07 682 490 02
Download Pdf Manuals
Related Search