Home

Miele G 6595 SCVi Operating and Installation Instructions

1. 39 Loading the dishwasher Griddle plate m Load the griddle plate in the bottom basket To do so fold over the front row of spikes m Arrange the griddle plate with the grilling surface facing upwards to guarantee better drying 40 Filters You can wash two range hood filters in the upper basket and two in the bottom basket at once If you only want to wash two filters put them in the upper basket 22S i a Lower basket A Be careful when unloading the filters At the end of the program the filters may still contain hot water Loading the dishwasher Cutlery 3D cutlery tray depending on model m Arrange the cutlery in the tray as shown To make unloading much easier cutlery should be grouped in zones one for knives one for forks one for spoons etc Spoon heads should be placed in con tac
2. m For larger and heavier items such as plates serving platters saucepans bowls etc Glasses cups and small items such as saucers can also be placed in the lower basket Do not place thin deli cate glassware in the lower basket m Fit the insert into the lower basket with the hooks under the long cross piece m Press down on the insert until it clicks into position m Place large platters and dishes in the center of the lower basket When tilted plates up to 13 3 4 85 cm in diameter can be accommodated 36 Loading the dishwasher Glass rack Glassware rack m The glass rack can be raised to make This rail is designed to hold glasses more room for tall items with long stems securely m Stem glassware e g wine glasses or champagne flutes can be leaned against the glass rack or suspended from it You can set the glass rack at two differ ent heights th tities X lora k ONIN DIE I i NR 1 m Lower the rail and lean tall glasses against it S VAN m Slide the glass rack to the desired height until the catches click into place at the top 37 Loading the dishwasher Hinged spikes B
3. The drying fan may continue to run for a few minutes at the end of the pro gram You can now empty the dishwasher The Optical Interface will go out 10 mi nutes after the end of the program if the door is closed A If you have deactivated the auto matic door opening function see Settings menu AutoOpen but would still like to open the door at the end of the program make sure that you open the door fully Otherwise steam from the dishwash er could damage the edge of the counter because the fan is no longer running 47 Operation Turning off At the end of a program m Open the door m The dishwasher can be switched off at any time using the button Turning the dishwasher off during a pro gram stops the program Turning the dishwasher off during the run up to a delay start time FlexiTimer will also stop the process If the dishwasher is not going to be used for a longer period of time e g while on vacation the water supply should be closed 48 Unloading the dishwasher Dishes tend to break and chip more easily when they are hot Allow the dishes to cool until they are comforta ble enough to handle before unloading them The dishes will cool much faster if you open the door when the program has ended First unload the lower basket then the upper basket and finally the cutlery tray depending on model This will prevent water drops from the upper basket and cutl
4. After confirming this with OK the prompts S Refill salt and Refill rinse aid may appear m Add salt and rinse aid if necessary see Before using for the first time Dishwasher salt and Rinse aid m Confirm the messages with OK The program selected will appear briefly in the display and the appropriate indi cator light will come on Then the display will show the estimat ed program duration for the program selected These basic settings will be saved in memory after the dishwasher has been through one complete program 21 Before using for the first time Before using the appliance for the first time you require Approx 2 qt 2 I of water Approx 2 kg 4 lbs of dishwasher salt Domestic dishwasher detergent Rinse aid formulated for domestic dishwashers If the water in your area is very soft and constantly lower than 5 gr gal 5 d you do not have to add dish washer salt The prompt to add salt will be switched off automatically Every dishwasher is tested at the fac tory There will be residual water in the appliance from this test It is not an in dication that it has been used previ ously Dishwasher salt In order to achieve good cleaning re sults the dishwasher needs to operate with soft water Hard water results in a build up of calcium deposits on dish ware and in the dishwasher Water supplies with a hardness level higher than 4 gr ga
5. Detergent A Only use detergents formulated for domestic dishwashers Refer to the manufacturer s packaging as to whether Tab products are suitable for the water hardness level in your area Please note that the cleaning and dry ing results of Tab detergents can vary greatly For optimum cleaning and drying re sults use Miele dishwasher detergent and add Miele salt and Miele rinse aid separately See Optional accesso ries Detergent dosage m Follow the dosage recommended by the manufacturer on the packaging m Unless directed otherwise use one detergent tab or add 1 1 4 2 table spoons 20 30 ml detergent to compartment Il depending on the level of soiling With very heavy soil ing you can also add a small amount of detergent to compartment I m Tabs may not dissolve completely when the Express program if availa ble is used Use only the recommended amount of detergent Continued use of too much detergent may cause machine damage A Dishwasher detergents can cause burning in the nose mouth and throat if swallowed or inhibit breathing Avoid inhaling or swallowing dish washer detergent Keep children away from detergent Keep deter gent out of the reach of children Keep children away from the dish washer when the door is open There could still be detergent residues in the dishwasher Only add detergent just before starting the program and lock the door with the child safety
6. IMPORTANT SAFETY INSTRUCTIONS This dishwasher complies with current safety requirements Inap propriate use can however lead to personal injury and damage to property To avoid the risk of accidents and damage to the dishwasher please read the installation plan and the operating instructions carefully before it is installed and used for the first time They con tain important information on its installation safety use and main tenance Keep the installation plan and the operating instructions in a safe place and pass them on to any future owner Miele cannot be held liable for damage caused by non compli ance with this information IMPORTANT SAFETY INSTRUCTIONS Correct use This dishwasher is intended for use in domestic households and similar residential environments gt This dishwasher is not suitable for outdoor use gt It must only be used as specified in these operating instructions for cleaning domestic dishware and cutlery Any other usage is not supported by the manufacturer and could be dangerous gt This appliance is not intended for use by persons including chil dren with reduced physical sensory or mental capabilities or lack of experience and knowledge IMPORTANT SAFETY INSTRUCTIONS Safety with children gt Children must be kept away from the appliance unless they are constantly supervised Children should be supervised to ensure that they do not play with the applianc
7. The intake water has not reached the required tem perature of 120 F 45 C see Water connection Water intake m Start the program again m If the fault message appears again select a differ ent program 75 Frequently Asked Questions Water drainage fault Problem Possible cause and solution The Optical Interface is flashing quickly The buzzer is sounding The following fault ap pears in the display tJ Drain Before fixing the fault m Turn the dishwasher off with the O button There is a problem with the water intake There might be water in the wash cabinet m Clean the filter system See Cleaning and care Filter system m Clean the drain pump see Frequently asked questions m Clean the non return valve see Frequently asked questions m Remove any kink or loop in the drain hose 76 Frequently Asked Questions General problems Problem Possible cause and solution The door will not open when knocked The Knock2open function has been disabled m Switch the door opening mechanism on again see Settings menu Knock2Open If the door will still not open or if there is a power fail ure the door can still be opened with the door open ing device supplied see Before using for the first time Emergency door opener The Optical Interface is flashing quickly The warning buzzer is sounding The indicator light of t
8. If the door is opened during operation all functions are automatically interrupt ed The number of knocks required for opening the door can be changed if wished see Settings Knock2Open 18 Before using for the first time Emergency door opener If the door will not open when knocked or if there is a power failure the door can be opened manually with the emer gency door opener supplied with the dishwasher m Then use it to pull the door open Closing the door m Push the baskets in m Then raise the door upwards until the catch engages m Push the emergency door opener into the gap between the dishwasher front and the neighboring unit door about 5 7 8 15 cm below the coun ter m Turn the emergency door opener clockwise until it engages behind the dishwasher front The door will then close automatically A Danger of crushing injuries Do not put your hand inside the door as it is closing 19 Before using for the first time Basic settings m Open the door m Turn the dishwasher on with the O button The welcome screen will appear when the dishwasher is turned on for the first time Language The display will change automatically to the screen for setting the language m Use the VA arrow sensors to select the language you want and also the country if appropriate and confirm your selection with OK To learn about the display read the section wit
9. lock depending on model 43 Operation Adding detergent M N po m Add the required amount of detergent m Press the opening catch on the de and close the flap tergent dispenser The flap will spring Make sure that the detergent packag open ing is properly closed after use to The flap is always open at the end of a avoid it getting damp and becoming program lumpy Dispensing aid Compartment holds a maximum of 2 teaspoons 10 ml Compartment II holds a maximum of 3 5 tablespoons 50 ml of detergent The marks in compartment II indicate the levels of approximately 1 and 2 tablespoons 20 and 30 ml respective ly The marks indicate the approximate fill level in ml when the door is open ina horizontal position 44 Operation Turning on m Turn on the water supply if it is turned off m Open the door m Make sure the spray arms are not ob structed m Press the button for at least 2 sec onds The program selected will appear briefly in the display and the appropriate indi cator light will come on Then the display will show the estimat ed program duration for the program selected Selecting a program Choose your program according to the type of load and the degree of soiling The different programs and their uses are described in the Program Over view chapter m Use the program selection button V to select the program required The indicator light of
10. salt until the reservoir is full The salt reservoir holds approx 4 lbs 2 kg of salt depending on the brand used Clean any excess salt from around the reservoir opening and then screw the cap on again firmly Immediately after filling the salt reser voir run the Express program with the Short program option selected and without any dishware in the dish washer to remove any traces of salt from the cabinet 23 Before using for the first time Salt refill indicator m Fill the salt reservoir with dishwasher salt for reactivation when S Refill salt appears in the display If it appears during a program wait until the end of the program m Confirm with OK The salt refill indicator will go out A Risk of corrosion Immediately after filling the salt res ervoir run the Express program with the Short program option selected and without any dishware in the dishwasher to remove any traces of salt from the cabinet After the salt reservoir has been filled the refill indicator may still appear in the display if the salt concentration has not yet reached the correct level If this is the case confirm again with OK The salt refill indicator will be switched off if you have programmed the dish washer for a water hardness below 5 gr gal 5 d 24 If you only ever use Tab products in your dishwasher you can switch off both refill indicators for salt and rinse aid if you wish see Settings menu
11. the next menu or another level The option which is selected will have a check V next to it To exit a sub menu use the VA arrow buttons to select the Back gt option in the display and confirm your choice with OK If you do not press any of the buttons for several seconds the display with re turn to the previous level You may need to enter your settings again Caring for the environment Disposal of packaging material The cardboard box and packaging pro tect the appliance during shipping These materials are biodegradable and recyclable Please recycle Disposal of your old appliance Old appliances may contain materials that can be recycled Please contact your local recycling authority about the possibility of recycling these materials Please be sure that your old appliance does not pose a danger to children while being stored for disposal Energy saving dishwashing This dishwasher is economical in the use of water and electricity For best re sults follow these tips For most economical dishwashing make full use of the baskets without overloading the dishwasher Choose a program that best suits the degree of soiling and the type of dishes being washed Select the ECO program depending on model for energy saving dish washing This program is the most ef ficient in terms of its combined ener gy and water consumption at clean ing normally soiled dishware If your dishwasher
12. Do not fill the rinse aid reservoir with powder or liquid detergent This will cause serious damage to the reservoir gt Inadvertently filling the salt reservoir with powder or liquid dish washer detergent will damage the water softener Make sure you have picked up the correct packet of dishwasher salt before filling the salt reservoir gt Only use special coarse grained dishwasher salt for reactivation Do not use other salts such as cooking salt agricultural grade or gritting salt These may contain insoluble additives which can impair the functioning of the water softener 12 IMPORTANT SAFETY INSTRUCTIONS gt In an appliance with a cutlery basket depending on model cut lery is cleaned and dried more efficiently if placed in the basket with the handles downwards However to avoid the risk of injury place knives and forks with the handles upwards gt Plastic items which cannot withstand being washed in hot water such as disposable plastic containers or plastic cutlery should not be cleaned in the dishwasher The high temperatures in the dish washer may cause them to melt or lose shape gt If you use the FlexiTimer Delay Start option depending on mod el make sure that the dispenser is dry before adding detergent Wipe dry if necessary Detergent will clog if poured into a damp dis penser and may not be thoroughly dispersed Please observe the information given in Technical data regard ing the capaci
13. Service 73 Frequently Asked Questions Problem Possible cause and solution The Optical Interface is flashing quickly The buzzer is sounding One of the following faults appears in the display Before fixing the fault m Turn the dishwasher off with the O button A Fault F33 The door is sometimes obstructed by an item inside the appliance m If this is the case remove the item and switch the dishwasher on again m f the same message appears again contact Miele Service A Fault F32 There may be a technical fault m Open the door manually m If the same message appears again contact Miele Service 74 Frequently Asked Questions Water intake fault Problem Possible cause and solution The Optical Interface is flashing quickly The buzzer is sounding One of the following faults appears in the display A Open water supply The water supply is turned off m Turn on the water supply all the way gt Intake Before fixing the fault m Turn the dishwasher off with the button There is a problem with the water intake m Turn on the water supply fully and start the pro gram again m Clean the water intake filter see Frequently asked questions m The water pressure at the intake is lower than 4 35 Si ee a plumber The following message appears in the display during the Energy Saver program i Intake temp low
14. Switching off the refill indicators If you switch to using detergent that does not contain salt or rinse aid it is important to remember to add dishwasher salt and rinse aid and to switch the indicators back on Before using for the first time Rinse aid Adding rinse aid Rinse aid is needed to prevent spotting on dishes and glassware The rinse aid is filled in the reservoir and the set amount will be automatically dosed A Filling the rinse aid reservoir with detergent will damage the reservoir Only pour rinse aid formulated for residential dishwashers into the res ervoir When using Tab detergents rinse aid is not needed m Press the button on the lid of the rinse aid reservoir in the direction of the arrow until the flap springs open 25 Before using for the first time m Add rinse aid only until it is visible in the opening The rinse aid reservoir holds approx 3 7 oz 110 ml m Close the flap firmly so that it clicks into place Otherwise water can enter the rinse aid reservoir during a pro gram m Wipe up any spilled rinse aid This prevents over foaming occurring dur ing the next program You can adjust the rinse aid dosage for best results see Settings menu Rinse aid 26 Rinse aid indicator When the 2 Refill rinse aid message ap pears in the display the reservoir con tains sufficient rinse aid for 2 3 pro grams on
15. be disabled in which case the door has to be fitted with a handle to open it BrilliantLight This dishwasher has interior lighting When the door is open the lighting will switch off automatically after 15 mi nutes The interior lighting can be switched off m Select the setting you want and con firm with OK 62 Optimize Standby The dishwasher is supplied with the Op timize standby function switched on as standard To save energy the dishwasher will switch off automatically a few minutes after the last time a button has been pressed or after the end of a program The dishwasher will not switch off in the event of a fault Optimize Standby can be switched off if you prefer If you do this the duration before the dishwasher switches off au tomatically increases to 6 hours Doing this will increase energy consumption m Select the setting you want and con firm with OK Settings menu Refill indicators If you consistently use a Tab detergent and the refill indicators for salt and rinse aid are bothering you you can deacti vate them if you wish m Select the setting you want and con firm with OK If you switch to using detergent that does not contain salt or rinse aid it is important to remember to add dishwasher salt and rinse aid and to switch the indicators back on Check filters You can adjust the interval at which the message to remind you to check the fil ters appears You can
16. be performed by a qualified technician in accordance with all ap plicable codes and standards Re pairs and service by unqualified per sons could be dangerous and the manufacturer cannot be held re sponsible Before connecting the appliance to the power supply make sure that the voltage and frequency listed on the data plate correspond with the household electrical supply This da ta must correspond to prevent ma chine damage Consult an electrician if in doubt GROUNDING INSTRUCTIONS THIS APPLIANCE MUST BE GROUNDED This appliance must be connected to a grounded metal permanent wiring sys tem or an equipment grounding con ductor must be run with the circuit con ductors and connected to the equip ment grounding terminal or lead on the appliance Prior to making a hardwire connec tion to the terminal remove the pow ercord Otherwise there will be a risk of electric shock from the attached plug An existing flexible supply cord or cable shall have a minimum thickness of AWG 14 120 V 60 Hz 15 A fuse rating Black wire live connect to L White wire neutral connect to N Green wire ground connect to After attaching the permanent power supply cord check that all screws on the terminal block and the strain re lief are tightened 89 Water connection Connection to the water sup ply A Water in the dishwasher must not be used as drinking water The d
17. filter m Rinse all the filters under running wa ter m Then close the flap so that the catch engages m Replace the filter system so that it lies flat in the base of the wash cabi net m Then turn the handle clockwise until both arrows point towards each oth er This will lock the filter system in place A Take care when you are fitting the filter system that it is secured in position correctly Otherwise coarse soil could get into the circulation system and cause a blockage 69 Cleaning and care Cleaning the spray arms Particles of food can get stuck in the spray arm jets and bearings The spray arms should therefore be inspected and cleaned regularly approx every 4 6 months m Turn the dishwasher off Remove the spray arms as follows m Take out the cutlery tray if your dish washer is fitted with one m Push the top spray arm upwards to engage the inner ratchet Then un screw the spray arm m Push the middle spray arm upwards to engage the ratchet Then un screw the spray arm m Remove the lower basket 70 m Pull the lower spray arm firmly up wards to remove it m Use a pointed object to push the food particles that are stuck in the spray arm jets into the spray arm m Rinse the spray arms thoroughly un der running water m Replace the spray arms and check that they rotate freely Frequently Asked Questions With the help of the following
18. has not been screwed on cor rectly m Replace it making sure that it screws back on correctly An unsuitable Tab detergent has been used m Change your detergent The water softener is programmed to too low a water hardness level m Program the water softener to a higher water hard ness level See Settings menu Water hardness There are rust stains on the cutlery The affected items are not corrosion resistant m There is no remedy Purchase cutlery which is dishwasher safe A program was not run after dishwasher salt was added Traces of salt have got into the wash cycle m Always run the Express program with the Short program option selected and without any dishware in the dishwasher after adding dishwasher salt The salt reservoir cap has not been screwed on cor rectly m Replace it making sure that it screws back on correctly 82 Frequently asked questions Cleaning the drain pump and non return valve If the water has not been pumped away at the end of a program the drain pump or the non return valve might be blocked They are however easy to clean m Turn off the dishwasher and pull the plug m Take the filter system out of the wash cabinet See Cleaning and care Cleaning the filters The drain pump is beneath the non re m Scoop the water out of the cabinet turn valve see arrow using a suitable container or utensil m Remove all foreign
19. is connected to a hot water supply select the Energy Saver program for washing a lightly to moderately soiled load Because the water is not heated in this program dishware may still be slightly damper at the end of this program than it would be with other programs Follow the detergent manufacturer s recommendations on detergent dos age When using powder or liquid deter gent you can use less detergent if baskets are only half full You can find additional tips on energy saving dishwashing in Miele s guide to dishwashing 17 Before using for the first time Opening the door A Water in the dishwasher may be This dishwasher has a motorized door hot Danger of scalding opener which is activated by knocking Only open the door during operation on the door front Knock2Open func if absolutely necessary and exercise tion extreme caution when doing so A Keep the area around the door free of obstructions At the end of programs with a drying phase see Program overview the door will open automatically a little in order to help the drying process This function can be deactivated if pre ferred see Settings menu AutoOpen m Knock twice in quick succession on the top third of the door front The door will open a little m There are two dark grips inside the door at the top Take hold of them and pull to release the door lock The door locking pin then retracts
20. no kinks in the hose and that it is not squashed or stretched After servicing the appliance ensure that the drain does not leak Venting the drain If the on site drain connection is situat ed lower than the guide path for the bottom basket rollers in the open door the drain must be vented Otherwise a siphoning effect during a program can cause the appliance to empty itself of water m To vent open the dishwasher door fully m Pull the lower spray arm firmly up wards to remove it m Cut off the top of the vent valve in the wash cabinet 91 Sound emission testing Prerequisites for sound emission tests Load the dishwasher with 16 standard place settings and use the Normal pro gram Setup for sound emission tests The dishwasher must be set up according to the following specifications o Aia D o 0 820 m Install the dishwasher into an analyzing unit m Secure the front panel 92 Sound emission testing m Push the provided fleece strips depending on model under the toe kick until it is flush with the appliance feet m Push the toe kick into place in such a way that it is flush with the door front 93 Sound emission testing m Remove the protective film from the provided insulating strip depending on model m Push the insulating strip into the front top edge of the toe kick 94 Please have the model and serial number of you
21. set an interval between 30 and 60 program cycles The Check filters message is set at the factory to appear after every 50 pro gram cycles m Select the interval you want and con firm this with OK Soak You can use this function to loosen dried on food residues in the program selected Once activated this function will be carried out with all programs until you deactivate it If you are using powder dishwasher de tergent add approx 5 g to compart ment I m Select the setting you want and con firm with OK 63 Settings menu Pre Rinse You can use this function to remove easily loosened food residues in the program selected Once activated this function will be carried out with all programs until you deactivate it m Select the setting you want and con firm with OK Brightness There are seven different display bright ness settings m Select the brightness you want and confirm this with OK 64 Volume A sequence of buzzer tones will sound at the end of the program or if there is a fault as long as the buzzer has been ac tivated Buzzer in the event of a fault The buzzer in the event of a fault will sound four times at intervals with a short pause between each set of tones The buzzer which sounds when there is a fault cannot be deactivated Buzzer at the end of a program The buzzer at the end of a program will sound four times at intervals with a short pause between each
22. set of tones The volume of the buzzer which sounds at the end of the program can be set to one of seven stages If no volume is se lected the buzzer is switched off m Select the Buzzer tone option m Use the VA arrow buttons to set the volume required and confirm your se lection with the OK button Keypad tone An buzzer tone sounds each time a but ton is pressed The volume of the keypad tone can be set to one of seven stages If no volume is selected the keypad tone is switched off m Use the VA arrow buttons to set the volume required and confirm your se lection with the OK button Settings menu Version info You can call the electronic software ver sion of your dishwasher for technical support purposes m Confirm the display with OK Showroom program For demonstration purposes only The dishwasher is fitted with various demonstration programs for showroom use Demo mode Demonstration program for show rooms Demo with sound This program activates the circulation pump to demonstrate the sound of the dishwasher Demo Drying Plus The door will open automatically BrilliantLight The interior lighting is on constantly Factory default settings You can reset all settings to the factory default settings m Select Reset and confirm with OK Closing the Settings menu You can exit the Settings menu using Close m Select Close and confirm with OK The prog
23. the holders in the bas kets Small items e g lids should there fore be placed in the cutlery tray or cutlery basket depending on model Some foods may contain natural dyes e g carrots tomatoes or to mato sauce Plastic items in the dishwasher may discolor if large quantities of these foodstuffs find their way into the dishwasher on the dishware The stability of plastic items is not affected by this discolor ation Cleaning silver cutlery in the dish washer may also cause plastic items to discolor 27 Loading the dishwasher Items not recommended for dish washing Wooden cutlery cutting boards and dishware or items with wooden parts Craft items antiques valuable vases and decorative glassware Plastic items which are not heat re sistant the high temperatures in the dishwasher may cause them to melt or lose shape Copper brass tin and aluminum items may discolor or become matt Colors painted over a glaze may fade after a number of washes Delicate glassware and glassware containing lead crystal clouding may occur over time Please note Silverware previously cleaned with a silver polish may still be damp or spot ted at the end of a program where wa ter has not run off smoothly It may need to be rubbed dry with a soft cloth Silver which has been in contact with foods containing sulphur can discolor These include egg yolk onions mayon naise mustar
24. the selected pro gram will come on Additional programs can be selected using the Additional option m Use the program selection button V to select the Additional option The first of the additional programs will appear in the display m Use the VA arrow buttons to select the program required During the course of the program you can use OK to display the name of the program which is currently running You can now select program options see Options If any program options are selected the appropriate indicator lights will also light up 45 Operation Starting a program m Start the program by closing the door within four seconds of the last press of a button The program will begin The Optical Interface comes on to show that a program has been started If you do not close the door within four seconds the indicator light of the selected program will flash and the message Press OK to start will ap pear in the display The program cannot be started until you press the OK button and close the door within four seconds A program should only be canceled in the first few minutes if at all Oth erwise important program stages could be omitted 46 Time display The estimated duration of the program selected appears in hours and minutes in the display before the program be gins During the program the time left until the end of the program is dis played Each program
25. 60 61 70 64 73 109 125 61 70 Settings menu Rinse aid You can adjust the rinse aid dosage for best results The rinse aid dosage is set in stages from 0 to 6 It is set to 3 at the factory The dosage can turn out to be higher than the set value due to the automatic adjustment of the Automatic program If spots appear on dishware and glass ware Increase the rinse aid dosage If clouding or smearing appears on dishware and glassware Decrease the rinse aid dosage m Select the setting you want and con firm your choice with OK EcoStart In order to run your dishwasher in the most economical way you can use the EcoStart option to take advantage of your electricity supplier s time variable rates see Options FlexiTimer with EcoStart With this option selected your dish washer will start automatically at your electricity supplier s cheapest rate times To use this option you must first set up to three electricity rate time zones in which the dishwasher can start You can allocate different priorities to these time zones The time with the cheapest electricity rate will be given Priority 1 Contact your electric supplier to find out the times of the cheapest electricity rates Once the electricity rate times have been set you can use the EcoStart op tion to set the latest finish time required for each program The dishwasher will then start automati cally in the chea
26. 86 siecle Operating Instructions Dishwasher To prevent accidents and machine damage read these instructions be fore installation or use en US HGO5 M Nr 10 014 190 Contents IMPORTANT SAFETY INSTRUCTIONS 00000 oo eececee eee eeeae eee eeeeaaeeeeeeeeaaeeeeeeeaas 5 Guide to the dishwasher cccccceeeeeeeeeeeeeeee cette eee eet eee aaa kaunaa adia 14 Appliance OVERVIOW keirin id a aa d aia dR 14 Control pane ksys irna a E eana aSa E EE a REET 15 DISD lay MUM CUONS E E E E ianes ie deca incest ascazaceseavdatas ia E 16 Caring for the Environment isiingie aana e AEE 17 Disposal of packaging Material eesceeeeeeenneeeeeeenaeeeeeeeaaeeeeeeenaaeeeeeeeaeeeeeeeeaas 17 Disposal of your ld APPLIANCE o eee eee ee iaeiaiai iandae ioa ai aaa Naile 17 Energy Saving dishwashing eeeceeceeeeenne eee eeeeeaeeeeeeeaaaeeeeeeeaaeeeeseenaaeeeeeeenaeeeeeeeaas 17 Before using for the first time c ccccceceeeeee eee eeeeeeeaeeaeaeeeeeeeeeeeeeeeeaaeaaeas 18 Opening the COO isieseccic ieee cece nnani EAA aiT 18 Emergency door opener oi iiivecceisnctccetcsascuceectnvececs tepeteeedanarvicad A 19 Beea ao ee E pe erect eerste eee rer reper tye cer es E EE 19 Basie SQ GS issscercci sia seecs iets seeteei bu Taedinei E ERA AA A ERA 20 Before using the appliance for the first time YOU require 0 0 eeeeeeeeeeeeeeeeeneeeeeees 22 Dishwasher saltis ransana teed teebicee rade cock TS 22 Filling the Sal
27. Change your detergent or replenish the rinse aid see Before using for the first time Rinse aid Glasses have a brown ish blue discoloration the deposit cannot be wiped off Detergent deposits m Switch to another detergent Glasses are dull and discolored the deposit cannot be wiped off The glassware is not dishwasher safe The surfaces are affected m There is no remedy Purchase glassware which is dishwasher safe Tea or lipstick stains have not been com pletely removed Plastic parts are discol ored The wash temperature of the selected program was too low m Select a program with a higher wash temperature The bleaching effect of the detergent is too low m Switch to another detergent Natural dyes e g from carrots tomatoes or ketchup may be the cause The amount of detergent used or its bleaching effect was not sufficient to deal with natural dyes m Use more detergent see Operation Detergent Discoloration is irreversible 81 Frequently Asked Questions Problem Possible cause and solution White residue is visible on dishware and cut lery clouding occurs on glassware this film can be wiped off The rinse aid dosage is too low m Increase the dosage see Settings menu Rinse aid The salt reservoir is empty m Fill the salt reservoir see Before using for the first time Dishwasher salt The salt reservoir cap
28. Questions cccceeceeeceeee eee ee eee eaaeaaeaeeeeeeeeeeeeeeeeaaeaaeas 71 o1 a a ore ogo 0 gn ouerpererree eter tees cer ee creer reeecerry a a ere errr pertrere er ertrreererr yr tree 71 Water Intake fault sscieccicececcceecedextecyisexsd cacetcendedvccuiauy chi Ea aa aaa aae Eada airaa 75 Water drainage fault eccceceseccecceeeseeeeeeeeeseeeeeeeeseeeee ees saaaeeesesaaeeseesneeaeeeeneeneneaees 76 General Probles curs reenn e a E aaa some eee 77 NOISES iskia a eee nevis tla a eee ieee ei 79 Poor Cleaning TOSUIES vii 2ecee3s iedevetiaca S 80 Frequently asked questions ccc cccceeceeeceeee eee ee eeeeeeaaeaaeaeeeeeeeeeseeeeeeaeaaes 83 Cleaning the drain pump and non return valve eee eeeeeee eects eeeeeeeeeee eee eeeeeeeeeeeeeeees 83 CUSTOINGH SEVICE 525 ccc a toes cane ey araa sauce st a ea aa a aaan aae 84 FRE DAIS sirridir arees aaan ea aeaa ae Eaa N anaE a EREET NEn 84 E AA E A E A E E ETA 84 Optional accessories cc cececeeee eee ee nettet eee ae ee eee sete eet eee a aaaeaeeeeeeeeeeeeeenes 85 lnStallation INStUUCTI OMS vsscctasececesdeesterysatanceestas tennescqectexassssacas enctseedesnarniacsaressete iets 87 Electrical COMMECUON sss sdecavececciesextieginceseavstaeceeretcetteassistieneei ciate 88 Water connection serried E etnias aA RERE 90 Connection to the Water SUPDlY riisist aia 90 BE Te e E E A E ET E T 91 SOUNC EMISSION testing sieaa na aaeei iiaia ai kanini 92
29. Y Cutlery basket Loading the dishwasher Loading for 13 standard place settings with cutlery basket JQ A it i LB LY N d ii l i Wi j sma S N _ _ Loading the dishwasher Upper basket A For safety reasons do not oper ate the dishwasher without the upper and lower baskets in place except when running the Tall items program if available A SD 7 OO Li ve 5 TA A PNA Cs TF LII SA g A ai m Use the upper basket for small light weight and delicate items such as cups saucers glasses dessert bowls etc Shallow pans or casserole dishes can also be placed in the upper basket m Long items such as soup ladles mix ing spoons and long knives should be placed lying down across the front of the upper basket Adjustable cup rack depending on model m Raise the rack to make room for tall items Glasses can be arranged along the po sitioning rail of the cup rack to give them some support during the pro gram m Lower the cup rack and lean the glasses against it or double stack smaller pieces Hinged spikes The rows of spikes can be lowered to make more room for larger items such as casserole dishes Press the yellow lever downwards 1 and then lower the spikes 33 Loading the dishwasher XXL cup rack depending on model The cup rack can be set at two d
30. a dry The Extra Dry option improves the dry ing performance in programs in which this option is available Energy consumption is increased due to an extended fan running time and an increased final rinse temperature Options FlexiTimer with EcoStart The FlexiTimer gives you three ways of starting the program by means of de laying the start You can set the start time or the finish time of a program You also have the option of taking ad vantage of time variable economy rates of electricity using the EcoStart function When using the delay start function make sure that the detergent com partment is dry before adding deter gent Wipe dry with a cloth if neces sary If the compartment is wet powder detergent can become lum py and stick to the dispenser with the result that it is not fully dis pensed Do not use liquid detergent when se lecting delay start as it can run into the dishwasher before it is required m Open the door m Switch the dishwasher on with the O button m Select the desired program m Press the button The indicator light will light up You can use the VA arrow buttons to select the Start at Finish at or EcoStart function or Back gt m Confirm selection of the function you want with OK The set time will appear and the hour number block will be highlighted You can now enter the time you want using the VA arrow buttons and con firm with OK If while you
31. ac teat a cating cabo a E E E EEE 62 ala Esa sce 5 P E E fe se anes ie dese A eavgaieaisiedistasstanciens 62 Optimize SIAN DY seriais narai a aeaa EE EAA EEAO EE EAA 62 Refill inNdiCatO Siana 63 Chock ios saosan a Wiens 63 SOAK r a E a a a T A a E a e aE 63 Pro RINSE erinmi EAA TA TARA AEA 64 BroniES Seren ana 64 MOUUMM E E E E AET 64 CE E E A E T E T T E ieanedennees 65 Showroom Dogra s ccinas cede deeeed deve ene desert ee 65 Factory Getault soling Sirus E a a Wie eeaeeeetedvces 65 Closing the Settings MenU ssssssssssseesssessrsssssssrsssinnsstnnsttnsetnnssnnsnnnnnnnnnnnnnnennt 65 Cl aning and Rot d ee neers ee eee ene er epee ere rer erase per EE ere een rr eeeer ree er art 66 Cleaning the wash Cabinet ccccccceececeeeeceeeeeneeceeeeeeseeeeeeeeneeeeeeeeeneeeeeeesesneaneeeees 66 Cleaning the door and the door seal 0 2 eeeeeeeeeeeeneeeeeeeecaeeeeeeeeaeeeeeeeeaaeeeeeeenaaeeeenee 66 Cleaning the control panel cc ceceeeeeseeeeeeeeeneeeeeeeeaaeeeeeeeaaeeeeeeeaaaeeeeeeeaaeeeeeeeeaeeeeeees 66 Cleaning the indicator reflector panel eee ceeeeee scence eeeeeeneeeeeeeeaeeeeeeeeaaeeeeeeeaaeeeenee 66 Cleaning the door front vec ivasteccciweie ce enreeee nainii AER 67 IBGE SY SUSI wisest iccthesacdicteceanidnecssteigazeahcysaizacetsaedinctsdeiaateesaiandveceseanainei ee deidiexethaavices 68 Cleaning the Spray Grins teers sivicccves ive deacons eovtitesd tinmeeven EA AEA aS 70 Contents Frequently Asked
32. and green tea scent Easy to attach to the dishwasher basket Very economical lasts for 60 wash cycles 86 Accessories Some accessories may be supplied as standard depending on model Cappuccinatore insert The Cappuccinatore insert can be used for cleaning the individual parts of the Miele Cappuccinatore in the dishwash er Cutlery basket The cutlery basket is placed in the low er basket and can be used to wash ad ditional items of cutlery Glassware rack This rail is designed to hold glasses with stems securely in the lower basket Installation Instructions Please refer to the Installation Diagram supplied with these instructions To comply with IEC sound testing protocols please contact Miele for additional instructions Information is subject to change Please refer to our website to obtain the most current product specification technical amp warranty information 87 Electrical connection Installation repairs and other work by unqualified persons could be dangerous Check that the voltage frequency and fuse rating shown on the data plate match the household mains supply The power outlet must be accessible after installation Do not use an ex tension cord to connect the dish washer to the mains Danger of over heating See data plate on the right side of the door A damaged power cord must only be replaced with a genuine Miele cord by a Miele service techn
33. ap pliance the dishwasher must only be connected to fully vented pipework A The intake hose must not be shortened or damaged in any way as it contains electrical components Water connection Drainage The machine comes equipped with a built in non return valve on the dis charge side to prevent waste water from flowing back into the dishwash er Take the drain line of the dishwasher and attach the drain line as high as possible under the counter rim of the kitchen sink before connecting the end to the drain The loop will serve to prevent a backed up drain or large volume of water in the sink from si phoning back into the dishwasher The dishwasher is supplied with ap prox 5 11 1 5 m of flexible drain hose with an internal diameter of 7 8 22 mm The drain hose can be extended us ing extensions and adapters The drainage length must not be longer than 13 1 1 2 4 m and the delivery head must not exceed 3 3 3 8 1 m If the hose is to be directly fitted to the drainage outlet on site use the hose clip supplied see installation di agram The hose can be directed to the left or the right of the appliance The on site connector for the drain hose can be adapted to different widths of hose If the connector pro trudes too far into the drain hose it will need to be shortened Otherwise the drain hose may become blocked The drain hose must not be short ened A Make sure that there are
34. are setting the time you do not press any buttons for several sec onds the display will revert to the previ ous menu You will then have to enter your settings again If you open the door for more than four seconds before the start time is reached the message Continue with OK appears in the display Press the OK button and close the door within four seconds to restart the FlexiTimer 51 Options Start at With the Start at function you set the exact time at which you want the pro gram to start m Use the VA arrow buttons to set the hour and confirm with OK The hour will be saved and the minute number block will be highlighted m Use the VA arrow sensors to set the minutes and confirm with OK The saved start time for the program selected will appear in the display The indicator light will come on m Close the door within four seconds When the set time is reached the pro gram selected will begin automatically 52 Finish at With the Finish at function you set the time at which you wish the program to end m Use the VA arrow buttons to set the hour and confirm with OK The hour will be saved and the minute number block will be highlighted m Use the VA arrow sensors to set the minutes and confirm with OK The estimated start time for the pro gram selected will appear in the display The indicator light will come on m Close the door within four seconds A message
35. d confirm with OK After confirming the Change function you can change the set time After confirming the Delete function the program duration will appear in the dis play for the selected program The indicator light will go out and the indicator light for the selected program will come on m Start the program by closing the door If you open the door for more than four seconds before the start time is reached the message Continue with OK appears in the display Press the OK button and close the door within four seconds to restart the FlexiTimer 53 Program overview Program When to use Program sequence Pre wash Main wash Interim rinse Final rinse Drying Normal Program for regular use to completely wash a full load of normally soiled dish ware with the ability to ad just energy and water con sumption based on the soil load of the dishware If re quired X If re quired X Pots amp Pans For heavily soiled dishware and normally soiled pots pans and utensils with dried on residue use 20 more detergent than rec ommended 2X China amp Crystal GlassCare program for temperature sensitive glasses and dishes with light soiling Use 50 of the detergent amount SaniWash Express To sanitize dishware e g baby bottles cutting boards and preparation dishware Quick program for lightly soiled dishware e
36. d fish and marinades A Aluminum components e g range hood grease filters must not be cleaned with a commercial or in dustrial cleaning agent These may damage the material Tip When purchasing new dishware and cutlery make sure they are dish washer safe 28 Glass care Clouding may occur on glasses after frequent washing If delicate glass ware is washed in the dishwasher ensure that only very low tempera tures are used see program chart or a special glass care program is used depending on model This will re duce the risk of clouding Purchase glassware which is dish washer safe e g Riedel glassware Use detergents with glass protective additives e g Miele CareCollection tabs Visit http www mieleglass care com international en glasscare english for more information on glass care Loading the dishwasher Loading examples Loading for 10 standard place settings with cutlery tray m m m m m n a a Upper basket Lower basket Cutlery tray depending on model 29 Loading the dishwasher Loading for 16 standard place settings with cutlery tray Cutlery tray depending on model 30 A Lower basket Loading the dishwasher Loading for 10 standard place settings with cutlery basket N AT j NN j ja aao Pe 9 DAY TT i Ly L
37. des of the dishwasher door before closing it Cleaning the control panel m The control panel should only be wiped with a damp cloth Cleaning the indicator reflector panel The indicator reflector panel for the Op tical Interface TimeControl function depending on model is situated in the cover plate underneath the counter m The indicator reflector panel should only be wiped with a damp cloth or a suitable cleaning agent designed for use on plastic Cleaning and care Cleaning the door front A If soiling remains longer it may happen that the surfaces can be come discolored or changed Remove any soiling immediately m Clean the front with a solution of warm water and a little dishwashing liquid applied with a soft sponge Wipe the surfaces dry using a soft cloth A Glass cleaners may be used to clean the exterior However do not allow them to sit or puddle this can cause damage to the surface Remove the cleaner promptly To better maintain your appliance avoid the following Cleaning products containing soda ammonia acid or chloride Descaling agents Abrasive cleaning products such as scouring powder scouring liquid or pumice stones Cleaners containing solvents Stainless steel cleaners Dishwasher cleaner Oven cleaners Glass cleaner Hard abrasive brushes or sponges e g pot scourers brushes or spong es which have been previously used with abrasive cleaning agents Eraser s
38. e Keep small children away from the appliance at all times to avoid the risk of injury There is the risk that children may lock themselves in the dishwasher gt If the automatic door opening mechanism depending on model is active keep young children away from the area in which the door opens Danger of injury in the unlikely event of a fault with the open ing mechanism gt Danger of suffocation Ensure that any plastic wrappings bags etc are disposed of safely and kept out of the reach of children gt Keep children away from detergents Dishwasher detergents can cause burning in the mouth nose and throat if swallowed or inhibit breathing Keep children away from the dishwasher when the door is open There could still be detergent residues in the cabinet Seek medical attention immediately if your child has swallowed or inhaled detergent IMPORTANT SAFETY INSTRUCTIONS Technical safety gt Installation repair and maintenance work should only be per formed by a Miele authorized service technician Work by unquali fied persons could be dangerous and may void the warranty gt Before installation check the dishwasher for visible signs of dam age Under no circumstances should you use a damaged dishwash er A damaged dishwasher could be dangerous gt The electrical safety of this appliance can only be guaranteed when continuity is complete between it and an effective grounding system It is most important that t
39. e VA arrow but tons and confirm with OK Then set the minutes and confirm with OK The time of day has now been saved 57 Settings menu Water hardness This appliance is fitted with a water softener The dishwasher must be programmed for the water hardness in your area The dishwasher must be program med for the water hardness in your area Your local water supplier can tell you the water hardness level in your area Where the water hardness fluctuates e g between 10 16 gr gal 10 15 d always program the dish washer to the higher value 16 gr gal or 15 d in this example m Select the water hardness level for your area and confirm your selection with OK A check v will appear beside the wa ter hardness which has been set d gr gal f Display 1 1 2 1 2 2 4 2 3 3 5 3 4 4 7 4 5 5 9 5 6 6 11 6 7 7 13 7 8 8 14 8 9 9 16 9 10 10 18 10 58 d gr gal of Display 11 11 20 11 12 13 22 12 13 14 23 13 14 15 25 14 15 16 27 15 16 17 29 16 17 18 31 17 18 19 32 18 19 20 34 19 20 21 36 20 21 22 38 21 22 23 40 22 23 24 41 23 24 25 43 24 25 26 45 25 26 27 47 26 27 28 49 27 28 29 50 28 29 30 52 29 30 31 54 30 31 32 56 31 32 33 58 32 33 34 59 33 34 35 61 34 35 36 63 35 36 38 65 36 37 45 39 47 66 80 37 45 46 60 48 63 82 107 46
40. ectrician if in any doubt gt Do not connect the dishwasher to the electrical supply until it has been fully installed and any adjustment has been made to the door springs gt The dishwasher may only be operated if the door opening mecha nism is working correctly Otherwise there could be a risk of danger while the automatic door opening mechanism depending on model is active To check that the door opening mechanism is working correctly The door springs must be adjusted equally on both sides They are correctly adjusted when the door remains stationary when left half open approx 45 opening angle It is also important that the door cannot fall open The door locking pins automatically retract when the door opens at the end of the drying phase gt Do not connect the appliance to the electrical supply by a multi socket adapter or an extension lead These do not guarantee the re quired safety of the appliance e g danger of overheating gt This appliance must not be installed and operated in a non sta tionary location e g on a ship gt Do not install the dishwasher in a room where there is a risk of frost Frozen hoses may burst or split The reliability of the electronic module may be impaired at temperatures below freezing point gt The water pressure flow pressure at the connection point must be between 4 35 145 psi gt A damaged appliance could be dangerous If the dishwasher gets dama
41. em in the wash cabinet is clogged m Clean the filter system See Cleaning and care Filter system The drain pump or non return valve is blocked m Clean the drain pump or the non return valve see Frequently asked questions The drain hose is kinked m Remove the kink 78 Frequently Asked Questions Noises Problem Possible cause and solution There is a knocking A spray arm is hitting the dishware noise in the wash cabi m Interrupt the program and rearrange the items net which are obstructing the spray arm There is a rattling noise Dishware is moving around in the wash cabinet in the wash cabinet m Interrupt the program and rearrange loose pieces A foreign object e g a cherry pit has become lodged in the drain pump m Remove the foreign object from the drain pump see Maintenance Cleaning the drain pump and non return valve There is a knocking This may be caused by the installation or the diame noise from the water ter of the water pipe pipe m This has no influence on dishwasher function If in doubt contact a suitably qualified plumber 79 Frequently Asked Questions Poor cleaning results Problem Possible cause and solution The dishes are not clean The dishes were not loaded correctly m See notes in Loading the dishwasher The program was not powerful enough m Select a more intensive program see Program ove
42. ery tray from fall ing onto the dishes in the lower basket Operation Interrupting a program The program will be interrupted as soon as you open the door After four seconds the indicator light of the selected program will flash and the message Continue with OK will appear in the display m Press the OK and close the door within four seconds The program will continue from the point at which it was interrupted A Water in the dishwasher may be hot Danger of scalding Only open the door if absolutely nec essary and exercise extreme caution when doing so Before closing the door again leave it ajar for approx 20 seconds This will enable the tem perature in the wash cabinet to set tle After that press the OK and close the door within four seconds Changing a program If the detergent dispenser flap has already opened do not change the program If a program has already started and you wish to change it proceed as fol lows m Open the door m Turn the dishwasher off with the button m Turn the dishwasher on again with the button m Select the desired program m Start the program by closing the door within four seconds The Optical Interface comes on to show that a program has been started 49 Options Options You can select and deselect the options using the appropriate buttons and the display m Open the door m Turn the dishwasher on with the O button The ind
43. g party dishware or to remove salt traces from the wash cabi net after refilling salt not suitable for detergent tabs 2X 54 Program overview Program When to use Program sequence Pre wash Main wash Interim rinse Final rinse Drying Pre wash Extra Quiet To rinse dishes when a complete program is not needed Extra quiet program for mixed loads with standard slightly dried on food resi due with a longer program duration Economy Water and energy saving program for standard dish ware soiling that has not dried on with a long soak ing time and a low temper ature Energy Saver Grates and filters Program for the sole use of hot water with a minimum of 45 C 120 F Wash program for cleaning Miele grates the Miele griddle plate and Miele range hood filters 2X Clean Ma chine Special cleaning program to remove grease deposits from the dishwasher 2X Consumption The consumption values refer to a hot water connection Electric power 0 01 1 5 kWh Water 1 1 7 1 gal 4 27 I 55 Settings menu Adjusting default values Opening the Settings menu m Open the door m Switch the dishwasher off with the button if it is switched on m Press and hold the OK button m Switch the dishwasher on with the button Release this button as soon as the background lighting lig
44. ged turn off the electrical supply and contact Miele IMPORTANT SAFETY INSTRUCTIONS gt The manufacturer s warranty will be invalidated if the appliance is not repaired by a Miele authorized service technician gt Defective components should be replaced by Miele original parts only Only with these parts can the manufacturer guarantee the safe ty of the appliance gt During installation maintenance and repair work the appliance must be disconnected from the electrical supply turn it off and with draw the plug from the socket gt If the connection cable is damaged it must be replaced with a special cable of the same type available from Miele by a Miele au thorized service technician only 10 IMPORTANT SAFETY INSTRUCTIONS Proper installation gt The dishwasher must be installed and connected in compliance with the installation plan gt Be careful when installing the dishwasher Wear protective gloves to avoid injury on any sharp metal components gt The dishwasher must be correctly aligned horizontally to ensure problem free operation gt In order to ensure stability built under and integrated dishwash ers must only be installed under a continuous counter which is se cured to adjacent cabinetry If you want to convert your freestanding dishwasher to a built un der U model you will need to order the appropriate conversion kit If you remove the existing toe kick you must replace it w
45. guide minor faults in the performance of the appli ance some of which may result from incorrect operation can be put right without contacting Miele Service This will save time and money The following guide may help you to find the reason for a fault and to correct it You should however note the following A Unauthorized or incorrect repairs could cause personal injury or damage to the appliance Repair work to electrical appliances must only be carried out by a suitably qualified and competent person in strict accordance with current local and na tional safety regulations The manufacturer cannot be held liable for unauthor ized work Technical problems Problem Possible cause and solution The dishwasher does The door is not properly closed not start m Raise the door upwards until the catch engages The dishwasher is not plugged in m Insert the plug The circuit breaker has tripped m Reset the fuse see data plate for the correct fuse rating The dishwasher is not switched on m Turn the dishwasher on with the O button The dishwasher stops The circuit breaker has tripped during a program m Reset the fuse see data plate for the correct fuse rating m If the circuit breaker trips again contact Miele Service After the program has The indicator reflector panel was not correctly fitted started the Optical In Refit the indicator reflector panel correctly see the terface is not v
46. h OK The change will be saved Settings menu Deleting the electricity rate times m You can delete the settings for an electricity rate time and in doing so deactivate the EcoStart option for this time zone m Use the VA arrow buttons to select the electricity rate time R1 R3 you want to delete and confirm with OK m For example select Delete R1 and confirm with OK m For example select Delete R1 and confirm with OK The settings for the electricity rate time selected will be reset m Confirm the message with OK The electricity rate time has now been deleted AutoOpen At the end of programs with a drying phase except Extra Quiet the door will open automatically a little in order to help the drying process see Program overview In the ECO program depending on mode the door will open automatically during the drying phase This function can be deactivated if wished m Select the setting you want and con firm with OK A If you have deactivated the auto matic door opening function and would like to open the door as soon as the program has finished make sure that you open the door fully Otherwise steam from the dishwash er could damage the edge of the counter because the fan is no longer running 61 Settings menu Knock2Open You can choose whether the door should open with 1 or 2 knocks m Select the setting you want and con firm with OK This function can also
47. h the same name A check v will appear next to the lan guage that has been set 20 Time of day The display will then change to the screen for setting the time The current time of day must be set be fore you can use the FlexiTimer pro gram option m Use the VA arrow buttons to set the hour and confirm with OK m Then set the minutes and confirm with OK Keeping the VA arrow buttons press ed will increase or decrease the time automatically Before using for the first time Water hardness The display changes to the water hard ness setting The dishwasher must be program med for the water hardness in your area Your local water supplier can tell you the water hardness level in your area Where the water hardness fluctuates e g between 10 16 gr gal 10 15 d always program the dishwasher to the higher value 16 gr gal or 15 d in this example It is useful to know your water hardness so that you can provide the service technician with this information in the event of any service calls Enter the water hardness below gr gal d The dishwasher is programmed at the factory for a water hardness level of 1 gr gal 1 d m Use the VA arrow buttons to select the hardness of your water supply and confirm with OK See Settings menu Water hardness for more information The message Set up successfully corm pleted will then appear in the display
48. he selected program and the message Contin ue with OK will appear in the display The dishwasher does not start or the Flexi Timer stops running The safe mode of the dishwasher was activated The following takes place If you do not close the door within four seconds of the last press of a button at program start If the door is open for longer than four seconds during a program or within the delay start time m Press the OK and close the door within four sec onds The interior lighting does not switch on when the door is opened The interior lighting has been switched off m Switch the lighting back on again see Settings menu BrilliantLight Detergent residue is left in the dispenser at the end of a program The dispenser cover Detergent residue is blocking the latch cannot be closed The dispenser was still damp when detergent was added m Make sure the dispenser is dry before adding de tergent m Remove the detergent residue The inside of the door and or the interior walls are wet after a program has finished This is caused by the drying system and does not in dicate a fault The moisture will dissipate after a while 77 Frequently Asked Questions Problem Possible cause and solution Water remains in the wash cabinet at the end of a program Before fixing the fault m Turn the dishwasher off with the O button The filter syst
49. his basic safety requirement is present and regularly tested and where there is any doubt the elec trical system in the house should be checked by a qualified electri cian Miele cannot be held liable for the consequences of an inadequate grounding system e g electric shock gt Reliable and safe operation of this dishwasher can only be assur ed if it has been connected to the electrical supply gt The dishwasher must only be plugged into the electricity supply via a Suitable switched socket using a 3 pin plug with a grounding contact it must not be hard wired The electrical socket must be easily accessible after the dishwasher is installed so that it can be disconnected from the electricity supply at any time gt There must be no electrical sockets behind the dishwasher There is a danger of overheating and fire risk if the dishwasher is pushed up against a plug gt The dishwasher must not be installed under a cooktop The high radiant temperatures which are sometimes generated by a cooktop could damage the dishwasher For the same reason it should not be installed next to open fires or other appliances which give off heat such as heaters etc IMPORTANT SAFETY INSTRUCTIONS gt To avoid the risk of damage to the dishwasher make sure that the connection data on the data plate fuse rating voltage and frequen cy matches the electrical supply before connecting the dishwasher to the mains Consult a qualified el
50. hts up in the display Keep the OK button pressed for at least 4 seconds The first option in the Settings menu will appear in the display To learn about the display read the section with the same name 56 m Use the VA arrow buttons under neath the display to select the option you want to change and confirm your selection with OK Sub menu options which have already been selected will have a check J be side them m To exit a sub menu use the VA ar row buttons to select Back gt and confirm with OK The display will revert to the menu above Settings menu Language The display can be set to appear in one of several different languages You can change the language in the display via the Language sub menu m Select the language you want as well as the country if appropriate and confirm with OK The flag after the word Language acts as a guide if a language which you do not understand has already been set If this is the case keep selecting the option which has a flag after it until you reach the Language sub menu Time of day You can select either a 24 hour or 12 hour clock The current time of day must be set be fore you can use the FlexiTimer pro gram option Setting the clock format m Select the Clock format option m Select the setting you want and con firm with OK Setting the clock m Select the Set option m Set the hour with th
51. icator light next to the program selected will come on m Select a program m Press the button for the option you want The indicator light for the relevant but ton will come on if the option is availa ble for the program selected If the option is not compatible with the program selected a message to this ef fect will appear in the display m In this instance confirm the message with OK m Start the program by closing the door The option selected will remain active for that particular program until the set ting is changed Short The Short option reduces the duration of programs in which this option is available by up to 30 In order to achieve optimum cleaning results energy consumption may in crease slightly with this option 50 When used in combination with the Rapid program the Short option results in a wash program without drying or au tomatic opening of the door if availa ble Extra economical The Extra Economical option reduces the energy consumption of programs in which this option is available by up to 20 In order to achieve optimum cleaning results the program duration is extend ed with this option Intensive lower rack The Intensive Lower Rack option inten sifies cleaning performance in the lower basket in programs in which this option is available Energy and water consumption are in creased slightly due to the extended wash duration in the lower basket Extr
52. ician Grounding instructions THIS APPLIANCE MUST BE GROUNDED In the event of a malfunction or break down grounding will reduce the risk of electric shock by providing a path of least resistance for the electrical cur rent This appliance is equipped with a cord having an equipment grounding conductor and a grounding plug The plug must be plugged into an appropri ate outlet that is installed and grounded in accordance with all local codes and ordinances 88 Improper connection of the equip ment grounding conductor can result in electric shock Do not modify the plug provided with the appliance if it will not fit the out let have a proper outlet installed by a qualified electrician If there is any question concerning the proper electrical connection or grounding of this appliance to the powersupply please consult a li censed electrician or call Miele s Technical Service Department USA 1 800 999 1360 CDN 1 800 565 6435 Specifications The dishwasher comes equipped with a 4 ft 1 2 m powercord with a molded plug for connection to 120 V 60 Hz 15 A grounded receptacle Electrical connection Hardwired electrical connection It is possible to hardwire this appliance to an existing power cable CAUTION Before servicing discon nect the power supply by either re moving the fuse shutting off the power main or manually tripping the circuit breaker Installation work and repairs should only
53. iele parts On ly genuine Miele parts installed by fac tory trained professionals can guaran tee the safety reliability and longevity of your Miele appliance Please note that unless expressly ap proved in writing by Miele s Service de partment Extended Service Contracts offered by other providers for Miele products will not be recognized by Miele Our goal is to prevent unauthor ized and untrained service personnel from working on your Miele products possibly doing further damage to them you and or your home To learn more about MieleCare Extend ed Service Contracts please contact your appliance dealer or visit us online at http www mieleusa com Optional accessories Dishwasher detergent and rinse aid as well as cleaning and care products are available as optional accessories All the products are designed for use with Miele dishwashers These and many other useful products can be ordered via the Miele website or from Miele see end of this manual for contact details Dishwasher detergent rinse aid and salt When you decided to buy a Miele dish washer you chose excellent quality and performance However ensuring that your dishwasher always delivers the best possible results will also depend on your choice of dishwasher deter gent rinse aid and dishwasher salt as cleaning results can vary depending on the brand used With Miele CareCollection products you can be sure of optimum result
54. ifferent widths so that it can also accommodate large cups m Pull the cup rack upwards and click it back into position at the required width Glassware rack This rail is designed to hold glasses with long stems securely mm pS ies i ZIRI 7 y J TE d ih TAS m Lower the rail and lean tall glasses against it 34 m You can also move one of the side in serts of the cutlery tray to make more room for tall glasses Adjusting the height You can set the glassware rack at two different heights m Pull the rail upwards and click it back into position at the required height Use the low setting for small glasses and tumblers Use the high setting for tall glasses and glasses with stems Loading the dishwasher Adjusting the upper basket In order to gain more space for taller items the upper basket can be adjusted on three levels with 3 4 2 cm be tween each level The upper basket can also be set at an angle with one side high and the other side low Make sure however that the basket can slide smoothly in and out of the cabinet m Pull the upper basket out To raise the upper basket m Lift the basket until it clicks into place To lower the upper basket m Pull upwards on the levers at either side of the upper basket m Adjust the basket to the desired height and then push the levers se curely back down int
55. ina a aaa En A EAA E EEA REE 45 Starting a Progra eesriie ina iinan NE ANENE AANREKENEN 46 Time dipl eces a 46 Energy management s s rsndnsnrsensan dinaan nan nnan EENEN AN aaan Aana Ran aaa TARR ninna TEAS 47 2 Contents At thG end Of the progra c2 5 d deceeei decedaaceseakceiestsdeccaneeshenedinsdsenedingsseaeainecesdeiadece 47 TUPMUING OM eieaa aa svasecasveds EA cress ied cannes sedi EE RA 48 Unloading the dishwasher iiciiectscetssiecedesedueccevensasectetesssecceteseyaextees va eerseesiieceetesensies 48 Interrupting a progran ooo eee eeceeeeeeeenne eee eeee nae Enina an NAAR ANANN ARANE EDORA NENNE ENANAR 49 Changing a Progr ali assisia snskoasiirada anA Ea ARRA EEA ESE 49 OPUONS aiti a E A a a e eaaa Aa EE 50 COPE OM Soinissa a a a a oaa aaan a aa E a 50 FlexiTimer with ECOStart 0 2 cceeeeeseeeeeeenneeeeeeeaaeeeeeeeaaaeeeeeeeaaeeeeseseaaeeeeseeaaaeeeeeeeaas 51 Program OVEIrVieW 2 ccccccecee cette ee eeeeeee aaa aeae cette teeta ea aaeeaaaaaeaeeeeeeeeeeeeeeeeeaeaaeas 54 S ttinNgS MENU reann ee eee eee cer torr eetee e e RE 56 Opening the Settings MeN ccecceeeeeeeeceeeeeeeeeceeeeeeeeeeeeeeeeeeeeeeesneeeeeeseeeeeeeeenes 56 Language ree e iea e e a a EE A 57 TMO O QA iria aa AAA A AEE E AEA AAE EE A 57 Water NardneSs wicresescciieseieretisleer een seared AREAREN EANNA 58 Rinse didesa a datas 59 ECON ea a eea a Deca E Aa a E a a cance 59 AUtOOP en aiaa Mini Ahead eee 61 KMOCK2 Oe Mxaasedes cava ccgdes S
56. ishwasher may be connected to a cold or hot water supply up to a maximum of 140 F 60 C We would only recommend connec tion to a hot water supply if it is eco nomical e g a solar powered supply When connected to a hot water sup ply all program stages which would otherwise be carried out with cold water will be carried out with hot wa ter The Energy Saver program if availa ble requires a hot water supply be tween 115 F 45 C minimum and 140 F 60 C maximum The higher the water intake tempera ture the better the cleaning and dry ing results The intake hose is approx 4 11 1 5 m long A 1 5 m long flexible met al extension hose pressure tested to 2 030 psi is available as an optional accessory if required A faucet with a 3 8 male thread must be provided on site This appliance is constructed to comply with ANSI ASSE 1001 IEC EN DIN 61770 VDE 0700 Part 600 and may be connected to a suit able supply without an extra non re turn valve if national regulations per mit 90 Water pressure Must be between 4 5 145 psi 0 3 10 bar If the wa ter pressure is lower than this the fault message Intake will appear in the display see Frequently asked questions If the water pressure is too high a pressure reducer valve must be fitted After connecting the dishwasher to the water supply check that the wa ter intake is airtight A To avoid any damage to the
57. isible installation plan 71 Frequently Asked Questions Problem Possible cause and solution The door locking pins do not retract after the door has opened auto matically There is a fault with the door mechanism or the door has not been correctly balanced m Contact Miele Service The AutoOpen function must be switched off be fore the dishwasher is used again see Settings AutoOpen Danger of injury in the unlikely event of another fault 72 Frequently Asked Questions Problem Possible cause and solution The Optical Interface is flashing quickly The buzzer is sounding One of the following faults appears in the display Before fixing the fault m Turn the dishwasher off with the O button A Fault FXX There may be a technical fault After a few seconds m Turn the dishwasher back on m Select the desired program m Close the door If the error message is displayed again there is a technical fault m Contact Miele Service tJ Waterproof The WaterProof System has reacted m Turn off the water supply m Contact Miele Service A Fault F78 A fault has occurred in the circulation pump m Turn the dishwasher off for at least 30 seconds with the button m Turn the dishwasher back on m Select the desired program m Close the door If the error message is displayed again there is a technical fault mg Contact Miele
58. ith a U model plinth This is necessary to avoid the risk of injury caused by protruding metal parts gt The door springs must be adjusted equally on both sides They are correctly adjusted when the door remains stationary when left half open approx 45 opening angle It is also important that the door cannot fall open The appliance may only be used with correctly adjusted door springs IMPORTANT SAFETY INSTRUCTIONS Proper use gt Do not use solvents in the dishwasher Danger of explosion gt Do not inhale or ingest powder detergent Dishwasher detergents contain irritant or corrosive ingredients which can cause burning in the nose mouth and throat if swallowed or inhibit breathing Seek medical attention immediately if detergent has been swallowed or in haled gt Avoid leaving the door open unnecessarily as someone could trip over it and be injured by it gt Do not sit or lean on the opened door This could cause the dish washer to tip and be damaged and you could get injured gt Dishes can be very hot at the end of a program Allow them to cool until they are comfortable enough to handle before unloading Only use detergent and rinse aid formulated for domestic dish washers Do not use dishwashing liquid gt Do not use commercial or industrial detergents as these may cause damage and there is a risk of a severe explosive chemical re action Such as an explosive oxyhydrogen gas reaction gt
59. l 4 d needs to be softened This takes place automatical ly in the integrated water softener The water softener in the dishwasher is suit able for a water hardness level of up to 73 gr gal 70 d The water softener requires dishwasher salt Depending on the water hardness level lt 22 gr gal or 21 d dishwasher salt is not required if combination tablets are being used see Operation Deter gent 22 A Dishwasher detergent will de stroy the water softener Do not fill the salt container with dishwasher detergent even liquid detergent A Use only special coarse grained dishwasher salt or other pure kitchen salt Other types of salt may contain in soluble components which can dam age the water softener Before using for the first time Filling the salt reservoir Important Before filling the salt res ervoir with dishwasher salt for the first time you must fill it with approx 2 qt 2 I of water to enable the salt to dissolve Once the dishwasher has been used for the first time there is always suf ficient water in the reservoir m Remove the lower basket and un screw the salt reservoir cap Water will run out of the reservoir when the cap is removed It should therefore only be removed in order to refill the salt reservoir m Fill the reservoir with approx 2 qt 2 of water first use only Place the funnel provided over the salt reservoir and carefully fill with
60. ly m Add rinse aid m Confirm with OK The rinse aid refill indicator will go out If you only ever use Tab products in your dishwasher you can turn off both refill indicators for salt and rinse aid if you wish see Settings menu Turn ing off the refill indicators Loading the dishwasher Tips Remove coarse food residues from the dishware There is no need to rinse items under running water A Do not wash items soiled with ash sand wax grease or paint in the dishwasher These will damage the dishwasher Dishware can be loaded anywhere in the baskets but the following notes should be observed Do not place dishes or cutlery inside other pieces They will cover each other Load the dishware so that water can access all surfaces This ensures that they get properly cleaned Make sure that all items are securely positioned Hollow items such as cups glasses pans etc must be inverted in the basket Tall narrow hollow items e g champagne glasses should be placed in the center of the basket to ensure better water coverage Concave items such as mugs or bowls should be placed at an angle so that the water can run off The spray arms must not be blocked by items which are too tall or hang through the baskets If in doubt test for free movement by manually rotat ing the spray arms Make sure that small items cannot fall through
61. n button V Arrow buttons V A On Off Button oe FlexiTimer with indicator ight These operating instructions apply to several different dishwasher models with different heights The specific dishwasher models are referred to as follows Standard 31 11 16 80 5 cm high dishwashers integrated and 33 1 4 84 5 cm high dishwashers freestanding XXL 33 1 4 84 5 cm high dishwashers integrated 15 Guide to the dishwasher Display functions General information The display is used to select or set the following The program The FlexiTimer Delay Start The Settings menu The display can show the following The program stage The estimated time left for the pro gram to run Any relevant fault messages and in formation To save energy the dishwasher switches off after a few minutes if you do not press any buttons during this time To switch the dishwasher back on again press the button 16 Settings menu The Settings menu is used to adapt the electronic module of the dishwasher to changing requirements See the Set tings menu chapter for more informa tion on accessing the settings menu The arrows in the display indicate addi tional options You can use the V A ar row buttons next to the display as ap propriate to select these additional op tions The OK button is used to confirm a message or setting and also to move to
62. o position Depending on the setting of the upper basket the following plate dimensions can be accommodated Dishwashers with cutlery basket see data plate for model number Upper Plate in inches cm pasket Upper basket Lower arua basket ment Stand XXL ard Upper 77 8 97 16 123 16 20 24 31 13 3 4 35 Middle 8 10 1 4 11 7 16 11 16 26 29 22 Lower 9 7 16 11 28 10 5 8 24 27 Dishwashers with cutlery tray see data plate for model number Upper Plate in inches cm Basket Upper basket Lower adjust basket ment Stand XXL ard Upper 77 8 71 2 123 16 15 19 31 13 3 4 35 Middle 6 81 4 117 16 11 16 21 29 17 Lower 71 2 91 16 10 5 8 19 23 27 When tilted plates of up to 13 3 4 35 cm can be accommodated see Lower bas ket Depending on the setting of the upper basket a variety of plate dimensions can be accommodated 35 Loading the dishwasher Lower basket Removable MultiComfort insert The rear section of the lower basket is used for washing cups glasses plates pots and pans You can remove the MultiComfort insert to make more room for larger items such as casserole dishes Removing the insert m Pull the yellow handle forwards and remove the insert Refitting the insert
63. objects from the drain pump glass or bone splinters Before returning the non return valve check that the drain pump is not blocked Spin the propeller sever al times in both directions to check for obstructions m Carefully reinsert the non return valve and secure it with the locking clamp A Make sure the locking clamp clicks into place A Be careful not to damage any delicate components when cleaning the drain pump and the non return m Lift the non return valve up and out valve 2 and rinse well under running water m Press the catch for the non return valve inwards m Remove all foreign objects from the non return valve 83 Customer service Repairs For problems that you cannot resolve on your own please contact your Miele dealer or Miele Service The telephone number for Miele is listed at the back of these instruc tions In the event of a fault which you cannot correct yourself please contact the Miele Service Department at the phone number on the back of this booklet 84 Warranty For more information please refer to the included warranty MieleCare USA only MieleCare our Extended Service Con tract program gives you the assurance of knowing that your appliance invest ment is covered by 5 years of worry free ownership MieleCare is the only Extended Service Contract in the industry that guarantees repairs by a Miele Authorized Service Provider using genuine M
64. ottle holder The spikes at the front are used for The bottle holder can be used to wash washing plates soup bowls platters narrow items e g milk and baby bot dessert bowls and saucers tles The spikes can be lowered to make more room for large items e g pots pans and dishes U U m If the bottle holder is not needed lift it up and fold the sides down as illustrated m Press the yellow lever downwards Q and then lower the spikes 38 Loading the dishwasher Grates and filters You can also wash Miele grates the Miele griddle plate and Miele range hood filters m Select the Grates amp Filters program for optimum dishwashing results A Protruding parts can damage the dishwasher Load the dishwasher in such a way that no corners protrude over the side of the basket A Heavy and sharp wash loads can damage the coating of the basket struts Load grates griddle plates and fil ters carefully A Only place dishwasher safe Miele grates filters and gill plates in the dishwasher Grates A Rust damages the dishwasher Wash only grates that are undam aged and not rusty m Place the upper basket in the top po sition m Load the grate in the bottom basket To do so remove the MultiComfort insert and fold over the front row of spikes
65. pest electricity rate time and the program will end at the lat est at the finish time set 59 Settings menu Setting the electricity rate times Before you can use the EcoStart option you must set at least one electricity rate time m Use the VA arrow buttons to select the electricity rate time R1 R3 you want to set and confirm with OK The start of the electricity rate time se lected will appear in the display and the hour number block will be highlighted m Use the VA arrow buttons to set the hours and minutes for the start time and confirm both with OK The end of the electricity rate time se lected will appear in the display and the hours number block will be highlighted m Use the VA arrow buttons to set the hours and minutes for the end time and confirm both with OK The electricity rate time will be saved and its priority will appear in the dis play m Use the VA arrow buttons to set the priority you want and confirm with OK m Confirm the message with OK The electricity rate time will be activat ed 60 Changing the electricity rate times You can change the start finish or pri ority of an electricity rate time m Use the VA arrow buttons to select the electricity rate time R1 R3 you want to change and confirm with OK m Select the setting you want to change and confirm with OK m Use the VA arrow buttons to change the setting and confirm with OK m Confirm the message wit
66. ponges Sharp metal scrapers Steel wool Steam cleaning appliances 67 Cleaning and care Filter system The filter system in the base of the wash cabinet prevents food from being redeposited on dishes It also protects the circulation pump from damage caused by foreign objects A This dishwasher must not be used without all the filters in place Collection of coarse soil may cause the filters to clog The level of soiling and time it takes before the filters need cleaning will vary depending on use The message Check filters will appear in the display after every 50 program cy cles factory default setting You can set the interval for the Check filters message to appear to a value between 30 and 60 program cycles see Settings menu Check filters m Check the filter system m Clean it if necessary m Then confirm the message with OK The message will go out 68 Filter system m Turn the dishwasher off m Turn the handle counter clockwise to release the filter system m Lift the filter system out of the dish washer 2 Remove any coarse parti cles and rinse the filter well under running water Use a nylon brush if necessary A Ensure that course soil does not get into the circulation system and cause a blockage Cleaning and care To clean the inside of the filter the flap must be opened m Press catches together in the di rection of the arrows as shown and open the
67. r appliance available before contacting Technical Service U S A Miele Inc National Headquarters 9 Independence Way Princeton NJ 08540 Phone 800 843 7231 609 419 9898 Fax 609 419 4298 www mieleusa com Technical Service amp Support Nationwide Phone 800 999 1360 Fax 888 586 8056 TechnicalService mieleusa com Miele www miele shop com Miele Canada Importer Miele Limited Headquarters and Miele Centre 161 Four Valley Drive Vaughan ON L4K 4V8 www miele ca Customer Care Centre Phone 800 565 6435 905 532 2272 customercare miele ca Germany Manufacturer Miele amp Cie KG Carl Miele StraBe 29 33332 G tersloh G 6590 G 6595 C en US M Nr 10 014 190 04
68. ram selected will appear in the display briefly and the indicator light for the program selected will come on 65 Cleaning and care Check and clean your dishwasher regularly This will help avoid prob lems and faults A All surfaces are susceptible to scratching Contact with unsuitable cleaning agents can alter or discolor all surfa ces Cleaning the wash cabinet Generally the wash cabinet is self cleaning if the correct amount of deter gent is used If however there are lime scale or grease deposits in the cabinet these can be removed with a special dish washer cleaner see Optional accesso ries Follow the instructions on the packaging If you mainly use low temperature pro grams lt 120 F 50 C there is a risk of bacteria and unpleasant odors building up in the wash cabinet To prevent this happening the dishwasher will automat ically increase the temperature in the fi nal rinse of the selected program after several programs using low tempera tures have been run m Clean the filters in the wash cabinet regularly 66 Cleaning the door and the door seal Bacteria could build up on the door seal and the sides of the dishwasher door as these surfaces are outside the wash cabinet and are not accessed and cleaned by the spray arm jets m Wipe the door seals regularly with a damp cloth to remove food deposits m Wipe off any food or drink residues which may have dripped onto the si
69. rview Not enough detergent was dispensed m Use more detergent or change your detergent Items are blocking the path of the spray arms m Rearrange the items so that the spray arms can rotate freely The filter system in the base of the wash cabinet is not clean or is not correctly fitted This may cause the spray arm jets to get blocked m Clean and or fit the filter system correctly m Clean the spray arm jets if necessary see Clean ing and care Cleaning the spray arms The non return valve is open and blocked Dirty water has flowed back into the wash cabinet m Clean the drain pump and the non return valve see Frequently asked questions Smearing appears on glassware and cutlery There is a bluish sheen on the surface of glass ware film can be wiped off The rinse aid dosage is set too high m Reduce the dosage see Settings menu Rinse aid 80 Frequently Asked Questions Problem Possible cause and solution Dishware is not dry or cutlery and glasses are spotty The rinse aid dosage is set too low or the rinse aid reservoir is empty m Replenish the reservoir increase the dosage or change the brand of rinse aid see Before using for the first time Rinse aid Dishware was taken out of the cabinet too soon m Leave it in for longer see Operation Combination tabs have been used which have im paired drying performance m
70. s as these products have been specially de signed for Miele dishwashers Detergent tabs Sparkling results even with stubborn food deposits Combination product with other components such as rinse aid salt and glass protection additives Phosphate free safe for the envi ronment Water soluble wrapping no need to unwrap Powder detergent With active oxygen for thorough cleaning With enzymes which are effective even in low temperature programs With glass protection against corro sion Rinse aid For gleaming glasses Helps dishware to dry With glass protection against corro sion Specially designed cap for precise easy dispensing Dishwasher salt Prevents lime scale on dishware and in the appliance Extra coarse grained 85 Optional accessories Dishwasher care products Miele cleaning and care products pro vide optimum care for your dishwasher Dishwasher cleaner Cleans the dishwasher effectively and thoroughly Removes grease bacteria and un pleasant odors Ensures excellent dishwashing re sults Dishwasher descaler Removes heavy lime scale deposits Mild and gentle with natural citric acid Dishwasher conditioner Removes odors lime scale and light deposits Maintains the elasticity and leak tightness of the seals Dishwasher freshener Neutralizes unpleasant odors Fresh pleasant lime
71. stage is indicated by a symbol fy Pre wash Soak IN Main wash SA Interim rinse Final rinse SS Drying Finish The program duration displayed may vary with the same program It is influ enced by among other things the wa ter temperature at each intake the re activation process the type of deter gent the amount of dishware and the amount of soiling When a program is selected for the first time the display shows an average time for a cold water intake The times shown in the program over view refer to standard test loads and temperatures Each time a program is run the elec tronic module calculates the program duration required according to the tem perature of the water taken into the dishwasher and the amount of dish ware Operation Energy management To save energy the dishwasher will switch off automatically 10 minutes af ter the last time a button has been pressed or after the end of the program see Settings menu Optimize stand by m Press the button to switch the dishwasher back on The dishwasher will not switch off while a program or the FlexiTimer is running or if there is a fault At the end of the program At the end of a program the Optical In terface will be visible flashing slowly with the door shut The buzzer might al so be sounding The program has finished when End appears in the display and the door has opened slightly if applicable
72. t reSOrVoil ec eeceeeeeneeeeeeenceeeeeeeeae eee eeeeaaeeeeeeeaaaeeeeeeeaaeeeeeeeaaeeeeeee 23 etc lt 1 Male lore 1 0 Reerneent ter cenncecnerrr E etree rr epee trerer ere ers 24 Rinse Aidra cc cceccecccueey cnadncawadcdscevyveadeanea ecacdauea vanes toa E cdee EE avcoatande 25 Adding WINS AIG seess sirana aN Ean r ESSA AE EiS NAARAS a AADA 25 Rinssaid indicato sscan terrae a a i EE 26 Loading the dishwaShe l 0scicccsccccesseesiscccessetcceeeecneaceeesssaasseaecaseidacesseaaceaneeanensces 27 TIDS siedeceies Sastvanen haere qc odidderuveccnecie cad a EEE EEEE aa E N EE NEEE EEEREN 27 Loading SXaIMPlOS cscs cgscceseeedtteces dvds es isenana raaa is Seda daced tein szacedeavdatesidsiantazsdaaeaece 29 Upper DasSkKet ikenien ir rrererr errr cent ere rerrepteree rece tener rrererereceerr errr trey 33 Adjusting the upper Dasket c ceceeeeeeeeeeeeeeeceaeaeceeeeeeeeeeeeteeeaaaaeaeeeeeeeeees 35 Lower basket cirrose ai a eiaa a aE adad aaa aaa ENa 36 Grates And filters a ae a aae a AE a Aa 39 N a A E E E E I E ter E teers 41 3D cutlery tray depending on model sessseesssesssessssssssissssrssrnnesrnessnnesinnsnnns 41 Cutlery basket depending on MOdel ccceeesceeeeseeeeeeeesseeeeeeeesseeeeeeeeeseeaeees 42 OPS ALON sis ae aka e e ea a a ra n EE s AA SEE RAN SEa OEE 43 DOTS A A T E A T A A A E E 43 Adding detergant esssrreniisssiiniriidadas iiaiai AERAN AEAEE 44 Eat sO nE I T T E T 45 DEISCIING A Progra ass
73. t with at least one of the serrated re tainers on the base of the cutlery tray to ensure that water runs off them freely The upper spray arm must not be blocked by items which are too big The side sections of the tray can be moved into the middle to accommodate tall items of dishware in the upper bas ket SS If spoon handles do not fit between the holders lay them the other way round Ti m You can use the yellow slide to adjust the height of the middle section of the cutlery tray to make more room for large items of cutlery such as serving spoons and ladles 41 Loading the dishwasher Cutlery basket depending on model The cutlery basket can be placed any quired where on the front rows of spikes in the lower basket m To avoid the risk of injury knives and forks should be placed with the han dles upwards in the basket However cutlery placed handle down in the basket will come out cleaner and dri er m Place small items of cutlery in the in dividual slots on three sides of the cutlery basket Cutlery insert for the cutlery basket Use the insert supplied for heavily m Insert cutlery with the handles facing soiled items of cutlery The insert sepa downwards rates the items so that they can be m Distribute them evenly along the in more easily accessed by water sert 42 Operation
74. ty of the dishwasher Accessories gt Use only genuine original Miele parts If spare parts or accesso ries from other manufacturers are used the warranty may become invalid Disposal of your old dishwasher gt Make the door lock inoperative so that children cannot acciden tally shut themselves in Remove or destroy the locking bracket of the door lock and make appropriate arrangements for the disposal of the appliance SAVE THESE INSTRUCTIONS AND PASS THEM ON TO ANY FUTURE USER Guide to the dishwasher Appliance overview O Upper spray arm not visible 2 Cutlery tray depending on model 3 Upper basket Middle spray arm Air intake for drying depending on model Lower spray arm 14 Filter system Data plate Rinse aid reservoir Dual compartment detergent dis penser Optical Interface 2 Reservoir for dishwasher salt Guide to the dishwasher Control panel Normal SaniWash Short C EL amp Extra Economical wie GG Pots amp Pans Express r Miele QD china amp crystal Additional DYE intensive Lower Rack gt Extra D K Optical Interface OK button 2 Program selection Display 3 Option buttons with indicator lights Program selectio
75. will appear in the display if the program cannot be completed by the set finish time because it has too long a running time The program will start automatically when the estimated start time is reached Options EcoStart The EcoStart function allows you to take advantage of time variable economy rates of electricity Before you can use this option you must set up to three electricity rate time zones See Settings menu EcoStart You then set the latest time at which the program selected should end The dishwasher will start automatically in the cheapest rate zone within the time set m Use the VA arrow buttons to set the hour and confirm with OK The hour will be saved and the minute number block will be highlighted m Use the VA arrow sensors to set the minutes and confirm with OK The estimated start time for the pro gram selected will appear in the display The indicator light will come on m Close the door within four seconds The selected program will start auto matically during the most cost effective time zone It will finish at the latest by the set finish time Changing or deleting set times You can change the set times or the program before the start time in the dis play is reached m Open the door m Press the button m Use the VA arrow buttons to select the setting you want to change and confirm with OK m Use the VA arrow buttons to select the Change or Delete function an

Miele G 6595 SCVi Operating and Installation Instructions

Contents

Download Pdf Manuals

Related Search

Related Contents