Miele G 4700 SCi CLST Futura Dimension Slimline Operating and Installation Instructions
Contents
1. 0 D Upper spray arm not visible 2 Cutlery tray depending on model 3 Upper basket Middle spray arm Air intake for drying depending on model Lower spray arm 14 Filter system Data plate Rinse aid reservoir Dual compartment detergent dis penser Reservoir for dishwasher salt Guide to the dishwasher Control panel Normal e SaniWash Pots amp Pans e Express China amp Crystal e Rinse amp Hold lt Intake Drain Rinse Aid Salt kN G L Program selection 2 Time display Check Refill indicators Start button with indicator light Short button with indicator light Delay Start button with indicator light Program selection button V On Off Button 15 Caring for the environment Disposal of packaging material The cardboard box and packaging pro tect the appliance during shipping These materials are biodegradable and recyclable Please recycle Disposal of your old appliance Old appliances may contain materials that can be recycled Please contact your local recycling authority about the possibility of recycling these materials Please be sure that your old appliance does not pose a danger to children while being stored for disposal 16 Energy2. m For larger and heavier items such as plates serving platters saucepans bowls etc Glasses cups and small items such as saucers can also be placed in the lower basket Do not place thin deli cate glassware in the lower basket Hinged spikes Both rows of spikes at the front can be lowered to make more room for large items e g pots pans and dishes m Press the yellow lever downwards and then lower the spikes 31 Loading the dishwasher Comfort insert The comfort insert is used for cups glasses plates dishes and pots The comfort insert can be removed to make more room for larger items such as casserole dishes m The cup rack can be raised to make more room for tall items m Stemware e g wine glasses or champagne flutes can be leaned against the cup rest or suspended from it 32 Removing the insert m Press the insert downwards and press the catch inwards at the same time Refitting the insert m Position the comfort insert at the back of the lower basket m Fit the insert into the lower basket with the hooks under the long cross piece m Push the insert downwards and at the same time move the catch out wards until it clicks into position Loading the dishwasher Bottle holder depending on model The bottle holder can be used to wash narrow items e g
3. If the hose is to be directly fitted to the drainage outlet on site use the hose clip supplied see installation di agram The hose can be directed to the left or the right of the appliance The on site connector for the drain hose can be adapted to different widths of hose If the connector pro trudes too far into the drain hose it will need to be shortened Otherwise the drain hose may become blocked The drain hose must not be short ened 70 A Make sure that there are no kinks in the hose and that it is not squashed or stretched After servicing the appliance ensure that the drain does not leak Venting the drain If the on site drain connection is situat ed lower than the guide path for the bottom basket rollers in the open door the drain must be vented Otherwise a siphoning effect during a program can cause the appliance to empty itself of water m To vent open the dishwasher door fully m Pull the lower spray arm firmly up wards to remove it m Cut off the top of the vent valve in the wash cabinet Sound emission testing Prerequisites for sound emission tests Load the dishwasher with 16 standard place settings and use the Normal pro gram Setup for sound emission tests The dishwasher must be set up according to the following specifications ed D o A 820 m Install the dishwasher into an analyzing unit m Secure the front pa
4. A program was not run after dishwasher salt was added Traces of salt have got into the wash cycle m Always run the Express program with the Short program option selected and without any dishware in the dishwasher after adding dishwasher salt The salt reservoir cap has not been screwed on cor rectly m Replace it making sure that it screws back on correctly 61 Frequently asked questions Cleaning the water intake A filter is incorporated in the screw con nection of the water intake valve The filter must be cleaned when dirty other wise insufficient water flows into the wash cabinet A The plastic housing of the water connection contains an electrical component The housing must not be dipped in water Recommendation If the water supply contains a large amount of insoluble substances we recommend fitting a large area filter in the connection between the faucet and the water intake hose threaded union This filter is available from a Miele deal er or Miele Service To clean the filter m Disconnect the dishwasher from the electrical supply Switch off at the mains socket and withdraw the plug m Turn off the water supply m Unscrew the water intake valve 62 m Take the seal ring out of the screw connection m Withdraw the filter using pointed pli ers and rinse clean under running water m Replace the filter and washer making sure they are sitting correctly m Rec
5. If you open the door during the delay start time you must then press the Start button to continue the delay start time The time up until the program starts will count down in the display in hours for durations above 10 hours and in mi nutes for durations below 10 hours When the set time is reached the pro gram selected will start automatically The time remaining will appear in the time display and the indicator light will go out How the Delay Start time is shown in the display up to 59 minutes e g 30 minutes 9 30 1 hour up to 9 hours 30 minutes e g 5 hours 5 08 over 10 hours e g 15 hours 75 Starting a program before the delay start time has elapsed A program can be started before the delay start period has elapsed Proceed as follows m Turn the dishwasher off with the D button m Turn the dishwasher on again with the O button m Select the program you want m Press the Start button The program cycle will begin The Start indicator light will come on 45 Options Optimize Standby Optimize Standby is activated by de fault To save energy the dishwasher will switch off automatically a few minutes after the last time a button has been pressed or after the end of a program The dishwasher will not turn off while a program is running during the delay start period or if there is a fault Optimize Standby can be switched off if yo
6. milk and baby bot tles m Place the bottle holder in the position shown in the bottom basket If placed anywhere else water will not be able to access the bottle prop erly and cleaning results will be im paired 33 Loading the dishwasher Cutlery AG CY Cutlery tray depending on model K 0 m Arrange the cutlery in the tray as TG A WA ho A w Vy VS CRC shown should be grouped in zones one for To make unloading much easier cutlery knives one for forks one for spoons etc Spoon heads should be placed in con tact with at least one of the serrated re tainers on the base of the cutlery tray to m If spoon handles do not fit between ensure that water runs off them freely the holders lay them the other way round The upper spray arm must not be blocked by items which are too big 34 Operation Detergent A Only use detergents formulated for domestic dishwashers Refer to the manufacturer s packaging as to whether Tab products are suitable for the water hardness level in your area Please note that the cleaning and dry ing results of Tab detergents can vary greatly For optimum cleaning and drying re sults use Miele dishwasher detergent and add Miele salt and Miele rinse aid separately See Optional accesso ries Detergent dosage
7. the rinse aid reservoir contains suffi cient rinse aid for 2 3 programs only m Add rinse aid If you only ever use combination prod ucts in your dishwasher you can switch both refill indicators for salt and rinse aid off if you wish See Op tions Refill indicators Setting the rinse aid dosage You can adjust the rinse aid dosage for best results The rinse aid dosage is set in stages from 0 to 6 It is set to 3 at the factory This is the recommended setting The dosage can turn out to be higher than the set value due to the automatic adjustment of the Automatic program If spots appear on dishware and glass ware m Increase the rinse aid dosage If clouding or smearing appears on dishware and glassware m Decrease the rinse aid dosage m Turn the dishwasher off with the D button if it is turned on m Press the Start button and simulta neously switch the dishwasher on using the D button Keep the Start button pressed for at least four seconds until the Start indi cator light comes on If this does not happen start the proce dure from the beginning again m Press the button 3 times The indicator light will flash 3 times at short intervals The set value will appear in the display after P The flashing sequence F 3 will appear in the display This indicates a factory default setting of 3 m Use the Start button to select the set ting required Each press o
8. ASSE 1001 IEC EN DIN 61770 VDE 0700 Part 600 and may be connected to a suit able supply without an extra non re turn valve if national regulations per mit The water pressure flow pressure at the take off point must be between 4 35 145 psi If the water pressure is too high a pressure reducer valve must be fitted After connecting the dishwasher to the water supply check that the wa ter intake is airtight A To avoid any damage to the ap pliance the dishwasher must only be connected to fully vented pipework A The intake hose must not be shortened or damaged in any way as it contains electrical components 69 Water connection Drainage The machine comes equipped with a built in non return valve on the dis charge side to prevent waste water from flowing back into the dishwash er Take the drain line of the dishwasher and attach the drain line as high as possible under the counter rim of the kitchen sink before connecting the end to the drain The loop will serve to prevent a backed up drain or large volume of water in the sink from si phoning back into the dishwasher The dishwasher is supplied with ap prox 5 11 1 5 m of flexible drain hose with an internal diameter of 7 8 22 mm The drain hose can be extended us ing extensions and adapters The drainage length must not be longer than 13 1 1 2 4 m and the delivery head must not exceed 3 3 3 8 1m
9. Compartment holds a maximum of 3 5 tablespoons 50 ml of detergent The marks in compartment II indicate the levels of approximately 1 and 2 tablespoons 20 and 30 ml respective ly The marks indicate the approximate fill level in ml when the door is open in a horizontal position 36 Operation Turning on m Make sure the spray arms are not ob structed m Close the door m Turn on the water supply if it is turned off m Turn the dishwasher on with the D button The Start indicator light flashes and the indicator light comes on next to the program selected Selecting a program Choose your program according to the type of load and the degree of soiling The different programs and their uses are described in the Program Over view chapter m Use the program selection button V to select the program required The indicator light for the program se lected will light up The program duration will appear in hours and minutes in the display You can now select program options see Options If any program options are selected the appropriate indicator lights will also light up 37 Operation Starting a program The dishwasher can be started only if the door is closed m Press the Start button The program will begin The Start indicator light will come on A program should only be canceled in the first few minutes if at all Oth erwise important prog
10. ENGGA aa ete san nette 69 Contents Drainage SOUNC SMISSION TESTING is 25525 apa Ga a AR Da aa E eeaeacgistvanecstasdanesssantenumactetsnees IMPORTANT SAFETY INSTRUCTIONS This dishwasher complies with current safety requirements Inap propriate use can however lead to personal injury and damage to property To avoid the risk of accidents and damage to the dishwasher please read the installation plan and the operating instructions carefully before it is installed and used for the first time They con tain important information on its installation safety use and main tenance Keep the installation plan and the operating instructions in a safe place and pass them on to any future owner Miele cannot be held liable for damage caused by non compli ance with this information IMPORTANT SAFETY INSTRUCTIONS Correct use D This dishwasher is intended for use in domestic households and similar residential environments P This dishwasher is not suitable for outdoor use D It must only be used as specified in these operating instructions for cleaning domestic dishware and cutlery Any other usage is not supported by the manufacturer and could be dangerous gt This appliance is not intended for use by persons including chil dren with reduced physical sensory or mental capabilities or lack of experience and knowledge IMPORTANT SAFETY INSTRUCTIONS Safety with children gt Children must be kept away
11. Gada a aaa nia aa ga aa aa kai aaa a ka aan a it 38 TIME CIS BIAY asasaran ANGGA ge AKAN AN AAN EA ae dearer J NAHAN ANNA AANE EA ANANA RAK HA MEN da 38 Energy management tirant SA KAN GA ANAN NARA EN 39 At the end of the program siens 39 2 Contents WIB nia SOM E T AR E TAN ee NAN 40 Unloading the diShwaSh r is aka Kaka WANA aR KANA KG AA KANAKA ANANG 40 Interrupting a Program a EN KANE KAKARANGAN KEN NRAKA Ka eee 41 Changing a progran 2525220 Litres sent Un SA An kyan panan agan Aa andaan aane an nan aa wa gah aia RES 41 OPUIONS Essen aa dt NANG Nang kana nn TENG a fa nag a aa nai 42 Shon AAN one nT ne E ee eee ey eee eee ene ee 42 Turning off the refill InGICAtONS ss secs aia a aaa a aaa ng a aka aa BANA N AA DAN ENE NE AA a a 43 Delay Start sasa ah saa ki aana ag aaa AAN GAN SAKA ERA WAN KNA a ANA NAH SANA KK Wa 44 Optimize Standby 22 rente ecran a icine etn AA ANNA dad ANG dad eee tne ANAN 46 Factory default settings san daa aaa INNA EEN DANA BAEN BB a AA EN a BINA SAN AAN NA ga a KN 47 Programi OVErVIGW sasaka aa a nanang aaa GEN aa KENA ccna Kaga gua a a aan E TEN aaa Naga Na KA 48 Cleaning and Care anana eae anan anana aane anae 49 Cleaning the wash Cabin Chis is aia as aa nak A SANAN AKAN EA KAR AKA KANANE NGANAN ANAKE KA 49 Cleaning the door and the door seal sessaaaeeesanerenana eaaa nan ana nane ana nenen nenna 49 Cleaning th door front nur N
12. arm There is a rattling noise in the wash cabinet Dishware is moving around in the wash cabinet m Interrupt the program and rearrange loose pieces A foreign object e g a cherry pit has become lodged in the drain pump m Remove the foreign object from the drain pump see Maintenance Cleaning the drain pump and non return valve There is a knocking noise from the water pipe This may be caused by the installation or the diame ter of the water pipe m This has no influence on dishwasher function If in doubt contact a suitably qualified plumber 58 Frequently Asked Questions Poor cleaning results Problem Possible cause and solution The dishes are not clean The dishes were not loaded correctly m See notes in Loading the dishwasher The program was not powerful enough m Select a more intensive program see Program overview Not enough detergent was dispensed m Use more detergent or change your detergent Items are blocking the path of the spray arms m Rearrange the items so that the spray arms can rotate freely The filter system in the base of the wash cabinet is not clean or is not correctly fitted This may cause the spray arm jets to get blocked m Clean and or fit the filter system correctly m Clean the spray arm jets if necessary see Clean ing and care Cleaning the spray arms The non return valve is open and bloc
13. been used previ ously Dishwasher salt In order to achieve good cleaning re sults the dishwasher needs to operate with soft water Hard water results in a build up of calcium deposits on dish ware and in the dishwasher Water supplies with a hardness level higher than 4 gr gal 4 d needs to be softened This takes place automatical ly in the integrated water softener The water softener in the dishwasher is suit able for a water hardness level of up to 73 gr gal 70 d The water softener requires dishwasher salt Depending on the water hardness level lt 22 gr gal or 21 d dishwasher salt is not required if combination tablets are being used see Operation Deter gent A Dishwasher detergent will de stroy the water softener Do not fill the salt container with dishwasher detergent even liquid detergent A Use only special coarse grained dishwasher salt or other pure kitchen salt Other types of salt may contain in soluble components which can dam age the water softener 21 Before using for the first time Filling the salt reservoir Before filling the salt reservoir with dishwasher salt for the first time you must fill it with approx 1 liter 1 qt of water to enable the salt to dis solve Once the dishwasher has been used for the first time there is always suf ficient water in the reservoir m Remove the lower basket and un screw the salt reservoir cap Wa
14. cutlery basket depending on model cut lery is cleaned and dried more efficiently if placed in the basket with the handles downwards However to avoid the risk of injury place knives and forks with the handles upwards D Plastic items which cannot withstand being washed in hot water such as disposable plastic containers or plastic cutlery should not be cleaned in the dishwasher The high temperatures in the dish washer may cause them to melt or lose shape gt If you use the FlexiTimer Delay Start option depending on mod el make sure that the dispenser is dry before adding detergent Wipe dry if necessary Detergent will clog if poured into a damp dis penser and may not be thoroughly dispersed D Please observe the information given in Technical data regard ing the capacity of the dishwasher Accessories gt Use only genuine original Miele parts If spare parts or accesso ries from other manufacturers are used the warranty may become invalid Disposal of your old dishwasher gt Make the door lock inoperative so that children cannot acciden tally shut themselves in Remove or destroy the locking bracket of the door lock and make appropriate arrangements for the disposal of the appliance SAVE THESE INSTRUCTIONS AND PASS THEM ON TO ANY FUTURE USER Guide to the dishwasher Appliance overview NG oe ik
15. door is opened m Close the door and press the Start button The program will continue from the point at which it was interrupted A Water in the dishwasher may be hot Danger of scalding Only open the door if absolutely nec essary and exercise extreme caution when doing so Before closing the door again leave it ajar for approx 20 seconds This will enable the tem perature in the wash cabinet to set tle After that close the door and press the Start button Changing a program If the detergent dispenser flap has already opened do not change the program If a program has already started and you wish to change it proceed as fol lows m Turn the dishwasher off with the button m Turn the dishwasher on again with the O button m Select the program you want and then start it 41 Options Short The Short option reduces the dura tion of programs in which this option is available In order to achieve optimum cleaning results consumption rates are in creased with this option When used in combination with the Rapid program the Short option re sults in a wash program without drying or automatic opening of the door if available m Turn the dishwasher on with the button The Start indicator light flashes m Select a program m Press the button The indicator light will light up m The program can now be started The option selected will remain active for t
16. electric shock Do not modify the plug provided with the appliance if it will not fit the out let have a proper outlet installed by a qualified electrician If there is any question concerning the proper electrical connection or grounding of this appliance to the powersupply please consult a li censed electrician or call Miele s Technical Service Department USA 1 800 999 1360 CDN 1 800 565 6435 Specifications The dishwasher comes equipped with a 4 ft 1 2 m powercord with a molded plug for connection to 120 V 60 Hz 15 A grounded receptacle Water connection The Miele WaterProof System With proper installation the Miele Wa terProof System will protect you from water damage Water intake A Water in the dishwasher must not be used as drinking water The dishwasher may be connected to a cold or hot water supply up to a maximum of 140 F 60 C We would only recommend connec tion to a hot water supply if it is eco nomical e g a solar powered supply When connected to a hot water sup ply all program stages which would otherwise be carried out with cold water will be carried out with hot wa ter The intake hose is approx 4 11 1 5 m long A 1 5 m long flexible metal extension hose pressure tested to 2 030 psi is available as an optional accessory if required A faucet with a 3 4 male thread must be provided on site This appliance is constructed to comply with ANSI
17. for detergent tabs 2X Pre wash To rinse dishes when a complete program is not needed Consumption The consumption values refer to a hot water connection Electric power 0 01 1 0 kWh Water 1 0 48 3 7 gal 3 8 14 Cleaning and care Check and clean your dishwasher Cleaning the door and the door regularly This will help avoid prob seal eme and taulia Bacteria could build up on the door seal and the sides of the dishwasher N All surfaces are susceptible to door as these surfaces are outside the scratching wash cabinet and are not accessed and Contact with unsuitable cleaning cleaned by the spray arm jets agents can alter or discolor all surfa m Wipe the door seals regularly with a damp cloth to remove food deposits m Wipe off any food or drink residues Cleaning the wash cabinet 9 which may have dripped onto the Generally the wash cabinet is self sides of the dishwasher door before cleaning if the correct amount of deter closing it gent is used If however there are lime scale or grease deposits in the cabinet these can be removed with a special dish washer cleaner see Optional accesso ries Follow the instructions on the packaging If you mainly use low temperature pro grams lt 120 F 50 C there is a risk of bacteria and unpleasant odors building up in the wash cabinet To prevent this happening the dishwasher will automat ical
18. m Follow the dosage recommended by the manufacturer on the packaging m Unless directed otherwise use one detergent tab or add 1 1 4 2 table spoons 20 30 ml detergent to compartment Il depending on the level of soiling With very heavy soil ing you can also add a small amount of detergent to compartment m Tabs may not dissolve completely when the Express program if availa ble is used Use only the recommended amount of detergent Continued use of too much detergent may cause machine damage A Dishwasher detergents can cause burning in the nose mouth and throat if swallowed or inhibit breathing Avoid inhaling or swallowing dish washer detergent Keep children away from detergent Keep deter gent out of the reach of children Keep children away from the dish washer when the door is open There could still be detergent residues in the dishwasher Only add detergent just before starting the program and lock the door with the child safety lock depending on model 35 Operation Adding detergent po po m Add the required amount of detergent m Press the opening catch on the de and close the flap tergent dispenser The flap will spring m Make sure that the detergent packag open ing is properly closed after use to The flap is always open at the end of a avoid it getting damp and becoming program lumpy Dispensing aid Compartment holds a maximum of 2 teaspoons 10 ml
19. saving dishwashing This dishwasher is economical in the use of water and electricity For best re sults follow these tips For most economical dishwashing make full use of the baskets without overloading the dishwasher Choose a program that best suits the degree of soiling and the type of dishes being washed Select the Economy program de pending on model for energy saving dishwashing This program is the most efficient in terms of its com bined energy and water consumption at cleaning normally soiled dishware Follow the detergent manufacturer s recommendations on detergent dos age When using powder or liquid deter gent you can use less detergent if baskets are only half full The dishwasher can be connected to a hot water supply for further econo mies If the water is heated by for ex ample solar panels this would be energy efficient However if your water is heated by electricity we would recommend con nection to cold water You can find additional tips on energy saving dishwashing in Miele s guide to dishwashing Before using for the first time Opening the door m To open the door reach under the door grip and pull If the door is opened during operation all functions are automatically interrupt ed A Water in the dishwasher may be hot Danger of scalding Only open the door during operation if absolutely necessary and exercise extre
20. 1 Filling the Salt reservoir 22 lag JI A ae CATON RN ee a a Ra 23 PRIN SQN jo sa Ka GB aa a an SE NR AN Ta EA AN AE aan TA EA NA ter Na A 24 Adding ninsa AIG asasaran aaa apan ian Aah aa dan Na anah I UC 24 RIDSS AIG IMGICAION sorsien een aa a nak ai eee ank ag 25 setting the rinse aid dosage iii crises seers iinet a 25 Loading the dishwasher 2essreevvanniinnenceenenstinnent eses 26 PS a a ta er ea aaa bana aa 26 Loading CxaM ples sasanak inaa ARA KEH ang KA KEN WANG NGANA NANANG HAK ANNA WADUNG BAN NANA Ek GA KA aab Aa Wah 26 Upper baskets tases daman daa agak alec NAN a ies aera ee 29 Adjusting the upper basket ss 30 Lower paskolos semra an aa Ja La sanan a aana A na ag rak nets I aa ak daa a de an 31 G70 Yaaa aa EE aaa BA WANA NGA A KANA AKARANA KAR BANK E tee KAR SANAN KO AA Wana a Nasa eer BAR Bali 34 Cutlery tray depending on model sassasasawana senada aaa an Ena aaa Nagane KENEN ENAK 34 OperatiQn saa nag aa ea aaa aa Na Gaga aka GANG aa ag naa reer ga EN Aa ag aa Na a Nan eer roe 35 DG Ter Gent 2c gan agan aaa na gana a and innana baan baang janan ane geh nak ana ngan aa dan san a ana gah a aan aga anaa 35 Adding d tergent sasana aaa anaa gana AAN KEH SANAN KANEA KE NK AA Aa AAN KA SAGAHI A Waa ANAA aaa AA 36 TUMANG ON sasa aa ag aaa aaa Aa da ANANA AKAN da AA Aga a Aa aa aa carves d AA ENG da a A Aa ANA aa Kagan gae 37 Selecting a Progra EEN os EEN e SEa E ER E EN PEN GR AES 37 Staing APON EE aaa a aaa
21. 50 FILS E SY SUI e anana dana sanan jangan a adane ng an Gagah ga tiens can a Adan da an aa anana andahan Ada a naanin 51 Cleaning the spray arms iii 53 Frequently Asked Questions 54 Technical Problem sasada na NE KENE NAN nr nent etes 54 Water intake fault sise 56 Water drainage Taulit sssusa aa NA RAH KENA A ANAA ANA NA KAR cater Wana kai aa kua Kana 56 General Problem Se asauran anana E e EN ANE KANANG La ka aja NENG EEN Ga Bae 57 NGOIS S abaan ian aaa a ei Raas an aga A aana aa naa rt tee 58 Poor Cleaning M SUITS aring anka aaa ed a AAA ER SAE EEE 59 Frequently asked questions 62 Cleaning the water Intake asas asana aa gana nee EEANN 62 Cleaning the drain pump and non return valve sasana eaaa eaaa aana aa anane aana 63 Customer service eee eee aaa nannan anataet aane anae 64 HRS OES esia saka aga ga anaa a kaa E Aa KE eaaa NA AE TK a lee aa aka an Ba 64 LA ETES TALS ARR gana aranan einen ga a ANA Nga na KA aaa Anaa E E NARAR NA AA AANE An ASA 64 Optional accessories ciiin NGE NANA AN Na gg aa raaa Kaga Na aa 65 Installation Instructions sise 67 Electrical connection aaa anana 68 Water CONNECTION aaa naea kaga NG kaa a AN reste see mener 69 The Miele WaterProof System iii 69 Water Intake 20e net ire E EE nee tint tete en tent e
22. D siecle Operating Instructions Dishwasher To prevent accidents and machine damage read these instructions be fore installation or use en US HGO6 M Nr 10 014 040 Contents IMPORTANT SAFETY INSTRUCTIONS 5 Guide to the dishwasher asus kara aNA KANANE A KAHANAN ANK SAHA KA KAHANAN NGANAN AMAHA BA 14 Appliance OVGrVIGW sasana ang aga aa a a gag ENEG nd tente daa A gag ANG Ka aaa awe Savas 14 Control panel aaa rana aana Nga nn anda I a Aa naa ga aa agan a na aaa ea a jas DAN 15 Caring for the environment nana anaa 16 Disposal of packaging material us 16 Disposal of your old applianCe ss cis saa nag ag aa SEN ag ANENG GG ENG NGAEN a NG 16 Energy Saving diShWwaShing 5 25528 5er nine dent EN ENGGA E ANAN N Na BA NANA KANAAN 16 Before using for the first time 17 Opening the YOO nasa ARE aaa ANA cock Bank Aan Aah canes agenda ak Kan Aak dagan AAS 17 Closing the OOP sasana agan aana eee eee eee dee ete ee eee 17 Child Satety lOCK a aaa aaa a aa aan nn A ee eterna 17 Water SORCGMES ccsisasscscceccrcuneeenzcntineaacesteteedenenseneaeaseabauesdndnsdanessadugauneaiessathasrnanainaesaas 18 Displaying and setting the water hardness level 19 Before using the appliance for the first time you require 21 Dishwasher salt near ent Ne A aaa a aa nen a ne ner aaa Na in 2
23. at the end of the pro gram m The dishwasher can now be opened and unloaded see Unloading the dishwasher A To prevent the risk of steam damage to the counter edging above the dishwasher it is advisable to leave the door closed until you are ready to unload the dishware Alter natively you can open the door fully until the dishware is cool enough to unload Do not leave the door only partially open 39 Operation Turning off At the end of a program m The dishwasher can be switched off at any time using the button Turning the dishwasher off during a pro gram stops the program Turning the dishwasher off during the run up to a delay start time FlexiTimer will also stop the process If the dishwasher is not going to be used for a longer period of time e g while on vacation the water supply should be closed 40 Unloading the dishwasher Dishes tend to break and chip more easily when they are hot Allow the dishes to cool until they are comforta ble enough to handle before unloading them The dishes will cool much faster if you open the door when the program has ended First unload the lower basket then the upper basket and finally the cutlery tray depending on model This will prevent water drops from the upper basket and cutlery tray from fall ing onto the dishes in the lower basket Operation Interrupting a program A program will be interrupted as soon as the
24. ate lots of glasses Installation Instructions Please refer to the Installation Diagram supplied with these instructions To comply with IEC sound testing protocols please contact Miele for additional instructions Information is subject to change Please refer to our website to obtain the most current product specification technical amp warranty information 67 Electrical connection Installation repairs and other work by unqualified persons could be dangerous Check that the voltage frequency and fuse rating shown on the data plate match the household mains supply The power outlet must be accessible after installation Do not use an ex tension cord to connect the dish washer to the mains Danger of over heating See data plate on the right side of the door A damaged power cord must only be replaced with a genuine Miele cord by a Miele service technician Grounding instructions THIS APPLIANCE MUST BE GROUNDED In the event of a malfunction or break down grounding will reduce the risk of electric shock by providing a path of least resistance for the electrical cur rent This appliance is equipped with a cord having an equipment grounding conductor and a grounding plug The plug must be plugged into an appropri ate outlet that is installed and grounded in accordance with all local codes and ordinances 68 Improper connection of the equip ment grounding conductor can result in
25. ault message appears again there is a techni cal fault m Contact Miele Service 55 Frequently Asked Questions Water intake fault Problem Possible cause and solution The Intake Drain indica tor flashes on and off The water supply is turned off m Turn on the water supply all the way The dishwasher stops during a program The Intake Drain indica tor flashes Fault code fi or F13 ap pears in the display Before fixing the fault m Turn the dishwasher off with the D button There is a problem with the water intake m Turn on the water supply fully and start the pro gram again m Clean the water intake filter see Frequently asked questions m The water pressure at the intake is lower than 4 35 psi Contact a plumber Water drainage fault Problem Possible cause and solution The dishwasher stops during a program The Intake Drain indica tor flashes Fault code F11 shows in the display Before fixing the fault m Turn the dishwasher off with the D button There is a problem with the water intake There might be water in the wash cabinet m Clean the filter system see Cleaning and care Filter system m Clean the drain pump see Frequently asked questions m Clean the non return valve see Frequently asked questions m Remove any kink or loop in the drain hose 56 Frequently Asked Questions General prob
26. dishwasher to the higher value 16 gr gal or 15 d in this example It is useful to know your water hardness so that you can provide the service technician with this information in the event of any service calls 18 Enter the water hardness below gr gal d The dishwasher is programmed at the factory for a water hardness level of 1 gr gal 1 d If this setting corresponds to the hard ness of your water you do not need to do anything more However if you have a different water hardness you must adjust the water softener to match your water hardness Before using for the first time Displaying and setting the water hardness level m Turn the dishwasher off with the D button if it is turned on m Press the Start button and simulta neously switch the dishwasher on using the button Keep the Start button pressed for at least four seconds until the Start indi cator light comes on If this does not happen start the proce dure from the beginning again m Press the button twice The indicator light will flash twice at short intervals The value which has been set for the water hardness appears as a figure in the time display see table according to P 7 will start flashing in the time display This is the factory default setting of 1 m Use the Start button to select the val ue which equates to your water hard ness level Each press of the button moves you up a level When th
27. ds m Remove all foreign objects from the non return valve 63 Customer service Repairs For problems that you cannot resolve on your own please contact your Miele dealer or Miele Service The telephone number for Miele is listed at the back of these instruc tions In the event of a fault which you cannot correct yourself please contact the Miele Service Department at the phone number on the back of this booklet 64 Warranty For more information please refer to the included warranty MieleCare USA only MieleCare our Extended Service Con tract program gives you the assurance of knowing that your appliance invest ment is covered by 5 years of worry free ownership MieleCare is the only Extended Service Contract in the industry that guarantees repairs by a Miele Authorized Service Provider using genuine Miele parts On ly genuine Miele parts installed by fac tory trained professionals can guaran tee the safety reliability and longevity of your Miele appliance Please note that unless expressly ap proved in writing by Miele s Service de partment Extended Service Contracts offered by other providers for Miele products will not be recognized by Miele Our goal is to prevent unauthor ized and untrained service personnel from working on your Miele products possibly doing further damage to them you and or your home To learn more about MieleCare Extend ed Service Contract
28. e highest water hardness level is reached the setting starts from the beginning again The setting is now stored in memory m Turn the dishwasher off with the D button 19 Before using for the first time d gr gal i Time d gr gal f Time display display 1 1 2 1 21 22 38 21 2 2 4 2 22 23 40 22 3 3 5 3 23 24 41 23 4 4 7 4 24 25 43 24 5 5 9 5 25 26 45 25 6 6 11 6 26 27 47 26 7 7 13 7 27 28 49 27 8 8 14 8 28 29 50 28 9 9 16 9 29 30 52 29 10 10 18 10 30 31 54 30 11 11 20 11 31 32 56 31 12 13 22 12 32 33 58 32 13 14 23 13 33 34 59 33 14 15 25 14 34 35 61 34 15 16 27 15 35 36 63 35 16 17 29 16 36 38 65 36 17 18 31 17 37 45 39 47 66 80 45 18 19 32 18 46 60 48 63 82 107 60 19 20 34 19 61 70 64 73 109 125 70 20 21 36 20 20 Before using for the first time Before using the appliance for the first time you require Approx 1 liter 1 qt of water Approx 2 lbs 1 kg of dishwasher salt Domestic dishwasher detergent Rinse aid formulated for domestic dishwashers If the water in your area is very soft and constantly lower than 5 gr gal 5 d you do not have to add dish washer salt The prompt to add salt will be switched off automatically Every dishwasher is tested at the fac tory There will be residual water in the appliance from this test It is not an in dication that it has
29. e placed in the cutlery tray or cutlery basket depending on model Some foods may contain natural dyes e g carrots tomatoes or to mato sauce Plastic items in the dishwasher may discolor if large quantities of these foodstuffs find their way into the dishwasher on the dishware The stability of plastic items is not affected by this discolor ation Cleaning silver cutlery in the dish washer may also cause plastic items to discolor Loading the dishwasher Items not recommended for dish washing Wooden cutlery cutting boards and dishware or items with wooden parts Craft items antiques valuable vases and decorative glassware Plastic items which are not heat re sistant the high temperatures in the dishwasher may cause them to melt or lose shape Copper brass tin and aluminum items may discolor or become matt Colors painted over a glaze may fade after a number of washes Delicate glassware and glassware containing lead crystal clouding may occur over time Please note Silverware previously cleaned with a silver polish may still be damp or spot ted at the end of a program where wa ter has not run off smoothly It may need to be rubbed dry with a soft cloth Silver which has been in contact with foods containing sulphur can discolor These include egg yolk onions mayon naise mustard fish and marinades A Aluminum components e g range hood grease filters mu
30. ems Glasses can be arranged along the po sitioning rail of the cup rack to give them some support during the pro gram m Lower the cup rack and lean the glasses against it or double stack smaller pieces 29 Loading the dishwasher Adjusting the upper basket In order to gain more space for taller items the upper basket can be adjusted on three levels with 3 4 2 cm be tween each level The upper basket can also be set at an angle with one side high and the other side low Make sure however that the basket can slide smoothly in and out of the cabinet m Pull the upper basket out To raise the upper basket m Lift the basket until it clicks into place To lower the upper basket m Pull upwards on the levers at either side of the upper basket m Adjust the basket to the desired height and then push the levers se curely back down into position Depending on the setting of the upper basket the following plate dimensions can be accommodated 30 Dishwashers with cutlery tray Upper bas Plate in inches cm l Upper bas Lower bas ket ket Upper 7 7 8 15 12 3 16 31 Middle 6 11 16 11 7 16 17 29 Lower 7 1 2 19 10 5 8 27 Depending on the setting of the upper basket a variety of plate dimensions can be accommodated Loading the dishwasher Lower basket
31. food can get stuck in the spray arm jets and bearings The spray arms should therefore be inspected and cleaned regularly approx every 4 6 months m Turn the dishwasher off Remove the spray arms as follows m Take out the cutlery tray if your dish washer is fitted with one m Push the top spray arm upwards to engage the inner ratchet Then un screw the spray arm m Push the middle spray arm upwards to engage the ratchet Then un screw the spray arm m Remove the lower basket m Pull the lower spray arm firmly up wards to remove it m Use a pointed object to push the food particles that are stuck in the spray arm jets into the spray arm m Rinse the spray arms thoroughly un der running water m Replace the spray arms and check that they rotate freely 53 Frequently Asked Questions With the help of the following guide minor faults in the performance of the appli ance some of which may result from incorrect operation can be put right without contacting Miele Service This will save time and money The following guide may help you to find the reason for a fault and to correct it You should however note the following A Unauthorized or incorrect repairs could cause personal injury or damage to the appliance Repair work to electrical appliances must only be carried out by a suitably qualified and competent person in strict accordance with current local and na tional safety
32. foreign objects A This dishwasher must not be used without all the filters in place Collection of coarse soil may cause the filters to clog The level of soiling and time it takes before the filters need cleaning will vary depending on use m Check the condition of the filters reg ularly and clean them if necessary Filter system m Turn the dishwasher off m Turn the handle counter clockwise to release the filter system m Lift the filter system out of the dish washer 2 Remove any coarse parti cles and rinse the filter well under running water Use a nylon brush if necessary A Ensure that course soil does not get into the circulation system and cause a blockage 51 Cleaning and care To clean the inside of the filter the flap must be opened m Press catches 1 together in the di rection of the arrows as shown and open the filter 2 m Rinse all the filters under running wa ter m Then close the flap so that the catch engages 52 m Replace the filter system so that it lies flat in the base of the wash cabi net m Then turn the handle clockwise until both arrows point towards each oth er This will lock the filter system in place A Take care when you are fitting the filter system that it is secured in position correctly Otherwise coarse soil could get into the circulation system and cause a blockage Cleaning and care Cleaning the spray arms Particles of
33. from the appliance unless they are constantly supervised D Children should be supervised to ensure that they do not play with the appliance Keep small children away from the appliance at all times to avoid the risk of injury There is the risk that children may lock themselves in the dishwasher D If the automatic door opening mechanism depending on model is active keep young children away from the area in which the door opens Danger of injury in the unlikely event of a fault with the open ing mechanism D Danger of suffocation Ensure that any plastic wrappings bags etc are disposed of safely and kept out of the reach of children gt Keep children away from detergents Dishwasher detergents can cause burning in the mouth nose and throat if swallowed or inhibit breathing Keep children away from the dishwasher when the door is open There could still be detergent residues in the cabinet Seek medical attention immediately if your child has swallowed or inhaled detergent IMPORTANT SAFETY INSTRUCTIONS Technical safety gt Installation repair and maintenance work should only be per formed by a Miele authorized service technician Work by unquali fied persons could be dangerous and may void the warranty gt Before installation check the dishwasher for visible signs of dam age Under no circumstances should you use a damaged dishwash er A damaged dishwasher could be dangerous D The electrical safety of this a
34. hat particular program until the set ting is changed 42 Options Turning off the refill indicators If you consistently use a Tab detergent you can deactivate the refill indicators if you wish m Turn the dishwasher off with the D button if it is turned on m Press the Start button and simulta neously switch the dishwasher on using the button Keep the Start button pressed for at least four seconds until the Start indi cator light comes on If this does not happen start the proce dure from the beginning again m Press the button 9 times The indicator light will flash 9 times at short intervals The flashing sequence in the time dis play will show whether the refill indica tors are switched on or off P 1 Refill indicators activated P Refill indicators deactivated m Press the Start button to change the setting The setting is now stored in memory m Turn the dishwasher off with the D button If you switch to using detergent that does not contain salt or rinse aid it is important to remember to add dishwasher salt and rinse aid and to switch the indicators back on 43 Options Delay Start You can set the start time for a pro gram The start time can be delayed between 30 minutes and 24 hours The delay period is shown in 30 mi nutes increments for a delay period be tween 30 minutes and 9 hours 30 mi nutes It is shown in hours for periods longer than th
35. hware to dry With glass protection against corro sion Specially designed cap for precise easy dispensing Dishwasher salt Prevents lime scale on dishware and in the appliance Extra coarse grained 65 Optional accessories Dishwasher care products Miele cleaning and care products pro vide optimum care for your dishwasher Dishwasher cleaner Cleans the dishwasher effectively and thoroughly Removes grease bacteria and un pleasant odors Ensures excellent dishwashing re sults Dishwasher descaler Removes heavy lime scale deposits Mild and gentle with natural citric acid Dishwasher conditioner Removes odors lime scale and light deposits Maintains the elasticity and leak tightness of the seals Dishwasher freshener Neutralizes unpleasant odors Fresh pleasant lime and green tea scent Easy to attach to the dishwasher basket Very economical lasts for 60 wash cycles 66 Accessories Some accessories may be supplied as standard depending on model Cappuccinatore insert The Cappuccinatore insert can be used for cleaning the individual parts of the Miele Cappuccinatore in the dishwash er Small cutlery basket This small basket for the lower basket can be used for additional cutlery in cluding ladles and small parts Insert for glasses The insert for glasses fits in the lower basket and is designed to accommo d
36. indicator light will flash once at a long interval and then 9 times at short intervals The flashing sequence in the display in dicates whether a setting has been changed from its factory default P 7 All settings are set to factory de fault settings P 9 At least one setting has been changed m To reset the dishwasher to the factory default settings press the Start but ton The setting is now stored in memory m Turn the dishwasher off with the D button 47 Program overview Program When to use Program seguence res wash Main wash Interim rinse Final rinse Drying Normal Program for regular use to completely wash a full load of normally soiled dish ware with the ability to ad just energy and water con sumption based on the soil load of the dishware If re quired X If re quired X Pots amp Pans For heavily soiled dishware and normally soiled pots pans and utensils with dried on residue use 20 more detergent than rec ommended 2X China amp Crystal GlassCare program for temperature sensitive glasses and dishes with light soiling Use 50 of the detergent amount SaniWash Express To sanitize dishware e g baby bottles cutting boards and preparation dishware Quick program for lightly soiled dishware e g party dishware or to remove salt traces from the wash cabi net after refilling salt not suitable
37. is When using the Delay Start function make sure that the detergent com partment is dry before adding deter gent Wipe dry with a cloth if neces sary If the compartment is wet powder detergent can become lum py and stick to the dispenser with the result that it is not fully dis pensed Do not use liquid detergent when se lecting Delay Start as it can run into the dishwasher before it is required A To prevent children coming into contact with dishwasher detergent Add the detergent immediately be fore starting the program i e before activating the delay start with the Start button Then lock the door with the child safety lock 44 m Turn the dishwasher on with the button The Start indicator light flashes m Select the desired program m Press the button The last delay start time used will ap pear in the time display The indica tor light will light up m Set the required delay start time us ing the button If you keep the button pressed the time will increase automatically up to 24 hours To get back to 3 hours press the button twice m Press the Start button The Start indicator light will come on Options If Optimize Standby is switched on see Options Optimize Standby the time display will go out after a few minutes leaving just the Start indica tor light flashing slowly Press any button to switch the display back on again for a few minutes
38. ked Dirty water has flowed back into the wash cabinet m Clean the drain pump and the non return valve see Frequently asked questions Smearing appears on glassware and cutlery There is a bluish sheen on the surface of glass ware film can be wiped off The rinse aid dosage is set too high m Decrease the dosage see Before using for the first time Rinse aid 59 Frequently Asked Questions Problem Possible cause and solution Dishware is not dry or cutlery and glasses are spotty The rinse aid dosage is set too low or the rinse aid reservoir is empty m Replenish the reservoir increase the dosage or change the brand of rinse aid see Before using for the first time Rinse aid Dishware was taken out of the cabinet too soon m Leave it in for longer see Operation Combination tabs have been used which have im paired drying performance m Change your detergent or replenish the rinse aid see Before using for the first time Rinse aid Glasses have a brown ish blue discoloration the deposit cannot be wiped off Detergent deposits m Switch to another detergent Glasses are dull and discolored the deposit cannot be wiped off The glassware is not dishwasher safe The surfaces are affected m There is no remedy Purchase glassware which is dishwasher safe Tea or lipstick stains have not been com pletely removed Plastic parts a
39. lems Problem Possible cause and solution The indicator lights and time display are dark The dishwasher has switched off automatically to save energy m Turn the dishwasher on again with the button Detergent residue is left in the dispenser at the end of a program The dispenser was still damp when detergent was added m Make sure the dispenser is dry before adding de tergent The dispenser cover cannot be closed Detergent residue is blocking the latch m Remove the detergent residue The inside of the door and or the interior walls are wet after a program has finished This is caused by the drying system and does not in dicate a fault The moisture will dissipate after a while Water remains in the wash cabinet at the end of a program Before fixing the fault m Turn the dishwasher off with the D button The filter system in the wash cabinet is clogged m Clean the filter system see Cleaning and care Filter system The drain pump or non return valve is blocked m Clean the drain pump or the non return valve see Frequently asked questions The drain hose is kinked m Remove the kink 57 Frequently Asked Questions Noises Problem Possible cause and solution There is a knocking noise in the wash cabi net A spray arm is hitting the dishware m Interrupt the program and rearrange the items which are obstructing the spray
40. ltage and frequen cy matches the electrical supply before connecting the dishwasher to the mains Consult a qualified electrician if in any doubt gt Do not connect the dishwasher to the electrical supply until it has been fully installed and any adjustment has been made to the door springs D The dishwasher may only be operated if the door opening mecha nism is working correctly Otherwise there could be a risk of danger while the automatic door opening mechanism depending on model is active To check that the door opening mechanism is working correctly The door springs must be adjusted equally on both sides They are correctly adjusted when the door remains stationary when left half open approx 45 opening angle It is also important that the door cannot fall open The door locking pins automatically retract when the door opens at the end of the drying phase gt Do not connect the appliance to the electrical supply by a multi socket adapter or an extension lead These do not guarantee the re quired safety of the appliance e g danger of overheating D This appliance must not be installed and operated in a non sta tionary location e g on a ship gt Do not install the dishwasher in a room where there is a risk of frost Frozen hoses may burst or split The reliability of the electronic module may be impaired at temperatures below freezing point gt The plastic housing of the water connection contain
41. ly increase the temperature in the fi nal rinse of the selected program after several programs using low tempera tures have been run m Clean the filters in the wash cabinet regularly 49 Cleaning and care Cleaning the door front A If soiling remains longer it may happen that the surfaces can be come discolored or changed Remove any soiling immediately m Clean the front with a solution of warm water and a little dishwashing liquid applied with a soft sponge Wipe the surfaces dry using a soft cloth A Glass cleaners may be used to clean the exterior However do not allow them to sit or puddle this can cause damage to the surface Remove the cleaner promptly 50 To better maintain your appliance avoid the following Cleaning products containing soda ammonia acid or chloride Descaling agents Abrasive cleaning products such as scouring powder scouring liquid or pumice stones Cleaners containing solvents Stainless steel cleaners Dishwasher cleaner Oven cleaners Glass cleaner Hard abrasive brushes or sponges e g pot scourers brushes or spong es which have been previously used with abrasive cleaning agents Eraser sponges Sharp metal scrapers Steel wool Steam cleaning appliances Cleaning and care Filter system The filter system in the base of the wash cabinet prevents food from being redeposited on dishes It also protects the circulation pump from damage caused by
42. me caution when doing so Closing the door m Push the baskets in m Then lift the door upwards and push until it clicks into position A Danger of crushing injuries Do not put your hand inside the door as it is closing Child safety lock Use the safety lock to prevent children from opening the dishwasher door m To lock the door push the slide un derneath the door grip to the right m To unlock the door push the slide to the left 17 Before using for the first time Water softener In order to achieve good cleaning re sults the dishwasher needs to operate with soft water Hard water results in a build up of calcium deposits on dish ware and in the dishwasher Water supplies with a hardness level higher than 4 gr gal 4 d needs to be softened This takes place automatical ly in the integrated water softener The water softener in the dishwasher is suit able for a water hardness level of up to 73 gr gal 70 d The water softener requires dish washer salt Depending on the water hardness level lt 22 gr gal or 21 d dish washer salt is not required if combi nation tablets are being used see Operation Detergent The dishwasher must be program med for the water hardness in your area Your local water supplier can tell you the water hardness level in your area Where the water hardness fluctuates e g between 10 16 gr gal 10 15 d always program the
43. mouth and throat if swallowed or inhibit breathing Seek medical attention immediately if detergent has been swallowed or in haled gt Avoid leaving the door open unnecessarily as someone could trip over it and be injured by it gt Do not sit or lean on the opened door This could cause the dish washer to tip and be damaged and you could get injured gt Dishes can be very hot at the end of a program Allow them to cool until they are comfortable enough to handle before unloading gt Only use detergent and rinse aid formulated for domestic dish washers Do not use dishwashing liquid gt Do not use commercial or industrial detergents as these may cause damage and there is a risk of a severe explosive chemical re action Such as an explosive oxyhydrogen gas reaction gt Do not fill the rinse aid reservoir with powder or liquid detergent This will cause serious damage to the reservoir gt Inadvertently filling the salt reservoir with powder or liquid dish washer detergent will damage the water softener Make sure you have picked up the correct packet of dishwasher salt before filling the salt reservoir gt Only use special coarse grained dishwasher salt for reactivation Do not use other salts such as cooking salt agricultural grade or gritting salt These may contain insoluble additives which can impair the functioning of the water softener 12 IMPORTANT SAFETY INSTRUCTIONS gt In an appliance with a
44. n the button moves you up a level After reaching the highest value the counter starts from the be ginning again The setting is now stored in memory m Turn the dishwasher off with the D button 25 Loading the dishwasher Tips Remove coarse food residues from the dishware There is no need to rinse items under running water A Do not wash items soiled with ash sand wax grease or paint in the dishwasher These will damage the dishwasher Dishware can be loaded anywhere in the baskets but the following notes should be observed Do not place dishes or cutlery inside other pieces They will cover each other Load the dishware so that water can access all surfaces This ensures that they get properly cleaned Make sure that all items are securely positioned Hollow items such as cups glasses pans etc must be inverted in the basket Tall narrow hollow items e g champagne glasses should be placed in the center of the basket to ensure better water coverage Concave items such as mugs or bowls should be placed at an angle so that the water can run off The spray arms must not be blocked by items which are too tall or hang through the baskets If in doubt test for free movement by manually rotat ing the spray arms 26 Make sure that small items cannot fall through the holders in the bas kets Small items e g lids should there fore b
45. nel 71 Sound emission testing m Push the provided fleece strips depending on model under the toe kick until it is flush with the appliance feet m Push the toe kick into place in such a way that it is flush with the door front 72 Sound emission testing m Remove the protective film from the provided insulating strip depending on model m Push the insulating strip into the front top edge of the toe kick 73 Please have the model and serial number of your appliance available before contacting Technical Service U S A Miele Inc National Headquarters 9 Independence Way Princeton NJ 08540 Phone 800 843 7231 609 419 9898 Fax 609 419 4298 www mieleusa com Technical Service amp Support Nationwide Phone 800 999 1360 Fax 888 586 8056 TechnicalService mieleusa com Miele www miele shop com Miele Canada Importer Miele Limited Headquarters and Miele Centre 161 Four Valley Drive Vaughan ON L4K 4V8 www miele ca Customer Care Centre Phone 800 565 6435 905 532 2272 customercare miele ca Germany Manufacturer Miele amp Cie KG Carl Miele StraBe 29 33332 Gutersloh G 4700 en US M Nr 10 014 040 04
46. onnect the water intake valve to the faucet making sure it goes on correctly and is not cross threaded m Turn on the water supply If water leaks out the screw connection may not be connected securely or it may have been screwed on at an angle m Unscrew and reconnect the water in take valve correctly Frequently asked questions Cleaning the drain pump and non return valve If the water has not been pumped away at the end of a program the drain pump or the non return valve might be blocked They are however easy to clean m Turn off the dishwasher and pull the plug m Take the filter system out of the wash cabinet See Cleaning and care Cleaning the filters The drain pump is beneath the non re m Scoop the water out of the cabinet turn valve see arrow using a suitable container or utensil m Remove all foreign objects from the drain pump glass or bone splinters Before returning the non return valve check that the drain pump is not blocked Spin the propeller sever al times in both directions to check for obstructions m Carefully reinsert the non return valve and secure it with the locking clamp A Make sure the locking clamp clicks into place A Be careful not to damage any delicate components when cleaning the drain pump and the non return m Lift the non return valve up and out valve 2 and rinse well under running water m Press the catch for the non return valve inwar
47. ppliance can only be guaranteed when continuity is complete between it and an effective grounding system It is most important that this basic safety requirement is present and regularly tested and where there is any doubt the elec trical system in the house should be checked by a qualified electri cian Miele cannot be held liable for the consequences of an inadequate grounding system e g electric shock D Reliable and safe operation of this dishwasher can only be assur ed if it has been connected to the electrical supply D The dishwasher must only be plugged into the electricity supply via a Suitable switched socket using a 3 pin plug with a grounding contact it must not be hard wired The electrical socket must be easily accessible after the dishwasher is installed so that it can be disconnected from the electricity supply at any time gt There must be no electrical sockets behind the dishwasher There is a danger of overheating and fire risk if the dishwasher is pushed up against a plug D The dishwasher must not be installed under a cooktop The high radiant temperatures which are sometimes generated by a cooktop could damage the dishwasher For the same reason it should not be installed next to open fires or other appliances which give off heat such as heaters etc IMPORTANT SAFETY INSTRUCTIONS gt To avoid the risk of damage to the dishwasher make sure that the connection data on the data plate fuse rating vo
48. ram stages could be omitted 38 Time display The duration of the program selected appears in hours and minutes in the display before the program begins Dur ing the program the time left until the end of the program is displayed The program duration displayed may vary with the same program It is influ enced by among other things the wa ter temperature at each intake the re activation process the type of deter gent the amount of dishware and the amount of soiling When a program is selected for the first time the display shows an average time for a cold water intake The times shown in the program over view refer to standard test loads and temperatures Each time a program is run the elec tronic module calculates the program duration required according to the tem perature of the water taken into the dishwasher and the amount of dish ware Operation Energy management To save energy the dishwasher will switch off automatically 10 minutes af ter the last time a button has been pressed or 10 minutes after the end of the program see Options Optimize Standby m Press the D button to switch the dishwasher back on The dishwasher will not turn off while a program is running during the delay start period or if there is a fault At the end of the program The program has finished when 9 99 appears in the display The drying fan may continue to run for a few minutes
49. re discol ored The wash temperature of the selected program was too low m Select a program with a higher wash temperature The bleaching effect of the detergent is too low m Switch to another detergent Natural dyes e g from carrots tomatoes or ketchup may be the cause The amount of detergent used or its bleaching effect was not sufficient to deal with natural dyes m Use more detergent see Operation Detergent Discoloration is irreversible 60 Frequently Asked Questions Problem Possible cause and solution White residue is visible on dishware and cut lery clouding occurs on glassware this film can be wiped off The rinse aid dosage is too low m Increase the dosage see Before using for the first time Rinse aid The salt reservoir is empty m Fill the salt reservoir see Before using for the first time Dishwasher salt The salt reservoir cap has not been screwed on cor rectly m Replace it making sure that it screws back on correctly An unsuitable Tab detergent has been used m Change your detergent The water softener is programmed to too low a water hardness level m Program the water softener for harder water see Before using for the first time Water softener There are rust stains on the cutlery The affected items are not corrosion resistant m There is no remedy Purchase cutlery which is dishwasher safe
50. regulations The manufacturer cannot be held liable for unauthor ized work Technical problems Problem Possible cause and solution After the dishwasher is The dishwasher is not plugged in turned on with the D m Insert the plug button the Start indica _ tor light does not flash The circuit breaker has tripped m Reset the fuse see data plate for the correct fuse rating The dishwasher stops The circuit breaker has tripped during a program m Reset the fuse see data plate for the correct fuse rating m If the circuit breaker trips again contact Miele Service 54 Frequently Asked Questions Problem Possible cause and solution The Intake Drain and Rinse Aid indicator lights are flashing at the same time Fault number FXX ap pears in the display Fault F 32 The drain pump is still running even with the door open There may be a technical fault m Turn the dishwasher off with the D button m Turn the dishwasher back on after a few seconds m Select the desired program m Press the Start button If the indicator lights flash again there is a technical fault m Contact Miele Service The WaterProof System has reacted m Turn off the water supply m Contact Miele Service Fault 778 A fault has occurred in the circulation pump m Turn the dishwasher off for at least 30 seconds with the button m Turn the dishwasher back on If the f
51. s please contact your appliance dealer or visit us online at http www mieleusa com Optional accessories Dishwasher detergent and rinse aid as well as cleaning and care products are available as optional accessories All the products are designed for use with Miele dishwashers These and many other useful products can be ordered via the Miele website or from Miele see end of this manual for contact details Dishwasher detergent rinse aid and salt When you decided to buy a Miele dish washer you chose excellent quality and performance However ensuring that your dishwasher always delivers the best possible results will also depend on your choice of dishwasher deter gent rinse aid and dishwasher salt as cleaning results can vary depending on the brand used With Miele CareCollection products you can be sure of optimum results as these products have been specially de signed for Miele dishwashers Detergent tabs Sparkling results even with stubborn food deposits Combination product with other components such as rinse aid salt and glass protection additives Phosphate free safe for the envi ronment Water soluble wrapping no need to unwrap Powder detergent With active oxygen for thorough cleaning With enzymes which are effective even in low temperature programs With glass protection against corro sion Rinse aid For gleaming glasses Helps dis
52. s an electrical valve The housing must not be dipped in water There are live wires in the water intake hose Do not shorten the water intake hose even if it is too long IMPORTANT SAFETY INSTRUCTIONS D The built in WaterProof System offers reliable protection against water damage if the following conditions are met Proper installation Proper maintenance of the dishwasher or replacement of the parts in case of noticeable damage Closing of the water valve during longer absences for example vacation The WaterProof System will work even if the appliance is switched off However the appliance must remain connected to the electricity supply P The water pressure flow pressure at the connection point must be between 4 35 145 psi gt A damaged appliance could be dangerous If the dishwasher gets damaged turn off the electrical supply and contact Miele D The manufacturer s warranty will be invalidated if the appliance is not repaired by a Miele authorized service technician gt Defective components should be replaced by Miele original parts only Only with these parts can the manufacturer guarantee the safe ty of the appliance gt During installation maintenance and repair work the appliance must be disconnected from the electrical supply turn it off and with draw the plug from the socket gt If the connection cable is damaged it must be replaced with a special cable of the same type a
53. st not be cleaned with a commercial or in dustrial cleaning agent These may damage the material Tip When purchasing new dishware and cutlery make sure they are dish washer safe Glass care Clouding may occur on glasses after frequent washing If delicate glass ware is washed in the dishwasher ensure that only very low tempera tures are used see program chart or a special glass care program is used depending on model This will re duce the risk of clouding Purchase glassware which is dish washer safe e g Riedel glassware Use detergents with glass protective additives e g Miele CareCollection tabs Visit http www mieleglass care com international en glasscare english for more information on glass care 27 Loading the dishwasher Loading examples With models with cutlery tray 10 standard place settings Upper basket Lower basket Cutlery tray depending on model 28 Loading the dishwasher Upper basket A For safety reasons do not oper ate the dishwasher without the upper and lower baskets in place m Use the upper basket for small light weight and delicate items such as cups saucers glasses dessert bowls etc Shallow pans or casserole dishes can also be placed in the upper basket Adjustable cup rack depending on model EN Li D A SY m Raise the rack to make room for tall it
54. ter will run out of the reservoir when the cap is removed It should therefore only be removed in order to refill the salt reservoir m Fill the reservoir with approx 1 liter 1 qt of water first use only 22 m Place the funnel provided over the salt reservoir and carefully fill with salt until the reservoir is full The salt reservoir holds approx 2 lbs 1 kg of salt depending on the brand used Clean any excess salt from around the reservoir opening and then screw the cap on again firmly Immediately after filling the salt reser voir run the Express program with the Short program option selected and without any dishware in the dish washer to remove any traces of salt from the cabinet Before using for the first time Salt refill indicator m Fill the salt reservoir with dishwasher salt when the Salt indicator light comes on If it comes on during a program wait until the end of the program A Risk of corrosion Immediately after filling the salt res ervoir run the Express program with the Short program option selected and without any dishware in the dishwasher to remove any traces of salt from the cabinet After the salt reservoir has been filled the refill indicator may still be lit up if the salt concentration has not yet reached the correct level It will go out when the correct concentration is reached The salt refill indicator will be switched off if you have programmed the dish
55. u prefer If you do this the duration before the dishwasher switches off au tomatically increases to 6 hours Doing this will increase energy consumption m Turn the dishwasher off with the D button if it is turned on m Press the Start button and simulta neously switch the dishwasher on using the button Keep the Start button pressed for at least four seconds until the Start indi cator light comes on If this does not happen start the proce dure from the beginning again 46 m Press the button 8 times The indicator light will flash 8 times at short intervals The flashing sequence in the display shows whether or not Optimize Stand by is activated PI Optimize Standby activated PU Optimize Standby deactivated m Press the Start button to change the setting The setting is now stored in memory m Turn the dishwasher off with the D button Options Factory default settings If you have altered any settings from the factory default you can reset them back to the factory default settings as follows m Turn the dishwasher off with the D button if it is turned on m Press the Start button and simulta neously switch the dishwasher on using the button Keep the Start button pressed for at least four seconds until the Start indi cator light comes on If this does not happen start the proce dure from the beginning again m Press the button 19 times The
56. vailable from Miele by a Miele au thorized service technician only 10 IMPORTANT SAFETY INSTRUCTIONS Proper installation D The dishwasher must be installed and connected in compliance with the installation plan gt Be careful when installing the dishwasher Wear protective gloves to avoid injury on any sharp metal components gt The dishwasher must be correctly aligned horizontally to ensure problem free operation P In order to ensure stability built under and integrated dishwash ers must only be installed under a continuous counter which is se cured to adjacent cabinetry If you want to convert your freestanding dishwasher to a built un der U model you will need to order the appropriate conversion kit If you remove the existing toe kick you must replace it with a U model plinth This is necessary to avoid the risk of injury caused by protruding metal parts D The door springs must be adjusted equally on both sides They are correctly adjusted when the door remains stationary when left half open approx 45 opening angle It is also important that the door cannot fall open The appliance may only be used with correctly adjusted door springs IMPORTANT SAFETY INSTRUCTIONS Proper use gt Do not use solvents in the dishwasher Danger of explosion gt Do not inhale or ingest powder detergent Dishwasher detergents contain irritant or corrosive ingredients which can cause burning in the nose
57. washer for a water hardness below 5 gr gal 5 d If you only ever use combination prod ucts in your dishwasher you can switch both refill indicators for salt and rinse aid off if you wish see Op tions Refill indicators If you switch to using detergent that does not contain salt or rinse aid it is important to remember to add dishwasher salt and rinse aid and to switch the indicators back on 23 Before using for the first time Rinse aid Rinse aid is needed to prevent spotting on dishes and glassware The rinse aid is filled in the reservoir and the set amount will be automatically dosed A Filling the rinse aid reservoir with detergent will damage the reservoir Only pour rinse aid formulated for residential dishwashers into the res ervoir When using Tab detergents rinse aid is not needed m Add rinse aid only until it is visible in the opening Addi i id d ek ana The rinse aid reservoir holds approx 3 7 oz 110 ml m Close the flap firmly so that it clicks into place Otherwise water can enter the rinse aid reservoir during a pro gram m Wipe up any spilled rinse aid This prevents over foaming occurring dur ing the next program m Press the button on the lid of the rinse aid reservoir in the direction of the arrow until the flap springs open 24 Before using for the first time Rinse aid indicator When the Rinse Aid indicator lights up
Download Pdf Manuals
Related Search