Midway Video Game Machine (VGM) None User's Manual
Contents
1. p LL 2 CCI N TFIID E Fe OPERATIONS ARCTIC THUNDER CHAPTER 1 OPERATION SAFETY INSTRUCTIONS The following safety instructions apply to operators and service personnel Read these instructions before servicing or preparing the Video Game Machine VGM for play Other safety instructions appear through out this manual DEFINITIONS OF SAFETY TERMS e DANGER indicates an imminent hazard If you fail to avoid this hazard it WILL cause death or serious injury e WARNING indicates a potential hazard If you fail to avoid this hazard it COULD cause death or serious injury e CAUTION indicates a potential hazard If you fail to avoid this hazard it MAY cause minor or moderate injury CAUTION also alerts you about unsafe practices e NOTE indicates information of special importance The VGM contains glass and fragile electronic devices Use appropriate care when transporting Avoid rough handling when moving the cabinet Do not move with the power switched on y WARNING TRANSPORTING GAMES WARNING DISCONNECT POWER Always turn the power OFF and unplug the VGM before attempting service or adjust ments unless otherwise instructed Installing or repairing boards with power switched on can damage components and void the warranty WARNING GROUND GAMES Avoid electrical shocks Do not plug in a VGM until you have inspected and properly grounded it Only plug this game into a grounded three w2. no errors are found the game will automatically enter the attract mode of operation scenes and sounds from typical races player s scores messages etc Open the coin door Press and hold the Begin Test button on the operator control switch panel to enter the menu system Wait until the Main Menu screen appears on the monitor ARCTIC THUNDER 7 CHAPTER 1 OPERATION TYPICAL COIN DOOR SWITCH LOCATION 19 Follow on screen instructions to select Diagnostics then choose SWITCH TESTS Follow the on screen instructions to verify that each of the controls is operational If no errors are found the controls should function well 20 Return to the Diagnostics screen then choose CONTROLLER TEST Follow the on screen instruc tions to verify the presence of steering resistance If no errors are found the aim will be good 21 Return to the Main Menu screen and then choose EXIT The game will automatically enter its attract mode of operation scenes and sounds from typical races player s scores messages etc 22 Insert currency or tokens and play a game Change the volume and make any other adjustments Close and lock all open doors Tighten the leveler nuts and engage the caster locks MAINTENANCE e Viewing Glass It is not necessary to switch off power to the game to clean the glass Apply a mild glass cleaner to a clean cloth or sponge and wipe the viewing glass Do not apply the cleaner di
3. A very small portion of the population has a condition which may cause them to experi ence epileptic seizures or have momentary loss of consciousness when viewing certain kinds of flashing lights or patterns that are present in our daily environment These per sons may experience seizures while watching some kinds of television pictures or play ing certain video games People who have not had any previous seizures may nonetheless have an undetected epileptic condition y CAUTION USE CARE WHEN SHIPPING HARD DISKS If you or anyone in your family has experienced symptoms linked to an epileptic condi tion e g seizures or loss of awareness immediately consult your physician before using any video games We recommend that parents observe their children while they play video games If you or your child experience the following symptoms dizziness altered vision eye or muscle twitching involuntary movements loss of awareness disorientation or convulsions DISCONTINUE USE IMMEDIATELY and consult your physician ARCTIC THUNDER 3 CHAPTER 1 OPERATION PRODUCT SPECIFICATIONS Operating Requirements Location Electrical Power Temperature Humidity Domestic 120VAC 60Hz 4 0 Amps 32 F to 100 F Not to exceed 95 relative Foreign 230VAC 50Hz 2 0 Amps 0 C to 38 C Japan 100VAC 50Hz 4 0 Amps Cabinet Statistics Shipping Dimensions Shipping Weight Approx Design Type Width 30 76 2 cm 350Lbs 158kg Main C
4. An extra padlock may be installed to secure rear door Locate hasp Remove the two lock bracket nuts from inside the cabinet above the rear door opening Slide the hasp bracket onto the bolts so that it protrudes from the hole in back of the cabinet then reinstall nuts 6 MIDWAY AMUSEMENT GAMES LLC 14 15 CHAPTER 1 OPERATION PADLOCK BRKT LOCK PLATE KEY LOCK ERK TYPICAL REAR DOOR HASP INSTALLATION Modify the lock plate at the top of the rear door Remove the bolts and nuts from the lock plate then rotate the plate so that the slot will be above the door Reinstall the bolts and nuts and tighten firmly Reinstall the rear door onto the cabinet and close it Lock the rear door and remove the key If required install the extra padlock through the hasp at this time Install the screws at the top and sides of the rear door and tighten snugly Leave the remaining doors open at this time S lt a LINE CORD INSTALLA TION The power cord is packed in with the spare parts Insert a portion of the line cord in the cord clamp leaving enough slack for the cord Match the holes on the IEC plug with the prongs in the receptacle and push firmly to seat the line cord Plug the game into a grounded 3 terminal AC wall outlet Switch on power to the game using the ON OFF switch located on the upper left top of the cabinet when viewed from the player s position The game will power up and begin its self test If
5. abinet Sit On Dedicated Video Game Depth 62 157 4 cm 125Lbs 57kg Seat Assy Machine with Steering Feedback Height 78 198 cm Game Characteristics Player Variables Operator Variables Diagnostics 1 to 4 players per VGM with Linking Coinage Play Mode Difficulty Automatic Power Up Self Test High Score Recognition Volume Audits Statistics Manual Multi Level Menu System Suitable for All Ages AAMA Certified Equipment Characteristics Video Display Monitor x OR VGA Resolution gt 27 68 6 cm CRT Audio System Digital Stereo 5 12 7 cm Coaxial Full Range Speakers 78 3 16 Currency Acceptors 2 Coin Mechanisms Dollar Bill Validator Ready Xo Electronic Coin Acceptor Ready PRODUCT CONFIGURATION Stand Alone Video Game Machine Each VGM is ready to play right out of the box Operators may use the menu screens in the game menu system to determine some player variables in advance or leave the choices up to the players Linked Video Game Machines Linking allows players to compete against each other on a single course Operator menus are used the same way as in stand alone game machines Crossover couplers and linking cables to connect two VGMs are factory installed Use an optional 10 base T ethernet hub to interconnect up to four VGMs MIDWAY AMUSEMENT GAMES LLC CHAPTER 1 OPERATION SET UP 1 Remove all items from shipping containers and set them aside Remove all packaging material Insp
6. ect exterior of the main cabinet and seat pedestal for any damage WARNING Cabinet is top heavy Do not push against plastic parts during movement Remove keys from controller assembly Unlock and open rear door coin box and cash box Electrical cords mechanical components and assorted spare parts are packed inside cash box Casters and leg levelers for the cabinet and pedestal are packed inside of a box with the seat pedestal Locate casters leg levelers and related mounting hardware Install one nut onto each leg leveler Tilt main cabinet as needed to locate threaded holes in underside of cabinet Install a leveler and nut into each hole Do not tighten nuts at this time Repeat these steps for seat pedestal as well Install the provided swivel casters Install the six 6 swiveling casters on the main cabinet and seat pedestal as shown in the illustration below Install provided locking casters Install the two 2 locking casters on seat pedestal as shown in the illustration below LEVELER PLATE LOCATION OF CASTERS AND LEVELER ARCTIC THUNDER 5 CHAPTER 1 OPERATION 7 Roll cabinet to its intended location maintaining clearance between the cabinet and walls drapes other games or obstructions 8 Locate the pedestal assembly mounting rails and rubber bumper spacers which are shipped along with the hardware inside a cash box 9 Install rubber bumpers Rubber bumpers are used to
7. ges guide the operator through tasks CABINET SWITCHES e ON OFF SWITCH is located on the top right hand side of cabinet REMOTE MONITOR ADJUSTMENTS knobs are located inside coin vault Use the monitor test screens with these controls to adjust video image size brightness contrast etc ARCTIC THUNDER 9 CHAPTER 1 OPERATION CONTROL BUTTONS e TEST BUTTON activates game Menu System Press the Test button to access the Main Menu and select individual diagnostics audits utilities etc e VOLUME UP BUTTON is used to move up through menu selections or adjustment items as well as to increase volume level in game play e VOLUME DOWN BUTTON is used to move down through menu selections or adjustment items as well as to decrease volume level in game play e SERVICE CREDIT BUTTON is used to allot credits without affecting a game s bookkeeping total This button is also used to exit a menu selection or return to the main menu 10 MIDWAY AMUSEMENT GAMES LLC
8. ire outlet Do not use a cheater plug or cut off the ground pin on the line cord WARNING AVOID ELECTRICAL SHOCKS The VGM system does not utilize an isolation transformer Internal cabinet AC is not iso lated from the external AC line WARNING HANDLE FLUORESCENT TUBE AND CRT WITH CARE If you drop a fluorescent tube or CRT and it breaks it will implode Shattered glass can fly eight feet or more from the implosion CAUTION CHECK POWER SELECTOR LAMP Set the 115 230VAC selector on the power supply for the correct line voltage Check the selector setting before switching on the VGM Verify that the fluorescent lamp assembly is correct for the local line voltage CAUTION USE PROPER FUSE Avoid electrical shock Replacement fuses must be identically rated Fuse voltage and current ratings must be identically rated to the original fuse Fr t e e B 2 MIDWAY AMUSEMENT GAMES LLC CHAPTER 1 OPERATION CAUTION ATTACH CONNECTORS PROPERLY Be sure board connectors mate properly If connectors do not slip on easily do not force them A reversed connector may damage the VGM and void the warranty Connector keys only allow a connector to fit one set of pins on a board The hard disk drive must be packed in an anti static bag When shipping the drive for repair or replacement pack it in an approved container P N 08 8068 Do not stack or drop hard disk drives WARNING HAZARD TO EPILEPTICS
9. maintain a 3 16 space between the pedestal and cabinet assembly and are essential in absorbing vibration Insert one bumper using a twisting motion into each of the pre drilled holes located along the bottom edge of main cabinet assembly 10 Install pedestal mounting rails Orient the mounting rail so that the pre attached rubber bumpers face outward then insert rail Fasten rail in place with the hardware provided If necessary refer to illustra tion for proper placement 11 Roll pedestal section near main cabinet align opening in the pedestal with the ends of the rails mounted in main cabinet Slide the pedestal forward onto extended mounting rails leaving enough space to attach the wiring harness Mate each cable connector and press firmly to seat the contacts Ensure no wires are pinched during pedestal attachment Attach pedestal assembly using 1 4 20 tamper resistant screws and large flat washers provided A T27 wrench is included to tighten these screws firmly CABINE RUBBER BUMPER J RUBBER MOUNT SUPPORT BEAM SEAT PEDESTAL SEAT NOT SHOWN FOR CLARITY 4 20x LOCATION OF PEDESTAL ASSEMBLY MOUNTING HOLES 12 Lower and adjust each leg leveler until the pedestal section is stable and level Adjust the levelers until the bottoms of all pieces are flush and parallel with each other Inspect for binding or pinched wires then firmly tighten the fasteners to attach the two pieces together as a single unit 13
10. rectly on the glass Liquid could drip down into switch or control circuits and cause erratic game operation e Player Controls Use plastic safe non abrasive cleaners to avoid damage Apply cleaner to a clean cloth or sponge and wipe the player controls Do not apply the cleaner directly on the controls e Cabinet and Seat Use plastic safe non abrasive cleaners to avoid damage Apply cleaner to a clean cloth or sponge and wipe the seat or cabinet Do not apply cleaner directly on artwork or cabinet 8 MIDWAY AMUSEMENT GAMES LLC CHAPTER 1 OPERATION GAME FEATURES Arctic Thunder ships configured for one player game play but up to four cabinets may be linked to pro mote player competition Arctic Thunder the action packed snowmobile tour for the new millennium is a polar fantasy that trans ports adventurous trekkers across continents in search of unimaginable and ultra realistic thrills and chills From the snowy plateaus of the Himalayas and the Swiss Alps to snowscapes in Europe and the Ameri cas players can assume the role of Ponzo the resident polar primate or of Willie Qiunn a hip and cool Rastafari just to name a few Slaloming through fluffy white powder on the back of a snowmobile players and their opponents compete for power ups while launching shiver worthy snowballs and frosty power attacks STARTING UP Each time power is switched on or restored to the game machine the system enters Start up Tests Obse
11. rve software revision level is shown at the top of screen A testing message appears for approximate 60 seconds The system enters Attract Mode once it passes all power up tests The Attract Mode screen will cycle unin terrupted and display a variety of scenes and sounds from a typical race on any given track The system does not exit Attract Mode until the desired amount of coins or tokens is inserted and game play com mences GAME RULES AND OBJECTIVES The game is configured for one player game play but up to four cabinets may be linked at one time to pro mote multiple player competition To enter Game Mode individual player s must insert the required amount of currency or tokens press the Start button and select a sled and track The main objective of the game is to earn top ranking on a given track environment and or against other drivers PLAYER CONTROLS e Start Button located on the right hand side of the controller assembly is used to begin game play or to select certain features before a race Attack Button located on the left hand side of controller assembly is used during competition to punch opponents launch snowballs or power attacks Throttle Lever located on the right hand side of controller assembly is used to accelerate GAME OPERATION Access to the menu system for statistics adjustments and testing is secured by a keyed lock on the coin box to prevent tampering When the menu system is entered on screen messa
Download Pdf Manuals
Related Search