Metra Electronics 99-8219 User's Manual
Contents
1. A Using a panel removal tool carefully remove the side trim panels Figure B Remove 2 Phillips screws from radio trim panel Figure C Using panel removal tool carefully remove radio trim panel Figure D Remove 4 10mm bolts securing the radio Unplug and remove radio Continue to kit assembly mm ZZ 99 8219 je P spe DIN RADIO PROVISION WITH POCKET Note Refer also to the instructions included with the aftermarket radio 1 Slide the housing brackets onto the side of the radio housing until the clips engage Note Brackets are marked left and right Figure A 2 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward Figure B 3 Slide the aftermarket radio into the cage and secure Figure C Continue to final assembly 99 8219 ASSEMBLY ISO RADIO PROVISION WITH POCKET Note Refer also to the instructions included with the aftermarket radio 1 Slide the housing brackets onto the side of the radio housing until the clips engage Note Brackets are marked left and right Figure A 2 Mount the ISO Brackets to the aftermarket radio using the screws supplied with the radio Figure B 3 Slide the radio into the radio housing until the side clips engage Snap the Trim plate into the Radio Housing Figure C Continue to final assembly e LS RSA LS ASSEMBLY2. specifications 4 Bu 777747 Md NNI NOTES _ 99 68219 INSTRUCTIONS 1 800 221 0932 www metraonline com REV 05 13 09 COPYRIGHT 2004 2009 METRA ELECTRONICS CORPORATION INST99 8219
3. FINAL ASSEMBLY A Strip wire ends back 1 2 Twist ends together C Solder D Tape 1 Locate the factory wiring harness in the dash Metra recommends using the proper mating adapter and making connections as shown Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit 2 Re connect the negative battery terminal and test the unit for proper operation 3 Reassemble radio and dash assemblies in reverse order of disassembly FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit Metra recommends making connections as shown below Strip Splice Solder Tape Isolate and individually tape off ends of any unused wires to prevent electrical short circuit METRA EIA WIRING CODE 12V Ignition Acc Red Right Front Gray 12V Batt Memory Yellow Right Front Gray Black Ground Black Left Front White Power Antenna Blue Left Front White Black Amp Turn On Blue White Right Rear Violet Amp Ground Black White Right Rear Violet Black Illumination Orange Left Rear Green Dimmer Orange White Left Rear Green Black NOTE When a Black wire is not present ground radio to vehicle chassis All colors may not be present on all leads due to manufacturer s
4. INSTALLATION INSTRUCTIONS FOR PART 99 8219 APPLICATIONS Toyota FJ Cruiser 2007 2009 KIT FEATURES e DIN radio provision with pocket SO radio provision with pocket KIT COMPONENTS A Radio Housing Housing Brackets 0 150 Snap In Brackets Trim Plate WIRING AND ANTENNA CONNECTIONS Sold Separately Wire harness e 70 1761 Toyota 1987 up Antenna adapter e Not required TOOLS REQUIRED Phillips Screwdriver Or Panel Removal Tool SS SS 31 800 221 0932 www metraonline com COPYRIGHT 2004 2009 METRA ELECTRONICS CORPORATION m L7 NEL EN TABLE OF CONTENTS Dash Disassembly Toyota FJ Cruiser 2007 2009 rd Kit Assembly DIN Radio Provision with Pocket Z2 S0 Radio Provision with Pocket s s s s s s v s 3 Final Assembly HIHIH Note Refer also to the instructions included with the aftermarket radio KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry Log onto www installerinstitute com or call 800 354 6782 for more information and take steps toward a better tomorrow 99 8219 DASH DISASSEMBLY TOYOTA FJ CRUISER 2007 2009 Disconnect the negative battery A terminal to prevent an accidental short circuit cc Remove two Phillips screws from bottom part of side trim panels a Figure
Download Pdf Manuals
Related Search