Metra Electronics 99-7863 User's Manual
Contents
1. INSTALLATION INSTRUCTIONS FOR PART 99 7863 APPLICATIONS Honda Element 2003 up 9393 1563 KIT FEATURES DIN Head Unit Provision with pocket e 50 Head Unit Provision with pocket KIT COMPONENTS A Radio Housing B ISO Trimplate C Snap in Brackets D O E Replacement Panel WIRING AND ANTENNA CONNECTIONS Sold Separately Harness e 70 1721 Honda Acura harness 1998 up 70 7863 Element sub and AUX integration Antenna Adapter e 40 hd10 Honad Acura Antenna Adapter for Element 2005 up TOOLS REQUIRED Phillips Screwdriver 1 800 221 0932 www metraonline com COPYRIGHT 2004 2011 METRA ELECTRONICS CORPORATION 99 7863 TABLE OF CONTENTS Dash Disassembly Honda Element 2003 Up 1 Kit Assembly DIN Head Unit Provision with Pocket 2 0 Head Unit Provision with Pocket 9 Final Assembly 4 KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry Log onto www installerinstitute com or call 800 354 6782 for more information and take steps toward a better tomorrow Metra recommends MECP certified technicians I Mensa 99 7 63 das DISASSEMBLY HONDA ELEMENT 2003 UP Disconnect the negative battery terminal to preven2. rs may not be present on all leads due to manufacturer s specifications 4 m E NOTES pU 339 7863 INSTRUCTIONS 1 800 221 0932 www metraonline com REV 07 26 11 COPYRIGHT 2004 2010 METRA ELECTRONICS CORPORATION INST99 7863
3. t an accidental short circuit Unsnap and remove shift lever trim panel For manual transmis sion models untwist shift knob Figure A Unsnap and remove center dash panel Figure B eet 2 NOTE As an option the center panel the smaller piece around radio is all that needs to be removed but it is very prone to damage so full panel removal is recommended Figure C Remove 4 Phillips screws and remove radio Continue to kit assembly Figure C 99 7363 DIN HEAD UNIT PROVISION WITH POCKET 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down Figure A 2 Slide the aftermarket radio into the cage and secure Figure NOTE Models equipped with factory DDIN radio will require supplied O E replacement panel Figure C Continue to final assembly EEEEEETUES 4 99 7863 ASsemety 22 he ISO HEAD UNIT PROVISION WITH POCKET 1 Align the holes in the ISO snap In brackets with the holes in the head unit and mount the brackets to the head unit with the screws supplied with the unit Figure A 2 Slide the aftermarket head unit bracket assembly into the radio opening until the side clips engage Figure B 3 Snap the ISO trimplate over the head unit Figure B NOTE Models equipped with factory DDIN radio will require supplied O E replacement panel Figure C Con
4. tinue to final assembly 99 7863 ELT TE C 19 FINAL ASSEMBLY A Strip wire ends back 1 2 B Twist ends together C Solder D Tape 1 Locate the factory wiring harness the dash Metra recommends using the proper mating adapter and making connections as shown Isolate and individ ually tape off the ends of any unused wires to prevent electrical short circuit 2 Re connect the negative battery terminal and test the unit for proper operation 3 Reassemble in reverse order of disassembly FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit Metra recommends making connections as shown below Strip Splice Solder Tape Isolate and individually tape off ends of any unused wires to prevent electrical short circuit METRA EIA WIRING CODE 12V Ignition Red 12V Batt Memory Yellow Ground Black Power Antenna Blue Amp Blue White Amp Ground Black White Illumination Orange Dimmer Orange White Right Front Gray Right Front Gray Black Left Front White Left Front White Black Right Rear Violet Right Rear Violet Black Left Rear Green Left Rear Green Black NOTE When a Black wire is not present ground radio to vehicle chassis All colo
Download Pdf Manuals
Related Search