Meco BUSHMAN 7710.8.641 User's Manual
Contents
1. Nut NIG d DCS LA Bowl Spacer Cylinder Slide Bracket Screw M4 x 10mm 2 pcs a 2 Wing Nut M4 2 pcs eAssemble bowl to cart using 4 M6 x 45mm Screws 4 Fiber Washers 4 Spacers and 4 M6 Nuts eMake sure heat shield is resting on top of cylinder slide bracket eSecure heat shield to cylinder slide bracket using 2 M4 x 10mm Screws and Wing Nuts STEP6 Attach Control Panel Screw Nut M6 x 50mm M6 4 pcs 4 pcs eInsert valve tips on back of control panel into burner venturi Secure control panel to cart using 4 M6 x 50mm Screws and 4 M6 Nuts Confirm the valve is inserted into the burner venturi ee T weap tte Venturi STEP 7 Attach Igniter Wire eAttach Igniter Wire Push electrode connector at end of Igniter wire onto center tab on rear of Igniter Button eNOTE Be sure to route electrode wire away from hot areas of the grill STEP 8 Mounting Hood Bowl Hinges Hood Hood Hinge g Bolt Spe i M6 X 15 8 pcs Fiber Washer 8 pcs Bowl Hinge Washer Nut M6 2 pcs M6 Ka 8 pcs 8 pcs iia eInsert M6 x 15mm Bolt through Hood Hinge and Fiber Washer and into hole in back side of Grill Hood as shown Install M6 Washer and secure with M6 Nut See Photos 1 amp 2 below Repeat for remaining holes to secure two Hood Hinges eInsert M6 x 15mm Bolt through Bowl Hinge and Fiber Washer2. Always turn off the LP gas cylinder at the LP cylinder valve when not in use Allow the grill to cool before handling parts or cleaning Do not move an LP gas grill when in use or hot Never touch hot surfaces Use heat resistant gloves long handled tongs or cooking mitts at all times since grill will become very hot Do not wear loose clothing for example hanging shirt tails clothing with frills etc around a LP gas grill while in use or hot Never lean your body over the LP gas grill when lighting it or while it is in use or hot Never douse the grill with water when its surfaces are hot because it may cause grease to splatter or the porcelain cooking grids and hood to break Regularly clean your LP gas grill between uses and espe cially after extended periods of storage Ensure the grill and its components are cool before cleaning In order to extend the life and maintain the condition of your grill we strongly recommend that the unit be covered when stored outside for any length of time especially during the winter months CARE AND MAINTENANCE AA WARNING Check the LP gas grill for gas leaks and Burner obstructions before each use Always turn off the LP gas cylinder at the LP cylinder valve when not in use Allow grill to cool before handling parts or cleaning Most residue on the Cooking Grids can be cleaned with a baking soda and water solution For stubborn s
3. bubbles appear on any of the connection points then you have detected a gas leak Immediately close the LP cylinder valve by turning the handle clockwise A If leak appears at either end of hose and regulator assembly retighten the connection at the leak but do not overtighten Note Only hand tighten at coupling nut Repeat Leak Test B If the leak is coming from the LP gas cylinder from the valves at the control knobs or if the leak cannot be stopped do not use the grill Call Customer Service at 1 800 251 7558 11 Turn all control Knobs to the off position and turn the handle on the LP gas cylinder clockwise until it stops Disconnect LP gas cylinder by turning coupling nut on regulator in a counter clockwise direction until regulator is released from threaded LP cylinder gas nozzle 12 Place the protective cap over LP cylinder gas nozzle Always perform a leak test before each use Leak test must be performed in a well ventilated area Never perform a leak test on a grill while in use or hot If you detect a gas leak that cannot be corrected by using the leak test procedures below do not use the LP gas grill Never smoke or have an open flame near the grill during a leak test LP Gas Cylinder Control Valve OPERATING THE LP GAS GRILL Before proceeding make certain that you understand the Important Safeguards on pages 2 Regulator through 4 of this manual Coupling
4. may be hazardous and should be checked by a liquid propane supplier The LP gas cylinder should never be filled more than 80 of cylinder volume 20 lb maximum Do not ask the propane supplier to over fill the cylinder If you obtain LP gas through a cylinder exchange dealer make sure you are getting a safe and adequate O P D cylinder Use only a licensed LP gas cylinder dealer Keep children away from LP gas cylinder at all times Do not use store or transport the LP gas cylinder where it would be exposed to high temperatures The relief valve may open which will allow a large amount of flammable gas to escape Never leave an LP gas cylinder inside a vehicle which may become overheated by the sun WARNING Never store an LP cylinder indoors Storage of an outdoor cooking gas appliance indoors is permissible only if the cylinder is disconnected and removed from the outdoor cooking gas appliance Cylinders must be stored outdoors out of the reach of children and must not be stored in a building garage or any other enclosed area WARNING Never store a spare LP gas cylinder under or near the grill All spare and disconnected LP gas cylinders must have safety caps installed on the LP cylinder valve LP gas is not natural gas The conversion or attempted use of natural gas in an LP unit or LP gas in a natural gas unit is dangerous and will void your warranty Never attempt to repair an LP gas cylinder valv
5. 4 pcs 4 pcs eAssemble Rear Brace to wheel leg and fixed leg using 4 M6 x 35mm Screws and 4 M6 Nuts Assemble the 2 Cart Braces to the wheel leg and fixed leg using 4 M6 x 50 mm Screws Rear Brace Cart Brace STEP 4 Attach Flavor Activator Pins Grease Cup Hanger Burner amp Heat Shield Follow the steps in order below Refer to the step numbers below and beside the images 1 Assemble 2 flavor activator Mounting Studs and two Fiber Washers to the bowl using 2 M6 nuts 2 Insert Grease Cup Hanger into bowl 3 Insert Burner Venturi tubes down through holes in bottom of grill bowl toward front of grill Also insert igniter wire through hole in bottom of bowl From underside of bowl insert 2 ST 4 0 x 10mm screws into burner mounting holes and tighten 4 Thread grease cup holder through center hole of heat shield and secure heat shield to bottom of bowl as shown using 1 ST 4 0 x 10mm Screw The shield will later be secured to the cylinder slide bracket on the cart Mounting Grease Cup Hanger Stud M6 2 pcs Fiber Washer 2 pcs Nut M6 2 pcs 2 Inside of Bowl Screw ST 4 0 x 10mm 3 pcs Note orientation of venturi tubes to Heat Shield Install Heat Shield toward left side tank side of Body STEP 5 Attach Bowl to Cart Pai IW DD D HHDH aD TRAE ALLL DH Screw M6 x 45mm 4 pcs Heat Shield Fiber Washer 4 pcs Bowl Spacer 4 pcs Fiber Washer
6. LP cylinder valve Once fire is out and grill has cooled off Clean residual food particles and excess grease from inside firebox area grease cup and other surfaces If you can safely reach the control panel turn control knobs to OFF then close LP cylinder valve Clean burner and venturi tubes See How To Clean Burners Section Troubleshooting Problem Possible Cause Solution Burners will not light using the ignitor Burners not assembled correctly Not pausing long enough before clicking the Ignitor Button No spark electrode cracked broken or loose LP gas cylinder is empty Regulator Coupling nut is not fully connected to LP cylinder See re assembly after cleaning in Care and Maintenance When lighting the Burner push in and turn control panel knob counter clockwise to the high position Pause 4 seconds then Push in Ignitor button several times so that it clicks each time 1 Make sure all the wires are connected and to the right terminals 2 lf Electronic check the battery Make sure it is pushed in the holder 3 Gas collector tab is bent making too large or small of a gap between electrode and tab By hand bend gas collector tab back within a maximum of 3 16 gap to electrode Page 26 4 Tighten Electrode mounting screws 5 Replace damaged electrodes Take LP gas cylinder to licensed LP gas supplier to be refilled Tighten coupling nut by hand about one half to three quarte
7. Nut Before lighting the LP gas grill you must open the the hood to prevent an explosion from Supplies Needed for a Leak Test gas build up Clean paint brush water and dishwashing liquid If your LP gas grill catches on fire How to perform a leak test See illustration above for If the fire is in the grill portion and you can safely more information reach the control knobs on the control panel then AWARNING Never use an open flame to test for gas turn them to the off position leaks If the fire involves one of the hoses and you can 1 Use an LP Cylinder equipped with an OPD Overfill safely reach the LP cylinder valve shut the valve Prevention Device and have it filled at an authorized LP off gas dealer by a qualified attendant If the fire involves the cylinder leave it alone 2 Make sure all of the grill control panel knobs are turned to evacuate the area and call the fire department the off position and verify that the LP gas cylinder valve If there is any type of fire that threatens either is closed by turning the knob on the LP gas cylinder personal safety or endangers property call the clockwise until it stops fire department 3 Remove the protective cap from the LP cylinder gas If you notice grease or other hot material dripping nozzle from the grill onto the valve hose or regulator turn 4 Hold regulator in a straight line with LP cylinder gas off the gas supply immediately After the grill has nozzle so the con
8. and Cooking Grid according to Assembly Instructions Always turn off the LP gas cylinder at the LP Check your LP gas grill for gas leaks deterioration proper cylinder valve when not in use Allow grill to cool assembly and burner obstructions before using the grill before handling parts or cleaning after periods of storage and or non use i e over winter 22 Parts Diagram Some small parts may not be depicted 11 Cylinder Heat Shield 12 Rear Brace 13 Wheel Le 14 Grease Cup amp Hanger 15 Fixed Leg with caps 16 Side Table 17 Control Panl 1 18 Valve Hose Regulator Assm 1 19 Control Knob 2 20 Piezolgniter 1 21 Cylinder Slide Bracket 1 22 Cylinder Slide Lock 1 23 Wheel gt gt 2 24 AxlePin gt 2 25 Cotter Pin 2 26 Cylinder Support 1 l R T Cart Brace 1 7 ma 28 Cylinder Block Wire art Brace T 30 Leg Cap 2 10 31 Privacy Panel 1 Bowl Spacer M6 4 Screw M4 x 10mm 2 Wing Nut M4 2 Clevis Pin 6mm x 32mm 2 4 2 8 HARDWARE LIST 4 PARTS LIST Description Qty Key Description Qty Screw M6 x 15mm 12 1 Hood 1 Wing Bolt M6 x 10mm 2 2 Handle Shield 1 Screw M6 x 50mm 10 2 3 Hood Handle 1 Screw ST 4 0 x 15mm 2 4 Warming Rack 1 Screw M6 x 35mm 4 5 Cookin Grid 1 Nut M6 30 6 Flavor Activator 1 Mounting Stud M6 2 L Main Burner 1 Screw Gi 4 0 10mm 8 8 Electrode Collector Assm 1 Screw M6 x 45mm 12 9 Hood Hinge Assm 2 Fiber Washer MG 14 10 Bowl 1 1 1 1 Cotter Pin 1 6mm x 28mm Screwt M5
9. and into hole in back side of Grill Bowl as shown Install M6 Washer and secure with M6 Nut See Photos 3 amp 4 below Repeat for remaining holes to secure two Bowl Hinges NOTE DO NOT Overtighten mounting screws You could crack the porcelain grill coating Photo 1 Fiber Washers go Photo 2 between hinge and Bowl or Hood Bowl Hinge Photo 3 STEP 9 Attach Hood p ee OA oa zi 2 pcs 2 pes eAlign Hood Hinge tabs with Bottom Hinge tabs and insert Hinge Pins from outside Secure each Hinge Pin with Cotter Pin as shown Close Hood and check assembly to make sure that the hood and bowl fit properly together Adjust hood by loosening the Hinge Bolts and retightening 11 44 CAUTION To reduce the risk of a laceration hazard wear protective gloves when handling parts that have sharp edges STEP 10 Attach Hood Handle amp Handle Shield Hood Y s Handle K 1 pc Hood M5 X 10 Shield 2 pcs 1Pc Bolt eInsert M5 x 10mm Bolt through Handle Shield then through inside of Hood into Hood Handle Repeat for other side of handle NOTE DO NOT Overtighten mounting screws You could crack the porcelain grill coating Step 11 Insert Flavor Activator Note Place protrusions Place Flavor Activator onto Flavor toward hood Activator Mounting Studs STEP 12 Insert Cooking Grid Step 13 Insert Warming Rack ePlace Cooking Grid onto ledge in bowl Position warming rack a
10. explosion from gas build up the off position and close the valve on the LP cylinder Always inspect the gas hose and regulator Wait five minutes and repeat all of the above manual assembly before each use If the hose is cut lighting procedures If the grill still fails to light see damaged or showing signs of excessive abrasion the Troubleshooting page or wear do not use the LP gas grill Contact the manufacturer as the hose must be replaced with 5 Check to make sure that the burner is lit an assembly specified by the manufacturer prior 6 Light the remaining half of the burner by turning the control to further use of the LP gas grill knob counter clockwise Your grill has a crossover ignition system that allows the burner to light each side successively How to manually light your LP gas grill 7 If burner does not light repeat Step 3 The burner 1 Open Hood should light within three or four attempts 8 After ignition preheat the grill by turning the control knobs to High for 3 5 minutes The grill should be pre heated before every cooking session The hood should be closed during preheating 2 Important Make sure Control Knobs are turned off Open the LP gas cylinder valve by turning counter clockwise until it stops 3 Insert a lit match through match lighting hole underneath the grill bowl on the right side See figure below A WARNING If the burner goes out during the cooking cycle turn the cont
11. in serious bodily injury or property loss Use only the hose and regulator assembly that has been furnished with this LP gas grill If the hose and regulator assembly is not working properly and you need a replacement contact the manufacturer 1 800 251 7558 Inspect the hose before each use If the hose is cut or damaged or shows signs of excessive abrasion or wear do not use the LP gas grill Contact the manufacturer as the hose must be replaced with an assembly specified by the manufacturer prior to the further use of the LP gas grill LP Cylinder Read and follow all warnings on LP gas cylinder If you see smell or hear the hiss of LP gas escaping from the cylinder 1 Evacuate all people from the grilling area 2 Do not attempt to correct the problem yourself 3 Call the local fire department The LP gas cylinder for use with the Aussie LP gas grills must meet the following requirements 1 12 diameter x 18 tall 20 lb maximum capacity 2 Overfill Prevention Device OPD safety feature should be noted on cylinder 3 Must be constructed and marked in accordance with the U S Department of Transportation DOT or the National Standard of Canada CAN CSA B339 See collar for marking 4 Must have collar to protect LP cylinder valve Never use an LP gas cylinder if it shows signs of dents gouges bulges fire damage corrosion leakage excessive rust or other forms of visual external damage it
12. the pan Never use the grill without Grease Cup in place 9 A WARNING If you notice grease or other hot material dripping from the grill onto valve hose or regulator turn off gas supply immediately After the grill has cooled determine the cause and correct it After cleaning the valve hose and regulator perform a leak test before continuing use See Before Using Your LP Gas Grill section page 16 of this manual for correct leak test procedures 10 This installation must conform with local codes or in the absence of local codes with either the National Fuel Gas Code ANSI 2223 1 or CAN CGA B149 2 Propane Installation Code 11 If an external electrical source is utilized the outdoor cooking appliance when installed must be electrically grounded in accordance with local codes or in the absence of local codes with the National Electrical Codes ANSI NFPA 70 or the Canadian Electrical Code CSA C22 1 12 Keep any electrical supply cord and the fuel supply hose away from any heated surfaces Electric cords should be placed away from walkways to avoid a tripping hazard 13 Combustible materials should never be within 36 in of the back or sides of your LP gas grill WARNING Always Store Lp Cylinders upright and where temperatures do not exceed 125 degrees Fahrenheit Never store a spare or disconnected LP cylinder under or near this LP gas grill 14 17 Check the LP gas grill for gas leaks and burner obstruct
13. Verify that there are no insects or to Clean your Burners Section to remove any possible insect nests blocking the inlet hole Normal wear and obstructions corrosion may enlarge some holes however if large cracks or holes are found the Burner should be replaced ae Sa Note It is normal for surface rust to be present on the Burner 6 If grill is to be stored coat Burner lightly with cooking oil K and Wrap in a protective cover to keep insects out A 7 After cleaning reinstall Burner and other parts removed back into grill Note When refitting the Burner be careful to check that it is positioned correctly Refer to Step 4 of Assembly Instructions for reinstallation Venturi Tube Spider Webs or Nest Inside Venturi Tube Spiders or small insects can build nests webs and lay eggs in the grills venturi tubes obstructing the flow of gas to the burner The backed up gas can ignite behind the control panel causing damage to the grill and even injury to the operator This is Known as a flashback In order to prevent flashbacks the burner s should be removed from the grill and cleaned periodically especially if the grill has been stored for an extended period of time 21 How to Clean the Grill Body Adjust Gas Collector tab as shown below to obtain 3 16 gap 1 Remove Cooking Grid Flavor Activator and Burner between electrode tip and collector tab before full cleaning 2 Remove excess grease and
14. a Aussie meco Outdoor Living Bushman LP Gag Grill Assembly and Use Manual for Bushmar Deluxe Bushman Deluxe For use with models 7710 8 641 FOR OUTDOOR HOUSEHOLD USE ONLY NOT FOR COMMERCIAL USE 7710S58 641 For Customer Service call 1 800 251 7558 or visit our web site at www aussiegrills com e Failure to follow these instructions could result in fire or explosion which could cause death serious personal injury or property damage s Read and follow instructions carefully before assembly or use e Do not use this product for any other purpose than which it is intended e These instructions must be kept with the user SAVE THESE INSTRUCTIONS DANGER If you smell gas 1 Do not store or use gasoline or other 1 Shut off gas to the appliance flammable liquids or vapors in the vicinity 2 Extinguish any open flame of this or any other appliance 3 Open lid 2 An LP cylinder not connected for use shall 4 If odor continues keep away from the not be stored in the vicinity of this or any appliance and immediately call your gas other appliance supplier or your fire department l IMPORTANT SAFEGUARDS eee Il Assembly INSUUCUONS veuiidicsictderstasistawasedidiecduniacstaeinwrdsauaanaaes Step 1 Assemble Wheel Led Step 2 Assemble Fixed Leg Step 3 Assemble Cart Step Burner amp Heat Shield Step 5 Attach Bowl to Cart Step 6 Attach Control Panel eee Step 7 A
15. act ly a fire causing death or serious injury may occur CARBON MONOXIDE HAZARD This appliance can produce carbon monoxide which has no odor 36 Even though your LP cylinder may appear to be empty gas may still be present and the cylinder should be transported and stored accordingly 44 DANGER Using it in an enclosed space can kill you Never use this appliance in an enclosed space such as a camper tent car or home ASSEMBLY INSTRUCTIONS PREPARATION FOR ASSEMBLY Remove Grill and all the packaging from carton and place on floor Make sure there are no loose parts Note Before using your grill read the instructions and your manual For easier set up and assem bly follow instructions of each step in the order they are written as you look at the diagrams If accessories mentioned in certain assembly steps do not come with your model skip that step and proceed to the next step that applies to your model To reduce the risk of serious bodily injury or death The use of alcohol prescription or non prescription drugs could impair the consumer s ability to properly assemble or safely operate this appliance Do not connect LP cylinders until assembly is com plete NOTICE MECO Corporation strives to be a quality supplier of consumer products If we ommitted any parts needed for assembly or you need troubleshooting information please contact us using our toll free number or visit our
16. als should never be used or stored within 36 inches of the back or sides of your LP gas grill Locate your LP gas grill at least 10 feet away from your house or any building Do not use the grill in a garage breezeway carport porch or under a surface that can catch fire 6 of this manual pages 2 through 4 Make sure you follow and understand all instructions and warnings If you have any questions regarding these pages call 1 800 251 7558 and ask for a Customer Service Representative This installation must conform with local codes or in the absence of local codes with either the National Fuel Gas Code ANSI 2223 1 or CAN CGA B149 2 Propane Installation Code If an external electrical source is utilized the outdoor cooking appliance when installed must be electrically grounded in accordance with local codes or in the absence of local codes with the National Electrical Codes ANSI NFPA 70 or the Canadian Electrical Code CSA C22 1 If any electric appliance or rotisserie is used with the LP gas grill do not allow cords to touch or be near hot surfaces Electric cords should be placed away from walkways to avoid a tripping hazard Grill storage cover must be removed and placed at least 36 inches from the LP gas grill while in use The grill cover is made of a flammable material The grill must be completely cooled before putting the cover back on the grill Never store a spare or disc
17. e cylinder manufacturer has not resolved the issue to your satisfaction then call MECO Corporation at the customer service number listed below MECO Corporation requires proof of purchase and we suggest you keep your receipt Damages caused by commercial or institutional use accidental or intentional damage repairs made or attempted by unauthorized persons or misuse are not covered by this warranty If defective the part or product will be repaired or replaced at the option of MECO Corporation without charge This warranty does not include the cost of any inconvenience or property damage due to failure of the product and does not cover damage due to misuse abuse accident damage arising out of transporta tion of the product damage incurred through commercial use or failure to perform normal and routine maintenance LIABILITY FOR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGES ARE EXPRESSLY EXCLUDED BY THIS WARRANTY ANY APPLICABLE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS ARE LIMITED IN DURATION TO THE PERIOD COVERAGE OF THIS EXPRESS WRITTEN LIMITED WARRANTY Some states do not allow limitation on how long an implied warranty lasts so this limitation may not apply to you Deterioration or damage due to severe weather conditions such as hail hurricanes earthquakes or tor nados discoloration due to exposure to chemicals either directly or in the atmosphere is not covered by this limited warranty No returns will be accepted without
18. e yourself See an authorized LP gas cylinder dealer for repairs When transporting an LP gas cylinder keep it secured in an upright position with cylinder valve turned to off position Connecting Disconnecting LP Gas Cylinder to Grill Do not operate the LP gas grill when the LP gas cylinder is not attached to the cart as shown in the Assembly Instructions Always check for gas leaks when you disconnect and reconnect the regulator to the LP gas cylinder especially after a period of storage for example over winter Check tubes that lead into the burner for any blockage from insects spiders or food grease before using Check grill hoses for cracking brittleness holes or leaks Make sure there are no sharp bends in the hose or tubing Make sure Regulator Hose does not contact hot metal surfaces Never connect or disconnect LP gas cylinder or fittings while grill is in use or is hot When the LP gas cylinder is connected the grill must be kept outside in a well ventilated space Turn off all Carefully read the Important Safeguards section of the grill control knobs and the LP cylinder valve when grill is not in use Move gas hose as far away as possible from hot surfaces Place dust cap on cylinder valve outlet whenever the cylinder is not in use Only install the type of dust cap on the cylinder valve outlet that is provided with the cylinder valve Other types of caps or plugs ma
19. grill H Preparation Before Cooking Wash the porcelain or chrome coated Cooking Grids with a mixture of hot water and baking soda Empty the grease cup after each cooking session so excessive grease does not accumulate Failure to remove grease may result in grease dripping onto the cart and or a grease fire in the tray Lighting the Grill Using Igniter N Open Hood before lighting the grill to prevent an explosion from gas buildup PE A SOENT gga 4 Push in Igniter to light gt gt Always inspect the gas hose and regulator assembly before each use If the hose is cut damaged or shows signs of excessive abrasion or wear do not use the LP gas grill Contact the manufacturer as the hose and regulator assembly must be replaced with an assembly specified by the manufacturer prior to further use of the LP gas grill ow to light your LP gas grill See illustrations below 1 Open Hood 2 Important Make sure control knobs are turned off first Open the LP gas cylinder valve by turning the valve handle counter clockwise until it stops 3 From the Off position push control knob in on the left side and turn counter clockwise to the high position 4 Push the igniter button several times so that it clicks each time 5 Check to make sure that the burner is lit 6 Light the remaining half of the burner by turning the control knob counter clockwise Your grill has a cross
20. grill Never leave grill unattended during use or cleaning Never allow children to operate or play near an LP gas grill Keep animals and bystanders out of the grill area Always turn off the LP gas cylinder at the cylinder valve when not in use Allow grill to cool before handling parts or cleaning A WARNING Do not move an LP gas grill when in use or hot A WARNING Never touch hot surfaces Use heat resistant gloves long handled tongs or cooking mitts at all times The grill will become very hot Open the hood carefully when cooking to avoid burns from the hot air and steam trapped inside Use only the hose and regulator assembly that is supplied with your LP gas grill and or specified by the manufacturer 30 Use of this LP gas grill other than for the intended use 37 Never store an LP gas cylinder indoors empty or filled or alteration of LP gas grill in any way may not be safe If storing the gas grill indoors disconnect LP gas cylinder and will void any warranty and store it outdoors out of the reach of children 31 Never attempt to repair the LP gas grill or cylinder 38 Never leave an LP cylinder inside a vehicle which may yourself Contact the manufacturer for information become overheated by the sun regarding repairs to your grill 39 Never lean your body over the LP gas grill when lighting 32 LP gas is not natural gas The conversion or attempted it or while it is in use or hot use of natural gas in an LP u
21. grilling Turn control knobs off and turn handle of LP cylinder clock wise until it stops Open hood carefully and let fire burn out After the grill cools remove and clean all parts The worn nozzles don t have enough bite to engage the valve Try another licensed LP dealer 25 TROUBLESHOOTING Cont d H f Outside temperature humidity Although this sound may be alarming this is NOT dangerous umming or i i n i s histling from the barometric pressure and the as long as it is not accompanied by the smell of gas Simply reg lato gas level within the tank may adjust the burner settings and usually the sound will subside u cause the rubber diaphragm If the humming sound persists a change in atmospheric inside the regulator to vibrate conditions will eventually stop the vibration Should you smell making a humming or gas do not use the grill and call Customer Service at whistling sound 1 800 251 7558 If your problem is not resolved from the information provided above please call Customer Service at 1 800 251 7558 If you need a replacement part under warranty a proof of purchase and your model serial number will be necessary IMPORTANT NOTICE This Gas Grill must be used with a LP Gas Cylinder equipped with an OPD Overfill Prevention Device This is a secondary device to prevent the overfill of your LP Gas cylinder The proper methods for the filling of your LP Gas cylinder are by weight or volume a
22. in meat Grease trapped around burner system Some dealers have older fill nozzles with worn threads Reconnect the wire Replace ignitor wire electrode assembly Call the Customer Service Department See re assembly after cleaning in Care and Maintenance Take LP gas cylinder to licensed LP gas supplier to be refilled Turn control knobs to off position and turn LP gas cylinder handle clockwise until it stops Wait five minutes Relight LP gas grill If flame continues to be low turn off gas at cylinder and grill Disconnect the regulator from the LP gas cylinder Reconnect the regulator to the LP gas cylinder Perform a leak test Relight grill This will reset the excess flow valve Tighten coupling nut by hand about one half to three quarters turn Do not use tools See How to Clean the Burners in Care and Maintenance Check LP gas cylinder Refill if necessary Turn control knobs to off position and turn LP gas cylinder handle clockwise until it stops Wait five minutes Relight LP gas grill If flame continues to be low turn off gas at cylinder and grill Disconnect the regulator from the LP gas cylinder Reconnect the regulator to the LP gas cylinder Perform a leak test Relight grill This will reset the excess flow valve Turn front of grill away from wind or increase flame height Check LP gas cylinder Refill if necessary See Low flame problem above Clean grill Trim fat from meat before
23. ions before each use WARNING Do not use a flame to check for gas leaks See Before Using Your LP Gas Grill section of this manual for correct leak test procedures A clogged burner tube can lead to a fire beneath grill 18 A DANGER If you see smell or hear the hiss of 20 21 22 23 24 Zo 26 Zi 28 29 escaping gas from the LP cylinder A Get away from the cylinder B Do not attempt to correct the problem yourself C Call your local fire department _A WARNING Do not operate an LP gas grill if you have knowledge of or suspect a gas leak Always inspect the gas hose and regulator assembly before each use Always turn the LP cylinder to the Off position before inspecting parts If the hose is cut damaged or showing signs of excessive abrasion or wear do not use the LP gas grill Contact the manufacturer as the hose must be replaced with an assembly specified by the manufacturer prior to further use of the LP gas grill A WARNING Before lighting the LP gas grill open the hood to prevent an explosion from gas build up See Operation of Your LP Gas Grill section If burner does not light turn off all gas control knobs Leave the grill hood open and wait five minutes before attempting to light If burner goes out during operation turn off all gas control knobs Open the hood and wait five minutes before attempting to light Exercise reasonable care when using this LP gas
24. nection does not cross thread cooled determine the cause and correct it After 5 Insert nipple of regulator into the LP cylinder nozzle cleaning the valve and hose and regulator assembly opening perform a leak test before continuing use 6 Hand tighten coupling nut in a clockwise direction Do not Do not operate an LP gas grill if you have knowledge use tools of or suspect a gas leak 7 Mix one cup of water with one cup of dishwashing liquid Never allow children to operate or play near an LP gas 8 Open the valve on LP gas cylinder Turn the knob on the grill Do not leave grill unattended LP gas cylinder counter clockwise 17 kh WARNING Continued Never touch hot surfaces Use heat resistant gloves long handled tongs or cooking mitts at all times since the grill will become very hot Open the hood carefully when cooking to avoid from the hot air and steam trapped inside Always turn off the LP gas cylinder at the LP cylinder valve when not in use Allow grill to cool before handling parts or cleaning Do not move an LP gas grill when in use or hot Do not wear loose clothing example hanging shirt tails clothing with frills etc around a LP gas grill while in use or hot Never lean your body over the LP gas grill when lighting it or while it is in use or hot This LP gas grill is not designed to be used with a solid plate griddle Full coverage of plates will cause excessive heat and could damage the
25. nit or LP gas in a natural gas unit is dangerous and will void your warranty 40 Do not attempt to disconnect move or alter any gas fittings while your LP gas grill is in operation 33 Do not use charcoal in an LP gas grill Do not use aerosols or store flammable liquids or materials near this 41 Your LP gas grill should be cleaned on a regular basis LP gas grill Refer to Care and Maintenance section in this manual 42 This LP gas grill is not designed to be used with a solid plate griddle Full coverage of plates will cause excessive heat and could damage the grill 34 AA WARNING Do not wear loose clothing for example hanging shirt tails clothing with frills etc around an LP gas grill while in use or hot 43 Never douse the grill with water when its surfaces are hot because it may cause grease to splatter or the porcelain cooking grids and hood to break 35 Never use an LP cylinder if it shows signs of dents gouges bulges fire damage corrosion leakage excessive rust or other forms of visual external damage it may be hazardous and should be checked by a Liquefied Petroleum supplier Do not use an LP cylinder with a damaged valve K 4 When not in use the LP cylinder valve must be turned to Off position 45 a Do not store a spare LP gas cylinder under or near this appliance b Never fill the cylinder beyond 80 percent full and c If the information in a and b is not followed ex
26. onnected LP gas cylinder under or near this LP gas grill Inspect the hose and regulator assembly before each use If the hose is cut or damaged or shows signs of excessive abrasion or wear do not use the LP gas grill Contact the manufacturer as the hose must be replaced with an assembly specified by the manufacturer prior to the further use of the LP gas grill Use only the hose and regulator assembly that is supplied with your LP gas grill Use of this LP gas grill other than for the intended use or alteration of the LP gas grill in any way may not be safe and will void any warranty LP gas is not natural gas The conversion or attempted use of natural gas in an LP unit is dangerous and will void your warranty Never use an LP gas cylinder if it shows signs of dents gouges bulges fire damage corrosion leakage excessive rust or other forms of visual external damage it may be hazardous and should be checked by a Liquefied Petroleum supplier Do not use an LP cylinder with a damaged valve Never use charcoal in your LP gas grill Do not use aerosols or store flammable liquids or materials near this gas grill Leak Testing 9 Check for leaks by brushing the soap solution on all LP gas connections and fittings such as those shown by the heavy arrows in the diagram below Make sure you generously brush the locations with the soap solution completely surrounding the connections and fittings 10 If growing
27. or fat from the grill Bowl with a soft plastic or wooden scraper Never use steel wool or other abrasive cleaning product on porcelain coated surfaces 3 For further cleaning use hot soapy water and a cloth or nylon bristled brush only Do not immerse the gas controls or manifold in water Make sure all water is removed from Burner Gas Collector Pa A 4 When finished cleaning replace Burner Flavor Electrode Box 3 16 GAP Activator and Cooking Grid according to Steps 4 11 and 12 in the Assembly Instructions 5 Check burner operation after reassembly If no spark pinch together or open Gas Collector Tab to adjust 3 16 gap between electrode tip and edge of Gas Collector Tab Always turn off the LP gas cylinder at the LP cylinder valve when not in use Allow grill to cool before handling parts or cleaning Do not use aerosols or store flammable liquids or materials near this gas grill Preventive Maintenance Periodically check and tighten all nuts bolts and screws Remove and wash the Flavor Activator in order to keep it clean Burning off the residue after each cooking will make A WARNING cleaning easier Clean with soap and water Never store an LP gas cylinder indoors empty or filled If storing the gas grill indoors disconnect the LP gas cylinder and store it outdoors out of the reach of children Never leave an LP gas cylinder inside a vehicle which may become overheated by the
28. over ignition system that allows the burner to light each side successively 7 If burners does not light repeat Step 3 The burner should light within three or four attempts If burner still does not light try the right side fA WARNING If both sides of the burner fail to light after following Steps 3 amp 4 turn all knobs to the off position and close the valve on the LP gas cylinder Wait five minutes then repeat all of the above lighting procedures Note If the burner still fails to light refer to the Troubleshooting page The burner can be lit manually see Manual Lighting of the Grill After ignition preheat the grill by turning the control knobs to High for 3 5 minutes The grill should be pre heated before every cooking session The hood should be closed during preheating A WARNING If a burner goes out during the cooking cycle turn all knobs to the off position and close the valve on the LP cylinder Open hood and wait five minutes before attempting to relight the grill 2 Turn LP cylinder handle counter clockwise to open 3 Push in left or right control knob and turn counter clockwise to the High position 18 Manual Lighting of the Grill 4 Push in and turn the right main burner control knob counter clockwise to the high position A WARNING If the burner fails to ignite after Open Hood before lighting the grill to prevent an following the above procedure turn control knob to
29. prior authorization from MECO Corporation Authorization for return may be obtained by calling 1 800 251 7558 Handling and transportation costs for returning the product are not covered by this warranty and will be paid for by the purchaser Please send your correspon dence to MECO Corporation 1500 Industrial Road Greeneville TN 37745 serial No Please use this number in registering your warranty and any correspondence with MECO Corporation P N 03 6907 10 REV 20090114 For reference and correspondence record your Serial number here See nameplate on grill 28
30. r burner opening You should follow the Burner Maintenance section of this manual for cleaning the burners Grill Cooking The burner heats up the Flavor Activator underneath the grid which in turn heats the food on the grill The natural food juices produced during cooking fall onto the hot Flavor Activator below and vaporize The subsequent rising smoke bastes the food as it travels upwards giving it that unique barbecued flavor Roasting Hood Cooking The grill is equipped with a roasting hood giving the option of cooking with hood closed to form an oven for roasting food such as roasts of meat whole chickens etc When the hood is closed a large amount of heat is trapped inside the grill Thus it is IMPORTANT to make sure that the burner is turned to the low position to prevent burning of the food Avoid lifting the hood unnecessarily as heat is lost every time the hood is opened CARE AND MAINTENANCE How to turn off your LP gas grill 1 When you have finished using your grill turn the grill Control Knobs clockwise to the Off position 2 Turn off the gas at the LP cylinder valve by turning the handle clockwise until it stops 3 Wait until the grill is cool before closing the grill hood and putting on the cover WARNING Never store an LP gas cylinder indoors empty or filled If storing the gas grill indoors disconnect LP gas cylinder and store it outdoors out of the reach of children
31. rol knob to the off position and close the valve on the LP cylinder Wait five minutes before attempting to relight 1 Open hood 2 Turn LP cylinder handle counter clockwise until it stops 3 Match lighting hole in right side of grill body Insert a lit match through the match lighting hole 4 Push in right control knob and turn counter clockwise to the High position NOTE Shown with right side table removed for clarity 19 Your burner has been preset by the manufacturer for opti mal flame performance A blue flame possibly with a small Never leave your LP gas grill unattended during use or cleaning yellow tip is the result of the optimal air and LP gas mix ture See diagram below After each cooking session close the hood and turn the grill burners to the high position and burn for five minutes Check Your Flame End of Cooking Session Yellow Tip Primarily Blue Flame O This procedure will burn off cooking residue thus making cleaning easier The flame should be checked before the initial cooking ses Turn off Your LP Gas Grill sion and periodically throughout the grilling season espe cially after storing the grill over a long period of time If the flame is significantly yellow in color the amount of LP gas in the air LP gas mixture is not correct This could be a result of a blocked burner from grease drippings or from insects building a nest inside the burner o
32. rs additional turn Do not use tools 24 TROUBLESHOOTING Cont d Problem Burners will not light using the ignitor Burners will not light using a match Low flame or low heat OR Flames blow out Flare up Persistent grease fire Unable to fill LP tank Possible Cause LP Excess flow valve tripped in regulator Vapor lock in connections Obstructions in burners Wet Electrodes and burners Solution Turn control knobs to off position and turn LP gas cylinder handle clockwise until it stops Wait five minutes Relight LP gas grill If flame continues to be low turn off gas at cylinder and grill Disconnect the regulator from the LP gas cylinder Reconnect the regulator to the LP gas cylinder Perform a leak test Relight grill This will reset the excess flow valve Clean the burners See How to Clean the burners in Care and Maintenance Dry electrode with clean cloth Air dry or use blow dryer Wire loose or disconnected Wire shorting sparking between ignitor and electrode Burners not assembled correctly LP gas cylinder is empty LP Excess flow valve tripped in regulator Regulator Coupling nut is not fully connected to LP cylinder Obstructions in burners LP Gas in LP cylinder is low Natural Gas supply pressure is low Excess flow valve tripped in regulator High or gusting winds Gas in LP cylinder is low Excess flow valve tripped Grease build up Excessive fat
33. s described in NFPA 58 Please make sure your filling station fills your LP Gas cylinder by weight or volume Ask your filling station to read purging and filling instructions on the LP cylinder before attempting to fill Raises up while filling then stops when full Rises up while filling then stops when full Do not exchange the LP Gas cylinder unless the exchange LP cylinder is equipped with an OPD Otherwise you will lose the OPD Overfill Prevention Device feature If there is not an LP cylinder available for exchange equipped with an OPD we recommend that you have your cylinder filled at an authorized LP gas dealer by a qualified attendant 26 This page intentionally left blank 27 MECO CORPORATION LIMITED WARRANTY This product is warranted to the original consumer purchaser against defects in material and workman ship under normal outdoor household use and correct assembly if assembled by the consumer pur chaser This grill is warranted for a period of one 1 year from the date of purchase MECO Corporation DOES NOT warrant in any way the propane cylinder see label on cylinder for cylinder manufacturer s warranty The LP cylinder manufacturer is responsible for the materials workmanship and performance of the cylinder If the cylinder has a defect malfunctions or you have a question regarding the cylinder call the cylinder manufacturer s customer service center The phone number is on the cylinder If th
34. s 20 1 Porcelain Coated Cooking Surfaces see 21 2 Spider Alert 21 3 Burner Maintenance eee ee ee 21 4 Flavor PCUV ALON soisccieints ci ctentisntinncsadceizeencdssetsaenbdsels 22 SFDI CUD eee een E eee A eee ence ene 22 6 Cleaning the Grill Body sss see 22 7 Preventive Maintenance ee ee ee e 22 8 Storage ee eee ny ee eee ner eee eee ener 22 IV Farts eles 23 Parts List amp Hardware SL 23 V Emergencies amp Troubleshooting sees ee eee 24 VI Important Notice LP Cylinder with OPD 26 VII Limited Warranty sese eee eee 28 IMPORTANT SAFEGUARDS FAILURE TO FOLLOW THESE SAFEGUARDS COULD RESULT IN DEATH SERIOUS BODILY INJURY AND OR PROPERTY LOSS READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE ASSEMBLY OR USE OF THE LP GAS GRILL To reduce the risk of a laceration hazard wear protective gloves when handling parts that have sharp edges 1 A WARNING Read and follow all instructions 2 For Household Outdoor Use Only Do Not Use Indoors or on recreational vehicles or boats Never use as a space heater Not for commercial use 3 A WARNING To reduce the risk of serious or fatal injury from breathing toxic fumes and from explosion and fire as a result of leaking gas use only outdoors in an open area with good ventilation As with all conventional fuels the burning process consumes oxygen and produces toxic gases including carbon monoxide In addition the combus
35. s shown Insert legs 1 and 2 in holes on right side of bowl and hood respectively While holding leg 3 insert leg 4 into hole on hood Carefully position leg 3 into hole in bowl and allow it to spring outward into position STEP 14 Assemble Side Tables Screw Table M6 x 45mm L Spacer 8 pcs 8 pcs ae A 9 Ta 9 D n 9 A H MLTR 9 Tama D 19T 9 Ta eSlide 8 side table spacers onto 8 M6 x 45 mm screws eInsert M6 x 45mm screws and side table spacers through bottom holes of side table and through leg Secure with M6 nuts and tighten eInsert M6 x 45mm screws and side table spacers through top holes of leg Secure with M6 nut and tighten eRepeat for other side table Note The side table folds for storage Make sure side table is secure when locked in the user position To lower side table simply grasp the front and rear of the side table lift upward and pull slightly away from the grill The table can then be pivoted down until it con tacts the cart legs Reverse the process to begin using the side table Step 15 Install Privacy Panel sik a Screw Screw M6 x 15 ST 4 0 x 10mm 1 pc installed 9 pcs in Step 1 eAttach privacy panel to back side of front legs using 1 M6 x 15mm screw on the upper left pre installed in Step 1 and also secures the Cylinder Slide Bracket See inset appropriate to your privacy panel material Secure the remainder of the privacy panel using 5 ST 4 0 x 10mm screws in
36. sun Never store a spare or disconnected LP gas cylinder under or near the LP gas grill Always turn off the gas cylinder when not in use Allow grill to cool before handling parts or cleaning Even though your LP gas cylinder may appear to be empty gas may still be present and the cylinder should be transported and stored accordingly Flavor Activator Drip Cup Always turn the LP gas cylinder valve Off when not in use Allow grill to cool before handling parts or cleaning Empty the Grease cup after each cooking session so excessive grease does not accumulate Failure to remove grease may result in grease dripping onto the cart and or a grease fire in the cup Never light the LP gas grill without the grease cup in place Before each use remove all grease from your Grease Cup Store your LP gas grill in a cool dry place Sana Make sure Grease Cup is in place before each grilling Disconnect LP gas cylinder from grill and store outside in session a dry well ventilated area away from any sources of heat Failure to remove grease from the Grease Cup may result Qr ignition Re cap LP cylinder valve with the Safety Cap in grease dripping onto the cart Remove Burner and wrap with aluminum foil to prevent insects from entering the burner holes Store wrapped Cleaning the Grill Bowl Burner on top of cooking grid Before next use remove aluminum foil and reinstall Burner Flavor Activator
37. tains use a nonabrasive scouring powder Do not use steel wool or Re E Aion S S Enz 9 EEE pa 7 Provided that the Burner is operating correctly in normal e pe econ Ue OCEAN COAN Caen tole usage burning off the residue after cooking will keep the O SUCK burner clean The Burner should be removed and cleaned annually or whenever heavy build up is found to ensure WARNING that there are no signs of blockage debris insects in either To reduce the risk of a fire beneath the grill the burner portholes the primary air inlet or the neck of the Inspect and clean burner venturi tubes for insects and Ourner See Burner cleaning instructions below insect nests How to clean the Burner Be sure burners are re installed properly before using 1 Make sure the LP cylinder and grill control knobs are grill turned off and the grill has completely cooled Inspect burners periodically if large cracks or holes arel 2 Carefully remove Grease Cup Cooking Grid and Flavor found replace the Burner Activator 3 Remove the Burner by first removing the Heat Shield from the bottom of grill Bowl Remove the two screws securing the burner also located underneath the grill SPIDER ALERT bowl 4 Remove Burner from the grill Should you notice that you burner s are getting hard to light 5 Use a pipe cleaner to clear obstructions from the Burner or the flame is not as hot as it once was Refer to the How holes and inlet hole
38. the remaining holes 13 STEP 16 Insert Drip Cup eInsert drip cup into hanger clip underneath grill bowl Drip Cup aff i Step 17 Attach LP Cylinder Note Turn all control knobs and LP cylinder valve to the Off position 2 Place cylinder on cylinder 3 Lower the cylinder slide support and hold in place lock onto collar of cylinder Orient cylinder with open and tighten wing bolts side of collar under the grill as shown Notice not all cylinders look alike 1 Loosen wing bolts on cylinder slide lock Raise to highest a position and retighten 5 Insert nipple of regulator into the cylinder nozzle opening Hand tighten coupling nut in clockwise direction Do not use tools 4 Remove the protective cap from the cylinder valve Align regulator with cylinder valve Make sure regulator hose is not near or con tacting any hot surfaces eMake sure bottom of cylinder sits in notches on cylinder support This helps prevent cylinder movement Please complete your leak test and you are now ready to use your grill 14 OPERATING AND MAINTAINING YOUR GAS GRILL GAS CYLINDER HOSE AND REGULATOR INFORMATION This LP gas grill was designed to use propane gas Propane cylinders will supply gas all year round even on cold winter days LP HOSE AND REGULATOR ASSEMBLY Using a hose and regulator assembly that has not been supplied by the manufacturer of this LP gas grill could result
39. tion products of such fuels including liquefied petroleum LP contain chemicals known to the state of 5 California and other authorities to cause cancer birth defects and other reproductive harm 4 Place your Liquefied Petroleum LP gas grill on a firm level surface Grill should be setup away from high traffic areas and combustible materials Locate your LP gas grill at least 10 feet away from your house or any building Do not use the grill in a garage breezeway carport porch or in any enclosed area Do not locate this appliance under overhead unprotected combustible surfaces 6 Have an ABC fire extinguisher accessible Never attempt to extinguish a grease fire with water or other liquids T A WARNING If your grill catches on fire e If the fire is in the grill portion and you can safely reach the control knobs then turn them off by turning knobs clockwise If you cannot safely reach the control knobs call the fire department s If the fire involves one of the hoses and you can safely reach the propane cylinder valve shut the valve off by turning LP cylinder valve handle clockwise to a full stop s If the fire involves the cylinder leave it alone evacuate the area and call the fire department e If there is any type of fire that threatens either personal safety or endangers property call the fire department 8 Check the Grease Cup for grease buildup Remove excess grease to avoid a grease fire in
40. ttach Igniter Wire eee Step 8 Mounting Hood Bowl Hinges cccceeeeeee 10 Step 9 Attach Hood 11 Step 10 Attach Hood Handle amp Handle Shield 12 Step 11 Insert Flavor Activator cccccccseceeseesseeeeees 12 Step 12 Insert Cooking Gnd eee 12 Step 13 Insert Warming Rack eee 12 Step 14 Assemble Side Tables eee 13 Step 15 Install Privacy Panel 13 Step 16 Insert Drip Cup cc cecccceeeeceeeseeeeeeeeeeees 14 Step 17 Attach LP Cylinder see 14 Ill Operating and Maintaining Your LP Gas Grrill 15 A Gas Cylinder Hose and Regulator Info 15 1 LP Hose amp Regulator Assembly eee 15 2 LP Gas Cylinder 15 3 Connect Disconnect LP Gas Cylinder 15 B Before Using Your Gn sees eee 16 1 Selecting a Location eee eee 4 Attach Flavor Activator Pins Grease Cup Hanger 2 FNC CAUMOMS tccccivaa cen incdtosctreaunetd aun onde atte anteinanaaiete 16 3 Leak Testing sees 17 C Operating the LP Gas Gn 17 1 Preparation Before COoking cccseccesseeeeeeees 18 2 Lighting with lantet sese eee 18 3 Manual Lighting of the Gn see eee 19 4 Check Your Flame sees eee ee 20 9 Grill CON ssa cnt neg Sonne eetatenteae needa 20 6 enle T 20 7 End of Cooking Session eee 20 8 Turning Off Your LP Gas Gn sees 20 D Care and Maintenance ccccccseeecsseeeeceeeeeesee
41. website Thank you for purchasing a MECO Corporation product It is important to register your grill and retain your receipt 1 800 251 7558 CONSUMER SERVICE DEPARTMENT 8 am 5 pm E S T Mon Fri www aussiegrills com MECO CORPORATION 1 423 639 1171 TELEPHONE 1500 INDUSTRIAL ROAD 1 423 639 2570 FAX GREENEVILLE TN 37745 USA Step 1 Assemble Wheel Le i SS SS Assemble Cylinder Slide Bracket to left leg using 4 M6 x 15mm Screws Assemble the Cylinder Slide Lock to the Cylinder Slide Bracket using 2 Wing Bolts Notice orient holes iY closer to this edge Gee l Screw Wing Bolt ide Loc we Cylinder Slide mee omen b B 4 pcs 2 pcs racket ae _ y a a gt Threaded holes Orient Leg Notice two holes to the front Assemble wheels and cylinder support to wheel leg using 2 axle pins and 2 cotter pins La Zo ty Orient Cylinder Support with wider spaced slots to this side Right A L Orient wheels w with protrusion touching leg L Notice Orient holes closer to Step 2 Assemble Fixed Leg this edge SONA Screw Cylinder M6 x 50mm ST 4 0 x 15mm Block Wire 2 pcs 2 pcs Orient Leg Notice two holes to the front Assemble Cart Brace to fixed leg using 2 M6 x 50mm screws Assemble Cylinder Block Wire to fixed leg using 2 ST 4 0 x 15mm screws cant Brace STEP 3 Assemble Cart WH ba Screw Nut Screw M6 x 35mm M6 M6 x 50mm 4 pcs
42. x 10mm Table Spacer asher NO 23 Problem Gas leaking from cracked cut burned hose Gas leaking from LP cylinder Gas leaking from LP cylinder valve Gas leaking between LP cylinder and regu lator connection Fire coming through control panel Grease fire or exces sive flames above cooking surface Flashback fire in or around ven turi tubes Emergencies Possible Cause Damaged hose Mechanical failure due to rust or mishandling Failure of valve from mishan dling or mechanical malfunc tion Improper installation connec tion not tight failure of seal on LP cylinder valve Fire in or around venturi tube section of the burner Too much grease build up in burner section Clogged or blocked venturi tube Solution Turn off gas at the LP cylinder Replace valve hose regulator before continuing use Replace LP Cylinder Turn off LP cylinder valve Return cylinder to gas supplier Turn off LP Cylinder valve Re install correctly or tighten cou pling nut Replace cylinder if seal is damaged See Leak Test and Connecting Regulator to LP Cylinder sections If you can safely reach the control panel turn off control knobs then close the LP cylinder valve Once fire is out and grill has cooled off Remove burner s and inspect for blockage from spi der webs nests or rust See How To Clean Burners section Replace any damaged parts Turn off control Knobs and
43. y result in leakage of propane How to Connect your LP gas cylinder See STEP 22 of Assembly Instructions for diagram 1 Make sure all of the control knobs are turned to the off position and verify that the LP gas cylinder valve is closed by turning the handle on the LP gas cylinder valve clockwise until it stops 2 Remove the protective cap from the LP cylinder gas nozzle 3 Hold regulator in a straight line with LP cylinder gas nozzle so the connection does not cross thread 4 Insert Regulator nipple into the LP cylinder nozzle opening 5 Hand tighten coupling nut in a clockwise direction Do not use tools 6 Perform a Leak Test See STEP 10 of Assembly Instructions for Leak Test Instructions How to Disconnect your LP gas cylinder 1 Turn all control knobs to the off position and turn the handle on the LP gas cylinder clockwise until it stops 2 Turn coupling nut on regulator in a counter clockwise direction until regulator is released from threaded LP cylinder gas nozzle 3 Place the protective cap over LP cylinder gas nozzle BEFORE USING YOUR LP GAS GRILL Selecting a Location Do not use an LP gas grill indoors on recreational vehicles or on a boat l This LP gas grill is for outdoor use only and should be placed on firm level surface The grill should be setup in an open area with good ventilation away from high traffic areas and combustible materials Combustible or flammable materi
Download Pdf Manuals
Related Search