Maytag MGDX6STBW Dimension Guide
Contents
1.2. Gas Dryer PRODUCT MODEL NUMBERS MGDX6STB 29 Wide Models Dryer Dimensions Front View Side View 1 o 13 mm NOTE Leveling legs should be 1 2 13 mm to match height of 3 6 cu ft capacity washer or 112 38 mm to match height of 3 8 cu ft capacity washer Installation Spacing 3 76 mm 14 max 356 mm 48 in 310 cm 24 in 155 cm sa A 140 mm Ss 17 25 mm Required spacing e1 33 4 273 4 r 849 mm 705 mm 223 4 273 4 578 mm 705 mm A B A Wide opening side swing door B Wide opening hamper door Back View 4 101 mm gt lt 301 4 768 mm 43 4 43 4 141 2 e 121 mm 121 mm 368 mm Steam Non Steam Installation spacing for recessed area or closet The dimensions shown are for the minimum spacing allowed Additional spacing should be considered for ease of installation and servicing Additional clearances might be required for wall door and floor moldings Additional spacing of 1 25 mm on all sides of the dryer is recommended to reduce noise transfer For closet installation with a door minimum ventilation openings in the top and bottom of the door are required Louvered doors with equivalent ventilation openings are acceptable Companion appliance spacing should also be considered W10646607A 12 2014 27 Wide Models Dryer Dimensions Front View
3. of Type Box louvered Angled 90 turns of vent hoods hoods Acceptable Style or elbows Rigid metal 64 ft 20 m 58 ft 17 7 m o ro T7 P gis metar 54 16 5 46 46m CM P Rigid metar 4419 4 m 26 17 6 m o Rigid metal 25 8 10 7 m 29 8 6m P Rigid metar_ 27 8 62 m NOTE Side and bottom exhaust installations for 27 wide models have a 90 turn inside the dryer To determine maximum exhaust length add one 90 turn to the chart Angled Hood Determine vent path Select route that will provide straightest and most direct path outdoors Vent System Chart Em Plan installation to use fewest number of elbows and Long Vent Models Only turns Number of Type Box louvered or m When using elbows or making turns allow as much 90 turns of vent Angled hoods room or elbows as possible 0 __ Rigid metal 120 ft 36 6 m m Bend vent gradually to avoid kinking 1 Rigidmetal 110 ft 83 5 m m Use as few 90 turns as possible ck Rigid metal 100 ft 80 5 m 3 Rigidmetal 90 ft 27 4 m 4 Rigidmetal 80 ft 24 4 m 5 Rigidmetal 70 ft 21 3 m Because Whirlpool Corporation policy includes a continuous commitment to improve Dimensions are for planning purposes only For complete details see Installation our products we reserve the right to change materials and specifications without notice Instructions packed with product Specifications subject to change without notice
4. used An individual manual shutoff valve must be installed within 6 ft 1 8 m of the dryer in accordance with the National Fuel Gas Code ANSI 2223 1 ELECTRICAL REQUIREMENTS A 120 volt 60 Hz AC only 15 or 20 amp fused electrical supply is required A time delay fuse or circuit breaker and a separate circuit are recommended WATER STEAM MODELS ONLY REQUIREMENTS The dryer must be connected to the cold water faucet using new inlet hoses Do not use old hoses Do not overtighten Damage to the coupling can result VENTING REQUIREMENTS Determine vent length and elbows needed for best drying performance Exhaust venting Exhaust your dryer to the outside 4 102 mm diameter vent is required Rigid or flexible metal exhaust vent must be used Do not use plastic or metal foil vet Exhaust hood must be at least 12 305 mm from the ground or any object that may be in the path of the exhaust E Use following Vent System Chart to determine type of vent material and hood combinations acceptable to use NOTE Do not use vent runs longer than those specified in Vent System Chart Exhaust systems longer than those specified will Exhaust hoods E Shorten life of dryer Recommended Styles y m Reduce performance resulting in longer drying times and increased energy usage qz The Vent System Chart provides venting requirements that will help achieve best drying performance Vent System Chart Louvered Hood Box Hood Number
5. 27 686 mm OOT 43 1092 mm 1 2 13 mm Back View 33 8 14 85 mm 356 mm Non Steam Installation spacing for recessed area or closet The dimensions shown are for the minimum spacing allowed Side View 223 4 291 2 1 33 4 291 2 578 mm T 749 mm g 349 mm 749 mm A B A Wide opening side swing door B Wide opening hamper door Installation Spacing 14 max 356 mm a ecett yi Bia Ss 140 mm N ss 1 a 25 mm Required spacing E Additional spacing should be considered for ease of installation and servicing E Additional clearances might be required for wall door and floor moldings E Additional spacing of 1 25 mm on all sides of the dryer is recommended to reduce noise transfer E For closet installation with a door minimum ventilation openings in the top and bottom of the door are required Louvered doors with equivalent ventilation openings are acceptable Companion appliance spacing should also be considered INSTALLATION REQUIREMENTS GAS SUPPLY REQUIREMENTS Gas supply This dryer is equipped for use with Natural gas Dryer can be converted to L P gas When rigid pipe is used it should be 1 2 IPS When acceptable to the gas supplier and local codes 3 8 approved tubing may be used for lengths under 20 ft 6 1 m For lengths over 20 ft 6 1 m larger tubing should be used Pipe joint compounds resistant to the action of L P gas must be
Download Pdf Manuals
Related Search