Maxtor 4 CH User's Manual
Contents
1. 22 220nennnnneneneennnnnnnnnne 19 APPENDIX 2 REPLACE THE HDD 19 APPENDIX 3 PIN CONFIGURATIONS ccceeennnnnnnnnnnn 20 APPENDIX 4 RECORDING SPEED 22 APPENDIX 5 NETWORK APPLICATION 23 DVR Features e Wavelet compression format replaces Time Lapse VCR Multiplexer Quad e On Screen Display and Remote Control via Video Server amp PC e Picture in picture PIP and Picture on Picture POP function in live e Alarm input amp output function e Video loss detected on each channel e Multiplexer amp Quad recording mode switching e Recording rate up to full size 30 fields sec or Quad size 240 fields sec e Support 1 HDD IDE TYPE over 250 GB e Multiple quick search by date time alarm full list e Security password protection e RS 232 RS 485 communication protocol PACKAGE CONTENT Digital Video Recorder Users Manual Accessories pack Accessories pack Power Adapter and Cord Warning 1 Please check the package to make sure that you receive the complete components shown above 2 This adaptor is DC 19V 2A User can find the adaptor for replacement at a computer shop if the adaptor is broken Before Operation INSTALLATION GUIDE 1 Connect cameras and monitor to the DVR2. 2 Shown below is an example of connecting the DVR to your existing Observation System 3 Install HDD The compatible HDD Brands are listed in the following table Please refer to page 19 Appendix 1 for installation instructions The HDD must be installed before turning on the DVR If HDD is not installed the DVR would function as a 4 CH multiplexer internet ideo Server E SUT a ki a 300000 Camera 4 Call Monitor COMPATIBLE HARD DISK MODELS Manufacturer Model Tt Capacity Rotation DiamondMax 536DX 60GB 4W060H4 FRONT PANEL LED LIGHT The LED Lightis ON under following condition e HDD HDD is reading or recording e HDD Full HDD is full ALARM To tum off the ALARM LED light please refer to page 13 and set the ALARM mode as OFF TIMER When Timer is Enabled e PLAY Playing mode REC Recording mode o Press MENU to enter main menu ENTER Press ENTER for confirmation SEARCH Press SEARCH for searching recorded video LE POP Press button for Picture on Picture screen Picture in Picture PIP Press PIP button for Picture in Picture screen Press button can change the setting in the menu 4 chann
3. 4 channels Call Monitor Output Composite video signal 1 Vp p 75Q BNC LEE Refresh Rate Up to 240 fields sec for NTSC 200 fields sec for PAL Multiplex Up to 30 fields sec for NTSC 25 fields sec for PAL Quad field Up to 120 fields sec for NTSC 100 fields sec for PAL Quad frame Up to 240 fields sec for NTSC 200 fields sec for PAL Dwell Time Programmable 1 15 Sec Picture in Picture Yes Movable Key Lock Video Adjustable Hue Color Contrast Brightness Adjustable farm input ete Alarm Output COM N O N C Remote Control RS 232 or RS 485 Time Display Format YY MM DD DD MM YY MM DD YY OFF o Operation Temperature 10 40 8 letters RS 232C RS 485 bps 115200 57600 19200 9600 4800 3600 2400 1200 Dimension mm 343 W x 223 L x 59 H NetWeight oo sk AA e Specifications are subject to change without notice NTSC 4CH x 30IPS 120 fields sec PAL 4CH x 25IPS 100 fields sec NTSC 4CH x 60IPS 240 fields sec PAL 4CH x 50IPS 200 fields sec 18 APPENDIX 1 INSTALL THE HDD Follow these steps carefully in order to ensure correct installation HDD Bracket HDD Power Cable Fig 1 Fig 2 Fig 3 Step 1 Remove the lid and unscrew the screws from HDD bracket module Step 2 Insert the HDD into the HDD bracket and screw the four screws The bottom side is power side as chart shows refer to the Fig 1 Step 3 Connect the HDD power cable to the HDD refer to the
4. ALARM The options are as following NTSC 30 15 8 4 25 1 PAL 25 12 6 3 25 1 ALARM 4 QUALITY ALARM ENABLE There are four recording quality settings during an ALARM ALARM DURATION BASIC BEST HIGH NORMAL RECORD IPS QUALITY 9 RECORD MODE RECORD MODE QUAD FRAME There are three recording settings QUAD FRAME QUAD FIELD MULTIPLEX DW ELL 1 NORM To setup the DWELL time period that each channel auto sequentially shows on call monitor The level is from 1 to 15 Sec or OFF 2 ALARM To setup the DWELL time period when alarm input is triggered The level is from 1 to 15 Sec or OFF DWELL NORM ALARM PIP 1 FULL SCREEN To setup the full screen background picture display 2 PIP SCREEN To set up the picture with a 1 9 size screen insert 3 POSITION There are six position settings D L D M D R U L UM U R PIP FULL SCREEN DISPLAY PIP SCREEN POSITION 1 TITLE DISPLAY To set the title shown on monitor or not 2 OSD COLOR Selectthe OSD On Screen Display color The options are YELLOW GREEN CYAN BLUE PINK GRAY WHITE RED 14 3 LOSS SCREEN Retain the last picture or select the LOSS SCREEN color The options are GREEN BLACK BLUE and RETAIN 4 TIME POSITION To setthe OSD POSITION shown on monitor The options are NORMAL or CENTER DISPLAY TITLE DISPLAY YES OSD COLOR YELLOW LOSS SCREEN GREEN TIME POSITION NORMAL REMOTE 1 REMOTE MODE Set t
5. Fig 2 Step 4 Attach the HDD connector to the 40 pin pinhead and screw the HDD and the DVR machine together refer to the Fig 3 Step 5 Pull the sides of the lid apart slightly and push the lid down Note Do not try to retrieve the HDD data by PC The video file cannot be read by PC Operation on PC would damage the FAT table of the hard disk APPENDIX 2 REPLACE THE HDD Follow these steps carefully in order to ensure correct installation Step 1 Remove the lid Step 2 Unscrew the screws and take out the HDD from DVR machine carefully refer to the Fig 3 Step 3 Remove the HDD power cable from the HDD refer to the Fig 2 Step 4 Unscrew the four screws connected the hard drive to the bracket and remove the HDD bracket module Repeat those steps according to the Install the HDD section for resetting another HDD refer to the Fig 1 Step 5 Pull the sides of the lid apart slightly and push the lid down Note When HDD works for a period of time the surface temperature will be high please notice it 19 APPENDIX 3 PIN CONFIGURATIONS 15 pin com port o oT m D ra o Ha om Ky es in R5465 ALARM INPUT2 DISK FULL ALARM INPUTS ALARM INPLITA ALARM RESET EXTERNAL ALARM NC EXTERNAL ALARM COM EXTERNAL ALARM NO oO O o o O09 olala NI LA 9 pin com port ALARM INPUTA Rasa ALARM INPUT2 DISK FULL ALARM INPUTS ALARM INPUT4 ALARM RESET EXTERNAL ALARM NC EXTERNAL ALAR
6. M HD ERR 26 DEC 2002 03 00 00 CI VLOSS Video loss on Chi M HD WARM 26 DEC 2002 03 00 00 PWR REST 26 DEC 2002 03 00 00 C2 ALARM Channel 2 has been triggered by external I O alarm DMA ERROR 26 DEC 2002 03 00 00 SYSTEM ERROR System fail M HD REPL 26 DEC 2002 03 00 00 t CLEAR POWER RESTORE Power restored OPERATION OPTIONS VIDEO LOSS Screen will display VLOSS in the center of display picture if the video input is not connected properly SEARCH 1 LAST RECORD Play the last recorded piece of video LAST RECORD FULL LIST 2 FULL LIST ALARM LIST List all recorded video on the HDD which sorted by time TIME SEARCH dh Manual Recording cg Alarm Recording Timer Recording M Storage in Master HDD 2003 JAN 01 01 02 03 M SA ENBE 1 2003 JAN 05 05 02 03 M NOTE It will display different color on each record list tH 2003 MAR 12 04 02 03 M mention above 2003 APR 02 03 02 04 M fy 2003 MAY 01 05 02 03 M E o 2003 AUG 09 01 02 01 M List all recorded video triggered by Alarm PAGE UP gt PAGE DOWN NOTE If there are no Alarm in the record the screen will display EMPTY 4 TIME SEARCH Enter the specific time date KEY LOCK For advanced security you can Lock the buttons on your DVR Key Lock prevents other people from using the system Press ENTER and MENU atthe same time to enable Key Lock Press ENTER and MENU atthe same time and key in password Default 0000 then
7. appear for 3 seconds and then return to 4 CH Multiplexer display mode 2 To switch the system pull out the AC power cord before you reconnect the power press FF to NTSC system or REW to PAL system and then reconnect the AC power cord the DVR will auto detect the system OPERATION RECORDING The DVR offers 3 recording modes Refer P 22 for advanced setting of recording speed and resolution Under the recording status if power Is off accidentally recorded video will still be stored in the HDD DVR will return to original recording setting after power restores again While you press REC button on the screen you will find the date time recording type the available HDD space inGB and the letter fh represents the recording mode OW HDD Overwrite NOTE 1 When the HDD is full under O W Recording mode previous recorded files will be overwritten without further warning notices 2 If the HDD space is only 5 GB left it will display 5 GB on the up right screen in orange color and it will buzz for seconds so as in 4GB 3GB 2GB and 1GB If the O W Recording mode NOTE 1 is on it won t have the warning buzzer OW HDD Overwrite There are 3 recording modes Alarm Timer and Manual Recording 2002 JAN 01 01 02 03 ow 1 ALARM RECORDING DVR is triggered by an alarm input symbol will be shown on the triggered channel refer to page13 2 TIMER RECORDING Recording is schedu
8. 4 CH Digital Video Recorder Please read this instructions thoroughly before operation and keep the manual in a safe place for further reference 771 A V 1 0 WARNING All the safety and operating instructions Should be read before operation The improper operation may cause permanent damage WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTU NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL SOCKET OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE e This adaptor is only for this machine Do not use it for other electronic products or it may damage other products Please lift and place this equipment gently e Do not expose this equipment from direct sunlight and keep it away from sources of intense heat Do not use this equipment near water or in contact with water Avoid dusty or humid place Do not switch the Power On amp Off within short period of time within 3 seconds e Do not block the ventilation holes at the top and bottom of the unit Do not attempt to service this equipment by yourself e Installation should be made by qualified service personnel Do nottry to retrieve the HDD data by PC The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within
9. LAN e Auto Network Reconnection ANR Upgrade firmware amp AP from FTP site via Video Web Server Watch dog function supported Support Dynamic IP address e 4 alarm inputs supported Duplex function record and playback simultaneously at client site e Auto e mail warning system which will remind you if external alarm happened Intelligent non stoppable recording function after ANR Multi AP screens supported Unique video player DVR Control 1 Connect the Sub D plug of Video Web Server with our own brand DVR products 2 Set the Remote function in the DVR products NOTE Remote mode RS 485 Baud rate 2400 ID same as I O port setting in the Video Web Server 3 Set the I O Port Setting in the system config of Video Web Server Portl DMR 4 Device ID 20 Video Web Server Video Web Server 1CH 4CH OVA ALARM Es GND INPUT SAAMI AL a WPUT mU a Kiiza Ta NL Pree te ie Briss VDES LOBE ua SIM TEA DT PEL START Ei Rh EIN EXTERNAL ALATA M EXTERNAL LAPU CON ESTERMAL ALARM NO ALARM NORMAL INPUT LOW 1 4 CH DVR REMOTE REMOTE MODE RS485 BAUD RATE 2400 Server F Hai Mark 224 25 HE DHE IS F P sMenod dE STAMP Mal Setting Mame Booo Marom DO 23
10. M COM EXTERNAL ALARM NO 20 PIN 1 RS232 TX RS 232 DVR can be controlled remotely by an external device or control system such as a control keyboard using RS 232 serial communications signals PIN 2 RS232 RX RS 232 DVR can be controlled remotely by an external device or control system such as a control keyboard using RS 232 serial communications signals PIN 3 4 5 6 ALARM INPUT To connect wire from ALARM INPUT PIN 3 4 5 6 to GND PIN 9 connector DVR will start recording and buzzer will be on When alarm has been triggered signal becomes Low and it will stop all alarm activities Under normal operation signal remains High PIN 7 EXTERNAL ALARM NC Under normal operation COM connect with NC and disconnect with NO But when alarm triggered COM disconnect with NC and connect with NO PIN 8 EXTERNAL ALARM NO Under normal operation COM will disconnect from NO But when Alarm triggered COM will connect with NO PIN 9 GND GROUND PIN 10 RS485 B DVR can be controlled remotely by an external device or control system such as a control keyboard using RS 485 serial communications signals PIN 11 RS485 A DVR can be controlled remotely by an external device or control system such as a control keyboard using RS 485 serial communications signals PIN 12 DISK FULL OUTPUT When HDD is full it sends a signal to trigger next DVR record mode if you install another DVR Under normal o
11. Sat Sun Daily that you wish to schedule the DVR to automatically record NOTE 1 Change the date by and buttons 2 If you have selected the date and Timer recording set from that specific day to a new day then the Timer Recording Schedule will be set as whole week For specific date of Timer Recording Schedule it is not recommended to set Ending Time over 23 59 For example If you set Timer Schedule Day as Sunday and START from 11 30 but End on 00 20 then Recording Timer Schedule is set as from every Sunday s 11 30 to next Sunday s 00 20 If you only want to set Recording Timer Schedule from every Sunday 11 30 to Monday 00 20 then you should set Recording Timer Schedule as Sunday from 11 30 to 23 59 and Monday from 00 00 to 00 20 3 It is not suggested that users press STOP button or restart the system during setting time In doing so the recording will stop and users can resume recording by pressing ENTER MENU 11 2 START Setthe time to start the recording 3 END Setthe time to end the recording 4 IPS IMAGES PER SECOND NTSC 30 15 8 4 2 1 PAL 25 12 6 3 2 1 5 QUALITY Selectthe quality of recording image BEST HIGH NORM and BASE 6 MODE There are three recording mode settings QUAD FRAME QUAD FIELD MULTIPLEX NOTE To ensure the best recording quality we don tsuggest the users switch a different recording mode during the period of re
12. VLOSS ALARM When the setting is ON the alarm will start by the setting of Buzzer EXT alarm or Alarm Duration 4 KEY MUTE To setthe KEY MUTE When the setting is YES there will be no sound when you press any key 5 HDD OVERWRITE To set the HDD OVERWRITE When the HDD is full under O W recording mode previously recorded files will be overwritten without further warning notices when the HDD OVERWRITE is ON 10 6 MESSAGE LATCH To select whether the DVR messages will disappear after 10 seconds or remain on screen NO is the default setting which the messages will disappear after 10 sec NOTE Video loss and Alarm messages will be shown the same as Alarm Duration time 7 DATE DISPLAY To set the date Y M D M D Y D M Y and OFF on monitor or not 8 DATE To set the date on the DVR 9 TIME To set the time on the DVR 10 CLEAR HDD SYSTEM BUZZER EXT ALARM VLOSS ALARM KEY MUTE HDD OVERWRITE MESSAGE LATCH DATE DISPLAY D M Y DATE 26 DEC 2003 FRI TIME 22 55 34 CLEAR HDD YES SYSTEM RESET YES Delete all the contents of the HDD When you choose YES on this option press ENTER and you will be prompted with the question shown Press gt to clear HDD or press lt to cancel 11 SYSTEM RESET Reset all system to the factory default settings Select YES and press ENTER button TIMER 1 DAY Select the day or days of the week Mon Fri
13. al O expansion 2 VIDEO INPUT 1 4 Connect to video source such as camera 3 MAIN Connect to Main monitor 4 CALL Connect to CALL monitor Show the Switch Display When alarm is triggered the call monitor will show the triggered channel according to the system setting 5 POWER Please use the provided power cord Warning 1 This adaptor is only for this machine Do not use it for other electronic product or it may damage other products 2 This adaptor is DC19V 2A User can find the adaptor for replacement at a computer shop if the adaptor is broken 6 FAN OPTIONAL For ventilation Note If the ambient temperature is high or ambient ventilation is bad we suggest to install a fan on the rear panel Basic Operation GETTING STARTED Before using the DVR please have a HDD installed ready or it will function as 4 CH multiplexer refer to Appendix 1 for installation or removal of a HDD 1 Connect the AC power cord and plug into an electrical outlet The POWER LED will turn into orange color and other red LED indicators will turn ON It takes approximately 5 to 15 seconds to boot the system with the message HDD Detecting Once successfully connected the POWER LED will change to green color and the Alarm LED will be ON 2 Before operating the DVR set the system time first refer to page 10 NOTE 1 If the HDD is not installed correctly or not installed the HDD not found message will
14. cording 7 TIMER ENABLE When TIMER ENABLE Is YES press menu button you can see the timer diagram according to your setting TIMER DAY START END DAILY 01 00 22 00 BEST OFF 00 00 00 00 BEST OFF 00 00 00 00 BEST OFF 00 00 00 00 BEST OFF 00 00 00 00 BEST OFF 00 00 00 00 BEST OFF 00 00 00 00 BEST OFF 00 00 00 00 BEST TIMER ENABLE YES 00 05 D6 17 12 17 AMAT TT 00MIN ANI MENMA MAAT TNMM 3 BYU OOO VUm Ouuu HMTD maoan 7 oC amam MMAM MNT Sra OOOO Ooo WOMAD OC EO On Citk 05 O8 1 12 17 AMT TAM MMMM am amam amina ATM TM Su quando mena THU BOOOTO Ma Cor ooo AMT MMTT WANA amem BWW UO WOOO Co oo SUN BIO DO WOOO TUUU QLT MODE Q FR Q FI Q FI Q FR Q FR Q FR MUX Q FI 18 23 TINATA TITANA MUUNNA DITRA MAMA TIA a A ILE KUANZA MTE MTM manng minag MTM wu LO Go oa LA Oo CAMERA 1 TITLE Assign a title to each camera Initially each title is the camera s number Max 8 characters 2 ALARM Select LOW OFF HIGH for alarm polarity The default value is LOW CAMERA TITLE ALARM REC BR CAMERAO1 LOW ON 18 CAMERAO2 OFF OFF 18 CAMERAO3 HIGH OFF 18 CAMERA04 HIGH ON 18 12 3 REC RECORD Setup which channel you wantto record ON when alarm input is triggered DVR will record alarming channel more frequently For example when CH01 Is triggered the record method will become 1 2 1 3 1 4 OFF DVR will not record 4 BR BRIGHTNESS Adjust the bri
15. el display mode Press button for 4 CH display modes Press button can change the setting in the menu SLOW To slow down the speed of playing mode STOP w PAUSE A PLAY REC CAMERA SELECT 1 4 ENTER SEARCH FF Play video fast forward Press FF button again to adjust speed from 1 2 4 8 16 32 times gt Under setup mode it works as Right button e REW Play video fast backward Press REW button again to adjust speed as 1 2 4 8 16 32 times e 4 Under setup mode it works as Left button e STOP Under DVR Record Play mode it can stop the action e W Under setup mode it works as Down button Pause Under DVR play mode it can pause the action A Under setup mode it works as Up button Press PLAY to playback recorded video Press REC to Start recording Press the Camera Select 1 4 to select the channel During the LIVE or PLAY mode press both ENTER and SEARCH buttons to switch the NORMAL or SHARPNESS display refer to page 9 REAR PANEL lt DN V VIDEO p OUT gt 000000 EXTERNAL I O 1 EXTERNAL I O e Controlled remotely by an external device or control system like Video Web Server Alarm input extern
16. ghtness of each channel The level is from 0 to 63 5 CT CONTRAST Adjust the contrast of each channel The level is from 0 to 63 6 CL COLOR Adjust the color of each channel The level is from 0 to 63 7 HUE HUE Adjust the hue of each channel The level is from 0 to 63 RECORD 1 RECORD IPS Select the recording speed The options are as following NTSC 30 15 8 4 25 1 PAL 25 12 6 3 2 1 2 QUALITY There are four quality settings BEST HIGH NORMAL BASIC NOTE The relationship of Record time IPS and Record quality please refer to page 22 Recording Speed 3 RECORD MODE RECORD There are three recording settings QUAD FRAME QUAD FIELD RECORD IPS 30 MULTIPLEX QUALITY NORMAL RECORD MODE QUAD FRAME ALARM 1 ALARM ENABLE Alarm will be triggered by event occurrence when the setting Is YES 2 ALARM DURATION Setthe reaction time of the alarm mode responds to a buzzer Default setting is 10 Sec Options are 10 Sec 15 Sec 20 Sec 30 Sec 1 MIN 2 MIN 3 MIN 5 MIN 10 MIN 15 MIN 30 MIN ALWAYS AUTO NOTE 1 Video loss and Alarm messages will be shown the same as Alarm Duration time 2 When the setting is AUTO the alarm duration time is according to the setting of the external alarm device 3 During ALARM DURATION S setting time users can restart ALARM function by pressing both ENTER STOP buttons 18 3 REC IPS Select the images per second of recording during an
17. he remote mode for connection with computer via RS 232 or RS 485 Please refer to page 20 amp 21 for RS 232 amp RS 485 Remote Control 2 BAUD RATE Set the remote protocol transmitting baud rate Available options are 115200 57600 19200 9600 4800 3600 2400 1200 3 ID To control different DVR by setting remote protocol ID number can be set from 000 to 255 REMOTE REMOTE MODE BAUD RATE ID USER 1 USER To setup the user account for controlling It allows 8 users setting Supervisor Control all the functions Other Users View all functions except the menu setting 2 PASSWORD USER To setthe security password for each account The maximum length of user s password Is 4 PASSWORD Characters SUPERVISOR 0000 USER 1 0000 USER 2 0000 USER 3 0000 USER 4 0000 USER 5 USER 6 USER 7 NOTE To switch to different USER press ENTER MENU buttons to KEY LOCK and then enter the different user s password to UNLOCK EVENT A single page can display 16 recorded events Press lt 4 or b to change the pages or press A W to CLEAR the EVENT record DISK FULL HDD is full PWR REST Power restored M HD REMS HDD removal M HD REPL HDD replace M HD ERR HDD error M HD WARM HDD warning C1VLOSS 26 DEC 2002 03 00 00 K UNLOCKS Key is unlock C2 ALARM 26 DEC 2002 03 00 00 K UNLOCKS 26 DEC 2002 03 00 00 DMA ERROR DMA error Direct Memory Access
18. led by a Timer It will indicate by the symbol t refer to page11 3 MANUAL RECORDING Recording Is initiated manually by pressing the REC button Symbol ty will be shown PLAY BACK Press PLAY button the DVR will show the last recording 1 FAST FORWARD F F amp FAST REWIND F R NJ You can increase the speed of Fast Forward and Rewind on the DVR In the Play mode press gt gt once to get 2X speed forward and press twice to get 4X speed and the maximum speed can reach 32X Press lt a once to get 1X speed rewind and press twice to get 2X speed and the maximum speed can reach 32X SLOW FORWARD S F amp SLOW REWIND S R You can also slow down the speed of Forward and Rewind on the DVR In the Play mode press the SLOW button and you will enter Slow mode Press SLOW once to get 1 2X speed forward and press gt gt to get 1 4X speed and the slowest speed can reach 1 32X Press lt a once to get 1 2X speed rewind and press twice to get 1 4X speed and the slowest speed can reach 1 32X PAUSE You can pause the playback and the image will be displayed on the screen STOP Press STOP button under any circumstance DVR will return to live monitoring mode IMAGE J OG DIAL It will allow you to manually view video frame by frame one image ata time While in PLAY mode press PAUSE it will pause the screen Press gt gt b
19. peration the signal remains High But when disk full DVR will send the Low signal PIN 14 ALARM RESET INPUT To connect wire from ALARM RESET PIN 14 to GND PIN 9 connector it can disable ALARM An external Signal to ALARM RESET PIN 14 can be used to reset both ALARM OUTPUT signal and DVR s internal buzzer When alarm has been triggered signal becomes Low and it will stop all alarm activities Under normal operation Signal remains High PIN 15 EXTERNAL ALARM COM Under normal operation COM connect with NC and disconnect with NO But when alarm triggered COM disconnect with NC and connect with NO 21 APPENDIX 4 RECORDING SPEED The Record Time is different based on Recording Speed Recording Quality and Recording Mode Please refer to following table The HDD capability is 250GB WAA ps 3 15 8 4 2 ao wi DO e Best 48hr 98hr 200hr 400hr 600hr hr 124hr 251hr 500hr 752hr 1503hr QUAD ELO 160hr 332hr 668hr 1335hr 2004hr 4005hr 100hr 200hr 300hr 600hr QUAD FRAME 125hr 250hr 376hr hr 100hr 200hr 400hr 60lhr 1207hr ADD HDD Type o DBB GB Note Above data is obtained from actual test of recording normal TV program For Reference Only 22 APPENDIX 5 NETWORK APPLICATION Video Web Server Features Compatible with most of CCTV Products empower any video output device watching and controlling on the Internet or
20. press ENTER to disable Key Lock NOTE To switch to different USER press ENTER MENU buttons to KEY LOCK and then enter the different user s password to UNLOCK RS 232 REMOTE PROTOCOL You can use the PC keyboard to simulate DVR keypad DATA REMOTE PROTOCOL using 8 bit data 1 start bit gt Istop bit FUNCTION CODE ASCH FUNCTION CODE ASCII KEY QUAD 0x51 Q KEY KEY LOCK Ox4B K kevu oss pu po AAA TROUBLESHOOTING When malfunction occurs it may not be serious and can be corrected easily The following table describes the most common problems with their solutions Please read thoroughly before calling your DVR dealer PROBLEM SOLUTION No power Check power cord connections Confirm that there is power at the outlet Not working when press any Check if it is under Key Lock mode button Press MENU amp ENTER to exist Key Lock mode No recorded video Check if the HDD is installed properly Timer Record enable does not Check if the Time Enable is set to YES working No live video Check camera video cable and connections Check monitor video cable and connections Confirm that the camera has power Check camera lens setting To switch the system press FF to NTSC system and REW to PAL system Refer to Page 8 Getting Started NTSC amp PAL System switch 17 SPECIFICATIONS mera Input Sign RR Main Monitor Output Ha Composite video signal 1 Vp p 75Q BNC
21. the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance TABLE OF CONTENTS What do you FEATURES mimi 3 PACKAGE CONTENT nana nan 3 BdoreOpeation INSTALLATION GUIDE 4 FRONT PANEL 22 22 nnn anne aa nnn 5 REAR PANEL nnnnnnnn nnn nn ennn een 7 Basic Operation GETTING STARTED nnnnnnnnnnnnnnnnnn een 8 e OPERATION n nnnnn nnn maana 8 Deailed Menu Sup MAIN MENU 0 mmama 10 e MENU OPTIONS mmama 10 Advanced Operation OPERATION OPTIONS n n nnn nnn 16 KEY LOCK n n nonane nnn nn nn nnn nnn enn nnn enn 17 e RS 232 PROTOCOL nnn annem nnn nnn nnn ence 17 TROUBLE SHOOTING n nnnnnnnn nnn nnn nnn n een nee 17 e SPECIFICATIONS nn mmama 18 APPENDIX 1 INSTALL THE HDD
22. utton advances the frozen screen one image forward Press lt 4 button moves back one image Note During the LIVE or PLAY mode press both ENTER and SEARCH buttons to switch the NORMAL or SHARPNESS display CAMERA SELECT 1 4 Press Camera Select 1 4 to select the camera to display in full screen There are 11 options available in the Main Menu TIMER Program Timer Recording CAMERA Camera Setup RECORD Recording Mode Setup ALARM Alarm Setup DWELL Dwell time Setup PIP Picture in Picture Setup DISPLAY Display Mode Setup REMOTE Remote Control Setup USER User Password Setup SYSTEM System Setup EVENT Event List Outlined below are the buttons used for Menu setting A and W Scroll up and down within a menu option e lt and PD Scroll sideways within a menu option that has been selected e and Increase and decrease the number or change values when an option is selected and is blinking e ENTER Select a submenu an option under a submenu for browsing modification e MENU Complete modification of a menu option exit a menu MENU OPTIONS SYSTEM 1 BUZZER Set the BUZZ ON it will buzz by event occurrence 2 EXT ALARM To setthe EXT ALARM It will be trigged by event occurrence when the setting is ON 3 VLOSS ALARM To setthe
Download Pdf Manuals
Related Search