Master Lock Datsen Back-up Camera 4843 User's Manual
Contents
1. term of any limited or implied warranty or in the event that any limited warranty fails of its essential purpose in no event will MASTER LOCK COMPANY LLC s entire liability exceed the purchase price of this product Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages so the above limitations or exclusions may not apply to you This limited warranty gives you specific legal rights and you may also have other rights which vary from state to state and province to province www masterlock com Master Lock Company LLC Milwaukee WI 53154 U S A 800 308 9244 Master Lock Canada Oakville Ontario L6H 5S7 Canada 800 227 9599 2009 Master Lock Company All Rights Reserved 104115 02 092. Master oci Hardware and Components Included 4843DATSEN Back Up Camera Instructions N Wireless Antenna 1 o Camera with Guide Hood 1 Mounting the Camera Monitor 1 Power Cable 1 Vent Clip 1 wh Flexible Mounting Arm w Suction Cup Base 1 The camera has two basic mounting options 1 The camera figure 1 can be mounted inside a 1 1 2 figure 2 or 2 figure 3 hitch receiver tube Slide the camera assembly into the hitch tube The magnet in the camera base will hold it securely in place however the plastic guide on the camera bracket will help line the assembly up with the hitch pin opening and allow a standard or locking hitch pin to be used for additional security 2 The camera can also be mounted to any metal surface using the magnetic base figure 4 The soft pads on the base will prevent sliding or scratching and the camera bracket can pivot up to 90 to allow the field of view to be adjusted Figure 3 2 Tube Figure 2 1 1 4 Tube Figure 1 Antenna gt Transmitter Housing gt Guide Hood Pass thru T connector gt Figure4 pa Connecting the Camera CAMERA POWER CONNECTION The camera is powered by plugging the camera connector into the vehicle s towing plug The camera has a 4 position connector which will attach directly to many vehicles and has a pass though design that will all
3. as all other wireless devices may be subject 3 If there is no picture on the display to interference caused by cell phones Bluetooth headsets Wi Fi routers power lines a Set the monitor to channel 4 if needed b Turn on the vehicle lights 4 Adjust the monitor antenna for the best picture and other various electrical equipment including other cameras This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment AN IMPORTANT SAFETY INSTRUCTIONS PLEASE READ THIS OWNER S MANUAL CAREFULLY BEFORE INSTALLING AND USING YOUR CAMERA RETAIN THIS MANUAL FOR FUTURE REFERENCE Do not use this camera as a substitute for rear view mirrors side view mirrors or for any other motor vehicle equipment mandated by law This product does not relieve vehicle operators of their responsibility to insure they can safely back up their vehicle Back up cameras have a limited field of vision and do not provide a comprehensive view behind the vehicle Accordingly use this camera only as a supplement to mirrors and your own eyesight to determine if it is safe to back up Do not back up until you are su
4. f the vehicles and their towing attachments After aligning the vehicles with the camera visually confirm that the towing configuration is secure Do not use the camera view as a subsitute for recommended periodic inspection of the towing configuration during use When towing the camera system will only show the front of the towed vehicle Be sure that your towing vehicle and towing configuration is equipped with appropriate mirrors and other vision aids to allow you to see behind the towed vehicle gt gt gt PPP eooo ONE YEAR LIMITED WARRANTY If this product fails due to a defect in materials or workmanship within one year of purchase Master Lock Company LLC will replace it free of charge with proper proof of purchase Simply contact Master Lock at www masterlock com for replacement information This warranty does not cover products which have been abused altered damaged misused cut or worn TO THE EXTENT PERMITTED BY LAW MASTER LOCK COMPANY LLC DISCLAIMS ALL OTHER IMPLIED OR EXPRESS WARRANTIES INCLUDING ALL WARRANTIES OF MERCHANTABILITY AND OR FITNESS FOR A PARTICULAR PURPOSE LIMITATION OF LIABILITY This warranty is your sole remedy and MASTER LOCK COMPANY LLC shall not be liable for any damages whether direct indirect incidental special consequential exemplary or otherwise including property damage lost revenues and lost profits arising out of any theory of recovery including statutory contract or tort Notwithstanding the
5. outlet and verify the cable does not interfere with the safe operation of the vehicle or access to any vehicle controls 2 To use the mounting arm slide it into the mounting slot figure 7 and remove the vinyl protector from the base place it firmly on a smooth surface and rotate the small cam near the base of the arm 3 To use the vent clip slide it into the monitor mounting slot figure 7 and gently press the clip and monitor over the vehicle air vent fins POWER CONNECTION 1 Insert the small DC plug figure 10 of the power cable into the right side of the monitor figure 12 2 Insert the larger 12 Volt power plug figure 10 into the vehicle power socket The red LED figure 11 will come on if the vehicle socket has power Notice Depending on the make model of the vehicle the ignition may need to be turned on or to the accessory position for the 12V socket to have power Blue LED Power and Wireless Channel Indicator figure 11 When the monitor is ON the blue LED will be lit The location of the blue LED also indicates what channel the display is set to display Power Button figure 7 Press the Power button to turn the display ON the blue LED will be lit to indicate the monitor is ON Press it again to turn the display OFF the blue LED will turn off Wireless Channel figure 12 This display can accept 4 different channels of wireless transmission To change the channel press the CH button and it will go
6. ow it to be plugged between the vehicle and trailer Some vehicles may need a 7 position to 4 position adapter figure 5 which is not included NOTE A commonly available 4 position tow wire extension not included will allow the camera to be mounted farther away from the vehicle plug for gooseneck or fifth wheel trailer hitching up applications Notice Depending on the make model of the vehicle the running lights or headlights may need to be turned on to power up the vehicle s tow plug Figure 5 7 Position gt to 4 Position Adapter E ia aii s Showin gt hed ie pe ae at pas gS Connecting the Monitor and Antenna ATTACHING THE ANTENNA The wireless antenna figure 6 attaches to the threaded connector on the back of the monitor figure 7 Once attached it can be rotated 360 as needed to find the position which give the best reception from the camera MOUNTING THE MONITOR When choosing a location to mount the monitor figure 7 make sure the monitor is in an area that will not obstruct your vision while driving or interfere with access to any of the vehicle controls It can be placed on the windshield using the mounting arm figure 8 or clipped to an air vent figure 9 Both options use the mounting slot figure 7 on the back of the monitor 1 Temporarily place the monitor stand or clip in the location that you have chosen and route the power cable figure 10 to the vehicle s 12V power
7. re it is safe to do so Back up as slowly as possible to allow for maximum reaction time to stop the vehicle if you detect an obstacle Due to the camera s wide angle lens objects shown in the monitor are closer than they appear The picture in the monitor screen is a mirror image just like the view from your rear view mirror The camera will not show objects which have just moved out of or are just moving into the range of the camera s lens or objects that are close to either corner of the bumper or under the bumper or behind the camera s lens The camera works best in bright light and its ability to show the area behind the vehicle is diminished at night or in dark areas The vehicle s back up lights will provide light to help the camera show the area behind the vehicle at night or in dark areas Do not use the camera unless those lights are working Keep the camera lens free of water water spots snow ice and dirt so the video image remains clear and undistorted Clean the lens with a soft lint free cloth and non abrasive cleaner If the camera system image is not clear or seems distorted clean the camera lens before further use Remove the camera from its installation before washing the vehicle Use For Hitch Alignment and Towing Before towing confirm your vehicle and trailer are compatible hooked up and loaded properly and that you have any necessary additional equipment The camera will only show the relative position o
8. to the next channel after channel 4 it will return to channel 1 The camera is pre set to channel 4 Brightness figure 12 There are 6 levels of brightness To adjust the brightness press the Brightness Control button Press the button to increase the brightness after the highest level it will return to the lowest level Contrast Control figure 12 There are 6 levels of contrast To adjust the contrast press the Contrast Control button Press the button to increase the contrast after the highest level it will return to the lowest level Notice Under extreme bright light conditions the screen image may take a few seconds to automatically adjust It is best to wait until the image has stabilized before backing up Figure 6 a Figure 7 Threaded Wireless MTNA Sig Antenna Connector a lt Power Button aoa ree aS ae Figure 8 Figure 9 Mounting Arm Vent Clip Figure 10 lt 12 Volt Power Plug DC Plug Power Cable Figure 11 Power and Channel LED Indicator 3 5 LCD TFT Display 480x243 Figure 12 Wireless Channel No Function Brightness Contrast DC Input Testing the System 1 Turn the vehicle ignition to the accessory position Do not start the vehicle Notice Re locating the monitor even a small amount inside the vehicle can affect 2 Turn on the monitor and the blue status LED should come on the picture quality This device as well
Download Pdf Manuals
Related Search