Marvel Industries 8SBARE User's Manual
Contents
1. The original bill of sale deliver date or serial num ber cannot be verified Defective parts are not returned for inspection if so requested by Marvel The refrigeration equipment is not in the possession of the original end use purchaser The warranties set forth herein are the only war ranties extended by Marvel Industries Any implied warranties including the implied warranty of mer chantability are limited to the duration of these express warranties In no event shall Marvel Industries be liable for any consequential or inci dental damages or expenses resulting from breach of these or any other warranties whether express or implied Some states do not allow the exclusion or limitation of consequential damages or a limitation on how long an implied warranty lasts so the above exclu sion or limitation may not apply to you This war ranty gives you specific legal rights and you may have other rights that may vary from state to state No person firm or corporation is authorized to make any other warranty or assume any other obli gation for Marvel Industries These warranties apply only to products used in any of the fifty states of the United States and the District of Columbia To obtain performance of this warranty report any defects to Marvel Industries P O Box 997 Richmond Indiana 47375 0997 Phone 765 962 2521 NOTES W W W Marvel Industries P O Box 997 Richmond IN 47375 0997 800 428 62. wine rack configuration Interior Light and Switch The interior light makes it easy to view your wine labels and enhances the display of your collection To engage the display light press the Light button on the display panel The light will come on and stay on with the door closed To disable the display light press the Light button again The light will always come on when the door is opened Warning Alarms Your beverage center has been fitted with a Sentry system This sentry will let you know if your unit is not functioning properly for optimum wine storage Door Ajar Alarm If the door has been left open for over 5 minutes the alarm will sound and the LED will flash green This will stop as soon as the door is closed High and Low Temperature If your unit reaches temperatures outside normal operating temperatures for your set point for about one 1 hour duration an alarm will sound and the LED will flash red This will warn you that your wines have seen temperatures that may not be conducive for long term storage Power Failure If your unit experiences a power failure the LED will flash amber until the alarm is reset Reset Alarms Press the ON OFF button for approximately one second This will reset all audible and display alarms Sabbath Mode Your appliance is equipped with a Sabbath mode By activating this mode you will be disabling all displays audible alarms and lights The system will be ov
3. 644 An AGA Company 41010425 Rev B liteluxurymarvel com All specifications and product designs subject to change without notice Such revisions do not entitle the buyer to corresponding changes improvements additions replacements or compensation for previously purchased products
4. Condenser The condenser tubing inside the cabinet does not require frequent cleaning however satisfactory cooling depends on adequate ventilation over the coils Be sure that nothing obstructs the required air flow openings in front of the cabinet At least once or twice a year brush or vacuum lint and dirt from the condenser for efficient performance by unscrewing the grille on the bottom front of the cabinet Cabinet The painted cabinet can be washed with mild soap and water and thoroughly rinsed with clear water Never use abrasive scouring cleaners Interior Wash interior compartment with mild soap and water Do not use an abrasive cleaner solvent polish cleaner or undiluted detergent Glass Door Use a glass cleaner or mild soap and water and soft cloth to clean the glass door model Do not use any abrasive cleaners Door Gasket The vinyl gasket may be cleaned with mild soap and water a baking soda solution or a mild scour ing powder Light Tube Replacement WARNING DISCONNECT THE POWER CORD BEFORE ATTEMPTING LIGHT TUBE REPLACE MENT Failure to do so may result in an electrical shock that could severely injure you This product uses two 6 watt light tubes to illumi nate the interior of the beverage center The light tube is a very reliable electrical component but should it not function properly please call the deal er you purchased your beverage center from for a replacement light tube Use only an original
5. Damage This must be reported to the carrier within fifteen days Obtain inspection report from the carrier Retain the inspection report for filing the claim DO NOT RETURN DAMAGED MERCHANDISE TO THE MANUFACTURER FILE THE CLAIM WITH THE CARRIER Undercounter 8SBARE Beverage Specifications Dimensions WxHxD in 297 8 x 34 x 24 4 Weight 170 lbs Temperature 40 65 F Power Supply 115V supplied with a 15 amp plug INSTALLATION Select Location The proper location will ensure peak performance of your appliance Choose a location where the unit will be out of direct sunlight and away from heat sources Best performance will be maintained when installed within the following parameters Ideal Ambient Temperature Range Built in 65 80 F Free Standing 65 90 F Cabinet Clearance Ventilation is required from the bottom front section of the unit Keep this area open and clear of any obstructions with back wall Cord may be flush K figure 2 Electrical Plug Optional Location Cutout shown for electrical outlet which can be located in adjacent cabinetry SA Power Supply Cord with 3 prong grounding plug Grounding Type Wall Receptacle Electrical Connection Use nominal 115 volt 60 cycle AC only DO NOT USE AN EXTENSION CORD Grounding Method This product is factory equipped with a power supply cord that has a three pronged grounded plug It must be plugged into a m
6. MARVEL BEVERAGE CENTER Installation Operation and Maintenance Instructions Beverage Center 8SBARE ES eee life luxury marvel An AGA Company STARTING OUT Remove Packaging Your beverage center has been packed for shipment with all parts that could be damaged by movement securely fastened Before using be sure all packing materials and tape have been removed Important Keep your carton packaging until your beverage center has been thoroughly inspected and found to be in good condition If there is damage the packaging will be needed as proof of damage in transit Note to Customer This merchandise was carefully packed and thoroughly inspected before leaving our plant Responsibility for its safe delivery was assumed by the carrier upon acceptance of the shipment As directed on the side of your packing carton claims for loss or damage sustained in transit must be made on the carrier as follows REMINDER IT IS IMPORTANT THAT YOU SEND IN YOUR WARRANTY RECORD CARD IMMEDIATELY AFTER TAKING DELIVERY OF YOUR REFRIGERATION APPLIANCE Exterior Damage Make thorough damage notation on your delivery receipt and have driver acknowledge by signature and date Send a written request asking for an inspection report from carrier Include the name of carrier representative and the date the inspection was requested Retain inspection report and receipt for filing of a claim Concealed
7. ases condensation As outside surface humidity decreases moisture will disappear Control improperly set Interior too hot too cold Control improperly set e Faulty thermometer Relocate thermometer to center of cabinet and recheck Sentry System activated See Warning Alarms on page 4 See Alpha Control Quick Reference Temperature alarm may occur after user selected temperature set point changes in excess of 10 degrees F or during heavy usage conditions Help Prevent Tragedies Each year children die because they climb inside a The Sentry System is monitoring the duration of discarded refrigeration product get trapped inside large swings in temperature to protect your and suffocate Take precautions to prevent such contents and may alert you to this event See tragedies by removing the door taping or chaining it shut before discarding This is normal and not a fault of the appliance Reset Alarms section on page 4 OBTAINING SERVICE If You Do Need Service If you do need service contact your dealer or the manufacturer In any correspondence refer to the model number and serial number of your unit which is located on the upper left hand side of the wall liner Retain you proof of purchase You may want to record these numbers in the space below For Your Records Date of purchase Dealer s Name Dealer s Address Dealer s City Dea
8. ating grounding type receptacle in accordance with the National Electrical Code and applicable local codes and ordinances see figure 1 If the circuit does not have a grounding type receptacle it is the responsibility and obligation of the customer to exchange the existing receptacle in accordance with the National Electrical Code and applicable local codes and ordinances The third ground prong should not under any circumstances be cut or removed See figure 2 All ULL listed refrigerated products are equipped with this type of plug OPERATION Press and Hold ON OF armer F C naar aittaa Anbei OFF E Colder Light Alc Steody Amber Start Your Appliance Your appliance will start upon initial plug in The LED will flash amber upon initial plug in due to your unit being powered on at the factory to verify performance and then poweredoff The Sentry system senses a power outage has occurred and relays this information to you when you initially powerup your appliance This is normal and pressing the ON OFF button will reset this alarm function If your appliance s control has been shutoff i e unit plugged in interior lights operate display blank unit must be turned on To turn on your appliance push and hold for 5 seconds the ON OFF button located on the display panel See figure 3 Once loaded with wine bottles allow at least 48 hours for the unit to stabilize before making any adjustm
9. d other large bottles on any of the shelves except for the top shelf by removing the shelf directly above them or placing the shelf at a position allowing for proper clearance Commodities on the top rack directly under the light will be exposed to a slightly higher temperature when the light is on REMEMBER TO TURN OFF THE LIGHT WHEN IT IS NO LONGER NEEDED Keep wines that you plan to use for everyday drinking and entertaining on the front half of the racks where labels are completely visible Place wines for aging or longer term storing in the rear Roll out Shelves The roll out shelves may be pulled out approximately 14 inches to facilitate loading and retrieval Do not lean on or press down heavily on the shelves Doing so may damage the shelves or their contents Pull out shelves gently and carefully to minimize any possible item shifting To maintain stability avoid pulling out more than one shelf at any time Wine Rack Because bottles are not stacked on top of each other you can easily view and access your inventory without disturbing other bottles See figure 6 Front Bottles Necks Facing Rear Rear Bottles Necks Facing Front AAAAAL m CARE AND CLEANING OF YOUR BEVERAGE CENTER
10. ents to the initial setting Set Your Temperature Mode This product can display either Fahrenheit or Celsius To do this press the F C button on display panel Set the Controls The available temperature range of the unit is from 40 to 65 F The temperature set point is initially set in the factory at 43 F The temperature set point can be lowered or raised by first pushing the Set button on the display pad A SET icon will be displayed This icon will turn off 10 second after completing your adjustments Pushing either the Warmer or Colder buttons located on the inside of the unit on the display pad will raise or lower the set temperature by one degree F or C depending on your setting As with any refrigeration product there is a slight temperature variance at different locations within the cabinet Adjustable Temperature Control The temperature control is fully adjustable from 40 to 65 F The range allows flexibility of temperature preferences and provides the ideal wine aging storing and serving temperatures Temperature range will average between 50 to mid 60 s in the upper section and 40 to 50 s in the lower section Adjusting the Warmer or Colder buttons will affect both zones accordingly The display temperature will be reflective of temperatures in the middle section of the unit See Loading Tips and Suggestions on the next page for information regarding glass shelf and
11. equip ment light tube from your dealer or manufacturer To replace a light tube use a hex head driver remove the two hex head screws that hold a cover plate over the back section of the light tube Set the screws and cover plate aside for re assembly later Using a small flatblade screwdriver gently lever the front section of the light tube down to allow it to be pulled clear of the light housing Disconnect the two insulated electrical connectors from the cabinef s electrical cable and discard the old light tube Reconnect the electrical connector of the new light tube to the cabinet s electrical cable connectors Make sure it is secure and fully installed Carefully realign the light tube s electrical terminal back into the rear of the light enclosure channel making sure not to crimp them Gently insert the light tube along the length of the light enclosure channel Press the light tube gently into the light enclosure channel Only a small part of the light tube should project below the ceiling of the beverage center DO NOT USE A HAMMER TO FIT THE LIGHT TUBE Place the light tube terminal cover plate back in the original position on the light enclosure s flange Re use the original two screws to secure it in place Plug the beverage center into the electrical socket Check to see if the light tubes operate properly Your light tube s replacement is complete The light tubes are not covered by your warranty Replacement
12. erridden with a random control To activate the Sabbath mode press and hold the Set button while pressing the F C button 7 times within 7 seconds To disable the Sabbath mode repeat the process The Sabbath mode will deactivate after 96 hours 4 APPLIANCE FEATURES Insert Wine Bottles The wine rack roll out shelf holds ten bottles See figure 4 for typical wine bottle orientation Wine rack can be located at the middle or bottom part of the cabinet interior For red wines place wine shelf at bottom shelf position in the cabinet Then put a glass shelf in the next higher position For white and sparkling wines put the wine shelf on the middle shelf position in the cabinet Place the remaining shelves as desired See figure 5 Also there is a fixed wooden bottle cradle in the bottom step section of the cabinet Six bottles of wine may be stored there Loading Tips and Suggestions The glass shelves and fixed position wire rack are for general beverage storage such as beer and soft drinks Opened wine bottles and tall beverage containers may be stored on the glass shelf closest to the cabinet top Just lift the hinged section of the fixed position upper wire rack to provide clearance for the bottles and or containers to stand upright The wooden bottom bottle cradle may be removed for storing jug wines Just remove the two screws that secure the cradle to the cabinet floor You can store magnum bottles an
13. ler s State Zip Appliance Serial Number Model Number Date Warranty Card Sent Must be within 10 Days of Purchase How to Obtain Service Your beverage center requires little service because the best and most up to date materials equipment and quality methods are employed throughout the manufacturing process If trouble occurs during normal operation first check the troubleshooting chart on the opposite page to see if any of these simple steps may correct the problem If service becomes necessary 1 If the product is within the first year warranty period please call Marvel Customer Service at 800 428 6644 for directions on how to obtain warranty coverage in your area 2 If the product is outside of the first year warranty period Marvel Customer Service can provide recommendations of service centers in your area A listing of authorized service centers is also available at www marvelindustries com under the service and support option 3 In all correspondence regarding service be sure to give the model number serial number and proof of purchase 4 Try to have information or description of the nature of the problem how long the unit has been running the room temperature water temperatures and any additional information that may be helpful in quickly solving the problem WARRANTY Entire Product Limited One Year Parts and Labor Warranty Marvel warrants that it will supply all necessary parts and labor to repai
14. r or replace in the end user s home or office any component which proves to be defective in material or workmanship subject to the condition and exclusions stated below for a period of one year from the date of purchase by the end user Additional Second Through Fifth Year Limited Parts Only Warranty During the four years following expiration of the one year limited warranty Marvel will supply replacement parts for the hermetically sealed refrig eration system which consists of the compressor condenser drier accumulator by pass valve con necting tubing and the evaporator that are proven to be defective due to workmanship or materials subject to the conditions and exclusions below The above warranties do not cover e Shipping costs of replacement parts or returned defective parts e Customer education or instructions on how to use the appliance e Any content loss due to product failure e Removal or installation Nor do the above warranties cover failure of this product or its components due to 1 Transportation or subsequent damages 2 Use commercially or use other than normal household or small office 3 Improper installation misuse abuse accident or alteration use on wiring not conforming to elec trical codes low or high voltages failure to pro vide necessary maintenance or other unreason able use Parts or Service Not Supplied or Designated by Marvel The above warranties also do not apply if
15. tubes can be obtained from your service provider or from Marvel Industries In the Event of a Power Failure Most power failures are corrected within two hours and will not affect the unit s temperature providing you minimize the number of door openings while the power is off A gradual rise in temperature should not have any adverse effect on your wine if power is out for a longer period If it is extremely hot you may want to move your wines to the coolest location you can find until power is restored TROUBLESHOOTING Before Calling for Service Before calling for service check the trouble shooting table on this page This table lists possible problems that you can remedy without difficulty to avoid an unnecessary service call Problem Possible Causes Solutions Odor in cabinet Interior needs cleaning Noisy operation Cabinet not level e Weak floor Cabinet vibrates Cabinet not level e Weak floor Cabinet light not working Tube burned out No power at outlet Appliance will not run e ON OFF button pressed Line cord not plugged in No power at electrical outlet e House fuse blown Appliance runs too long Prolonged door openings Control set too cold Condenser needs cleaning Moisture collects inside Too many door openings e Prolonged door openings e Hot humid weather increases condensation Control improperly set Moisture collects on e Hot humid weather incre
Download Pdf Manuals
Related Search