Marvel Industries 6ORDE User's Manual
Contents
1. troubleshooting chart on the previous page to see if any of these simple steps may correct the problem If service becomes necessary 1 Ifthe product is within the first year warranty period please call Marvel Customer Service at 800 428 6644 for directions on how to obtain warranty coverage in your area 2 Ifthe product is outside of the first year warranty period Marvel Customer Service can provide recom mendations of service centers in your area A listing of authorized service centers is also available at www lifeluxurymarvel com under the service and support section 3 In all correspondence regarding service be sure to give the model number serial number and proof of purchase 4 Try to have information or description of the nature of the problem how long the unit has been running the room temperature and any additional information that may be helpful in quickly solving the problem HOUSEHOLD PRODUCT WARRANTY Entire Product Limited One Year Parts and Labor Warranty Marvel warrants that it will supply all necessary parts and labor to repair or replace in the end user s home or office any component which proves to be defective in material or workmanship subject to the condition and exclusions stated below for a period of one year from the date of purchase by the end user Additional Second Through Fifth Year Limited Parts Only Warrranty During the four years following expiration of the one year limited warr2. 8 cubic feet 33 47 F Power Supply 115V supplied with a 15 amp plug INSTALLING YOUR OUTDOOR REFRIGERATED DRAWERS Select Location The proper location will ensure peak performance of your appliance Choose a location where the unit will be out of direct sunlight and away from heat sources Best perfor mance will be maintained when installed within the follow ing parameters Unit should be operated in a properly ventilated area with ambient temperatures above 40 degrees and below 100 degrees Fahrenheit Cabinet Clearance Ventilation is required from the bottom front section of the unit Keep this area open and clear of any obstructions Adjacent cabinets and countertop can be installed on top back and sides of the unit as long as the grille and door access remain unobstructed An opening of 24 inches is required between cabinets and a depth of 24 inches Leveling Legs Adjustable legs at the front corners of the unit should be set so the unit is firmly positioned on the floor and the front is raised just enough so that the door closes easily when opened about halfway Turn leveling legs clockwise to raise unit counterclockwise to lower it Anti Tip Device A cabinet anti tip device is mounted to the back of your refrigerated drawers If your installation is a built in under counter application you do not need to apply this feature If your installation is a free standing application with no countertop direct
3. and reclamp overlay to drawer face Insert wood screws through clearance holes and tighten to secure ovelay panel Reinstall gasket into channel Make sure the corners are fully inserted Step 5 Reattach Drawer Front to Drawer Body 1 Align mounting holes on drawer body with mounting holes on drawer front Align the door liner to the front flanges by using the erasable marker alignment lines that were applied prior to removing the door from the drawer in Step 2 Reinstall Phillips head screws and washers Snug down but do not tighten fully final adjustment of drawer front will be done after reinstall ing the drawer Step 6 Reinstall the Drawers 1 Fully extend drawer slides and place drawer on slides Be sure that drawer sits evenly on both slides 2 Lock drawers into drawer slides Push drawer locks down and then back to relock the drawer into the slide Step 7 Adjust Drawer Front 1 Adjust drawer front to achieve a 1 8 inch gap from the top of the drawer front to the top of the cabinet or for bottom drawers 1 8 inch from the top of the drawer front to the bottom of the top drawer the drawer front should be centered betweent he cabinet edges 2 Fully tighten Phillips head screws to complete overlay panel installation CARE AND CLEANING OF YOUR OUTDOOR REFRIGERATED DRAWERS Condenser The condenser tubing inside the cabinet does not require frequent cleaning however satisfactory cooling depends on adequate ven
4. can be adjusted left and right or up and down by turning the knob counterclockwise Help Prevent Tragedies Each year children die because they climb inside a discard ed refrigeration product get trapped inside and suffocate Take precautions to prevent such tragedies by removing the door or by taping or chaining it shut before discarding TROUBLESHOOTING YOUR OUTDOOR REFRIGERATED DRAWERS Before Calling for Service Before calling for service check the troubleshooting table on this page This table lists possible problems that you can remedy without difficulty to avoid an unnecessary service call PROBLEM POSSIBLE CAUSES SOLUTIONS 1 Interior needs cleaning F i 1 Cabinet not level Noisy operation 2 Weak floor f f 1 Cabinet not level Cabinet vibrates 2 Weak floor 1 Tube b d out Cabinet light not working ube burned ou 2 No power at outlet 1 ON OFF button pressed 2 Power cord not plugged in Appliance will not run ee 3 No power at electrical outlet 4 House fuse blown 1 Prolonged door openings Appliance runs too long 2 Control set too cold 3 Condenser needs cleaning 1 Too many door openings o 2 Prolonged door openings Moisture collects inside f R 3 Hot humid weather increases condensation 4 Control improperly set 1 Hot humid weather increases condensation Moisture collects on out as humidity decreases moisture will disap side surface pear 2 Control improperly set I
5. the drawer fronts from the drawer bodies but the full drawer assembly is not as easy to handle as the drawer front alone 1 Remove drawer from the unit Begin by pulling out the drawer Locate the drawer lock which can be found on the outside of the cabinet slide see Figure 3 Push the back of the drawer lock forward and then down releasing the drawer from the cabinet slide see Figure 4 Repeat this on the opposite side of the drawer Lift the drawer up from the slides at a 90 degree angle to fully extricate the drawer from the cabinet see Figure 5 2 Remove drawer fronts Do this by removing the 8 Phil lips screws and washers securing the drawer front to the drawer body see Figure 6 Mark lightly with an erasable marker the position of the stainless drawer liner as it is secured to the stainless drawer before removing screws 3 Remove the gasket from the drawer front Do this by pulling the gasket out of the channel that holds it to the drawer front This will expose the clearance holes for mounting the overlay panel FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS Step 3 Size the Overlay Panel 15 19 23 06 Figure 7 Step 4 Attach the Overlay Panel to the Door 1 Set the overlay panel on drawer front face and align edges Clamp panel in position and mark pilot hole locations See Step 3 for nominal size and hole loca tions Drill pilot holes Remove panel if necessary then realign
6. MARVEL OUTDOOR REFRIGERATED DRAWERS Installation Operation and Maintenance Instructions Outdoor 24 Refrigerated Drawers 6ORDE life luxury marvel An AGA Company UNPACKING YOUR OUTDOOR REFRIGERATED DRAWERS Remove Packaging Your outdoor refrigerated drawers have been packed for shipment with all parts that could be damaged by movement securely fastened Before using be sure all packing materials and tape have been removed aaa REMINDER eep your carton packaging until your refrigerated drawers have been thoroughly inspected and found to be in good IT IS IMPORTANT THAT YOU SEND condition If there is damage the packaging will be needed IN YOUR WARRANTY RECORD CARD as proof of damage in transit IMMEDIATELY AFTER TAKING DELIVERY OF YOUR REFRIGERATED DRAWERS Note to Customer This merchandise was carefully packed and thoroughly inspected before leaving our plant Responsibility for its safe delivery was assumed by the retailer upon acceptance of the shipment Claims for loss or damage sustained in transit must be made on the retailer as follows e Exterior and Concealed Damage Any damage must be reported immediately to your retailer DO NOT RETURN DAMAGED MERCHANDISE TO THE MANUFACTURER FILE THE CLAIM WITH THE RETAILER Outdoor 6ORDE Refrigerated Drawer Specifications Exterior Cabinet Dimensions HxWxD in 34 x 23 7 8 x 24 1 4 Finished Cut Out Opening Dimensions 34 1 2 x 24 x 24 HxWxD in 170 Ibs 5
7. anty Marvel will supply replacement parts for the hermetically sealed refrigeration system which consists of the compressor condenser drier accumulator bypass valve connecting tubing and the evaporator that are proven to be defective due to workmanship or materials subject to the conditions and exclusions below The above warranties do not cover e Shipping costs of replacement parts or returned defec tive parts e Customer education or instructions on how to use the appliance e Any content loss due to product failure e Removal or installation Nor do the above warranties cover failure of this product or its components due to e Transportation or subsequent damages e Commercial use or use other than normal household or small office e Improper installation misuse abuse accident or alteration use on wiring not conforming to electrical codes low or high voltages failure to provide neces sary maintenance or other unreasonable use Parts or Service Not Supplied or Designated by Marvel The above warranties also do not apply if e The original bill of sale deliver date or serial number cannot be verified e Defective parts are not returned for inspection if so requested by Marvel e The refrigeration equipment is not in the possession of the original end use purchaser The warranties set forth herein are the only warranties extended by Marvel Industries Any implied warranties in cluding the implied warrant
8. eck the serial nameplate for the correct power supply Use only the electrical power supply specified on the serial nameplate DO NOT USE AN EXTENSION CORD Figure 1 SENTRY SYSTEM REFRIGERATION MONITOR ON OFF 38 F Set Press and Hold Start Your Appliance Your appliance will start upon initial plug in The LED will flash amber upon initial plug in due to your unit being powered on at the factory to verify performance and then powered off The Sentry System refrigeration monitor senses a power outage has occurred and relays this infor mation to you when you initially power up your appliance This is normal and pressing the ON OFF button will reset this alarm function If your appliance s control has been shut off i e unit plugged in interior lights operate display blank unit must be turned on To turn on your appliance push and hold for five 5 seconds the ON OFF button located on the display panel see Figure 2 Once products are loaded allow at least 48 hours for the unit to stabilize before making any adjustments to the initial setting Set Your Temperature Mode This product can display either Fahrenheit or Celsius To do so press the F C button on the display panel Set the Controls The available temperature range of the unit is from 33 to 47 degrees F The temperature set point is initially set in the factory at 38 degrees F The temperature set point can be lowered
9. is will warn you that your contents have seen temperatures that may not be conducive for long term storage Power Failure If your unit experiences a power failure the LED will flash amber until the alarm is reset Reset Alarms Press the ON OFF button for approximately one 1 sec ond This will reset all audible and display alarms Sabbath Mode Your refrigerated drawers are equipped with a Sabbath Mode feature By activating this mode you will be dis abling all displays audible alarms and lights To activate the Sabbath Mode press and hold the SET button while pressing the F C button four 4 times within seven 7 seconds To disable Sabbath Mode repeat the process Sabbath Mode will automatically deactivate after 72 hours FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS Figure 3 Figure 5 5 16 Phillips Head Screws Holding Drawer Front Gasket Step 1 Determine Wood Screw Requirements 1 A 8 pan head wood screw should be used to properly secure the overlay panel A total of 8 screws will be needed Use only pan head screws 3 Do not select a screw that is longer thant he wood thickness at the screw locations 4 Use recommeded pilot holes for the frame material see Table A below N Table A Pilot Hole Drill Sizes for Wood Screws Material Type Wood Screw Size Work Material 8 Step 2 Remove Drawer Fronts Note The overlay panel may be installed without remov ing
10. ly above the top of the unit you must apply this feature to prevent the unit from tipping forward when the drawers are pulled out The anti tip device is attached to the back of the cabinet Please see installation instructions supplied with the anti tip device a WARNING e Do not splash or spray water from a hose on the re frigerator Doing so may cause an electrical shock which may result in severe injury or death e This unit should not under any circumstances be ungrounded Grounding Method This product is factory equipped with a power supply cord that has a three pronged grounded plug It must be plugged into a mating grounding type receptacle in ac cordance with the National Electrical Code and applicable local codes and ordinances see Figure 1 If the circuit does not have a grounding type receptacle it is the re sponsibility and obligation of the customer to exchange the existing receptacle in accordance with the National Electri cal Code and applicable local codes and ordinances The third ground prong should not under any circumstances be cut or removed All U L listed refrigerated products are equipped with this type of plug A ground fault circuit interrupter electrical receptacle is to be used to supply electrical power to the refrigerator for outdoor applications Contact an electrician if you need to install one to supply electrical power to your outdoor refrigerator Electrical Connection Ch
11. nterior too hot too cold 1 Control improperly set 1 See Warning Alarms on page 3 2 See Sentry System Control Quick Reference 3 Temperature alarm may occur after user se lected temperature set point changes in excess of 10 degrees F or during heavy usage condi tions This is normal and not a fault of the appliance The Sentry System is monitoring the duration of large swings in temperature to protect your contents and may alert you to this event See Reset Alarms on page 4 Sentry System refrigeration monitor activated OBTAINING SERVICE FOR YOUR OUTDOOR REFRIGERATED DRAWERS If You Do Need Service If you do need service contact your dealer or Marvel Indus tries In any correspondence refer to the model number and serial number of your unit which is located on the up per left hand side of the inside wall liner Retain your proof of purchase You may want to record these numbers in the space below For Your Records Date of Purchase Dealer s Name Dealer s Address Dealer s City Dealer s State Dealer s Zip Appliance Serial Number Model Number Date Warranty Card Sent Must be within 10 Days of Purchase How to Obtain Service Your outdoor refrigerated drawers require little service because the best and most up to date materials equipment and quality methods are employed throughout the manu facturing process If trouble occurs during normal operation first check the
12. or raised by first pushing the SET button on the display pad A SET icon will be displayed Pushing either the WARMER or COLDER buttons located on the display pad will raise or lower the set temperature by one 1 degree F or C depending on your setting As with any refrigeration product there is a slight temperature variance at different locations within the cabinet Adjustable Temperature Control The temperature control is fully adjustable from the low thirties to the high forties The range allows flexibility of temperature preferences Sentry System O Power Failure Flashing Amber High Low Temp Red Figure 2 OFF Reset F Steady Amber Interior Light The upper and lower interior lights make it easy to view your food and beverages The light will always come on when either drawer is opened Warning Alarms Your refrigerated drawers have been fitted with a Sentry System refrigeration monitor This monitor will let you know if your drawers are not functioning properly for opti mum food and beverage storage Door Ajar Alarm If the door has been left open for over five 5 minutes the alarm will sound and the LED will flash green This will stop as soon as the door is closed High and Low Temperature If your unit reaches temperatures outside normal operating temperatures for your set point for more than one 1 hour an alarm will sound and the LED will flash red Th
13. tilation over the coils Be sure that noth ing obstructs the required air flow openings in front of the cabinet At least once or twice a year brush or vacuum lint and dirt from the condenser for efficient performance by unscrewing the grille on the bottom front of the cabinet Cabinet The stainless steel cabinet can be washed with either a stainless steel cleaner or a mild soap and water and thoroughly rinsed with clear water NEVER use abrasive scouring cleaners Interior Wash interior compartment with mild soap and water DO NOT use an abrasive cleaner solvent polish cleaner or undiluted detergent Care of Unit 1 Avoid leaning on the drawer fronts you may bend the door hinge or tip the unit 2 Exercise caution when sweeping vacuuming or mop ping near the front of the unit Damage to the grille can occur Periodically clean the interior of the unit as needed Periodically check and or clean the front grille and condenser coils as needed EO Gastronorm Container System For additional convenience optional Gastronorm food storage containers can be purchased from your dealer These stainless steel containers can be used to easily access smaller food items and are dishwasher safe For further information visit Marvel s website at www marvelindustries com Drawer Organizer The Drawer Organizer is designed to be fully adjustable to compensate for bottles and other items of different sizes The Drawer Organzier
14. y of merchantability are limited to the duration of these express warranties In no event shall Marvel Industries be liable for any consequential or incidental damages or expenses resulting from breach of these or any other warranties whether express or implied Some states do not allow the exclusion or limitation of con sequential damages or a limitation on how long an implied warranty lasts so the above exclusion or limitation may not apply to you This warranty gives you specific legal rights and you may have other rights that may vary from state to state No person firm or corporation is authorized to make any other warranty or assume any other obligation for Marvel Industries These warranties apply only to products used in any of the fifty states of the United States and the District of Columbia To obtain performance of this warranty report any defects to Marvel Industries PO Box 997 Richmond Indiana 47375 0997 Phone 800 428 6644 NOTES Marvel Industries PO Box 997 Richmond IN 47375 0997 800 428 6644 An AGA Company 41010649 Rev C 03 03 08 www lifeluxurymarvel com All specifications and product designs subject to change without notice Such revisions do not entitle the buyer to corresponding changes improvements additions replacements or compensation for previously purchased products
Download Pdf Manuals
Related Search