Manitowoc Ice SD1472C User's Manual
Contents
1. 3 Manitowoc KFC and Taco Bell Logo Application Instructions Manitowoc Models S600C S1470C These instructions will help the location manager or machine installer to correctly center the urethane logo on the front panel of the Manitowoc ice machine Tools Needed Philips head screw driver Contents of Kit Small packet containing alcohol prep pad Urethane logo L shaped static cling template MODEL SY0674C or SD0672C MODELS SY1474C or SD1472C Follow these instructions to remove the left section of the ice Follow these instructions to remove the ice machine front panel machine front panel from the machine from the machine 1 If your machine is on a drink dispenser remove the drink 1 If your machine is on a drink dispenser remove the drink dispenser ice bin cover dispenser ice bin cover 2 Remove the Philips head screw from lower section of the front panel 3 Pull front panel away from machine while lifting slightly 2 Remove the Philips head screw from lower section of the front panel 3 Depress pin to release front panel Pictured S600C Manitowoc Ice Inc 2110 South 26 Street P O Box 1720 Manitowoc WI 54221 1720 USA 000002851 Telephone 920 682 0161 Fax Sales 920 683 7589 Service Parts 920 683 7585 Other 920 683 7879 Rev O1 Web Site www manitowocice com 5 25 10 MODEL SY0684C or SD0672C MODELS SY1474C or SD1472C 1 Place the panel on a flat horizontal surface with the2. Manitowoc WI 54221 1720 USA 000002851 Telephone 920 682 0161 Fax Sales 920 683 7589 Service Parts 920 683 7585 Other 920 683 7879 Rev 01 Web Site www manitowocice com 5 25 10
3. stainless steel side exterior facing up Note The screw hole on the face of the panel should be in the lower right hand corner when you are facing the panel as pictured below 2 Make sure the white PVC film is removed from the front panel 3 Use the Alcohol Prep Pad found in the kit to gently clean surface of stainless steel panel focusing on the central area highlighted below Models SY1474 SD1472 Models SY0684 SD0672 4 Find the large L shaped template in the kit Remove the plastic static cling from the paper backing 5 Carefully place the L shaped static cling template in the lower left hand corner of the panel as shown in the illustration below Note Verify template rests on the top edge of the bottom molding and is aligned with left edge of the panel tere BOTTOM Models SY1474 SD1472 BOTTOM Models SY0684 SD0672 Manitowoc Ice Inc 6 Examine the urethane logo Notice that it is covered on one side by white backing paper and on the other by a thinner semi transparent masking film Peel back the solid white backing paper slowly making sure the urethane logo remains attached to the thinner semi transparent masking film This must be done very carefully as the logo has a tendency to remain attached to the solid white backing paper and the logo itself could be divided into several pieces Semi transparent film White paper Verify the entire logo remains attached to the semi
4. transparent film as you peel it back 7 Carefully place the semi transparent film and logo within the inside edges of the template making sure the edges of the film are flush with the inside edges of the template as illustrated below Note Be sure that the logo is aligned properly It is difficult to re adjust the logo once the adhesive makes contact with the stainless steel BOTTOM 2110 South 26 Street P O Box 1720 Manitowoc WI 54221 1720 USA 000002851 Telephone 920 682 0161 Fax Sales 920 683 7589 Service Parts 920 683 7585 Other 920 683 7879 Rev 01 Web Site www manitowocice com 5 25 10 When the semi transparent masking and logo are in place apply pressure against the top of the masking working out any visible air bubbles Remove the semi transparent logo masking very slowly allowing only the urethane logo to remain in the space within the template frame As the semi transparent masking is pulled back make sure no stray pieces of urethane logo remain attached to the semi transparent masking If this occurs slowly lower the masking and press firmly against it to make sure the remaining piece sticks to the stainless steel Remove the template from the surface of the stainless steel front panel Reattach the stainless steel front panel to the ice machine If the machine is on a beverage dispenser re attach the drink dispenser ice bin cover Manitowoc Ice Inc 2110 South 26 Street P O Box 1720
Download Pdf Manuals
Related Search