Magma A10-1225 User's Manual
Contents
1. ige Solenoid To othbr LPG f shut off Gas Regulator TROUBLE SHOOTING GUIDE Problem Burner will not light with igniter Possible Cause Igniter electrode covered with grease or residue Igniter electrode too far from burner Igniter electrode wire loose or disconnected Wire is shorted causing spark from wire before electrode No spark being generated Possible Solution Clean igniter electrode Adjust electrode until proper spark appears see page 5 Reconnect wire between igniter amp electrode see page 5 Call Magma Call Magma Burner will not light even with match No gas flow Obstructed gas flow debris or spider webs in burner tube Check fuel level refill cylinder or replace canister Clean valve orifice and burner check all lines see page 6 Flare up Excessive cooking temperature Grease and or residue build up Excessive fat in meats Excessive oils in marinades Operate only on low when lid is closed Reduce flame level Leave lid open Use water spray to cool Clean components Trim fat from cuts of meat before grilling Use non oil based marinades Yellow sooty flame Obstructed gas flow debris or spider webs in burner tube Check and clean valve orifice and burner see page 6 Blow out Flame too low Wind directly on burner Obstructed gas flow Increase flame Block wind when opening lid Clean burner or valve2. LPG Propane Systems use Magma Type 3 High Output Low Pressure LPG Control Valve and Magma Low Pressure LPG Hose Kit For on board CNG Natural Gas Systems use Magma Type 4 High Output Low Pressure Natural Gas Control Valve See Magma website for replacement part numbers and valve applications Ld www MagmaProducts com O y Thermometer Warming Rack ee ae Lid Lock Grill Grates Radiant Plate ang Burner Liner Outer Shell Match Light y Valve Chamber Hole eae Wa Control Valve Regulator Mount Eh Type 1 High Support Pad cun Output Shown Slide Out p aan Grease Tray 3 Piezo Igniter OPERATING PROCEDURES OPERATE ONLY ON LOW WHEN LID IS CLOSED ALWAYS OPERATE WITH GREASE TRAY IN PLACE WARNING Do not overheat grill Magma Grills do not require pre heating Stainless Steel loses anti corrosive characteristics when subjected to extreme heat Most grilling is done on low temperature with the lid closed If medium or high heat is required grill with lid open LIGHTING INSTRUCTIONS Open lid during lighting Depress Knob and rotate counter clockwise to the HIGH flame 6 position Push Piezo Igniter Visually confirm ignition through match light hole Turn knob to adjust flame If grill does not light repeat process MATCH LIGHTING INSTRUCTIONS Open lid during lighting Depress knob and rotate counter clockwise to the HIGH flame 6 position Hold match or gas flam
3. 86 Prior to installing valve become familiar with the valve function and graphics on valve knob Never force the knob Always turn or push gently Turn control valve to lock 0 and install gas canister being careful not to cross the threads Check for leaks prior to use Position valve with gas bottle as shown A Gently insert valve stem into valve chamber while rotating until valve stem key aligns with valve chamber lock detent allowing valve to fully insert Rotate gas canister down and away so knob faces you B or straight up C depending on application A MOUNT HARDWARE Fasteners are supplied for both Single Mount and Dual Mount grill mounting options See Magma Catalog or Website for best mount selection tf 7 N 4 g N yo TF gt n SS ih 7 gt SS e a mi a gt Dae a gt Ss gt D a a gt lt gt o o s las Single mount through bolt Dual mount applications applications 4 Carriage bolts amp lock nuts Only 4 bolts 4 Carriage bolts amp lock nuts required for grill mounting Place bolts 2 per side diagonally from each other as shown o Tt Single mount non through bolt a F lt applications including Style 1 Levelock ae 4 Hex head bolts amp lock washers Carriage bolt Hex head bolt amp lock nut amp lock washer ON BOARD FUEL SYSTEMS APPLICATION For on board
4. OWNER S MANUAL MOMTERE by MAGMA Gourmet Series Marine Gas Grill Model A10 1225 pen E a _ ons m For questions regarding performance assembly STOP operation parts or returns contact the experts Before at MAGMA by calling TOLL FREE IN U S A AND returning this CANADA 1 800 86 MAGMA item to the dealer 7 00 a m 5 00 p m Pacific Time Monday thru Friday or e mail us at mail MagmaProducts com M MAGMA Read all instructions before operating Save manual for future reference IMPORTANT SAFETY WARNINGS READ ALL INSTRUCTIONS BEFORE OPERATING USE OUTDOORS ONLY DO NOT USE THIS APPLIANCE INSIDE THE BOAT OR ANY ENCLOSED SPACE GRILLS RADIATE HEAT CLEARANCE FROM COMBUSTIBLES 24 SIDES AND BACK NEVER USE UNDER AWNINGS PATIO COVERS ETC USE PROPANE GAS ONLY FUEL STORAGE SHOULD BE IN COMPLIANCE WITH THE AMERICAN BOAT AND YACHT COUNCIL ABYC STANDARDS A 1 9 MARINE LIQUIFIED PETROLEUM GAS LPG SYSTEMS FOR NATURAL GAS APPLICATION CONTACT MAGMA ALWAYS LIGHT GRILL WITH LID OPEN NEVER LEAVE HOT GRILL UNATTENDED USE HOT PAD WHEN HANDLING ALWAYS TURN GRILL OFF AFTER USE Each Magma Gas Grill is individually fire tested before it leaves the factory For this reason the burner on your grill may be slightly discolored INSTALLATION INSTRUCTIONS CONTROL VALVE REGULATOR Uses standard 1 lb disposable propane canisters DOT 39 NRC 228 2
5. Y amp RE ASSEMBLY Lift radiant plate up amp out of left slot see B and remove by sliding it out of right slot see C Remove burner screw see B and remove burner Check burner for grease residue or spider webs that may obstruct gas flow CAUTION WHEN REPLACING BURNER CUT SLOT IN BURNER MUST FACE DOWN To remove liner from outer shell you must disconnect the electrode wire see D First remove the two screws on valve chamber see D and remove the cover plate Gently pull wire off connector see D It is not necessary to remove electrode from liner Remove Lid and liner by removing hinge screws and lock nuts with 3 16 hex key wrench supplied and 1 2 wrench or pliers CAUTION LOCK NUTS MUST BE INSTALLED WITH LOCKING INDENT MARKS SHOWING see E IMPROPER INSTALLATION WILL DAMAGE THE HINGE SCREW AND LOCK NUT Lift liner out of outer shell by lifting up on liner lip on back side of liner see F When replacing liner be sure top lip of liner installs over top edge of outer shell start with corners of lip and work in Inspect burner remove any obstructions Clean as indicated in Maintenance page 6 To re assemble reverse the procedure Disconnect wire i 8 Screws Burner screw A a Liner Lip Liner Outer Shell Locking Indents MAINTENANCE About Stainless Steel Stainless steel exposed to prolonged periods of high heat will change color and texture Magma grills require no preheat
6. ase must be returned postage prepaid to Magma Products Inc We suggest that you keep your purchase receipt as we may require reasonable proof of purchase In the state of California only if refinishing or replacement of the product is not commercially practicable the retailer selling the product or Magma Products Inc will refund the purchase price paid for the product less the amount directly attributable to use by the original consumer prior to the discovery of the nonconformity In addition in the state of California only you may take the product to the retail establishment from which it was purchased or to any retail establishment selling this product in order to obtain performance under this warranty All implied warranties including the implied warranties of merchantability and fitness for a particular purpose are limited in duration to the express warranty periods specified herein for the parts described herein Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you Neither Magma dealers nor the retail establishment selling this product has any authority to make any warranties or to promise remedies in addition to or inconsistent with those stated above Magma s maximum liability shall not exceed the purchase price of the product paid by the original consumer Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation o
7. e long lighter up to the match light hole Visually confirm ignition through match light hole TO REDUCE FLARE UP Empty and clean grease tray prior to each use Trim excess fats from meat Use non oil based marinades Reduce heat Use water spray directly on flare ups NOTE Before lighting lid lock must be positioned not to engage Open lid and turn lock to locked position or bring lock latch up to handle in open Position and flip lock actuator back onto handle PRACTICAL HINTS Before lighting your grill be sure that Grill is secure and properly mounted Internal components and grease tray are clean and correctly positioned You have plenty of gas in the canister Gas canister is attached properly and there are no gas leaks Lid lock has been set not to engage You have a water spray bottle handy to cool a hot grill or stop any flare ups STOWING TIPS Always disconnect the fuel canister from the valve prior to stowing Stow the valve in a clean dry area to protect from corrosion to valve Always store propane in a sealed propane storage locker that allows leakage to vent overboard or use Magma A10 210 Propane Storage Tote Never stow below decks 4 ELECTRODE SPARK ADJUSTMENT CAUTION Spark can cause small shock Do not leave fingers on or near electrode wire while engaging igniter Electrode wire should be approximately 1 8 from gas exit hole in burner Carefully adjust wire if required DISASSEMBL
8. ing Not preheating will keep your grill cooler and greatly extend the life and beauty of your grill Texture and color change is normal on interior components and will not affect the products operation or performance Exterior Stainless Steel Components Cleaning the exterior surface after every use will help prevent discoloration Use soapy water with a soft cloth or sponge Rinse thoroughly with fresh water and dry We recommend covering the grill between uses Optional covers are available from Magma retailers or direct from Magma CAUTION ABRASIVE PADS OR CLEANERS WILL DAMAGE THE FINISH Interior Components Remove heavy residue from grill and empty grease tray between each use We recommend complete disassembly and cleaning at least once a year depending on amount of use see page 5 and always prior to long term storage For burnt on residue we recommend Easy Off brand Oven amp Grill Cleaner If cleaner is used on liner or lid complete disassembly is recommended to remove any cleaner residue left between components Wash all components with soapy water after using cleaner CAUTION AVOID CONTACT OF IGNITER AND ELECTRODE WIRE AND WIRE CONNECTORS WITH OVEN CLEANER Grill Grates Clean with brass wire brush while grill is warm Use Oven amp Grill cleaner for burnt on residue Wash with soapy water and dry prior to storage Ceramic Electrode Located just beside the burner it should be kept clean of grease and debris Be careful not to da
9. mage the ceramic insulation or bend the wire See page 5 for electrode spark adjustment Control Valve All valves are set and tested at our factory Do not attempt to adjust or disassemble the valve in any way Call Magma if you suspect it is not adjusted properly Clean valve with a cloth and remove any debris obstructing the gas outlet orifice using a pin or needle Repair Replacement Parts See Magma Website for a complete list of Repair or Replacement Parts www MagmaProducts com USING GRILL WITH ON BOARD LPG PROPANE SYSTEMS Magma On Board LPG Propane Valves Er QY coume and Hose Kits allow Magma Grills to be San Laa installed within a boats existing on board pre regulated low pressure LPG Propane system Use only Magma Type 3 Low Pressure LPG Propane Valves See our Valve Application Guide at www rr e A Align vaive stem key SL to valve chamber lock detent and rotate Gourmet Gas Grill Typical Marine amp Type 3 MagmaProducts com for correct valve R V Application y In North America use Magma A10 225 LPG 10 Hose Kit in conjunction with Cylinder Valve Type 3 Valve Outside North America check your local dealer for proper hose and fittings A primary shutoff valve supplied with A10 225 hose kit must be used with this Propane LPG BE erage opines control valve at point of connection into Hose Kit your system This allows shut off of gas w supply to hose leading to grill
10. orifice see page 6 Contents xX 4 A 1 3 16 Hex key wrench for lid removel B Pack of 4 1 4 20 x 5 8 hex head screws and internal lock washers for Levelock single mount application C Pack of 4 1 4 20 x 5 8 carriage bolts and lock nuts for dual mount and single mount applications and table legs Magma Products Inc guarantees this gas grill to be free from defects in materials or workmanship to the original consumer This guarantee is for the periods herein specified when used under normal and reasonable conditions one I year from the date of original purchase This warranty does not include the cost of property damage or any inconvenience due to the failure of the product Nor does it cover damage due to misuse abuse accident or damage resulting from transportation of the product Nor does it include damage resulting from the commercial use of this product If the product fails to operate due to a defect in materials or workmanship during the warranty period the defective part will be repaired or replaced at Magma s option If you wish to obtain performance under this limited warranty you should contact Magma s Customer Service Department via telephone at 562 627 0500 or 800 86 MAGMA or via e mail at mail MagmaProducts com or via U S Postal Service mail at Magma Products Inc attention Customer Service 3940 Pixie Ave Lakewood CA 90712 The defective part along with proof of purch
11. r exclusions may not apply to you The warranty gives you specific legal rights and you may also have other rights which vary from state to state MAGMA and the Magma logo are registered trademarks of Magma Products Inc Monterey is a trademark of Magma Products Inc Patent pending CALIFORNIA PROPOSITION 65 WARNING The burning of gas cooking fuel generates some by products which are on the list of substances which are known by the State of California to cause cancer or reproductive harm California law requires businesses to warn customers of potential exposure to such substances To minimize exposure to these substances always operate this unit according to the use and care manual ensuring you provide good ventilation when cooking with gas MIMAGMA Magma Products Inc 3940 Pixie Avenue Lakewood CA 90712 USA Phone 562 627 0500 e mail mail MagmaProducts com www MagmaProducts com 83 1225 1105
Download Pdf Manuals
Related Search