Lux Products TH10 (discontinued) Instruction Manual
Contents
1. V LVULA DEGASO CALENTADOR NOTAS DEL DIAGRAMA DEL CABLEADO Si reemplaza un Honeywell TM 11 desprenda el cable R Conecte el cable B a la terminal RH Si reemplaza el termostato que tiene un cable de reloj marcado como tipo C desprenda este cable y no lo conecte a este termostato Si los cables Y y C est n presentes entonces C es un cable normal despr ndalo y no lo conecte a este termostato e Si un cable B en su sistema es un cable normal despr ndalo y no lo conecte a este termostato2. In The Dark Dial Numbers Soft Rubber Set Temperature Ring Large Easy To Use Mode Switches Light Button Mode Switch Set Temperature Ambient Room Set Temperature Temperature Selector Ring US Patent USP D471 572 SELECTING A LOCATION On replacement installations mount the new thermostat in place of the old one unless the conditions listed below suggest otherwise On new installations follow the guidelines listed below 1 Locate the thermostat on an inside wall about 5 ft 1 5m above the floor and in a room that is used often 2 Do not locate where air circulation is poor such as in a corner or an alcove or behind an open door 3 Do not install it where there are unusual heating conditions such as in direct sunlight near a lamp television radiator register or fireplace near hot water pipes in a wall near a stove on the other side of a wall 4 Do not locate in unusual cooling conditions such as on a wall separating an unheated room or in a draft from a stairwell door or window Do not locate in a damp area This can lead to corrosion that may shorten thermostat life If painting or construction work has yet to be completed cover the unit completely or do not install it nu TOOLS REQUIRED e 1 Phillips screwdriver Drill with 3 16 in 4 8mm bit 1 Slotted screwdriver Wire Stripper Cutter NOTE Review the type of wiring configuration that your system requires prior to r
3. INSTALLATION AND OPERATING INSTRUCTIONS EcoStat TH10 Heating Only Mercury FREE Manual Thermostat 52084 LUX PRODUCTS CORPORATION Mt Laurel New Jersey 08054 USA http www luxproducts com IMPORTANT Please read all instructions carefully before beginning installation and save for future reference Before removing any wiring from your existing thermostat the wires must be labeled with their terminal designations Ignore the color of the wires since they may not comply with any standard Thank you for your confidence in our product To obtain the best results from your investment please read these instructions thoroughly You should become fully acquainted with this thermostat before installing it for usage Follow the installation procedures carefully and one step at a time This will save you time and minimize the chance of damaging either the thermostat or the systems that it controls These instructions may contain information beyond that required for your particular installation Please save these instructions for future reference COMPATIBILITY This mechanical thermostat can be used with most 2 wire single stage 24 volt gas or oil heating systems It cannot be used with cooling systems heat pumps electric furnaces 3 wire zone valves line voltage 120 240 volt heating systems or Millivolt systems Ask your dealer for other LUX thermostats to control those systems FEATURES Push Button Back Light Glow
4. N AND WIRING SCHEMATICS ECOSTAT TH10 HEATING ONLY SYSTEM WIRING WIRING DIAGRAM NOTES If replacing a Honeywell TM 11 tape off the R wire Connect the B wire to the RH terminal If replacing a thermostat that has a clock wire labeled as C tape off this wire and do not connect it to this thermostat f Y and C wires are both present then C is a common wire tape off this wire and do not connect it to this thermostat e f a B wire in your system is a common wire tape off this wire and do not connect it to this thermostat TH10 FRANCAIS SCH MAS D IDENTIFICATION DES FILS ET DU C BLAGE CABLAGE DU SYSTEME DE CHAUFFAGE SEULEMENT ECOSTAT TH10 pre e m W Ly ooo NOTES DU DIAGRAMME DE CABLAGE e Si vous remplacez un mod le Honeywell TM 11 couvrez le fil R Branchez le fil B la borne RH e Si vous remplacez un thermostat fil d horloge portant la mention C couvrez ce fil et ne le branchez pas ce thermostat e Si vous avez les fils Y et C alors le C est un fil commun couvrez le et ne le branchez pas ce thermostat e Si un fil B de votre syst me est un fil commun couvrez ce fil et ne le branchez pas ce thermostat TH10 ESPANOL IDENTIFICACI N DE CABLES Y DIAGRAMAS DE CABLEADO p es es es es i CABLEADO DEL SISTEMA S LO PARA CALEFACCI N ECOSTAT TH10
5. VdN09 sulajs g Duijoo e ug as 104 JON suieis s YOAIIIN e sa2eun 2u199 3 AOvZ 0ZL 9De3oA our e nod Jasin y 31riarivdiN03 seduiodouliau e JOANNA Sauue1s S o uaulassipioJJJ op souigiS g e senbume g sesieulno J e Q c gt c 2 5 E c a 2 ro co o e wm lt E a 3 2 e ex D e E za S 3 D o az a c c a e x o S 3 o o D D e e EE o o o SI Z apneyo neo p sanbiue29uio04129 9 sauJg1s S e nod Jasijyn sed au y ze ne no eju e abeyneyo ap sauigis s aDejineu e juauig nas A pz efejneuo e E 3 5 o 35 2 e E eo pens n2 Q N A e e MERCURY WARNING AND RECYCLING NOTICE Mercury is considered to be a hazardous material If this product is replacing a thermostat that contains mercury Opeuolo IPUOIE ale 9p SBLUAISIS o SONIOA pc ua 1esn ON 9p ugio2ejo e ap ejuaureos sonjo 0pZ 0Z L eaul op LYON e sajqeo e ap ajuai eo enfe Jojeo ap sequiog e u09 OSN ns Eleg avariaivdio3 in a sealed tube contact your local waste management authority for instructions regarding recycling and proper disposal It may be unlawful in your state to place it in the trash SORJOAII 9D SEUIBISIS o 9p sooiuoJplu SBLUAISIS o Se qeo z ap ajuaieo enfe 9p SODIUOIPIY Seulajsig e o9 0418d o seb e ugi22ejo e 9p seugjsis ugio9ej9 e e SeUl9jsIS SO 9p PLOACW e 92084 TH10 ENGLISH WIRE IDENTIFICATIO
6. emoving your old thermostat or its wiring connections REMOVAL OF OLD UNIT 1 Turn OFF the electricity to all heating and cooling components Do not turn the electricity back on until all work is completed 2 Remove the cover and front portion of your old thermostat to expose the wiring connections 3 Write down the letters printed near each wire terminal that is used and the color of the wire that is connected to it Using the enclosed labels attach a label to each of your wires so that the letter matches the marking on your existing thermostat 4 When they are all labeled carefully remove the wires one at a time making sure that they do not fall back inside the wall Do not allow any of the bare wire ends to touch each other or any parts on the thermostat 5 Loosen all of the screws on the old thermostat and remove it from the wall MOUNTING Strip insulation leaving 3 8 in 9 5mm bare wire ends and clean off any corrosion Fill wall opening with non combustible insulation to prevent drafts from affecting the thermostat The Wall Trim Plate is optional however its usage is recommended Remove the front trim ring from the thermostat by pulling it straight outwards If there are no existing mounting holes that are able to be reused hold the Trim Plate level against the wall with the UP markings up and mark the outer two oval mounting holes on the right and left NOTE if you are not using the Trim Plate you can st
7. icipator setting If you cannot find either of these numbers set it to 6 initially to start with During heating season your furnace should operate about five times an hour If adjustments are necessary move heat anticipator pointer slightly and recheck A lesser value will cause your heater to cycle more frequently and a larger value will cause it to cycle less frequently OPERATION There is a mode switch on the front that has two positions HEAT and OFF In the winter set the system switch to HEAT to control your heating system In the spring summer and fall or when the windows are open you can set the switch OFF In HEAT mode turn the front thermostat dial to the desired temperature setting BACKLIGHT This thermostat has an illuminated panel to assist in reading the temperature while in low light conditions While in HEAT mode press and hold the button on the top of the thermostat The backlight will not operate while the thermostat is in OFF mode TECHNICAL ASSISTANCE If you have any problems installing or using this thermostat please carefully and thoroughly review the instruction manual If you require assistance please contact our Technical Assistance Department at 856 234 8803 during regular business hours between 8 00AM and 4 30PM Eastern Standard Time Monday through Friday You can also receive technical assistance online anytime day or night at http www luxproducts com Our web site offers you answers to the most comm
8. ill mark the holes for the thermostat using the two small inner holes on the right and left of the Trim Plate which line up with the thermostat mounting holes 6 If you are mounting the base to a soft material like plasterboard the screws alone may not hold Drill a 3 16 in 4 8mm hole at each screw location and insert the plastic anchors provided into the wall If you are mounting to wood or similar substance the screws may be used alone without the plastic anchors 7 First feed the wires through the large middle hole in decorative wall plate if used and then through the square lower hole near the bottom of the thermostat s Sub Base 8 Referring to your earlier notes from removing your old thermostat and the electrical diagrams in this manual attach the wires to the terminal screws Make sure bare metal wires do not touch each other The wire connector screws on the Sub Base may need to be loosened prior to inserting any wires When all wiring is complete ensure that every screw is securely tightened Cc1 Rc05 n 2009 LUX PRODUCTS CORPORATION ALL RIGHTS RESERVED Sub Base Orientation Marks 3 Mounting Holes 9 Insert the two longer mounting screws provided through the right and left Trim Plate screw holes and thread each screw into the mounting holes into the wall or the plastic screw anchors 10 Carefully push all excess wire back into the wall Align the thermostat sub base with the decorative wall p
9. late by using the 3 alignment pins and holes molded into the back of the subbase and Trim Plate Attach the Sub Base to the Trim Plate using the two smaller mounting screws provided Thread these two small screws into the single inner holes in the Trim Plate 11 Now that the Sub Base is mounted align the front portion of the thermostat with the Sub Base using the Light Button and the cutout for it in the Sub Base While holding the thermostat in place against the Sub Base carefully and evenly tighten the 3 silver captive screws that are held in place inside the front of the thermostat assembly WIRING INFORMATION Complete heating and or cooling system wiring can be found in the WIRE IDENTIFICATION AND WIRING SCHEMATICS section of this instruction sheet The schematics shown provide component information for brand new installations or for unreferenced wires The only item that will need to be tailored to your system is the Heat Anticipator If you are Heat replacing an old mechanical thermostat find the Anticipator Anticipator setting on the old thermostat and set Adjustment the new thermostat to the same value Do this by carefully sliding the silver metal pointer shown here over desired number printed on the Anticipator scale If an old Anticipator setting cannot be determined look on the gas control valve on your furnace and find either the Anticipator Value or a Current Rating This will be the value to use for the Ant
10. on technical questions and also permits you to email your questions to our technical support staff at your convenience WARRANTY Limited Warranty If this unit fails because of defects in materials or workmanship within three years of the date of original purchase LUX will at its option repair or replace it This warranty does not cover damage by accident misuse or failure to follow installation instructions Implied warranties are limited in duration to three years from the date of original purchase Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you Please return malfunctioning or defective units to the location from which the purchase was made along with proof of purchase Please refer to TECHNICAL ASSISTANCE before returning thermostat Purchaser assumes all risks and liability for incidental and consequential damage resulting from installation and use of this unit Some states do not allow the exclusion of incidental or consequential damages so the above exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state Applicable in the U S A and Canada only sulajs S 1916A 10H 21UOJp H BIM sulals g 1936 JOH DIUOIPAH BM Z sulas S Dune IQ 10 SEY H L e ap s wu3 s s sap pednid e7 e SWS S JUQ 1e9H Aye ISOIN e ug esf 104 sduing 1e9H e ALII 11L
Download Pdf Manuals
Related Search