Logitech 700e User's Manual
Contents
1. or the use publication or distribution of image and or audio recordings are prohibited or restricted by country state and local laws Be sure to comply with the laws in your country state and locality when using Logitech Alert products and services RECOMMENDATION Mount the Outdoor Camera under an eave or other overhang so that it is not exposed to direct 1 Run Logitech Alert Commander Before you begin the installation read all instructions Logitech Alert Master System required 1 Be sure that Logitech Alert Commander sotware is running on the PC before beginning installation of camera Power Supply Install Note The power supply unit is weatherproof and can be installed outdoors Use these tips to ensure reliable power supply usage Make sure the outdoor outlet is weatherproof Do NOT place on the ground 1 Do NOT plug the power supply into a surge protector or power strip as they interfere with the cameras Surge protectors are built in to the power supply and protect the cameras 2 Do NOT plug the power supply into the wall so that it lays horizontally or flat 3 Do NOT mount the power supply upside down Keep the cable connector port on the bottom CAUTION If left in sunlight surface may be hot to the touch FAQs Where can find more information Commander Help You can press the F1 key from any screen in the Alert HELP Commander to access the online2. Getting started with o z Logiteche Alert 700e inaite di 50e Logitech Mer AS Mane amp Support Guide 1 Logitech Outdoor Camera 4 Mounting accessories 2 Camera power supply 5 microSD card adapter 3 Power supply cable yellow tips 6 System Requirements Guide Add On Camera Le a 2 Plug in Your Camera When prompted to connect your camera 2 Unscrew the hatch from the power supply 2a Plug the yellow cable into the power supply port 1 Unscrew the hatch from the back of the camera and lift 2b Screw the hatch firmly in place la Plug the yellow cable connector into the port 2c Mount the power supply unit to the wall 1b Screw the hatch firmly in place 2d Plug the power connector into the plug slider and plug the power supply into an outlet e Shortly after connecting your camera will appear in Alert Commander software You can now move the camera to its desired location Wall Ceiling Mounting Instructions The wall mount allows you to easily fasten your camera to a wall post 2 Assemble the mounting arm and attach it to the base overhang or other surface 3 Attach the camera to the mounting arm 1 Start by pre drilling holes into the base surface and then fastening the mouting base with the included screws Legal Warning Certain uses of security camera products and audio devices such as employee monitoring surreptitious viewing and recording of images and or audio
3. Help system Knowledge Base Troubleshooting help is available at www logitech com support Customer Support Call 1 888 469 4543 d Refer to System Requirements Guide Logitedn tert 100e 50e System Requirements amp Support Guide Reading the Diagnostic LEDs Motion LED How do know the camera is recording Camera is ready to record Red Camera is recording Red blinking Turning Off Motion and Diagnostic LEDs You can turn off the motion and diagnostic LEDs in the Settings gt Camera dialog See F1 Help for instructions www logitech com 2010 Logitech All rights reserved Logitech the Logitech logo and other Logitech marks are owned by Logitech and may be registered All other trademarks are the property of their respective owners Logitech assumes no responsibility for any errors that may appear in this manual Information contained herein is subject to change without notice 620 002016 rev005 What do do if need a longer power supply cable Logitech CAT 5e cables have been specially designed to create a weatherproof seal when attached to the camera and power supply We do not recommend using after market cables Longer cables are available for purchase at www logitech com dvs Accessories Want to see more FAQs Go to www logitech com security support Camera Diagnostic LED Which LED colors indicate camera is working Connected to Internet Green Connec
4. set Instructions Camera Diagnostic LED Which LED colors indicate camera is not working g Camera boot up failed Red blinking ot microSD card read write failure No microSD lt 1 Card Alternating Red Yellow blinking See Camera Reset Instructions for assistance Camera Reset Instructions Insert a paper clip into the reset hole located on the back of the camera and press gently and then release If the camera does not appear after reset go to Settings gt Cameras gt Add Find gt Find Cameras If the camera still does not operate contact technical support Resetting the camera will not delete video recorded on the microSD card Power Suppy Diagnostic LEDs Power Supply Status LED What do these LEDs tell me What do these LEDs tell me Traffic and data is flowing Green Linkto Power Supply Green Connection with Ethernet LAN Shows network traffic Blue Yellow microSD Logo is a trademark of SD 3C LLC
5. ted to Alert Commander Purple Connected to Alert Commander amp Internet Blue Upgrading Firmware White Camera in standalone mode Yellow O 00000 Not connected to Alert Commander or Internet Light Blue Using the microSD card adapter NOTE Unplug the camera before removing replacing or upgrading your microSD card microSD card comes pre installed To review the video on the microSD card we recommend you using Logitech Alert Commander To review the video on the microSD card without Logitech Alert Commander 1 Open the hatch on the bottom of the camera and remove the microSD card from its port 2 Plug the microSD card into the adapter 3 Plug the adapter into the PC s SD card slot e View video recordings using the free Apple QuickTime player or other player that supports H 264 video playback To download QuickTime visit http www apple com quicktime download Q microSD card must be installed in the camera for recording to occur Troubleshooting camera connection What if camera video disappears 1 Test another outlet for your camera perhaps one closer to your PC 2 Verify that the camera power supply and the network bridge are plugged directly into a power outlet and not a power strip 3 Check firewall settings or press the F1 key in Commander Software for additional help 4 Go to Settings gt Cameras gt Add Find gt Find Cameras 5 Reset the camera See instructions in Camera Re
Download Pdf Manuals
Related Search