Lightolier 7589AZ User's Manual
Contents
1. INSTRUCTION SHEET NO IS 7589 Nae INSTRUCTIONS FOR LYTESPAN ATTACHMENT FITTING a NW R0681 SILVERED CONTACT A CORD PENDANT MOUNTING A BRASS CONTACT NZ pA supports up to 10 Ibs E 1 Unscrew LEVER Remove PLUG ASSEMBLY HOUSING 4 af INSERT from attachment HOUSING See Fig 1 EEGI SA i ea uenea 2 See WIRING PROCEDURE below LEAD B STEM MOUNTING USING 1 2 0 D TUBING S supports up to 25 Ibs Weed 1 Unscrew LEVER STRAIN RELIEF CAP and KNURLED CONNECTOR RING Remove PLUG ASSEMBLY HOUSING INSERT from attachment HOUSING GREEN GROUND 2 Use STEM TUBING with 4 18 pipe thread CEAD 34 long not supplied Screw KNURLED RING onto STEM TUBING See Fig 1A H LEVER 3 Insert STEM TUBING into attachment 4 J HOUSING and screw on LOCKNUT until secure 4 Tm Tighten KNURLED RING to lock in place 4 See WIRING PROCEDURE below on C CHAIN MOUNTING a supports up to 25 Ibs FOGKAUT 1 Unscrew LEVER and STRAIN RELIEF CAP KNURLED RING paste Remove PLUG ASSEMBLY HOUSING INSERT from SET SCREW attachment HOUSING Da e FIXTURE 2 Replace STRAIN RELIEF CAP with 14 18 CHAIN LOOP CORD not supplied See Fig 1B FIG 1 3 See WIRING PROCEDURE below CHAIN Ne D WIRING PROCEDURE oe ee ae 1 Remove 2 of outer insulation from FIXTURE CORD when required and strip conductor ends See Fig 1 2 insert FIXTURE CORD through attachment housing Fasten BLACK WI2. RE to LONGER BRASS CONTACT and WHITE WIRE to SHORTER SILVERED contact For STEM 3 conductor cord splice GROUND LEADS with wire MOUNTING pour connector If the GROUND LEAD from the attachment FIG mS HOUSING is not used leave wire connector on See Fig 1 1A FIG 1B CAUTION OBSERVE POLARITY WHEN ie D FASTENING WIRES BEND WIRES AROUND CONTACT SCREW IN CLOCKWISE DIRECTION GROOVE 3 Pull FIXTURE CORD back through attachment HOUSING and Z Af push HOUSING INSERT and PLUG ASSEMBLY into calf h SL neuer HOUSING silvered contact in PLUG ASSEMBLY facing o grooved side of attachment HOUSING Push ground leads into area between SPRING section Fig 2 4 Allow fixture cord to extend into attachment HOUSING by Ye and tighten PLASTIC SET SCREW Fig 2 CAUTION TIGHTEN ENOUGH TO SUPPORT Seer ASSEMBLY 5 Screw LEVER into PLUG ASSEMBLY PLASTIC SET SCREW STRAIN RELIEF CAP FIG 2 i IG HTOI mm pap SECAUCUS NEW JERSEY 07096 0508 es E aiiz i2 MONTREAL QUEBEC CANADA 19 7589 INSTRUCTIONS FOR ATTACHING LYTESPAN R0681 ATTACHMENT FITTING 1 Align BEAD on LYTESPAN TRACK and GROOVE in attachment FITTING before inserting into LYTESPAN TRACK See Fig 1 if BEAD is NOT aligned a potential hazard may result LYTESPAN TRACK TURN KNOB 2 Unscrew the TURN KNOB partially and position LEVER as shown in Fig 1 BEAD LEVER 3 To attach attachment FITTING squeeze BUTTON and TURN KNOB insert into LY
3. TESPAN TRACK and release Tighten TURN KNOB This GROOVE holds attachment FITTING to LYTESPAN TRACK mechanically Turn LEVER to make electrical connection See Fig 2 BUTTON FITTING FIG 1 4 To shift fixture location on the LYTESPAN TRACK loosen TURN KNOB slightly release LEVER and slide to new position 5 To remove fixture reverse the procedure in 3 push TURN KNOB in and allow attachment FITTING to disengage 6 Fixture can be left on LYTESPAN TRACK when not in use by turning LEVER to disconnect electrically INSTRUCTIONS FOR CONVERTING LYTESPAN ATTACHMENT FITTING TO OPERATE ON 2 CIRCUIT LYTESPAN TRACK BLACK SPACER MOVABLE BRASS CONTACT NOTE To insure proper operation of Lytespots on Two Circuit Lytespan Track the BLACK SPACER supplied must be used at all times on the plug assembly The BLACK SPACER is not used when operating Lytespots on Single Circuit Track LOWER CIRCUIT FIG 3 Illustrates contacts in low position with spacer in place for lower circuit UPPER CIRCUIT FIG 4 and 5 To convert attachment fitting for upper circuit raise BRASS CONTACT to high position as indicated by dotted line by pulling CONTACT as high as stop permits and slipping on BLACK SPACER as shown in Fig 4 and 5 FIG 3 MOVABLE BRASS CONTACT STATIONARY SILVERED CONTACT COMMON BLACK SPACER BLACK SPACER PLUG ASSEMBLY FIG 4 FIG 5 K
Download Pdf Manuals
Related Search