Home
        Lightolier IS:MIC100 User's Manual
         Contents
1.            instructions    POWER CORD  LUMINAIRE HOUSING  GROOVE IN END CAP  PULL  BACK OF  REAR OF LUMINAIRE END CAP  HOUSING  TAB  FIG 2  r 5 16  4 3 4 Ha 4 3 4  MOUNTING HOLES  FIG 3  POWER CORD       ot y  Sa  a Nee  20    MOUNTING SURFACE  o    SCREW  BY OTHERS     FIG 4    631 Airport Road  Fall River  MA 02720     508  679 8131    Fax  508  674 4710  We reserve the right to change details of design  materials and finish   www lightolier com    2008 Philips Group   A0508    Lightolier is a Philips group brand Erg ILI PS    LICH TOLIER    instruction Sheet Number IS  MIC1 00    Page 2 of 2 Installation of LED Undercabinet Lighting System    Read and understand these instructions before installing luminaire    This luminaire is intended for installation in accordance with the National Electrical Code and local regulations  To  assure full compliance with local codes and regulations  check with your local electrical inspector before  installation  To prevent electrical shock  turn off electricity at fuse box before proceeding    Retain these instructions for maintenance reference    Multiple Unit Installation Instructions   1  Remove END CAPS  by pressing down on TAB and pulling away from LUMINAIRE HOUSING  FIG 2      2  Insert CONNECTOR from JUMPER into RECEPTACLE on LED BOARD ASSEMBLY in LUMINAIRE HOUSING    3  Feed opposite end of JUMPER through JOINER and install JOINER to LUMINAIRE HOUSING snapping TAB into  place  FIG 1     4  Insert CONNECTOR into RECEPTACLE in adjo
2. LICH TOLIER    instruction Sheet Number IS  MIC1 00    Page 1 of 2 Installation of LED Undercabinet Lighting System    Read and understand these instructions before installing luminaire    This luminaire is intended for installation in accordance with the National Electrical Code and local regulations  To  assure full compliance with local codes and regulations  check with your local electrical inspector before  installation  To prevent electrical shock  turn off electricity at fuse box before proceeding    Retain these instructions for maintenance reference    Single Unit Installation Instructions   1  Choose which side to run POWER CORD from and remove END CAP  by pressing down on TAB and pulling away    from LUMINAIRE HOUSING  FIG 2   Insert CONNECTOR on POWER CORD into RECEPTICLE on LED BOARD  ASSEMBLY  not shown  in LUMINAIRE HOUSING    2  Run POWER CORD through GROOVE IN END CAP and out opening in back of END CAP  Snap END CAP back into  LUMINARE HOUSING  FIG 1     3  Align SCREWS  by others  with mounting holes and drive into MOUNTING SURFACE to firmly secure luminaire   FIG 3 amp 4   Use appropriate screws for mounting surface type    4  Run POWER CORD to remote power supply and wire POWER CORD into 24VDC side of LED RPS 50  not shown   power supply only  See instruction sheet for LED RPS 50 for detailed instructions    A maximum of  5  MIC100 series  luminaires can be used per LED RPS 50 power supply  see sheet  2  for multiple MIC100 series luminaire installation   
3. ining luminaire    5  Assemble the second LUMINAIRE HOUSING to the JOINER  FIG 1 amp 3     6   7         Repeat steps 1 4 for any additional LUMINAIRE HOUSINGS  You can have up to  5  MIC100 Series MAX     Choose which side to run POWER CORD from and insert CONNECTOR on POWER CORD into RECEPTICLE on  LED BOARD ASSEMBLY in LUMINAIRE HOUSING   8  Run POWER CORD through GROOVE IN END CAP and out opening in back of END CAP  Snap END CAP back into  LUMINARE HOUSING  FIG 1    9  Snap other END CAP into remaining open LUMINAIRE HOUSING end   10  Align SCREWS with mounting holes and drive into MOUNTING SURFACE to firmly secure luminaire s  FIG 3   Use  appropriate screws for mounting surface type   11  Run POWER CORD to remote power supply and wire POWER CORD into 24VDC side of LED RPS 50  not shown   power supply only  See instruction sheet for LED RPS 50 for detailed instructions              PULL            ROWER CORD LUMINAIRE HOUSING  REAR OF LUMINAIRE  HOUSING  TAB  CONNECTOR FIG 2  JUMPER  JOINER  END CAP  POWER CORD  9 1 2  MOUNTING FIG 1  GROOVE IN  END CAP  4 9 16  MOUNTING  HOLES  BACK OF  SCREW  BY OTHERS  END CAP    MOUNTING SURFACE    FIG 3    631 Airport Road  Fall River  MA 02720     508  679 8131    Fax  508  674 4710  We reserve the right to change details of design  materials and finish         f Bs www lightolier com    2008 Philips Group   A0508  Lightolier is a Philips group brand DH l LI PS    
    
Download Pdf Manuals
 
 
    
Related Search
    
Related Contents
modos  ET STEVIE WONDER = COMMENTAIRE SUR LE TRAITÉ  Barco MDCG-5121  BLDC Motor with Speed Closed Loop and DC-Bus  Emerson 381333122 E Switch User Manual  A7850 ナイフ(鎌型)  Anexo VIII - MPR/SGP 401-R00  Microsoft PowerPoint User Manual    Floor Scrubber & Polisher    Copyright © All rights reserved. 
   Failed to retrieve file