Home
        Lightolier V611 User's Manual
         Contents
1.  made by means of  MOUNTING BRACKET SCREWS  Fig  2  on inside of  MOUNTING FRAME        C  ADJUST SOCKET HOUSING    Engage SPRING to SLOTS for desired lamp wattage  position  see label on inside and outside of neck of  REFLECTOR HOUSING as shown on Fig  7      NOTE  To remove REFLECTOR HOUSING for  inspection and maintenance  push  RETAINING SPRINGS outward and detach  REFLECTOR HOUSING from MOUNTING  FRAME  See Fig  1     To insure neat installation  do not remove  CARDBOARD PAINT SHIELD  provided  in  MOUNTING FRAME  Fig  1   The SHIELD   will protect the inside of    REFLECTOR HOUSING from paint  plaster   and dust  Remove it only after construction RETAINING   is completed     ADJUSTABLE SOCKET  HOUSING        SLOT    REFLECTOR  HOUSING    FIG  7  D  CARE AND MAINTENANCE OF    ALZAK       REFLECTOR    If handling of reflectors with anodized or Alzak  finish is required  the use of clean white or plastic  film gloves recommended to avoid fingerprints     Anodized or Alzak surfaces can be cleaned by the  following methods     1  Wipe off with a soft  clean  dry  lint free cloth    2  Wipe off with a soft clean cloth dampened in  mild detergent solution  Rinse  then wipe dry with  lint free cloth or paper towel    3  Wipe off with a clean cloth dampened with a  solution of wetting agent and water  such as 2  oz  per gallon    Pluronic L62 LF    by Wyandotte  Products  or a liquid wax such as Glass Wax     Then wipe dry  Avoid gritty cleaning agents     
2. INSTRUCTION SHEET NO     INSTALLATION OF PRE WIRED CALCULITE FRAME4N KITS m 1 1  A LAMP WALL WASHER DOWNLIGHT a  INSTRUCTION SHEET FOR ITEMS  R0291 Page 1 of 2  V611  W612    READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE     This fixture is intended for installation in accordance with the National Electrical Code and local regulations  To assure full compliance  with local codes and regulations  check with your local electrical inspector before installation  To prevent electrical shock  turn off  electricity at fuse box before proceeding    Retain these instructions for maintenance reference     LAMPHOLDER SPRING    WALL WASHER  REFLECTOR HOUSING     ADJUSTABLE LAMPHOLDER HOUSING    DOWNLIGHT REFLECTOR ae ee  y i JUNCTION BOX    REFLECTOR HOUSING  PREASSEMBELED TO  MOUNTING FRAME             MOUNTING FRAME EA CARDBOARD PAINT SHIELD    WARNING    RISK OF FIRE  DO NOT INSTALL INSULATION WITHIN 3 INCHES OF FIXTURE SIDES OR  WIRING COMPARTMENT  NOR ABOVE FIXTURE IN SUCH A MANNER SO AS TO ENTRAP HEAT     NOTE  RELECTOR HOUSING must be Installed before closing in ceiling  Make sure finished ceiling is lined up with MOUNTING  FRAME  Fig  6      A  FRAME IN AND WIRE IN  FIG  1   1  Install FRAME IN SECTION using ADJUSTABLE MOUNTING BRACKET  see below    Wire to supply leads  White fixture lead to neutral supply lead  Black fixture lead to hot  120V   supply lead  Bare fixture wire to supply ground  Use wirenuts  local hardware items   Place all  electrical connecti
3. ons in the J BOX  Attach J BOX COVER onto J BOX     a  With MOUNTING BAR  order separately  b  With      CHANNEL  by others  c  With 1     CHANNEL  by others   18    Cat  No  1950  27    Cat  No  1951   using rectangular slots as shown  a    CHANNEL 1     CHANNEL     gt   BY OTHERS   MOUNTING   200   BY OTHERS   BAR i  E Da      Beat   E  i    ADJUSTABLE ADJUSTABLE SCREWS ADJUSTABLE     BRACKET  MOUNTING MOUNTING MOUNTING MOUNTING PANNA  f BRACKET FIGU3 FRAME BRACKET FIG  4 FRAME    For suspended ceilings T Bar ANCHOR CLIPS ACCESSORY For wood joist construction    No  1956  Order separately  may be used in conjunction with TELESCOPING MOUNTING BARS No   18    or 27    MOUNTING BARS for quick mounting  Fig  5a  or 7994  order separately  may be used to  simply wire MOUNTING BARS to ceiling members  Fig  5b   secure MOUNTING FRAME  Fig  5c      TELESCOPING  ANCHOR CLIPS MOUNTING BARS    MOUNTING  MOUNTING BAR BAR        E IG HTOI HEI SECAUCUS  NEW JERSEY  07096  om J m E fmm OR MONTREAL  QUEBEC  CANADA       as    TW  Page 2 of 2    INSTALLATION OF PRE WIRED CALCULITE FRAME IN KITS  A LAMP WALL WASHER DOWNLIGHT  Cont   d     B  ADJUST MOUNTING FRAME  For both plaster or other dry ceiling installation   MOUNTING FRAME must be set so that the  bottom edge is flush with the finished ceiling  as  shown on Fig  6     MOUNTING  FRAME    NOTE  1  To insure proper installation  the MOUNTING FRAME  must always be secure to structural ceiling members   2  Final vertical adjustment can be
    
Download Pdf Manuals
 
 
    
Related Search
    
Related Contents
    Investigation of the Effectiveness and Failure Rates of Whole  This protocol - Pelkmans Lab  AP ヒートガン 取扱説明書  Diamond Multimedia Radeon 9600 PRO User's Manual  Conceptronic C100S8A  National Instruments FP-AI-112 User's Manual  um en fl switch smcs - Onlinecomponents.com  Station météo pro Modèles : WMR80 / WMR80A - Station    Copyright © All rights reserved. 
   Failed to retrieve file