Lightolier C4P20MH User's Manual
Contents
1. shown and pushing up on FLANGE until it is fully installed into frame opening Re lamping 1 To re lamp one piece units simply unscrew the old lamp and replace with a new one There is no need to remove trim from ceiling 2 For two piece constructions remove CONE by pulling out of trim assembly re lamp and then replace CONE 3 See trim labeling for correct lamp info Follow lamp manufacturer s directions for proper care and handling of lamp LIGHTOLIER panonia tenor rem yo READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE INSTRUCTION SHEET NO This fixture is intended for installation in accordance with the National Electrical Code and local regulations To assure full compliance with local codes and regulations check with your local electrical inspector before f S 4 P20 M H installation To prevent electric shock turn off electricity at fuse box before proceeding m Retain these instructions for maintenance reference B0904 Page 2 of 2 INSTALLATION INSTRUCTIONS FOR 4 6 AND 7 RECESSED EVOLUTION H D DOWNLIGHT TRIMS REFLECTOR Es E HOUSING FRAME RING t _ LEAF SPRING LENS f RETENTION SPRING CONE CONE RETENTION SPRING Installation of 2 piece type construction Detail of Lens Removal and Replacement 1 Install REFLECTOR HOUSING into FRAME RING by aligning LEAF SPRINGS with slots in 1 On some trims it will be necessary to remove upper2. READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE INSTRUCTION SHEET NO This fixture is intended for installation in accordance with the National Electrical Code and local regulations To assure full compliance with local codes and regulations check with your local electrical inspector before f S 4 P20 M H installation To prevent electric shock turn off electricity at fuse box before proceeding m Retain these instructions for maintenance reference B0904 Page 1 of 2 INSTALLATION INSTRUCTIONS FOR 4 6 AND 7 RECESSED EVOLUTION H D DOWNLIGHT TRIMS ED17 Horizontal Lamp PAR type Open Downlights 1 Piece Construction 1 piece Construction PAR type Open Downlights 2 Piece Construction TRIM LAMPHOLDER RETENTION supplied with frame SPRING LAMPHOLDER SPRING supplied with frame REFLECTOR NECK Fig 1 Fig 2 Installing Lampholder onto Reflector Fig 1 1 Bring LAMPHOLDER through frame opening into workspace 2 Snap LAMPHOLDER SPRING into two slots on REFLECTOR NECK 3 Check to make sure that both sides of LAMPHOLDER SPRING are fully engaged into slots 4 Reflector trim is now ready for installation into ceiling Installing Reflector into Frame Fig 2 1 Install LAMPHOLDER onto REFLECTOR NECK 2 Feed assembled REFLECTOR into frame opening by aligning as
3. portion of FRAME RING the lens prior to re lamping 2 All LEAF SPRINGS must fully engage with 2 Toremove LENS push on one LENS slots for correct installation RETENTION SPRING to disengage it from the 3 Install CONE by pushing up into opening edge of the LENS CONE RETENTION SPRINGS will hold CONE 3 The LENS should easily come free from the in place remaining LENS RETENTION SPRINGS 4 To replace insert edge of LENS into all but one of the LENS RETENTION SPRINGS 5 Push LENS up to snap it into the remaining A LENS RETENTION SPRING Care and Maintenance of Alzak REFLECTOR TRIM finish If handling of REFLECTOR TRIM with anodized or Alzak finish is required the use of clean white or plastic film gloves is recommended to avoid fingerprints Anodized or Alzak surfaces can be cleaned by the following methods ED17 Horizontal Lamp Wipe off with a soft clean dry lint free cloth 2 piece Construction Wipe off with a soft clean cloth dampened in mild detergent solution Rinse then wipe dry with lint free cloth or paper towel Wipe off with a clean cloth dampened with a solution of wetting agent and water such as 2 oz Per gallon Pluronic L62 LF by Wyandotte Products Wipe dry Use a liquid wax such as Glass Wax Avoid gritty cleaning agents pP uS LIGHTOLIER panonia tere remy
Download Pdf Manuals
Related Search