Lightolier C12 User's Manual
Contents
1. PART OF THE LUMINAIRE LIGHTING FIXTURE INSTRUCTIONS FOR INSTALLING C12E28FL AND C12E28PL SERIES LENSLITE DOWNLIGHT REFLECTOR TRIM PS tom a INSTALLING SOCKET CUP TO REFLECTOR A mal SCREWS 1 Attach SOCKET CUP to REFLECTOR ASSEMBLY by aligning 3 7 SCREWS with key slots in REFLECTOR NECK then tighten screws Sejma REFLECTOR Fig 1 i P NECK CTO 2 Raise REFLECTOR ASSEMBLY SOCKET CUP into MOUNTING RING ian of Frame In Kit or Cylinder align REFLECTOR SPRINGS with upper slots in MOUNTING RING until springs snap in place Fig 1 KS SLOTS 3 Before lamping make sure power is disconnected to fixture i i Install lamp into lampholder Fig 1 7 i ETOR i SPRINGS 4 After REFLECTOR ASSEMBLY is installed attach LENS BAFFLE by MOUNTING RING squeezing TORSIONTITE SPRINGS together and insert through SLOTS in REFLECTOR then push up Fig 1 CONE RETAINING SPRINGS 5 For tamper proof installation remove SET SCREW from outside of LENS BAFFLE and re install it with the allen wrench socket head facing eee inside of LENS BAFFLE Turn SET SCREW until socket head is about 1 8 inside baffle Do not over turn Fig 2 If SET SCREW was SLOTS properly installed LENS BAFFLE should not pull down j SET y je ait TO RELAMP SCREW Tr Ne LENS BAFFLE Disconnect power to fixture Back out SET SCREW if used for tamper f y proof installation Lift lens up and grip top edg2. READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE INSTRUCTION SHEET NO This fixture is intended for installation in accordance with the National Electrical Code and local regulations To assure full compliance with local codes and regulations check with your local electrical inspector before IS s C 1 2 installation To prevent electric shock turn off electricity at fuse box before proceeding 7 Retain these instructions for maintenance reference A1204 Page 1 of 2 INSTALLATION PROCEDURE FOR 12 DIA H I D C12 SERIES REFLECTOR TRIM TO C12 SERIES FRAME IN KIT AND C12CS C12CW CYLINDER ORDER SEPARATELY IF A NON IC TYPE RECESSED FRAME IN KIT IS USED DO NOT INSTALL INSULATION ABOVE NOR WITHIN 3 INCHES 76mm OF ANY PART OF THE LUMINAIRE LIGHTING FIXTURE INSTRUCTIONS FOR INSTALLING C12E28V SERIES DOWNLIGHT REFLECTOR TRIM 1 Attach SOCKET CUP to REFLECTOR ASSEMBLY by aligning 3 SCREWS H SOCKET CUP with key slots in REFLECTOR NECK then tighten screws Fig 1 m SCREWS 2 Position REFLECTOR ASSEMBLY into MOUNTING RING of Frame In z Kit or Cylinder align 4 FLATS in REFLECTOR ASSEMBLY with 4 a O CONE RETAINING SPRINGS and align REFLECTOR SPRINGS with a a NECK UPPER SLOTS in MOUNTING RING Fig 1 amp 2 Then raise REFLECTOR Z _ PE ASSEMBLY to snap in place FIG 1 J ASSEMBLY 3 Before lamping make sure power is disconnected to fixture Install lamp into lamph
3. e of baffle then pull down Me TO INSPECT AND REPLACE BALLAST FIG 1 Disconnect power to fixture Back out SET SCREW if used for tamper proof installation Lift lens up and grip top edge of baffle then pull down and rE detaching TORSIONTITE SPRINGS Detach REFLECTOR ASSEMBLY Uut by disengage REFLECTOR SPRINGS move it to side of fixture in the k al plenum or in cylinder remove from cylinder See 1S C4 C12 Frame In Kit and IS C12CS Cylinder for ballast replacement After service reverse Installation steps Care and Maintenance of REFLECTOR TRIM finish If handling of REFLECTOR TRIM with anodized finish is required the use of clean white or plastic film gloves is recommended to avoid fingerprints Anodized surfaces can be cleaned by the following methods 1 Wipe off with a soft clean dry lint free cloth 2 Wipe off with a soft clean cloth dampened in mild detergent 3 solution Rinse then wipe dry with lint free cloth or paper towel 4 Wipe off with a clean cloth dampened with a solution of wetting agent f A and water such as 2 oz Per gallon Pluronic L62 LF by Wyandotte B E Products Wipe dry 5 Use a liquid wax such as Glass Wax Avoid gritty cleaning agents FIG 2 LIGHTrOLIER SET LICSIITOLIER a Genlyte company 631 Airport Road Fall River MA 02720
4. ith anodized finish is required the use A of clean white or plastic film gloves is recommended to avoid fingerprints ty y tp Anodized surfaces can be cleaned by the following methods l 1 Wipe off with a soft clean dry lint free cloth 2 Wipe off with a soft clean cloth dampened in mild detergent solution CONE 3 Rinse then wipe dry with lint free cloth or paper towel 4 Wipe off with a clean cloth dampened with a solution of wetting agent and water such as 2 oz Per gallon Pluronic L62 LF by Wyandotte Products Wipe dry 5 Use a liquid wax such as Glass Wax Avoid gritty cleaning agents FIG 4 l I C gt H TOI HEIR ost Airport Road Fal River MA 02720 READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE INSTRUCTION SHEET NO This fixture is intended for installation in accordance with the National Electrical Code and local regulations To assure full compliance with local codes and regulations check with your local electrical inspector before IS m C 1 2 installation To prevent electric shock turn off electricity at fuse box before proceeding E Retain these instructions for maintenance reference A1204 Page 2 of 2 INSTALLATION PROCEDURE FOR 12 DIA H I D C12 SERIES REFLECTOR TRIM TO C12 SERIES FRAME IN KIT AND C12CS C12CW CYLINDER ORDER SEPARATELY IF A NON IC TYPE RECESSED FRAME IN KIT IS USED DO NOT INSTALL INSULATION ABOVE NOR WITHIN 3 INCHES 76mm OF ANY
5. older _ 4 7 PUSH jur A 4 Install COVER GLASS required for enclosed lamp rated BEAD CHAIN fixture line up the edge of COVER GLASS with one spring COUPLER GLASS RETAINING opposite notch on REFLECTOR ASSEMBLY and gently Pe PERAR push glass outward then lift glass upward into position Jo 2 COVER GLASS Rotate COVER GLASS so that NOTCH in COVER GLASS SLOTS i is away from NOTCH in REFLECTOR ASSEMBLY Fig 1 amp 3 _ ooo PA 4 MOUNTING RING 5 Hook SAFETY BEAD CHAIN onto BEAD CHAIN COUPLER Z Position CONE so that bead chain is about horizontal then push ae i aai aa CONE up into MOUNTING RING then turn CONE clockwise slightly for tight fit onto ceiling CONE RETAINING SPRINGS will FIG 1 hold cone in place Fig 1 amp 4 GLASS RETAINING SPRINGS TO RELAMP COVER GLASS Disconnect power to fixture then reverse installation ia instructions above Via a a ae REFLECTOR f SD ASSEMBLY TO INSPECT AND REPLACE BALLAST CONE RETAINING AN N Disconnect power to fixture Remove Cone Detach REFLECTOR 7 ES oo ASSEMBLY by disengage REFLECTOR SPRINGS move it to side i eras of fixture in the plenum or in cylinder remove from cylinder See IS C4 C12 Frame In Kit and 1S C12CS Cylinder for ballast o FIG 2 replacement After service reverse Installation steps 8 SAFETY BEAD CHAIN Care and Maintenance of REFLECTOR TRIM finish If handling of REFLECTOR TRIM w
Download Pdf Manuals
Related Search