Life Fitness tr 8500 User's Manual
Contents
1. TREADMILL INSTALLATION INSTRUCTIONS Congratulations welcome to the world of ALI 2 LINESS and the Life Fitness 8500 treadmill The following Parts Identification Listing and the step by step installation procedures have been assembled to make the set up of your aerobic trainer as quick and easy as possible Please take special note of the following important points prior to choosing a location and beginning assembly of the treadmill SAFETY FIRST DO NOT position the rear of the treadmill within 3 feet 1 meter of the nearest obstruction Life Fitness recommends a clearance of 6 feet 2 meters at the rear of the treadmill The sides of the treadmill should maintain a minimum clearance of 8 inches 21 cm from the nearest treadmill or other obstruction DO NOT locate the treadmill any closer than 30 inches 76 cm to a television set DO NOT locate the treadmill outdoors near swimming pools or in areas of high humidity DO verify the contents of the delivery carton against the accompanying parts listing prior to setting the cartons and shipping material aside If any parts are missing contact Life Fitness Customer Support Services at the number listed on the back page of this installation instruction booklet Save the shipping cartons in case of return DO read the entire Operation Manual prior to attempting to operate this machine as this is essential for proper use The Manual explains how to proper2. 4 0017 00101 1148 HANDLEBAR ASSEMBLY Qty 1 AK36 00019 0002 HANDLEBAR WASHERS Qty 6 0017 00104 0005 LEFT HANDRAIL Qty 1 AK36 00056 0004 HANDRAIL BOLTS Qty 4 0017 00101 1235 HANDRAIL SCREWS Qty 4 0017 00101 1210 HANDRAIL SIDE CAP RIGHT Qty 1 0K36 1089 0005 17 ENDCAP Qty 1 0K36 01085 0004 TINNERMAN CLIP Qty 2 0017 00103 0185 CENTER SUPPORT AK36 00072 0000 CENTER SUPPORT SCREWS 0017 00101 1007 HANDLEBAR SCREW 0017 00101 1380 i STOP KEY AK36 00027 0002 RIGHT HANDRAIL AK36 00056 0003 HANDRAIL WASHERS 0017 00104 0044 REMOVEABLE RIVET 0017 00042 0870 HANDRAIL SIDE CAP LEFT 0K36 1089 0006 ENDCAP SCREWS 0017 00101 1159 WAX KIT GK45 00002 0001 Qty 1 Qty 4 Qty 6 Qty 1 Qty 1 Qty 4 Qty 4 Qty 1 Qty 6 Qty 1 Hardware included in the Parts Bag are shown here in Actual Size 5 mi KO TM em 6 Step 1 Untie and uncoil the WIRE HARNESS attached to the front right side of the treadmill Pull gently on the HARNESS to remove any slack Step 2 Place the RIGHT HANDRAIL next to the treadmill and feed the WIRE HARNESS CONNECTOR into the slot located at the bottom of the RIGHT HANDRAIL 10 until it exits through the top opening Step 3 14 Position the RIGHT HANDRAIL 10 in place on the treadmill FRAME and align the mounting holes in the HANDRAIL with those in the FRAME Insert the two H
3. the HANDRAIL CENTER SUPPORT into position between the two HANDRAILS and secure it with the four CENTER SUPPORT SCREWS 4 Step 7 Secure the bottom sides of the HANDRAILS to the angled FRAME BRACKETS using two SCREWS 13 for each HANDRAIL THE SCREWS 13 MUST BE FIRMLY TIGHTENED BEFORE TIGHTENING THE HANDRAIL BOLTS 11 TO INSURE PROPER STABILITY OF THE UPPER TREADMILL Step 8 Tighten the HANDRAIL BOLTS 11 securing the base of each of the VERTICAL HANDRAILS to the FRAME of the treadmill Position the right 15 and left 16 HANDRAIL SIDE CAPS into place on the corresponding HANDRAILS and secure each with two REMOVEABLE RIVETS 14 Step 9 Insert the two TINNERMAN CLIPS 19 into the slots as shown below Check that the holes in the extrusion align with the holes in the TINNERMAN CLIPS Set the ENDCAP 17 into position and secure in place with the six ENDCAP SCREWS 18 Step 10 Open the WAX KIT 20 and install the WAX according to the directions provided on the Instruction Sheet enclosed within the WAX KIT WARNING DO NOT OPERATE THE LIFE FITNESS 8500 TREADMILL PRIOR TO INSTALLING THE WAX ACCORDING TO THE INSTRUCTIONS ENCLOSED WITHIN THE WAX KIT FAILURE TO INSTALL THE WAX PRIOR TO USE MAY CAUSE DAMAGE TO THE UNIT AND VOID YOUR WARRANTY MISE EN GARDE VOUS DEVEZ METTRE DE LA CIRE CONFORM MENT AUX INSTRUCTIONS COMPRISES AVEC LE N CESSAIRE DE CIRE AVANT DE FAIRE FONCTIONNER L EXERCISEUR DE MA
4. ANDRAIL BOLTS 11 and WASHERS 12 through the HANDRAIL and into the FRAME to secure it Tighten these BOLTS until snug then loosen both BOLTS two complete revolutions counter clockwise Repeat this step for the LEFT HANDRAIL 9 NOTE The HANDRAIL BOLTS 11 must be loose at this time to facilitate the assembly of the HANDLEBAR ASSEMBLY 5 and the CENTER SUPPORT 2 CAUTION BE CAREFUL NOT TO PINCH WIRES BETWEEN THE RIGHT HANDRAIL AND THE UNIT FRAME REMARQUE FAIRE ATTENTION DE NE PAS PINCER LES FILS LORSQU ON ABAISSE LA MAIN COURANTE Step 4 Snap together the male and female 10 PIN CONNECTORS protruding from the top of the RIGHT HANDRAIL 10 and the underside of the HANDLEBAR ASSEMBLY 5 Once connected feed the excess cable carefully back into the top of the HANDRAIL Rest the HANDLEBAR in position on the VERTICAL HANDRAILS and install the six SCREWS 6 and WASHERS 7 to secure the HANDLEBAR ASSEMBLY to the two VERTICAL HANDRAILS Step 5 Snap the 10 PIN CONNECTOR protruding from the top of the HANDLEBAR ASSEMBLY 5 into the corresponding CONNECTOR in the back of the 13 DISPLAY CONSOLE 1 Snap the 6 PIN X CONNECTOR of the extended memory board wire 4 2 harness located in the display console bracket into the corresponding CONNECTOR in the back of the DISPLAY CONSOLE Install the four SCREWS 3 in a criss cross pattern to secure the DISPLAY CONSOLE to the HANDLEBAR ASSEMBLY Step 6 Place
5. E WHEN ADJUSTING THE STRIDING BELT YOU MUST ADJUST BOTH SIDES EQUALLY E G ADJUST THE LEFT SIDE 1 4 TURN CLOCKWISE AND THE RIGHT SIDE 1 4 TURN COUNTER CLOCKWISE OPERATION CHECKLIST Make sure the HANDLEBAR and HANDRAIL BOLTS are tight Make sure the STRIDING BELT is properly centered or tracked Check the operation of the STOP KEY Check to insure that the POWER CORD is not located beneath or alongside the machine Read the entire Operation Manual before attempting to operate the treadmill Check to insure the WAX KIT was installed prior to operation ENGLISH METRIC DEFAULT SETTING TOGGLE The default setting of the Life Fitness 8500 Treadmill Display Console is set to English units of measurements at the factory If your Display Console will require units of measurements to be in Metric it may be necessary to change the setting from English to Metric To do so you will need to enter into the Diagnostic Programs and proceed to Diagnostic State 4 To do so follow the instructions as listed below Start with the Life Fitness model 8500 treadmill turned OFF at the I O switch located adjacent to the power cord Press and hold the SPEED DOWN KEY V while switching the I O switch setting to ON All LED s on the Display Console will light Press ENTER four times to scroll through the Diagnostic Modes and enter the Software Version Language default settings The display console will now show a series of numbers and l
6. RCHE LIFE FITNESS 8500 LE FAIT DE NE PAS METTRE DE CIRE AVANT D UTILISER L APPAREIL POURRAIT ENDOMMAGER L EXERCISEUR ET ANNULER LA GARANTIE Step 11 The treadmill STRIDING BELT is properly centered at the factory however the Life Fitness 8500 treadmill must be leveled in the location it is to be used After placing the treadmill in its intended location for use check the stability of the unit If the unit is not stable turn the LEVELING LEGS clockwise or counterclockwise until the rocking motion is diminished IT IS EXTREMELY IMPORTANT THAT THE TREADMILL BE CORRECTLY LEVELED FOR PROPER OPERATION AN UNSTABLE UNIT MAY CAUSE STRIDING BELT MISALIGNMENT IL EST EXTREMEMENT IMPORTANT QUE L EXERCISEUR SOIT DE NIVEAU POUR UN FONCTIONNEMENT AD QUAT UN APPAREIL INSTABLE RISQUE DE D SALIGNER LA COURROIE DE MARCHE Step 12 Insert the STOP KEY 8 into the slot on the front of the HANDLEBAR ASSEMBLY 5 Plug the machine POWER CORD into a properly grounded ELECTRICAL outlet Insert the SAFETY KEY into the POWER SWITCH near the POWER CORD and toggle it to the ON or I position The Safety key can be removed to prevent unauthorized use SWISH SA TY KEY Step 13 Begin a program but DO NOT begin running It is important to insure that the STRIDING BELT remains centered during operation If the BELT drifts to the right see Figure A If the BELT drifts to the left see Figure B FIGURE A FIGURE B NOT
7. etters TT 140 Jose For example the Display will read 2 9EE1 _2 9EE1 FETA 2 9 Software Version HEE 3 E English Measurement miles M would designate Metric kilometers ID E Engli glish Language 806 1 120V 299 x ATTRAE d Press ENTER a fifth time and UNITS appears in the Display readout Pressing the SPEED UP A KEY enables you to change the unit of measure from ENGLISH ENGLISH to ENGLISH METRIC Pressing the SPEED DOWN KEY V enables you to change the unit from ENGLISH METRIC to ENGLISH ENGLISH Press the CLEAR key 1 time to verify the default after you have chosen a setting Continue to press the CLEAR PAUSE key to scroll backwards through the Diagnostics and return to normal operation Before attempting to operate your Life Fitness 8500 treadmill it is imperative that you familiarize yourself with the contents of the Operation Manual If your treadmill does not respond as described in the OPERATION MANUAL contact Prior to your call please be sure you have located and noted the of your Life Fitness 5500HR treadmill This information is contained on a label located in front of the Left Handrail on the frame of the SERIAL NUMBER Life Fitness Customer Support Services at 800 351 3737 or 847 451 0036 MODEL and SERIAL NUMBER treadmill Copyright 1996 Life Fitness All rights reserved Life Fitness is a registered trademark of Life Fitnes
8. ly use the treadmill and helps you to design an aerobic workout tailored to your personal fitness needs or requirements Ne Jamais Placer l arri re de l exerciseur moins de 3 pieds 1 m tre de l obstacle le plus pr s Life Fitness recommande un espace libre de 6 pieds 2 m tres l arri re de l exerciseur Le Life Fitness 8500 doit tre install 8 pouces 20 cm d un autre exerciseur et 30 pouces 76 cm d une t l vision Ne pas utiliser l ext rieur proximit des piscines ou dans des lieux ou l humidit est lev e Avant de commencer l assemblage et de jeter les mat riaux d emballage comparer le contenu avec la liste des pi ces comprises S il manque des pi ces appeler le service de soutien Le Services Life Fitness Customer Support E U en composant le 1 800 351 3737 ou le 1 847 451 0036 ou le Life Fitness Europe Munich Germany en composant le 49 89 310 6078 Sauvegarder les bo tes d emballage en cas de renvoi Avant de faire fonctionner l appareil Life Fitness 8500 il est n cessaire de lire tout le guide de fonctionnement Celui ci explique comment utiliser correctement le l exerciseur et facilite l laboration d un programme d entra nement a robique adapt vos besoins de conditionnement personnels TOOLS REQUIRED FOR ASSEMBLY Phillips screwdriver Hex key wrench set PARTS DESCRIPTION DISPLAY CONSOLE ASS Y Qty 1 AK45 00036 0001 DISPLAY CONSOLE SCREWS Qty
9. s M051 00K45 B019 5 96
Download Pdf Manuals
Related Search