Life Fitness Smith Machine User's Manual
Contents
1. 5 kgs Size 49 D 124 5cm x 86 6 W 220cm x 92 8 H 235 7cm Live Area 10 L 3 0m x 10 W 3 0m Max Training Weight 650 Ibs 309 kgs Max Plate Capacity 7 45 lb plates per side 20 Ib Lift Bar 650 Ibs 6 25 kg plates per side 9 kg Lift Bar 309 kgs Signature Smith Machine Assembly Instructions Item Qty Description Part Number 4 1 1 Left Side Frame 82942xx Ref 2 1 Right Side Frame 82943xx Ref 3 1 Back Brace 82949xx Ref 4 10 M10 X 130mm Bolt 3236220 5 5 22 3 8 Washer 3236601 6 10 1 4 Spacer 82 OD 7634701 7 10 10 Socket Head Nut 7335401 8 6 10 X 25mm Bolt 3236202 9 10 1 Hole Plug 3237403 10 8 10 Hex Nylock Nut 3236801 11 1 Front Brace 82947xx 8 9 1 0 2 4 Linear Bearing 8271101 3 1 Left Carriage 83374xx Ref HHT Ht 4 4 Snap Ring 3202602 5 1 Right Carriage 83376xx Ref 6 1 Lift Bar 82963xx Ref 7 2 Bar Stop 82956xx Ref 8 2 M10 Jam Nut 3236901 9 2 Cable 8328401 18 21 22 20 2 Rod End 3237901 21 2 M10 X 40mm Bolt 3236205 N O 22 2 Rod End Spacer 5 OD 7489402 Tools Required e 7mm Allen Wrench 2X 17mm Deep Socket e Snap Ring Plier 5mm Allen Wrench 17mm Open End Wrench e Tape Measure e Ratchet with 17mm Socket 24mm Open End Wrench e Ratchet Extension LiF Signature Smith Machine Assembly Instructions BE SURE TO SELECT A LEVEL LOCATION FOR ASSEMBLY THE SIGNATURE SMITH MACHINE MUST REST LEVEL AND IN COMPLETE CONTACT WITH THE2. FLOOR With the help of another person erect the LEFT and RIGHT SIDE FRAMES 1 amp 2 Position the SIDE FRAMES approximately 50 inches between the inside flat sections of the LIFT BAR RACKS A for ease of assembly From the side loosely assemble BACK BRACE 3 to the LEFT SIDE FRAME 1 using three M10 x 130mm BOLTS 4 three 3 8 SAE WASH ERS 5 three 1 4 SPACERS 6 and three M10 x SOCKET HEAD NUTS 7 From the back install three M10 X 25mm BOLTS 8 six 3 8 SAE WASHERS 5 and three M10 HEX NYLOCK NUTS 10 Finger tighten the BOLTS and NUTS only Repeat the procedure to assemble the BACK BRACE 3 to the RIGHT SIDE FRAME 2 Loosely assemble the FRONT BRACE 11 to the LEFT and RIGHT SIDE FRAMES 1 amp 2 using four M10 X 130mm BOLTS 4 four 3 8 SAE WASHERS 5 four 1 4 SPACERS 6 and four M10 SOCKET HEAD NUTS 7 4 5 Insert two LINEAR BEARINGS 12 into the ends of the RIGHT CARRIAGE 15 secure the LINEAR BEARINGS with one SNAP RING 14 at each bearing NOTE Leave the cardboard sleeve in the bottom LINEAR BEARING remove the cardboard sleeve from top bearing Repeat the procedure on the LEFT CARRIAGE 13 Assemble the CARRIAGES 13 amp 15 to the LIFT BAR 16 and as shown Make sure the LIFT BAR is inserted completely through both roller bear ings located within the CARRIAGE TUBES B Signature Smith Machine Assembly Instructions 6 Loosen
3. the four set screws on the pre assembled 1 25 SHAFT COLLARS C located at the top of the SIDE FRAMES 7 With the help of another person and the LIFT BAR ASSEMBLY D oriented as shown position it near the bottom of the GUIDE RODS E Lift both GUIDE RODS up through the top of the SIDE FRAMES Hang the LIFT BAR ASSEMBLY on the third LIFT BAR RACK A hook 8 Making sure the SHAFT COLLAR and BUMPER remain above the CARRIAGE insert one GUIDE ROD into CARRIAGE of the LIFT BAR ASSEMBLY 9 Slide one BAR STOP 17 on the GUIDE ROD E and slide the GUIDE ROD back inside SIDE FRAME NOTE Make sure the warning label faces inward when assembling the BAR STOP 17 on the GUIDE ROD E 10 Repeat steps 9 amp 10 for to assemble remaining GUIDE ROD to the LIFT BAR ASSEMBLY 11 Adjust the machine so the measured distance between inside faces of the LIFT BAR RACKS A both top and bottom is 48 13 16 to 49 5 16 inches 123 98 to 125 25 cm Tighten all BOLTS and NUTS securely 12 Thread the one JAM NUT 18 fully onto each of the CABLE 19 ends Thread one ROD END 20 onto each of the CABLE ends approximately 12 DO NOT TIGHTEN JAM NUT 13 Attach one ROD END 20 to each of the CARRIAGES using one M10 X 40mm BOLT 21 one ROD END SPACER 22 and one M10 HEX NYLOCK NUT 10 per side Tighten the NUTS securely 14 Cycle the LIFT BAR up and down There must not be any banging of the COUNTER WEIGHTS located inside the large front tubes at e
4. Any failures or damage caused by unauthorized service misuse accident negligence improper assembly or installation debris resulting from construc tion activities in the vicinity of the Product any alterations or modifications made to the Product without written authorization by Life Fitness or by failure on your part to use operate and maintain the Product as set out in your Operation Manual All terms of this warranty are void if this product is moved beyond the continental borders of North America excluding Hawaii and are then subject to the terms provided by that country s authorized Life Fitness Representative TRANSPORTATION amp INSURANCE FOR SERVICE If the Product or any covered part must be returned to a service facility for repairs Life Fitness will pay all transportation and insurance charges for the first year You are responsible for transportation and insurance charges for year 2 and beyond HOW TO GET PARTS amp SERVICE Simply call Customer Support Services at 800 351 3737 or 847 451 0036 Monday through Friday from 8 00 a m to 6 00 p m Central Standard Time and tell them your name address and the serial number of your Product They will tell you how to get a replacement part or if necessary arrange for service where your Product is located or advise you on how and where to ship the Product for service Before shipping 1 Obtain a Return Authorization Number RA from Customer Support Services 2 Securely pack
5. Signature Smith Machine Owners Manual Signature Smith Machine Safety amp Warranty Purchasers of LIFE FITNESS products should read the Owner s Manual and all of the warning labels on the products before using them Because these products may be used in commercial settings it is the purchaser s responsibility to instruct all individuals whether users trainers or observers on the proper usage of the equipment Contact Life Fitness if you do not know how to use this equipment LIFE FITNESS recommends that all commercial fitness equipment be used in a supervised area Life Fitness also recommends that the equipment be located in an access controlled area The extent of control is at the discretion of the owner SECURING EQUIPMENT All strength equipment must be secured to the floor to a solid level surface to stabilize and eliminate rocking or tipping over This must be performed by a licensed contractor LIFE FITNESS recommends that all users be informed of the following prior to using LIFE FITNESS equipment PROPER USAGE A It is imperative that LIFE FITNESS equipment be used properly to avoid injury Do not use any equipment for purposes other than those speci fied by the manufacturer Keep body parts hands feet hair etc and clothing away from moving parts to avoid injury Injuries may result if you exercise improperly or excessively It is recommended that all individuals consult a physician prior to commencing an exer
6. and their connections before using machine DO NOT attempt to fix Seek assistance Use only the incremental weights supplied by the manufacturer DO NOT use dumbbells or other means to add resistance to the machine Children must not be allowed near this machine Supervise teenagers Manufacturer recommends that all equipment be secured to the floor to stabilize and eliminate rocking or tipping over Use a licensed contractor DO NOT REMOVE THIS LABEL REPLACE IF DAMAGED Signature Smith Machine Safety amp Warranty LIMITED WARRANTY WHAT IS COVERED This Life Fitness commercial exercise equipment Signature Benches and Racks is warranted to be free of all defects in material and workmanship to the original purchaser for the specific items and duration listed 10 years on structural frame 1 year on bearings 1 year on grips 1 year on cables and belts if so equipped 1 year for rust or corrosion of structural frame Scratches or scrapes where the subsurface of the unit has been exposed must have been properly repaired by the customer e 90 days on upholstery and any items not specified including labor Life Fitness will ship to you at our expense any repair parts covered by the warranty as stated If the Product is deemed not repairable by Life Fitness authorized personnel we reserve the right to replace any part or the entire Product at our option within the stated warranty period WHAT IS NOT COVERED
7. cise program If at any time during exercise you feel faint dizzy or experience pain stop and consult your physician When adjusting any seat knee hold down pad or range of motion limiter make certain that the adjusting pin is fully engaged in the hole to avoid injury CHECK FOR DAMAGED PARTS AN DO NOT use or permit the use of any equipment that is damaged or has worn or broken parts For all LIFE FITNESS equipment use only replacement parts supplied by LIFE FITNESS MAINTAIN LABELS AND NAMEPLATES Do not remove labels for any reason Labels contain important information If unreadable or missing contact LIFE FITNESS for a replacement MAINTAIN ALL EQUIPMENT Preventative maintenance is the key to smooth operating equipment Equipment should be inspected at regular intervals See the Maintenance section of this manual for recommended maintenance intervals Ensure that any person s making adjustments or performing maintenance or repair of any kind is qualified to do so LIFE FITNESS will provide service and maintenance training at one of its facilities upon request or in the field if proper arrangements are made SPECIFIC OPERATING WARNINGS N gt 2 UNDERSTANDING THE FULL EXTENT OF EACH AND EVERY WARNING IS IMPORTANT IF ANY WARNING IS UNCLEAR ASK LIFE FITNESS PERSONNEL FOR CLARIFICATION Keep children away from strength equipment Use only olympic style weight plates 2 0 Bore for training weight Only add weight up t
8. ights and you may have other rights which vary from state to state OUR PLEDGE TO YOU Our Products are designed and manufactured to the highest standards We want you completely satisfied with our Products and will do everything possible under the terms of this warranty to keep you secure in knowing you have bought the best Lief ilies Signature Smith Machine Safety amp Warranty 1 Frame Construction Frame is constructed of mechanical quality steel purchased in mill run quantities Frame is primarily 2 1 2 x 4 1 2 oval shaped tubing and 5 1 4 x 3 3 4 D shaped tubing with 11 gauge wall thickness 2 Frame Finish The frames are coated with an electrostatic epoxy powder coat finish 3 Bolts Most hardware is metric and has a corrosion resistant finish Grade 5 or greater in strength 4 Hand Grips Hand grips are an extruded 60 durometer thermorubber compound that is non absorbing wear and tear resistant and exhibits good dry and wet frictional characteristics The grips are retained with aluminum collars which eliminates the tendency of the grips to slide off the handle 5 Equipment Anchoring All machines have holes in the feet these allow easy anchoring to the floor Life Fitness recommends that all machines be anchored to the floor to minimize the possibility of tipping 6 Liability Insurance Certificate of insurance available upon request SIGNATURE SMITH MACHINE Product SSM Machine Weight 581lbs 263
9. ither the top or the bottom of the cycle The Product MUST pass BOTH of the following criteria A With the LIFT BAR at its topmost position CARRIAGES against BUMP STOPS both CABLES need to be in tension If the cable is not tensioned screw the loose CABLE into ROD END until the cable is taut Re cycle the lift bar and recheck the cable tension When cable is properly tensioned proceed to criteria B B Position the LIFT BAR at its bottommost position LIFT BAR and BAR STOPS not engaging LIFT BAR RACKS Be sure both BAR STOPS are resting on the SIDE FRAMES and both CARRIAGES are resting on the BAR STOPS Ensure that the cable is not too tight by slight pulling down on the CABLE while holding the LIFT BAR firmly at its bottommost position The cable should move slightly approximately 1 4 to V2 inch If the cable is too tight unscrew the tight CABLE out of the ROD END making sure a minimum of three threads are engaged C If both above criteria cannot be satisfied see Counterweight Cable Adjustment When all of the above criteria have been met tighten the JAM NUT 18 and continue to complete the installation 15 Install 1 HOLE PLUGS 9 into all open bolt holes 16 Cycle the machine to ensure smooth LIFT BAR operation up and down Counterweight Cable Adjustment If the CABLE is still too tight after maximum ROD END adjustment the CABLE END on the COUNTER WEIGHT side will need t
10. o be adjusted Adjusting the CABLE END on COUNTERWEIGHT should be done in the following manner 1 Remove one M10 X 40mm BOLT 21 one ROD END SPACER 22 and one M10 HEX NYLOCK NUT 10 from each of the CARRIAGES 13 amp 15 Holding the ROD END 20 firmly slowly lower the COUNTERWEIGHT a until it reached bottom 2 Remove the two M10 X 20mm BOLTS b from the TOP D TUBE CAP c and remove the cap 3 Remove one M10 X 50mm BOLT d two FLAT WASHERS e and one NUT f from the PULLEY g and remove the PULLEY 4 Remove the two M10 X 20mm BOLTS h and FLAT WASHERS j from the GUIDE ROD BRACKET k and remove the BRACKET through the top of the machine 5 Pull the CABLE until the top of the COUNTERWEIGHT a is just above the top of the D TUBE Prop the COUNTERWEIGHT to prevent it from sliding into the D TUBE CAUTION DO NOT PULL COUNTERWEIGHT COMPETELY OFF OF GUIDE RODS m 6 Loosen the JAM NUT n on top of the COUNTERWEIGHT a and thread the CABLE END o in if CABLE is too long or out if CABLE is too short Retighten the JAM NUT 7 Guide the COUNTERWEIGHT a down the GUIDE RODS m until it reaches the bottom 8 Reassemble all removed components in reverse order of removal Tighten all bolts and nuts securely 9 Return to Step 13 and continue to confirm criteria is met Signature Smith Machine Maintenance ONCE A WEEK e Visually inspect all hardware including jam nuts for loosening tampering or wea
11. o the load limits of the unit and that can be fully placed on the weight horn Contact a Life Fitness representative with any questions regarding proper weights and loading A WARNING Bar will fall if hook is not fully engaged into slot Start resistance 20 Ibs 9 kg Max load capacity 7 45 Ib plates per side 6 25 kg plates per side 8349501 Do not use without setting adjustable stop Proper Adjustment Before using machine adjust stops just below the desired range of motion for the exercise to be performed 8349301 AWARNING SERIOUS INJURY CAN OCCUR ON THIS EQUIPMENT YOU MUST FOLLOW THESE PRECAUTIONS TO AVOID INJURY Before using read all the warnings and obtain instruction on the use of this machine Use only for intended exercise DO NOT modify the machine Obtain a medical exam before beginning any exercise program Keep body hair and clothing free of all moving objects Inspect the machines before use DO NOT use if it appears damaged DO NOT attempt to fix a broken or jammed machine Notify staff immediately Be certain that weight pin is completely inserted Use only the pin provided by the manufacturer If unsure seek assistance Never pin the weights or prop plate into an elevated position DO NOT use the machine if found in this condition DO NOT attempt to fix Seek assistance Inspect cables
12. r e Check condition of hand grips ONCE A MONTH e Inspect hardware and tighten any bolts or nuts that may have loosened during use e Clean Guide Rods with Break Free on a cotton cloth wipe off old residue Clean visible sides of linear bearings on carriages e Check Jam Nuts on Rod Ends for tightness ACTION DAILY MONTHLY BI ANNUALLY AS NEEDED CLEAN Hand Grips X Guide Rods X INSPECT Hardware X Frame X Hand Grips X Jam Nuts X CLEAN e Wax Frames with standard non abrasive wax finish e Hand grips with mild soap and water Guide Rods with cotton cloth and Break Free SK50 P0005 0000 INSPECT e Hardware should be checked for looseness Tighten as required using metric tools e Frames should be inspected for wear or damage e Hand grips should be checked for wear or damage e All paint chips should be filled immediately with touch up paint NOTE Use polishing compound such as car wax to clean and remove shoe scuffs from frame surfaces as necessary NOTE For parts and service call Customer Support Services at 800 351 3737 or 847 451 0036 Monday through Friday 8 00 a m to 6 00 p m Central Standard Time Please have available your name address and serial number of your product e 2007 Life Fitness a division of Brunswick Corporation All rights reserved Life Fitness is a registered trademark of Brunswick Corporation Xe SSM 10 12 07 8376701 RevA 1 L y AIIESS
13. your Product use the original shipping carton if possible 3 Write the RA on the outside of the carton 4 Insure the Product and 5 Include a letter explaining the defect or problem and a copy of your proof of purchase if you believe the service is covered by warranty Life Fitness World Headquarters Attn CSS Help Desk 5100 N River Rd Schiller Park IL 60176 EXCLUSIVE WARRANTY THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OF ANY KIND EITHER EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR PART We neither assume nor authorize any person to assume for us any other obligation or liability concerning the sale of this Product Under no circumstances shall we be liable under this warranty or otherwise for any damage to any person or property including any lost profits or lost savings for any special indirect secondary incidental or consequential damages of any nature arising out of the use of or inability to use this Product Some states do not allow the exclusion or limitation of implied warranties or of liability for incidental or consequential damages so the above limitations or exclusions may not apply to you CHANGES IN WARRANTY NOT AUTHORIZED No one is authorized to change modify or extend the terms of this limited warranty EFFECT OF STATE LAWS This warranty gives you specific legal r
Download Pdf Manuals
Related Search