Home

SH7136 Group PLQP0080JA-A User System Interface

1. Tokyo Eletech Corporation User system Figure7 Installing MCU to User System RENESAS 13 Section 5 Verifying Operation 1 Turn on the emulator according to the procedures described in the SH 2A SH 2 E200F Emulator User s Manual ROE0200F1EMUOOE or ROE571470EMUOOE 2 The emulator connected to this user system interface board supports three kinds of clock sources as the MCU clock For details refer to the SH7147 E200F Emulator User s Manual ROE0200F1EMUOOE To use the emulator internal clock Select the clock in the emulator by the CLOCK command emulator command To use the external clock on the user system Supply the external clock from the user system to the emulator by inputting the EXTAL pin pin 56 on the user system interface board or connecting the crystal oscillator to the XTAL pin 55 and EXTAL pins For details refer to section 4 Clock Pulse Generator in the SH7137 Group Hardware Manual Figure 8 shows the clock oscillator on the user system interface board To E200F emulator EXTAL XTAL System clock Figure 8 Clock Oscillator RENESAS Section 6 Notice Before connecting any parts or cables make sure that pin 1 on the both sides are correctly aligned Do not apply excessive force to the user system interface board while it is connected to the user system The dimensions of the recommended mount pad for the IC socket for this user system interface board are different from those of the
2. MCU This user system interface board is specifically designed for the SH7147 E200F EV chip unit ROE571470VKK00 Do not use this board with any other emulator When power is not supplied to the Vcc pin on the user system interface board the emulator displays VCC DOWN The emulator will not operate correctly 15 RENESAS 16 RENESAS SH7136 Group PLQP0080JA A User System Interface Board User s Manual Publication Date Rev 1 00 January 9 2008 Published by Sales Strategic Planning Div Renesas Technology Corp Edited by Customer Support Department Global Strategic Communication Div Renesas Solutions Corp 2008 Renesas Technology Corp All rights reserved Printed in Japan RenesasTechnology Corp Sales Strategic Planning Div Nippon Bldg 2 6 2 Ohte machi Chiyoda ku Tokyo 100 0004 Japan ENESAS RENESAS SALES OFFICES http www renesas com Refer to http www renesas com en network for the latest and detailed information Renesas Technology America Inc 450 Holger Way San Jose CA 95134 1368 U S A Tel lt 1 gt 408 382 7500 Fax lt 1 gt 408 382 7501 Renesas Technology Europe Limited Dukes Meadow Millboard Road Bourne End Buckinghamshire SL8 5FH U K Tel lt 44 gt 1628 585 100 Fax lt 44 gt 1628 585 900 Renesas Technology Shanghai Co Ltd Unit 204 205 AZIACenter No 1233 Lujiazui Ring Rd Pudong District Shanghai China 200120 Tel lt 86 gt 21 5877 181
3. the flexible cable for connecting this product to the emulation probe may break connector Caution for Installation O When in use do not place the emulator on its side ENESAS 4 WARNING Observe the precautions listed below Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY The USER PROGRAM will be LOST 1 Do not repair or remodel the emulator product by yourself for electric shock prevention and quality assurance 2 Always switch OFF the E200F emulator and user system before connecting or disconnecting any CABLES or PARTS 3 Always before connecting any CABLES make sure that pin 1 on both sides are correctly aligned ENESAS Preface The ROE571360CFJOO0 is a user system interface board that connects a user system for the SH7136 PLOPOOSOJA A former package FP 80WV package to the SH7147 E200F emulator ROE0200F1EMUOO or ROE571470VKK00 RENESAS Contents Section 1 1 1 1 2 0 2 2 1212 2 2 12 2 2 2 2 2 2 2 1 Section 2 Environmental Conditions eere 3 Section 3 Connection Procedures siii ici 4 3 1 Connecting User System Interface Board to User System sss 4 3 1 1 Installing IC Socket zer metet nes 4 3 1 2 Installing Cable Head iie e er lion A 5 3 1 3 Fastening Cable H 8d idet een een 5 3 2 Connecting User System Inte
4. 8 Fax lt 86 gt 21 6887 7858 7898 Renesas Technology Hong Kong Ltd 7th Floor North Tower World Finance Centre Harbour City Canton Road Tsimshatsui Kowloon Hong Kong Tel lt 852 gt 2265 6688 Fax lt 852 gt 2377 3473 Renesas Technology Taiwan Co Ltd 10th Floor No 99 Fushing North Road Taipei Taiwan Tel lt 886 gt 2 2715 2888 Fax lt 886 gt 2 3518 3399 Renesas Technology Singapore Pte Ltd 1 Harbour Front Avenue 06 10 Keppel Bay Tower Singapore 098632 Tel lt 65 gt 6213 0200 Fax lt 65 gt 6278 8001 Renesas Technology Korea Co Ltd Kukje Center Bldg 18th Fl 191 2 ka Hangang ro Yongsan ku Seoul 140 702 Korea Tel lt 82 gt 2 796 3115 Fax lt 82 gt 2 796 2145 Renesas Technology Malaysia Sdn Bhd Unit 906 Block B Menara Amcorp Amcorp Trade Centre No 18 JIn Persiaran Barat 46050 Petaling Jaya Selangor Darul Ehsan Malaysia Tel lt 603 gt 7955 9390 Fax lt 603 gt 7955 9510 Colophon 6 2 SH7136 Group PLQP0080JA A User System Interface Board User s Manual ENESAS Renesas Technology Corp 2 6 2 Ote machi Chiyoda ku Tokyo 100 0004 Japan
5. ACK080SB manufactured by Tokyo Eletech Corporation Unit mm Tolerance 1 0 mm Top view Figure 6 Resulting Dimensions after Connecting User System Interface Board when Comnecting EV Chip Unit 11 RENESAS Section 4 Installing the MCU to the User System CAUTION Check the location of pin 1 before inserting Use a Philips type screwdriver whose head matches the screw head The tightening torque must be 0 054 Nem or less If the applied torque cannot be accurately measured stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening If a screw is tightened too much the screw head may break or an IC socket contact error may be caused by a crack in the IC socket solder If the MCU does not operate correctly cracks might have occurred in the solder Check conduction with a tester and re solder the IC socket if necessary Check the location of pin 1 before inserting the MCU into the IC socket on the user system as shown in figure 7 After inserting the MCU fasten the socket cover with the provided four screws M2 0 x 6 mm Take special care such as manually securing the IC socket soldered area to prevent the IC socket from being damaged by overtightening the screws or twisting the components RENESAS Screws M2 0 x 6 mm 88 Socket cover MCU SH7136 ee C socket NQPACK080SB manufactured by
6. REJ10J1774 0100 Everywhere you imagine g 2 E N ESAS SH7136 Group PLQP0080JA A User System Interface Board ROE571360CFJOO User s Manual Renesas Microcomputer Development Environment System SuperH Family SH7137 Series Rev 1 00 R Technol Revision Date Jan 09 2008 wwwrenocaccon Notes regarding these materials This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use Renesas neither makes warranties or representations with respect to the accuracy or completeness of the information contained in this document nor grants any license to any intellectual property rights or any other rights of Renesas or any third party with respect to the information in this document Renesas shall have no liability for damages or infringement of any intellectual property or other rights arising out of the use of any information in this document including but not limited to product data diagrams charts programs algorithms and application circuit examples You should not use the products or the technology described in this document for the purpose of military applications such as the development of weapons of mass destruction or for the purpose of any other military use When exporting the products or technology described herein you should follow the applicable export control laws and regulations and procedures required by such laws and regulations All information inc
7. ackage for installing MCU 4 Screws M2 0 x 10 mm 4 For fastening board 5 Screws M2 0 x 6 mm 4 For installing a PLOPO080JA A packaged MCU 6 Guide pins 3 7 Screwdriver 1 8 User s manual 1 User s manual for ROE571360CFJ00 this manual RENESAS Section 2 Environmental Conditions Maintain the conditions in table 2 when using the emulator Table 2 Environmental Conditions Item Specifications Temperature Operating 10 to 35 C Storage 10 to 35 C Humidity Operating 35 to 80 RH no condensation Storage 35 to 80 RH no condensation Vibration Operating 2 45 m s max Storage 4 9 m s max Transportation 14 7 m s max Ambient gases There must be no corrosive gases present RENESAS Section 3 Connection Procedures 3 1 Connecting User System Interface Board to User System 4h WARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE BOARD is connected to or removed from any part Before connecting make sure that pin 1 on both sides are correctly aligned Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY The USER PROGRAM will be LOST To connect the cable head to the user system follow the instructions below 3 1 1 Installing IC Socket Solder the IC socket for a PLOPOOSOJA A package to the user system CAUTION Be sure to completely solder the leads so th
8. an authorized Renesas Technology product distributor before planning to use the product in such applications Improvement Policy Renesas Technology Corp including its subsidiaries hereafter collectively referred to as Renesas pursues a policy of continuing improvement in design performance and safety of the emulator product Renesas reserves the right to change wholly or partially the specifications design user s manual and other documentation at any time without notice ENESAS Target User of the Emulator Product This emulator product should only be used by those who have carefully read and thoroughly understood the information and restrictions contained in the user s manual Do not attempt to use the emulator product until you fully understand its mechanism It is highly recommended that first time users be instructed by users that are well versed in the operation of the emulator product Users are required to be familiar with the basic knowledge for the electric circuits logic circuits and microcomputers Precautions to be Taken when Using This Product 1 This emulator is a development supporting unit for use in your program development and evaluation stages In mass producing your program you have finished developing be sure to make a judgment on your own risk that it can be put to practical use by performing integration test evaluation or some experiment else In no event shall Renesas Solutions Corporat
9. as shall have no liability or legal responsibility for any problems caused by misuse abuse misapplication neglect improper handling installation repair or modifications of the emulator product without Renesas prior written consent or any problems caused by the user system All Rights Reserved 1 Circuitry and other examples described herein are meant merely to indicate the characteristics and performance of Renesas semiconductor products Renesas assumes no responsibility for any intellectual property claims or other problems that may result from applications based on the examples described herein 2 No license is granted by implication or otherwise under any patents or other rights of any third party or Renesas 3 This user s manual and emulator product are copyrighted and all rights are reserved by Renesas No part of this user s manual all or part may be reproduced or duplicated in any form in hard copy or machine readable form by any means available without Renesas prior written consent Figures Some figures in this user s manual may show items different from your actual system ENESAS SAFETY PAGE READ FIRST READ this user s manual before using this emulator product KEEP the user s manual handy for future reference Do not attempt to use the emulator product until you fully understand its mechanism DEFINITION OF SIGNAL WORDS Either in the user s manual or on the product several icons are us
10. at the solder slops gently over the leads and forms solder fillets Use slightly more solder than the MCU RENESAS 3 1 2 Installing Cable Head CAUTION Check the location of pin 1 before inserting Align pin 1 on the IC socket for a PLOPOOSOJA A package on the user system with pin 1 on the user system interface board and insert the user system interface board into the IC socket on the user system as shown in figure 4 3 1 3 Fastening Cable Head CAUTION 1 Use a Phillip type screwdriver whose head matches the screw head 2 The tightening torque must be 0 054 Nem or less Ifthe applied torque cannot be accurately measured stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening If a screw is tightened too much the screw head may break or an IC socket contact error may be caused by a crack in the IC socket solder If the emulator does not operate correctly cracks might have occurred in the solder Check conduction with a tester and re solder the IC socket if necessary Fasten the user system interface board to the IC socket for a PLOPOOSOJA A package on the user system with the four screws M2 0 x 10 mm provided Each screw should be tightened a little at a time alternating between screws on opposing corners Take special care such as manually securing the IC socket soldered area to prevent the soldered IC socket from being damaged by overt
11. ch of Renesas warranty See the Renesas warranty booklet for details on the warranty period This warranty extends only to you the original Purchaser It is not transferable to anyone who subsequently purchases the emulator product from you Renesas is not liable for any claim made by a third party or made by you for a third party DISCLAIMER RENESAS MAKES NO WARRANTIES EITHER EXPRESS OR IMPLIED ORAL OR WRITTEN EXCEPT AS PROVIDED HEREIN INCLUDING WITHOUT LIMITATION THEREOF WARRANTIES AS TO MARKETABILITY MERCHANTABILITY FITNESS FOR ANY PARTICULAR PURPOSE OR USE OR AGAINST INFRINGEMENT OF ANY PATENT IN NO EVENT SHALL RENESAS BE LIABLE FOR ANY DIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE OR LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE EMULATOR PRODUCT THE USE OF ANY EMULATOR PRODUCT OR ITS DOCUMENTATION EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES EXCEPT AS EXPRESSLY STATED OTHERWISE IN THIS WARRANTY THIS EMULATOR PRODUCT IS SOLD AS IS AND YOU MUST ASSUME ALL RISK FOR THE USE AND RESULTS OBTAINED FROM THE EMULATOR PRODUCT ENESAS State Law Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may have other rights which may vary from state to state The Warranty is Void in the Following Cases Renes
12. ed to insure proper handling of this product and also to prevent injuries to you or other persons or damage to your properties Their graphic images and meanings are given in this safety page Be sure to read this chapter before using the product gt This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death DANGER DANGER indicates an imminently hazardous situation which if not avoided will result in death or serious injury WARNING WARNING indicates a potentially hazardous situation which if not avoided could result in death or serious injury A CAUTION CAUTION indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury CAUTION CAUTION used without the safety alert symbol indicates a potentially hazardous situation which if not avoided may result in property damage NOTE emphasizes essential information In addition to the four above the following are also used as appropriate ENESAS A means WARNING or CAUTION Example A CAUTION AGAINST AN ELECTRIC SHOCK O means PROHIBITION Example DISASSEMBLY PROHIBITED means A FORCIBLE ACTION Example UNPLUG THE POWER CABLE FROM THE RECEPTACLE VI ENESAS 4 WARNING Warnings for AC Power Supply N If the attached AC power cable does not fit the receptacle do not al
13. haracteristics installation and other product characteristics Renesas shall have no liability for malfunctions or damages arising out of the use of Renesas products beyond such specified ranges Although Renesas endeavors to improve the quality and reliability of its products IC products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions Please be sure to implement safety measures to guard against the possibility of physical injury and injury or damage caused by fire in the event of the failure of a Renesas product such as safety design for hardware and software including but not limited to redundancy fire control and malfunction prevention appropriate treatment for aging degradation or any other applicable measures Among others since the evaluation of microcomputer software alone is very difficult please evaluate the safety of the final products or system manufactured by you In case Renesas products listed in this document are detached from the products to which the Renesas products are attached or affixed the risk of accident such as swallowing by infants and small children is very high You should implement safety measures so that Renesas products may not be easily detached from your products Renesas shall have no liability for damages arising out of such detachment This document may not be reproduced or duplicated in any form in whole or in part without pr
14. ightening the screws or twisting the components RENESAS Screws M2 0 x 10 mm Pin 1 IC socket User system NQPACK080SB manufactured by Tokyo Eletech Corporation Figure 2 Connecting User System Interface Board to User System RENESAS 3 2 Connecting User System Interface Board to EV Chip Board 4 WARNING Observe the precautions listed below Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY The USER PROGRAM will be LOST 1 Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE BOARD is connected to or removed from any part Before connecting make sure that pin 1 on both sides are correctly aligned The user system interface board dedicated to the emulator must be used 1 Make sure the user system and emulator are turned off 2 Align the connectors on the board with those on the EV chip board according to their numbers figure 3 3 Adjust the height of the spacer attached to the board with the user system RENESAS PEU EV chip unit Connector No EV Chip Unit Board Connector No Connector No User I F Connector 1 CN4 User I F Connector 2 CN5 Spacer User system Figure 3 Connecting User System Interface Board to EV Chip Board RENESAS 3 3 Recommended Dimensions for User System Mount Pad Footprint Figure 4 shows the recommended dimen
15. ion be liable for any consequence arising from the use of this emulator Renesas Solutions Corporation strives to renovate or provide a workaround for product malfunction at some charge or without charge However this does not necessarily mean that Renesas Solutions Corporation guarantees the renovation or the provision under any circumstances This emulator has been developed by assuming its use for program development and evaluation in laboratories Therefore it does not fall under the application of Electrical Appliance and Material Safety Law and protection against electromagnetic interference when used in Japan This emulator does not conform to safety standards such as UL or IEC Be careful when you take this emulator overseas Renesas cannot anticipate every possible circumstance that might involve a potential hazard The warnings in this user s manual and on the emulator product are therefore not all inclusive Therefore you must use the emulator product safely at your own risk ENESAS LIMITED WARRANTY Renesas warrants its emulator products to be manufactured in accordance with published specifications and free from defects in material and or workmanship Renesas at its option will replace any emulator products returned intact to the factory transportation charges prepaid which Renesas upon inspection shall determine to be defective in material and or workmanship The foregoing shall constitute the sole remedy for any brea
16. ior written approval from Renesas Please contact a Renesas sales office if you have any questions regarding the information contained in this document Renesas semiconductor products or if you have any other inquiries IMPORTANT INFORMATION READ FIRST READ this user s manual before using this emulator product KEEP the user s manual handy for future reference Do not attempt to use the emulator product until you fully understand its mechanism Emulator Product Throughout this document the term emulator product shall be defined as the following products produced only by Renesas Technology Corp and Renesas Solutions Corp excluding all subsidiary products e E200F main unit e External bus trace unit e Evaluation chip unit e Expansion profiling unit e Emulation memory unit e User system interface board e Trace cable The user system or a host computer is not included in this definition Purpose of the User System Interface Board This user system interface board is used to connect the evaluation chip unit to the user system This user system interface board must only be used for the above purpose Limited Applications This emulator product is not authorized for use in transportation vehicular medical where human life is potentially at stake aerospace nuclear or undersea repeater applications Buyers of this emulator product must notify Renesas Technology Corporation Renesas Solutions Corporation or
17. luded in this document such as product data diagrams charts programs algorithms and application circuit examples is current as of the date this document is issued Such information however is subject to change without any prior notice Before purchasing or using any Renesas products listed in this document please confirm the latest product information with a Renesas sales office Also please pay regular and careful attention to additional and different information to be disclosed by Renesas such as that disclosed through our website http www renesas com Renesas has used reasonable care in compiling the information included in this document but Renesas assumes no liability whatsoever for any damages incurred as a result of errors or omissions in the information included in this document When using or otherwise relying on the information in this document you should evaluate the information in light of the total system before deciding about the applicability of such information to the intended application Renesas makes no representations warranties or guaranties regarding the suitability of its products for any particular application and specifically disclaims any liability arising out of the application and use of the information in this document or Renesas products With the exception of products specified by Renesas as suitable for automobile applications Renesas products are not designed manufactured or tested for applications or otherwi
18. rface Board to EV Chip 7 3 3 Recommended Dimensions for User System Mount Pad Footprint 9 3 4 Dimensions for EV Chip Unit and User System Interface Board 10 3 5 Resulting Dimensions after Connecting User System Interface Board 11 Section 4 Installing the MCU to the User System 12 Section 5 Verifying Opern anna 14 Section Dolce aussen 15 ji RENESAS Section 1 Configuration Figure 1 and table 1 show the external appearance and components respectively of the user system interface board for the PLQPOO80JA A Please make sure you have all of these components when unpacking Screws M2 0 x 6 mm EV chip unit Socket cover IC socket User system Figure 1 User System Interface Board for the SH7136 PLOP0080JA A Package RENESAS CAUTION Use 8 socket manufactured by Tokyo Eletech Corporation and a HQPACKO080SB160 manufactured by Tokyo Eletech Corporation for the PLQP0080JA A package IC socket and socket cover respectively on the user system Table 1 ROE571360CFJ00 Components No Component Quantity Remarks 1 Board 1 With four spacers 2 6MP x 11 mm 2 IC socket 1 For the PLQP0080JA A package to be mounted on the user system 3 Socket cover 1 For the PLQPO080JA A p
19. ry or damage to the equipment Warnings to Be Taken for This Product Do disassemble or modify this product Personal injury due to electric shock may occur if this product is disassembled and modified Make sure nothing falls into the cooling fan on the top panel especially liquids metal objects or anything combustible Warning for Installation G Do not set this product in water or areas of high humidity Make sure that the product does not get wet Spilling water or some other liquid into the product may cause unrepairable damage Warning for Use Environment This equipment is to be used in an environment with a maximum ambient temperature of 35 C Care should be taken that this temperature is not exceeded Vill RENESAS A CAUTION Cautions for AC Adapter O Use only the AC adapter included in this product package The included AC adapter is for this emulator Do not use it for other product The DC plug on the included AC adapter has the below polarity 6 e The included AC adapter has no power supply switch The AC adapter is always active while connecting the AC power cable Cautions to Be Taken for This Product O Use caution when handling this product Be careful not to apply a mechanical shock Do not pull the main unit by the probe of the emulation probe or the flexible cable which are connected to this product Excessive flexing or force of
20. se in systems the failure or malfunction of which may cause a direct threat to human life or create a risk of human injury or which require especially high quality and reliability such as safety systems or equipment or systems for transportation and traffic healthcare combustion control aerospace and aeronautics nuclear power or undersea communication transmission If you are considering the use of our products for such purposes please contact a Renesas sales office beforehand Renesas shall have no liability for damages arising out of the uses set forth above Notwithstanding the preceding paragraph you should not use Renesas products for the purposes listed below 1 artificial life support devices or systems 2 surgical implantations 3 healthcare intervention e g excision administration of medication etc 4 any other purposes that pose a direct threat to human life Renesas shall have no liability for damages arising out of the uses set forth in the above and purchasers who elect to use Renesas products in any of the foregoing applications shall indemnify and hold harmless Renesas Technology Corp its affiliated companies and their officers directors and employees against any and all damages arising out of such applications You should use the products described herein within the range specified by Renesas especially with respect to the maximum rating operating supply voltage range movement power voltage range heat radiation c
21. sions for the mount pad footprint for the user system with an IC socket for a PLOPOOSOJA A package NQPACKOSOSB manufactured by Tokyo Eletech Corporation Note that the dimensions in figure 4 are somewhat different from those of the actual chip s mount pad 0 65 x 19 12 35 gt Dimension and tolerance Dimension Tolerance Up to 1 2 0 05 1 3 to 2 0 0 10 0 15 5 1 to 10 0 0 20 10 1 or above 0 30 Unit mm Figure 4 Recommended Dimensions for Mount Pad RENESAS 3 4 Dimensions for EV Chip Unit and User System Interface Board The dimensions for the EV chip unit and the user system interface board are shown in figure 5 EV chip unit Spacer Unit mm Tolerance 0 5 mm Figure 5 Dimensions for EV Chip Unit and User System Interface Board 10 RENESAS 3 5 Resulting Dimensions after Connecting User System Interface Board The resulting dimensions after connecting the user system interface board to the user system are shown in figure 6 EV chip unit IC socket Spacer 66 0 NQP
22. ter the AC power cable and do not plug it forcibly Failure to comply may cause electric shock and or fire Use an AC power cable which complies with the safety standard of the country Do not touch the plug of the AC power cable when your hands are wet This may cause electric shock This product is connected signal ground with frame ground If your developing product is transformless not having isolation transformer of AC power this may cause electric shock Also this may give an unrepairable damage to this product and your developing one While developing connect AC power of the product to commercial power through isolation transformer in order to avoid these dangers If other equipment is connected to the same branch circuit care should be taken not to overload the circuit Refer to nameplate for electrical ratings When installing this equipment insure that a reliable ground connection is maintained RENESAS VII 4 WARNING e If you smell a strange odor hear an unusual sound or see smoke coming from this product then disconnect power immediately by unplugging the AC power cable from the outlet Do not use this as it is because of the danger of electric shock and or fire In this case contact your local distributor When installing or connecting this product with other equipment shut down AC power or disconnect the AC power cord from the equipment to prevent personal inju

SH7136 Group PLQP0080JA-A User System Interface

Contents

Download Pdf Manuals

Related Search

Related Contents