Life Fitness Exercise Bike Lifecycle 8500 User's Manual
Contents
1. LIFE FITNESS EXERCISE BIKE INSTALLATION INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS DO NOT locate the Lifecycle 8500 exercise bike outdoors near swimming pools or in areas of high humidity DO NOT operate your Lifecycle 8500 bike if it has been dropped damaged or even partially immersed in water Contact Life Fitness Customer Support Services at the number on the back page of this Installation Instruction Guide DO NOT locate the Lifecycle 8500 bike any closer than 30 inches 76 cm to a television set DO NOT locate additional Lifecycle 8500 exercise bikes any closer than a minimum of 42 inches 107 cm from center to center to avoid interference cross talk between Heart Rate monitors DO keep the area around your Lifecycle 8500 bike clear of any obstructions including walls and furniture DO verify the contents of the delivery carton against the accompanying Parts List prior to setting the cartons and shipping material aside If any parts are missing contact Life Fitness Customer Support Services at the number listed in the Operation Manual Save the shipping cartons in case of return DO read the entire Operation Manual prior to attempting to operate this machine as this is essential for proper use TOOLS REQUIRED FOR ASSEMBLY Phillips screwdriver 1 2 wrench PARTS DESCRIPTION STABILIZER HANDLEBAR BOLT Qty 5 CONSOLE SCREW 0017 00101 1043 0017 00101 0932 SEAT ASSEMBLY Qty 1 COLLAR AK18 00127 0002 0K18 01152. and a Phillips screwdriver Tighten the four SCREWS in a crisscross pattern 1 4 2 gt lt CAUTION BE CAREFUL NOT TO OVERTIGHTEN THE SCREWS Step 10 To install the 9 VOLT ALKALINE BATTERY 8 found in the parts bag use a Phillips screwdriver to remove the screw from the BATTERY DOOR E Gently pull the BATTERY WIRES F from the back of the DISPLAY CONSOLE and connect themto AA ATA AAA IAS the 9 VOLT ALKALINE BATTERY Carefully tuck the BATTERY BATTERY MAY RESULT IN A MALFUNCTION OR DAMAGE WIRES back into the DISPLAY CONSOLE and set the BATTERY in place Re install the BATTERY DOOR by inserting the bottom tab of the BATTERY DOOR into the corresponding slot in the DISPLAY CONSOLE Push the DOOR into place and tighten the screw with a Phillips screwdriver CAUTION BE CAREFUL NOT TO OVER TIGHTEN THE SCREW Step 11 After placing the Lifecycle bike in the intended location for use check the stability of the bike If the bike is not stable rotate the FOOT G in the STABILIZER BAR 7 that appears to be higher until the Lifecycle bike is stable Secure the position of the FOOT by tightening the LOCKNUT with an open end wrench PRE OPERATION CHECKLIST v Insure that the STABILIZER BAR and HANDLEBAR BOLTS are tight vw Make sure the exercise bike is properly leveled and stable Before attempting to operate your Lifecycle 8500 exercise bike it is imperative that you familiarize yourself with the
3. contents of the Operation Manual If your exercise bike does not respond as described in the OPERATION MANUAL contact the nearest Life Fitness Service Center as listed in the OPERATION MANUAL LOOP 1795055 Copyright 1997 Brunswick Corporation All rights reserved Life Fitness and Lifecycle are trademarks of Brunswick Corporation M051 00K20 A052 8 97
4. 6 0001 g HANDLEBAR ASSEMBLY Qty 1 O DISPLAY CONSOLE ASSEMBLY AK18 00168 0000 AK17 00206 0001 STABILIZER BAR Qty 1 9V ALKALINE BATTERY 7 AK18 0070 0000 0017 00003 0757 Hardware included in the Parts Bag are shown here in Actual Size comm Qty 4 Qty 1 Qty 1 Qty 1 Step 1 Before proceeding familiarize yourself with the parts of the Lifecycle 8500 exercise bike and make sure that you have received all the items described in the Parts List Step 2 Remove the STABILIZER BAR 7 from the carton base Use the empty CONSOLE CARTON A to raise the rear of the Lifecycle bike as shown Remove the two BOLTS 1 from the bottom of the SHIPPING STABILIZER B save the BOLTS and store the SHIPPING STABILIZER with the other shipping containers Step 3 Use the same two BOLTS that held the SHIPPING STABILIZER in place to attach the STABILIZER BAR as shown Make certain that the BOLTS are very tight and the STABILIZER BAR is flush against the frame Remove the shipping carton Step 4 Unfold the CONSOLE WIRE HARNESS C from the HANDLEBAR POST extending from the FRAME NOTE THE COLLAR 4 SHOULD ALREADY BE IN PLACE INSTALLED ON THE HANDLEBAR ASSEMBLY 5 IF NOT INSTALL BEFORE PROCEEDING NOTE BE CAREFUL NOT TO DAMAGE THE WIRES WHEN PASSING THE BOLTS THROUGH THE HOLES TIGHTEN THE BOLTS SECURELY Step 5 Place the HANDLEBAR ASSEMBLY on the floor in front of the FR
5. AME with the two CONNECTORS 10P next to each other Align the two CONNECTORS with each other and firmly push them together until they snap into place Step 6 Position the HANDLEBAR ASSEMBLY with the COLLAR 4 in place so that the HANDLEBAR is facing away from the seat Slide the HANDLEBAR ASSEMBLY into the HANDLEBAR POST D Be careful not to pinch the wires Align the three holes in the HANDLEBAR ASSEMBLY with those in the HANDLEBAR POST and install the three HANDLEBAR BOLTS 1 Step 7 Slide the COLLAR 4 down until it completely covers the HANDLEBAR ASSEMBLY HARDWARE and the HANDLEBAR POST D Secure the COLLAR by squeezing the sides and pushing firmly downward Step 8 There is a large hole in the rear of the DISPLAY CONSOLE 6 through which you can see a 16 PIN CONNECTOR 16P and a 3 PIN CONNECTOR 3P These correspond to the respective CONNECTORS on the WIRE HARNESS protruding from the top of the HANDLEBAR Properly align the locking tabs of the 16 PIN CONNECTOR 16P on the WIRE HARNESS with the 16 PIN CONNECTOR on the back of the DISPLAY CONSOLE then snap them together Next align the locking tabs of the 3 PIN CONNECTOR 3P on the WIRE HARNESS with the 3 PIN on the back of the DISPLAY CONSOLE and push them together until they SNAP into place Step 9 Feed the WIRE HARNESS back into the HANDLEBAR TUBE Attach the DISPLAY CONSOLE to the HANDLEBAR ASSEMBLY using the four CONSOLE SCREWS 2
Download Pdf Manuals
Related Search