Life Fitness 9100R User's Manual
Contents
1. AEROBIC TRAINER INSTALLATION INSTRUCTIONS Congratulations and welcome to the world of 4 and the Lifecycle 9100R aerobic trainer The following Parts Identification Listing and the step by step installation procedures have been assembled to make the set up of your aerobic trainer as quick and easy as possible Please take special note of the following important points prior to choosing a location and beginning assembly of the Lifecycle exercise bike SAFETY FIRST DO NOT locate the Lifecycle 9100R aerobic trainer outdoors near swimming pools or in areas of high humidity DO NOT operate your Lifecycle 9100R aerobic trainer if it has been dropped damaged or even partially immersed in water Contact Life Fitness Customer Support Services at the number on the back page of this Installation Instruction Guide DO NOT locate the Lifecycle 9100R aerobic trainer any closer than 30 inches 76 cm to a television set DO keep the area around your Lifecycle 9100R aerobic trainer clear of any obstructions including walls and furniture DO verify the contents of the delivery carton against the accompanying Parts Listing prior to setting the cartons and shipping material aside If any parts are missing contact Life Fitness Customer Support Services at the number listed on the back page of this Installation Instruction Guide Save the shipping cartons in case of return DO read the entire Operation Manual prior to a2. Lifecycle in the intended location for use check the stability of the bike If the Lifecycle is not level turn a LEVELER in the rear STABILIZER BAR in either direction until the rocking motion diminishes NOTE ONLY ONE LEVELER NEEDS TO BE TURNED Stabilizer Bar Foot OPERATION CHECKLIST Insure that the STABILIZER BAR and HANDLEBAR BOLTS are tight Make sure the aerobic trainer is properly leveled and stable Read the entire Operation Manual before using the trainer English Metric Default Setting Toggle The default setting of the Lifecycle 9100R aerobic trainer display console is set to English units of measurements at the factory If your display console will require units of measurements to be in metric it may be necessary to change the setting from English to metric To do so you will need to enter into the diagnostic programs and proceed to Diagnostic State 8 To do so follow the instructions as listed below Press and continue to hold the 5 key on the keypad and then press START while pedaling the bike over 55 RPM On entry all LED s and 7 segment displays will be on You are now in Diagnostic State 1 Press the START ENTER key seven times to forward to diagnostic state 8 and choose the default setting In ALL DIAGNOSTIC STATES the user must keep pedaling the bike If the pedal RPM drops too low the bike will shut down requiring at least 40 RPM or greater and a START switch closure t
3. bly Seat Back 5 Display Console Carefully feed the wire back into the top of the HANDLEBAR ASSEMBLY and attach the DISPLAY CONSOLE to the HANDLEBAR ASSEMBLY using the four CONSOLE SCREWS 4 and a phillips screwdriver Tighten the four SCREWS in a criss cross pattern _ amp SX NOTE BE CAREFUL NOT TO OVERTIGHTEN THE SCREWS Screw 4 Handlebar Assembly Step 8 To install the 9 VOLT ALKALINE BATTERY 9 found in the parts bag use a Phillips screwdriver to remove the screw from the back door Gently pull the BATTERY WIRES from the back of the DISPLAY CONSOLE and connect them to the 9 VOLT ALKALINE BATTERY Carefully tuck the BATTERY WIRES back into the DISPLAY CONSOLE and set the BATTERY in place Re install the BATTERY DOOR by inserting the bottom tab of the BATTERY DOOR into the corresponding slot in the DISPLAY CONSOLE Push the DOOR into place and tighten the screw with a Phillips screwdriver NOTE ONLY USE AN ALKALINE TYPE BATTERY USE OF ANY OTHER TYPE BATTERY MAY RESULT IN A MALFUNCTION OR DAMAGE 9 VOLT BATTERY 9 BATTERY WIRES PHILLIPS SCREW BATTERY DOOR CAUTION BE CAREFUL NOT TO OVER TIGHTEN THE SCREW Step 9 Slide the COLLAR 6 down until it completely covers the HANDLEBAR ASSEMBLY HARDWARE and the POST extending up from the FRAME Secure the COLLAR by pinching in the sides and pushing down firmly The COLLAR will lock into place Step 10 After placing the
4. ertificate No 1 400 502 issued July 8 1986 Lifepulse and Zone Trainer are registered trademarks of Life Fitness Any use of these trademarks without the express written consent of Life Fitness is forbidden U S Patent Numbers 3 767 195 and 4 358 105 M051 00K19 A045 5 96
5. o operate again Diagnostic State 8 This test indicates the display console default setting of English or metric units of measurements When the default is set to English units of measurements it will read E in the DATA ENTRY WINDOW When the default is set to metric units of measurement it will read 9 in the DATA ENTRY WINDOW The user can change the default setting of the system by pressing the 5 key The system will toggle from an E to 9 to E condition by continuing to press the 5 key Diagnostic State 7 can be entered now by pressing the CLEAR PAUSE key and you can continue going backwards by pressing the CLEAR PAUSE key through previous diagnostics until you return to the user display Before attempting to operate your Lifecycle 9100R trainer it is imperative that you familiarize yourself with the contents of the Operation Manual If your aerobic trainer does not respond as described in the OPERATION MANUAL contact Life Fitness Customer Support Services at 800 351 3737 or 847 451 0036 Prior to your call please be sure you have located and noted the MODEL NUMBER amp SERIAL NUMBER The Model amp Serial number information of your Life Fitness 9100R aerobic trainer is contained in a label located under the center of the front stabilizer bar ALIEF 1719055 Copyright 1996 Life Fitness All rights reserved The Life Fitness trademark is registered in the U S Patent and Trademark Office C
6. the HANDLEBAR Handlebar Assembly 7 Connector Collar 6 Step 4 While holding the HANDLEBAR ASSEMBLY with the COLLAR in place in one hand feed the WIRE HARNESS at the top of the FRAME POST through the bottom of the HANDLEBAR ASSEMBLY COLUMN as shown with your other hand Continue pushing the WIRE HARNESS until the CONNECTOR at the end of the WIRE HARNESS exits through the opening at the top of the COLUMN Gently pull the WIRE HARNESS to remove the slack Step 5 Position the HANDLEBAR ASSEMBLY so that the HANDLEBAR is facing the user and slide the HANDLEBAR ASSEMBLY into the FRAME POST while being careful not to pinch the WIRES in the process Align the holes in the bottom of the HANDLEBAR ASSEMBLY with those in the FRAME POST Both the HANDLEBAR ASSEMBLY and the FRAME POST are keyed to ease the alignment and positioning Install the two HANDLEBAR BOLTS 8 to secure it into position NOTE BE VERY CAREFUL NOT TO DAMAGE THE WIRES WHEN PASSING THE BOLTS THROUGH THE HOLES TIGHTEN THE BOLTS SECURELY Step 6 There is a large hole in the rear of the DISPLAY CONSOLE 8 through which you can see a 16 PIN CONNECTOR This corresponds to the matching WIRE HARNESS CONNECTOR protruding from the top of the HANDLEBAR ASSEMBLY Properly align the LOCKING TABS of the 16 PIN CONNECTORS and plug them together until they SNAP into place Display Console 8 16 Pin Connector Wire Harness Handlebar Assem
7. ttempting to operate this machine as this is essential for proper use TOOLS REQUIRED FOR ASSEMBLY Seat Back Screw 0017 00101 1131 Handlebar Bolt 0017 00101 0986 KA Seat Back 0K19 01078 0000 Handlebar Assembly AK19 00035 0000 9V Alkaline Battery 0017 00003 0573 Phillips screwdriver 1 2 wrench 5 32 hex key wrench PARTS DESCRIPTION Seat Back Washer ll 0017 00104 0253 Console Screw i 0017 00101 1104 Collar 0K19 01125 0000 Display Console AK19 00114 0001 Hardware included in the Parts Bag are shown here in Actual Size 1 _ 7 N Gel _ yy NEL at NS ci 4 3 9 P ja EAS pra 740 Q LULU Display Console Handlebar Assembly Step 1 Align the four holes in the SEAT BACK 5 with those in the SEAT BACK POSTS Insert the four SCREWS 1 and WASHERS 2 through the backside of the SEAT Washer 2 BACK POSTS and into the SEAT BACK Tighten the aS 9 four SCREWS with a hex key wrench NOTE BE CAREFUL NOT TO OVER TIGHTEN THE SCREWS RQ Step 2 Unfold the CONSOLE WIRE HARNESS from the POST extending from the FRAME Step 3 om A i Screw 1 Slide the COLLAR 6 onto the HANDLEBAR ASSEMBLY 7 with the angled side of the COLLAR facing toward
Download Pdf Manuals
Related Search