Liebherr EWTN User's Manual
Contents
1. Figure 4 A delight in freshness 1051 EWTN 2956 7 LIEBHERR INTEGRATING CABINETRY Framed Panels Figure 5 IMPORTANT f If the thickness of the custom panels is less than If you are replacing the factory air vents with an overlay DO NOT restrict the air flow The air 1 4 6 4 mm they must be backed up with a sheet flow must be the same or greater than the fac of shim material to build the total thickness to 1 4 2 6 4 mm If the panel is thicker than 1 4 6 4 mm an edge must be routed around the panel to The door handles must be installed before the ensure a proper fit screw covers are installed If you fail to install the handles before the screw covers you can damage the covers The screw covers are taped to the unit doors during shipping Use care when removing covers The door panel weight must not exceed 25 Ib 11 3 kg 22 9 16 573 mm 6 4 mm N x max 17 1 2 445 mm 1 4 6 4 mm Jr 5 Window cutout _ 8 ala b 1 4 6 4 ba mm E N D 1 4 6 4 mm 9 gt N O 5 A delight freshness LIEBHERR WFt051 EWTN 2956 INTEGRATING CABINETRY Overlay Panels singie install Figure 6 The overlay design line allows decorative panels to cov2. Figure 27 A delight in freshness LIEBHERR 28 WF11051 EWTN 2956 SipE Bv SipE INSTALLATION 10 Figures 28 29 Slide the side installation frames 15 upward until they are in con tact with the underside of the ventilation grille Figure 28 11 Secure the side frames with the adhe sive section 17 to prevent them from sliding down Remove the protective film and place the adhesive sections over the upper brackets 12 Install anti tip brackets for each appliance Refer to Blocking For Safety Figure 28 Figure 29 A delight in freshness Wrtost EWTN 2956 29 LIEBHERR SipE Bv SipE INSTALLATION 13 Figure 30 31 Connect the appliances tothe main power supply and tothe water supply if the appliance is equipped with an IceMaker See IceMaker Water Connection Figure 30 14 Carefully slide the connected appliances into the recess until the ventilation grille touches the top Figure 31 15 Align the appliances by using only the outer lev eling wheels at the front 3 and rear 2 Figure 30 Figure 31 A delight in freshness LIEBHERR 30 EWTN 2956 SipE Bv SipE INSTALLATION 16 Figure 32 Attach the aligned combination to the surrounding ki
3. Installation Instructions For wine cooler with NoFrost freezer compartment and Side By Side Units with IceMaker Instructions de montage Armoire de mise en temp rature des vins avec cong lateur NoFrost et les appareils c te c te 000000000000000000 2 2000000001000000000000 avec IceMaker Instrucciones de instalaci n Armario de acondicionamiento de vinos con congelador NoFrost y unidades lado a lado con IceMaker WFI1051 EWTN 2956 7082 408 00 IMPORTANT PLEASE READ AND FOLLOW THESE INSTRUCTIONS These instructions contain Warning and Caution statements This information is important for safe and efficient installation Always read and follow all Warning and Caution statements m WARNING iwaw States a hazard that may cause serious injury or death if precautions are not fol lowed AN CAUTION www Signals a situation where minor injury of product damage may occur if you do not follow instructions IMPORTANT This highlights information that is especially relevant to a problem free installation Make sure incoming voltage is the same as the unit rating To reduce the risk of fire electric shock or person al injury installation work and electrical wiring must be done by a qualified electrician in accordance with all applicable codes and standards including fire rated constructi
4. 20 Star Key Torx 25 Socket Wrench 8 mm Open end Wrench 10 mm Not in package Phillips star screwdriver Level Ruler Figure 16 Installation with Ventilation Grille Set 1 Screw the installation frame at the top 1 onto the appliance with screws 2 2 Place the ventilation grille 3 on this align it in the center and secure at the front from under neath 3 Slide brackets 4 onto the side installation frames 5 from above and below 4 Using the frame 5 screw the brackets onto the side wall 5 Slide the side installation frames 5 upwards until they are in contact with the underside of the ventilation grille 6 Secure the side frames with the adhesive sec tion 7 to prevent them from sliding down Remove the protective film and affix the adhe sive sections over the upper brackets on the handle and hinge sides i 1 Depending on model and options Figure 16 A delight in freshness LIEBHERR 18 WFt051 EWTN 2956 INSTALLATION Figure 17 Connect the appliance to the 1 Carefully slide the appliance into the cabinet main power supply until the ventilation grille touches the surround If the appliance is equipped with ing kitchen cabinet IceMaker establish the connection for 2 Align the appliance until it is parallel with the the water supply See IceMaker Water surrounding kitchen cabinet Use the open Con
5. _ 25 3 16 640 mm L i E E N e 9 a co RN E S ol tt S 55 64 5 __ 22 mm R N E e LO 9 y e Y Y Y 4 19 64 19 32 109 15 mm Figure 2 A delight in freshness Wrtost EWIN 2956 5 LIEBHERR PLANNING INFORMATION Side By Side WFI 1051 RBI 1400 Figure 48 1219 mm Ls 47 3 4 1213 mm A LE 58 B 15 13 32 15 13 32 e lo e 391 mm 391 mm gt 1 1 st o p 9 N lt Y Y 1 23 32 1 23 32 44 mm 44 mm E 51 29 64 1307 mm 78 51 64 2001 mm gt 26 57 64 683 mm 48 1219 mm L 4 25 3 16 640 mm 32 25 32 832 mm 55 64 22 mm 79 15 16 2030 mm 71 1 8 1807 mm Lo x es o gt N 37 31 64 952 mm 4 19 64 19 32 109 15 mm A delight in freshness LIEBHERR 6 WFt051 EWTN 2956 ASSEMBLING DECORATIVE PANELS Figure 4 Proceed as shown in the illustration 1 Door change frames 2 Decorative panel 3 Screws for door change frames 4 Handle depending on model 5 6 D D 4 x 10 screws for handle Filler strip
6. could result in fire or electrical shock es WARNING iwaw ELECTROCUTION HAZARD Electrical Grounding Required This appli ance is equipped with a three prong grounding polarized plug for your protec tion against possible shock hazards DO NOT remove the round grounding prong from the plug e DO NOT use a two prong grounding adapter e DO NOT use an extension cord to connect power to the unit Customer s Responsibility A 115 Volt 60 Hz 15 Amp 20 Amp for side by side installation fused electrical supply is required We recommend using a dedicated circuit for this appliance to prevent electrical overload Follow the National Electrical Code and local codes and ordi nances when installing the receptacle Blocking For Safety The anti tip brackets must be installed to prevent the unit from tipping after it is installed Refer to Blocking For Safety Unit Venting DO NOT restrict the air flow Air flow must be pro vided for the unit to operate The factory air vents provide 31 square inches 200 cm of air flow per unit If you are replacing the factory air vents with an overlay the air flow must be the same or greater than the factory air vents A delight in freshness WF11051 EWTN 2956 PLANNING INFORMATION Cabinet Opening Dimensions Figure 1 pi E Allow units to open a minimum of 90 to prevent o problems removing drawers With the door open i i
7. 7 mm 6 4 mm Figure 7 A delight in freshness 1051 EWTN 2956 T LIEBHERR INTEGRATING CABINETRY Figure 8 The optional setting for the door to swing open is 90 Use this illustration to ensure other cabinets or counters do not interfere with the door opening Frameless cabinets The casing trim overlaps the cabinets at the side and top Cabinets may require filler strips to prevent interference with the cabinet door swing The door opening must allow for filler strips A delight in freshness LIEBHERR 12 WFt051 EWTN 2956 INTEGRATING CABINETRY Cabinet Appliance am 1 WF11051 EWTN 2956 3 2 25 4 mm 76 2 mm 50 8 mm 3 4 2 3 4 1 3 4 19 1 mm 69 9 mm 44 5 mm 112 2 1 2 1 1 2 12 7 mm 63 5 mm 38 1 mm 1 4 2 1 4 1 1 4 6 4 57 2 mm 31 8 1 4 6 4 mm 1 2 12 7 mm 3 4 19 1 mm 24 1 609 6 mm Z OD i euin 2 4 mm 22 0 mm 1 1 2 38 1 mm 1 4 6 4 mm 1 2 12 7 mm 3 4 19 1 mm 1 25 4 8 A delight freshness 13 Door REVERSING Door HINGES The door hinges can be changed from one side to the other if required 1 2 Figure 10 Top Unscrew the hinge pin 2 and remove the screw 5 with the eccentric Swivel out the door at the top ensuring that you do not lose the stop 7 an
8. air vents of 31 square inches 200 The door handles must be installed on the overlay panels before the screw covers are installed If you fail to install the handles on the overlay panels before the screw covers you can damage the covers The screw covers are taped to the unit doors during shipping Use care when removing covers The door panel weight must not exceed 25 Ib 11 3 kg 3 8 9mm 3 1 16 78mm pene Handle Side dee H Freezer Hinge Side T A delight in freshness 10 WFI1051 EWTN 2956 INTEGRATING CABINETRY Figure 7 Cabinet Appliance The factory setting for the door to swing open is 130 Use this illustration to ensure other cabi nets or counters do not interfere with the door opening Frameless cabinets The casing trim overlaps the cabinets at the side and top Cabinets may require filler strips to prevent interference with the cabinet door swing The door opening must m allow for filler strips 1 3 2 76 2 mm 50 8 mm 25 4 ip 2 3 4 1 3 4 de min 69 9 mm 44 5 mm it 1 1 2 12 7 mm 63 5 mm 38 1 mm mi 2 1 4 1 1 4 57 2 mm 31 8 mm 6 4 mm 1 4 6 4 mm V 1 2 lt 12 7 mm Mo KJ 3 4 oe 19 1 mm D LA SN 25 4 mm SS Y AN 1 3 0 3 32 2 4 Door n 3 4 1 2 1 4 25 4 mm 19 1 mm 12
9. side and secure them ings 8 as shown in the detailed drawing Screw on hinge 13 on the new hinge side 11 Place the lower door on the hinge pin 2 at the bottom 9 On the lower door Reinstall the door fittings Swivel in the door 14 15 Pay special attention to the part 14 Pay special attention to the bushing 12 in the with the stop center hinge 10 Insert hinge pin 9 and add the washer 11 10 12 13 Figure 12 A delight in freshness EWTN 2956 15 LIEBHERR REVERSING Door HINGES 12 Figure 13 Lift up cover 3 on handle side 14 Remove the eccentric 5 with the retaining push outward lift up cover 1 on hinge side screw in the hinge 4 and pull off 15 On the upper door Reinstall the door fittings 13 Unscrew mounting plate 21 first mounting 16 17 Pay special attention to the fitting 17 screw 20 then inner retaining screw 25 with the stop Unscrew hinge 4 first remove the mount 16 Place the upper door on the center hinge fit the ing screw 20 then retaining screws 25 Fit bushing 8 stop 7 and washer on the door hinge 4 to opposite side for easy assem swivel in the door at the top and insert and bly fit hinge from above and first tighten secure the hinge pin 2 from above through the with the upper retaining screw 25 M5 then hinge and stop screw 25 and finally mountin
10. d bushing 8 lift off the door and place it on the floor Center Pull out the hinge pin 9 with its washer Swivel out the lower door lift it out and place it on the floor Take care not to lose the stop 7 and washers 8 Unscrew all the door fittings 14 15 16 17 Figure 11 Unscrew all the door change frames and exchange them with one another 6 with 8 4 with 7 and handle remove cover 1 Secure them in position using the same screws Ensure that the door change frames are cor rectly positioned and mitered m WARNING m Make sure the corners of the door change frames are positioned correctly Sharp edges will be exposed if they are not mitered or positioned correctly Figure 10 al 8 JT 2 d A D 7 LA Y f 4 bx gt elle N 1 11 A delight freshness 14 WFI1051 EWTN 2956 REVERSING Door HINGES 8 Figure 12 Unscrew the lower hinge 13 10 Unscrew the center hinge 10 and cover 11 Remove the stop and bushings 7 8 pull them off to the side and after turning Transfer hinge pin 2 to the opposite side them 180 slide them on again on the opposite Turn the stop 7 180 and position bush
11. er the door trim for a more seamless appear ance that blends with the design of the room To achieve this look the most common way is to work 1 1 Overlay Panel 2 Spacer Panel 3 Backer Panel Approx 3 4 19 1mm 3 32 2 5mm 1 4 6 4mm W H Winecooler H Freezer 1 Overlay 23 5 16 33 5 8 38 Panel 592 mm 854 mm 965 mm 2 Spacer 21 3 4 31 1 2 36 1 4 Panel 553 mm 800 mm 921 mm 3 Backer 22 3 4 32 37 64 37 9 32 Panel b76 mm 828 mm 947 mm Window 17 1 2 25 1 2 cutout 445 mm 648 mm IMPORTANT If you are replacing the factory air vents with an overlay DO NOT restrict the air flow The air flow must be the same or greater than the factory air vents of 31 square inches 200 The door handles must be installed on the overlay panels before the screw covers are installed If you fail to install the handles on the overlay panels before the screw covers you can damage the covers The screw covers are taped to the unit doors during shipping Use care when removing covers The door panel weight must not exceed 25 Ib 11 3 kg WF11051 EWTN 2956 Figure 6 A delight in freshness 3 8 9mm 9 with three panels the decorative overlay panel a 3 32 2 5 mm spacer panel and a 1 4 6 4 mm backer panel Depending on your cabinet manufacturer this could be one panel routed for different dimensions or mo
12. g screw M4 20 17 Re insert the eccentric 5 with the retaining Turn mounting plate 21 180 and screw tight screw as shown in the detailed drawing again on the new handle side first retaining screw 25 then mounting screw 20 Check for proper alignment of all doors Adjust them if necessary using the slots on the hinge Figure 13 A delight in freshness LIEBHERR 16 WFr051 EWTN 2956 REVERSING Door HINGES Door Opening Angle Figures 14 15 The appliance is delivered with a door opening angle of 130 If the angle is to be decreased to 90 proceed as follows Insert attached screw 6 in the upper hinge as shown in Figure 14 Insert attached screw 6 in the lower hinge as shown in Figure 15 Figure 14 Figure 15 A delight in freshness WFI1051 EWTN 2956 17 INSTALLATION Only install the winecooler freezer in a stable kitch en cabinet that has been properly aligned Mount and fix the handles depending on your model and choice Unpacking Unpack the installation kit and check with the pro vided parts list if all parts are included The part numbers given in the parts list are identical to the numbers in the respective figures For installation you will need the following tools Included Star Key Torx 15 Star Key Torx
13. ht in freshness LIEBHERR 2 WFt051 EWTN 2956 INSTALLATION GUIDELINES Area Requirements Verify the following Floors can support refrigerators weight plus approximately 1200 pounds 544 kg of food weight Finished kitchen floor height has to be level Appliance must be shimmed to the floor level if the floor heights are not equal to make sure air vents are not obstructed e Remove anything attached to rear or side walls that can obstruct refrigerator opening e Cutout dimensions are accurate e Electrical outlet is in correct location Do not install this unit next to any other refrigerator or freezer except another Liebherr model Liebherr models are designed to allow side by side instal lation They are equipped with a heating system to eliminate condensation when units are installed side by side Installing this unit next to any other refrigerator or freezer can cause condensation or cause damage to the Liebherr unit Electrical Requirement If codes require a separate grounding circuit to be used have a qualified electrician install the circuit m WARNING mwa Do not ground to a gas pipe Check with a qualified electrician if you are not sure the appliance is properly grounded Do not have a fuse in the neutral or grounding circuit m WARNING mwa ELECTRICAL SHOCK HAZARD Electrically ground refrigerator Do not use an extension cord Failure to follow these instructions
14. ilation grille Figure 20 Cut out the wooden trim for use as a ventilation grille using the enclosed template The required ventilation cross sec tion must be at least 31 square inches 200 cm when a single appliance is installed which cor responds to template small If you install two appliances side by side the cross section must be at least 62 square inches 400 cm which corresponds to template double size for more information see Side by Side Installation e Remove the attachment bracket 2 from the installation frame and screw it to the appliance 1 from underneath Place the wooden ventilation grille 5 on the appliance align it in the center and secure it from the rear using the attachment bracket 2 At least 31 square inches 200cm Figure 19 Figure 20 A delight in freshness WF11051 EWTN 2956 NOTES A delight in freshness EWTN 2956 21 LIEBHERR Fon SAFETY Figure 21 Secure the appliance in place so it does not tip forward when the fully stocked door is opened Measure the distance from the floor to the upper edge of the unit Locate and mark two wall studs 1 against the wall where the refrigerator will be located The space between the unit top and the bottom of the brackets must not be more than 1 4 6 4 mm Make sure the screws 2 extend a minimum of 1 25 4 mm into each of the wall studs Make su
15. nection end wrench 10 mm 3 to adjust the feet at the front Turn clockwise for up and counterclock wise for down For the rear use the adjusting Figure 17 bolt 2 Turn clockwise for down and counter clockwise for up Maximum adjustment 19 64 15 mm 3 Figure 18 Align the appliance at the side with the cabinet side panel and attach it with screws 1 Cover the screws with cover caps 2 4 Fitthe ventilation grille at the bottom 3 if the door is hinged on the left 4 if it is on the right Secure the ventilation grille so that it touches the floor and then adjust it using the slots Figure 18 A delight in freshness Wrtost EWTN 2956 19 LIEBHERR INSTALLATION The following ventilation cross section and distances must be observed There must be a ventilation space of at least 31 square inches 200 cm per appliance in the cabinet plinth and under the cabinet top panel The depth of the ventilation duct at the rear of the cabinet must be at least 1 1 2 38 mm Alternatively 1 For built in appliances without ven tilation grilles and only with an instal lation frame ventilation must take place through the ventilation duct at the rear of the cabinet Built in appliances with an installation frame Figure 19 Screw the complete installation frame 2 to the appliance 2 Built in appliances with a wooden vent
16. ng 90 you may have to move drawers slightly to clear the door interior Electrical outlet i locati I Refer to the minimum door clearances in the Pre Installation Specifications chart Allow for a minimum 3 3 4 95 mm filler for corner installations so the door can open to 90 If you re using raised panels consider using a wider filler IMPORTANT Refer to the full scale illustrations at the end of this section for specifics on door openings and filler size alternatives E E 2904 o 3 c o Locate water supply within bottom shaded area E 3 18 E 76 457mm Q 9 L d Single 24 610mm SBS 48 1219mm Figure 1 A delight in freshness LIEBHERR 4 WFt051 EWTN 2956 PLANNING INFORMATION WFI 1051 Figure 2 24 610 mm 23 55 64 606 mm A SE E SE _ e ma tT e Ut e Lo 5 9 a2 Y 25 25 32 655 mm 39 29 64 1002 m 26 57 64 683 mm 24 610 mm
17. o the connec tion bracket 2 Secure the copper tube 3 to Figure 23 the appliance using the cable clip 5 A delight in freshness LIEBHERR 24 WFt051 EWTN 2956 SipE Bv SipE INSTALLATION Figure 24 A delight in freshness 25 WF11051 EWTN 2956 SipE Bv SipE INSTALLATION Unpacking Unpack the side by side installation kit and check with the provided parts list if all parts are included The part numbers given in the parts list are identical to the numbers in the respective figures For installation you will need the following tools Included Star Key Torx amp 15 Star Key Torx amp 20 Star Key Torx amp 25 Socket Wrench 8 mm Open end Wrench 10 mm Not in package Phillips star screwdriver Level Ruler 9 55 Figure 25 install the WFI 1051 appliances side by side proceed as follows Always place the WF WFI 1051 with the hinges on the left hand side looking from the front Installation with SBS Ventilation Grille Set 1 Affix the spacer 1 on the side wall of the appli ance remove the protective film 2 Push the appliances together align them parallel to each other 3 Use a level on the top to align them to the same height 4 Use the open end wrench 10 mm 3 to adjust the feet at the front of the roller base Turn clockwise for up and counterclockwise for down For the rear turn the adjusting b
18. olt 2 clock wise down and counterclockwise up 10 spanner Figure 25 A delight in freshness 26 WF11051 EWTN 2956 SIDE BY SIDE INSTALLATION 5 Figure 26 Secure the installation frame 3 at the top to the appliances with screws 2 Align the appliance at the front bottom Use the predrilled holes to align the installation frame 2 First mount the installation 3 frame with 4 screws 2 to one appliance then align the other appliance with the predrilled holes to the installation frame 3 and secure it with the screws 2 6 Figure 26 Position the attachment brack ets 6 at the rear of the appliances at the top and bottom Slide the upper attachment bracket upwards as far as possible Secure it at the side using the screws provided 5 Do not overtighten Figure 26 A delight in freshness 1051 EWTN 2956 27 LIEBHERR SIDE BY SIDE INSTALLATION 7 Figure 27 Push the long carriage bolt M5x260 7 through the leveling wheels as shown Fit in a washer 8 Screw on the wing nut 9 and tighten it manually Do not overtighten 8 Turn the adjustable roller base up Otherwise you will damage the floor when you push in the appliances 9 Secure the ventilation grille 10 to the appli ance with screws 11 Push in the sealing strip 4 as shown 10 spanner
19. on A delight in freshness LIEBHERR EWTN 2956 IMPORTANT WF11051 EWTN 2956 TO THE INSTALLER It is very important that the guidelines and instructions are followed in the manual to ensure proper installation and operation of the unit The Installation Guidelines section contains important information for making sure the installation is cor rect Read and understand all the information in Installation Guidelines and in this manual before the unit is installed A delight in freshness LIEBHERR TABLE CONTENTS Contents Page Installation Guidelines ULLA 3 Area 5 lt rm 3 Electrical Requirement i expedita ERA eei nS 3 Customers Responsibility 3 Blocking Foti SATCU x tpm UAI T REDDE 3 A oU 3 Planning Informatl fi sinti 4 Cabinet Opening Dimensions a 4 Assembling Decorative Panels versan 7 Integrating Cabinet 8 Framed uci Ac 8 Overlay Bac MNT 9 14 Door Opening Angle ias 17 Installall l M D 18 Blocking For EIE TE E IT 22 A 23 Water COMECION muni 23 Connection to the Water Supply eb od 24 Side By Side Installation 25 A delig
20. re likely three different panels Y ROLES x 2 2 5 Window cutout 1 9 z EY Freezer INTEGRATING CABINETRY Overlay Panels side by side install The overlay design line allows decorative panels to cover the door trim for a more seamless appear ance that blends with the design of the room To achieve this look the most common way is to work 1 Overlay Panel 1 with three panels the decorative overlay panel a 3 32 2 5 mm spacer panel and a 1 4 6 4 mm backer panel Depending on your cabinet manufacturer this could be one panel routed for different dimensions or more likely three different panels 2 Spacer Panel 3 Backer Panel Approx 3 4 19 1mm 3 32 2 5mm 1 4 6 4mm Window cutout w H Winecooler H Freezer 1 Overlay Panel 2 Spacer 23 5 16 592 mm 33 5 8 854 mm 21 3 4 31 1 2 38 965 mm 36 1 4 Winecooler Panel 553 mm 800 mm 921 mm 3 8 9mm 32 37 64 828 mm 37 9 32 947 mm 22 3 4 578 mm 3 Backer Panel max 25 1 2 648 mm max17 1 2 445 mm Window cutout IMPORTANT If you are replacing the factory air vents with an overlay DO NOT restrict the air flow The air flow must be the same or greater than the factory
21. re the anti tip brackets 3 extend at least 3 76 2 mm over the unit and are securely in place 09 aS IMPORTANT The anti tip brackets can be installed in either direction or closer together Always position the anti tip brackets as wide apart as pos sible but make sure they are anchored to two studs Using the adjustable roller base raise the unit until it makes contact with the brackets Make sure the front levelers are firmly on the floor to prevent appliance from tipping forward IMPORTANT If your unit is positioned in between the wall studs a board can be secured to the wall Make sure the board is secured to the studs with screws that will penetrate into the studs a minimum of 1 25 4 mm The board should be a minimum of 1 x 6 25 4 mm x 152 4 mm and long enough to secure both ends to the wall studs Figure 21 A delight in freshness WF11051 EWTN 2956 IceMAKER Water Connection Figure 22 Please read the first three points of the safety instructions and warnings before connecting the appliance to the main water supply The water pressure must be between 21 8 87 0 psi 1 5 6 bar Use a 1 4 OD copper line to connect the water supply to the solenoid valve This is not sup plied with the appliance Figure 22 A shut off valve such as the saddle valve illus tration here must be installed between the hose line and the main water supply so the wa
22. tchen cabinet Secure it through the side frames using the screws 20 provided Cover the screws with cover caps 21 17 Now adjust the center adjustable roller bases 22 so that they make slight contact with the floor 18 Install the lower ventilation grille 23 Secure the ventilation grille so that it touches the floor and adjust it using the slots Do not overtighten 8 spanner Figure 32 A delight in freshness Wrtost EWTN 2956 31 LIEBHERR SipE Bv SipE INSTALLATION 1 For built in appliances without ventilation grilles and only with installation frame 2 ven tilation must take place through the ventilation duct at the rear of the cabinet Ensure that the ventilation cross section is at least 31 square inches 200 cm per appliance At least 62 square inches 400 cm for side by side installation of two appliances Built in appli ances with an installation frame Figure 33 Screw the installation frame 2 to the appliance through the attachment brack ets At least 31 square inches 200cm per unit Figure 33 A delight in freshness LIEBHERR 32 EWTN 2956 SipE Bv SipE INSTALLATION Built in appliances with a wooden ventilation Remove the attachment brackets from the grille installation frame 2 and screw them to the 2 Figure 34 Cut out the wooden
23. ter sup ply can be stopped if necessary Do not install the shut off valve behind the appliance Figure 22 If you have hard water we recommend you install a water softener Also a filter must be installed if the water contains solids such as sand All equipment and devices used to supply the water to the appliance must comply with the cur rent regulations for your geographical area A delight in freshness WF11051 EWTN 2956 IceMAKER Connection to the Water Supply 3 Open the shut off valve for the water supply and check the entire water system for leaks Ns ds Aoi and auto Before the appliance is used for the first time a He MUN licensed plumber should bleed air from the sys Note tem e p ERN TEAN OL 4 Insert the electrical plug for the combined appli ance into the electrical outlet Figure 23 Pacea D4 OD copper tubing baiwa He 5 Move the appliance into final position in the shut off valve and solenoid valve Make sure there is approximately 30 70 cm of excess tubing behind the unit for easy connection room IMPORTANT The solenoid valve has a Metric R3 4 male connection A R3 4 metric to a 1 4 OD adapter and cable clip are supplied with the icemaker OE o Figure 24 Remove the cover 4 from the solenoid valve 1 Install the connection bracket 2 with sealing ring 6 on the solenoid valve 1 Attach the copper tube t
24. trim for use as appliance from underneath a ventilation grille using the attached template Place the wooden ventilation grille 5 on the The required ventilation cross section must appliance align it in the center and secure it be at least 62 square inches 400 cm for from the rear using the attachment brackets side by side installation of two appliances which corresponds to the attached template double size lt lt IK 3 11 16 93 7 mm Figure 34 A delight in freshness Wrtost EWTN 2956 33 LIEBHERR
Download Pdf Manuals
Related Search